大功率激电在承德槽子沟金矿勘查中的应用

应用大功率激电法对深部隐伏矿体的探测是一种行之有效的方法。通过激电中梯对承德槽子沟金矿区进行激电面积性测量,圈定出与金矿伴生的金属硫化物及氧化物引起的激电异常分布区带,利用激电测深查明地下极化异常体的展布,而后结合已知地质、物性资料布置验证钻孔,并取得了较好的勘查效果。本文总结出利用大功率激电方法勘查隐伏金矿的行之有效工作模式,该找矿模式可广泛应用于同类隐伏金矿的勘探之中,必将有力提高物探方法寻找隐伏金矿的勘探水平。     

激发极化法的“饱和效应”问题

西格尔（H.O.Seigel）从理论计算得到导电颗粒含量为25％的极化球体有最大异常,因此认为:激发极化法只宜于寻找中等浸染程度的矿体,对于含量很高的矿体或良导致密型矿体,激发极化法是不行的。据称这种“饱和效应”的理论得到野外结果的证实。 本文根据我国激发极化法在良导致密型矿体上大都能获得明显视极化率异常的事实,说明西格尔的“饱和效应”理论与事实不符。本文认为良导致密型极化体不存在“饱和效应”问题,激发极化法对它们的勘探也是有效的。可能由于西格尔把低含量理论公式,不计条件地推导到高含量、甚至良导矿体,因此他的结论是错误的。本文最后讨论了电阻率因素对浸染型球体视极化率强度的影响。     

松科2井东孔营城组高放射性异常层测井响应特征及成因初探

松科2井东孔是松辽盆地科学钻探工程的主体钻孔,按照计划在全井段进行地球物理测井资料采集,为深部资源勘探及白垩纪古气候、古环境研究提供准确和全面的地球物理信息.在诸多测井方法中,自然伽马测井和自然伽马能谱测井能够测量地层的天然放射性强度和铀、钍、钾元素含量等参数,被有效地应用于放射性矿床勘查,尤其是铀资源的勘查与研究;电阻率、声波、密度和中子测井等常规测井和核磁共振成像、电阻率成像、元素俘获谱测井等特殊测井能够获取地层岩性和物性参数等信息,为铀矿勘查提供有力支持.本文利用松科2井东孔自然伽马测井资料来识别高放射性异常层;基于常规测井与特殊测井资料,结合前人的地质研究成果,分析放射性异常层的特征和成因.核测井曲线指示营城组存在两段高放射性异常层,深度分别为3096.8~3102.8 m（I号层）、3168.3~3170.9 m（Ⅱ号层）.I号层自然伽马值最高达360 API,铀含量范围20.5~29.3 ppm,综合测井和岩心资料判断该层为砾岩,具有铀成矿潜力;分析表明,构造条件和后生改造作用是影响I号层铀富集的关键因素,推测断裂-火山活动和盆地抬升剥蚀为含铀地下水及油气运移至I号层提供了通道,油气的后生还原作用最终导致了I号异常层的铀富集.Ⅱ号层自然伽马值最高达250API,钍含量22.4~37.3 ppm,铀含量5.9~11.0 ppm,为集块熔岩及凝灰岩,高放射性异常可能是高钍含量的流纹质成分和粘土矿物对铀的吸附作用导致的.松科2井东孔营城组高放射性异常层具有埋藏深度深、铀含量高等特点,表明松辽盆地深部具有找铀矿前景.     

Geophysical investigation of the Sandalp rock avalanche deposits

In the study of rock avalanche phenomena, numerical modelling makes use of back analyses of the rock avalanche propagation for calibration of the modelling assumptions and parameters. The back analyses require knowledge of the run-out area boundaries and the thickness distribution of the deposit. Geophysical methods can be applied to retrieve the thickness distribution, but, due to strong heterogeneities and logistic problems they are seldom applied. The aim of this work is to assess the potential of integrated geophysical methods to recognise and characterise a deposit created by two rock avalanches which occurred in the Sandalp valley (Switzerland) in 1996. The topography of the site before and after the rock avalanche is known and can be used as a benchmark. Resistivity tomography, seismic P-wave tomography, and active and passive surface wave analysis have been applied on several profiles deployed both on the rock avalanche deposit and in the surrounding area. Innovative approaches for surface wave analysis based on laterally constrained inversion and multimodal inversion have been applied to the data. A comparison of the results of the geophysical investigations with the topographic benchmark has shown the capability of the geophysical methods to locate the bottom of the deposit in the areas where the contrast with the host sediments properties is significant. In these areas, the deposit has higher resistivities and lower seismic velocities than the underlying materials. In the areas where the deposit is thicker and richer in fine-grained materials the geophysical parameters are not able to discriminate between the rock avalanche deposit and the underlying sediments. As a secondary task, the geophysical methods also allowed the bedrock pattern to be outlined.     

秦皇岛32-6油田明化镇组河流相储层地球物理参数影响因素研究

秦皇岛32-6油田明化镇组储层为河流相沉积,单砂体规模小,砂体间接触关系复杂,受到地震分辨率限制,对叠置砂体储层地震响应规律认识不明确,导致基于地震信息的储层砂体解释错误.通过数值正演模拟,可以正确认识砂体储层的地震响应规律,提高砂体储层预测的准确率.所以,在进行地震响应正演模拟前,非常有必要对该区储层地球物理参数影响因素展开研究,通过分析研究区14口测井资料,建立了岩石物理参数(孔隙度、泥质含量、合流体性)与地球物理参数(速度、密度、波阻抗等)之间的相关关系,分析了不同沉积微相对地球物理参数的控制作用,并给出了相应的数学表达式,为正确认识河流相储层砂体地震响应规律奠定了准确的地球物理参数基础.     

STATISTICAL TECHNIQUES APPLIED TO BOREHOLE GEOPHYSICAL DATA IN GOLD EXPLORATION1

Gold, as a trace element, is not directly detectable by geophysical borehole logging techniques. Geophysical logging methods have therefore been used to infer the presence of structural features and alteration processes associated with gold. Since these features and processes differ with the style of gold mineralization, a unique relation between geophysical anomalies and gold cannot be established. However, in a particular environment, such an association can be established. We examined geophysical log data (self potential, induced polarization, resistivity, gamma, temperature, and temperature gradient) and drill core from the Barber-Larder property in NE Ontario. The geophysically detectable alteration processes associated with gold were identified as sericitization and pyritization, by means of factor analysis. A linear discriminant function was constructed which allowed the zones of economic mineralization (nominally 0.05 oz/ton or 1.5 ppm) to be identified with a 75% success rate based on geophysical log data alone. This rate was achieved without sophisticated non-linear data transformations.     

Surface NMR within a geophysical study of an aquifer at Haldensleben (Germany)

The surface nuclear magnetic resonance (SNMR) method has been tested at a site in Haldensleben, northern Germany, to assess the suitability of this new method for groundwater exploration and environmental investigations. More information is obtained by SNMR, particularly with respect to aquifer parameters, than with other geophysical techniques. SNMR measurements were carried out at three borehole locations, together with 2D and 1D direct current geoelectrics, as well as ground-penetrating radar, and well logging (induction log, gamma-ray log and pulsed neutron-gamma log). Permeabilities were calculated from the grain-size distributions of core material determined in the laboratory. It is demonstrated that the SNMR method is able to detect groundwater and the results are in good agreement with other geophysical and hydrogeological data. Using the SNMR method, the water content of the unsaturated and saturated zones (i.e. porosity of an aquifer) can be reliably determined. This information and resistivity data permit in situ determination of other aquifer parameters. Comparison of the SNMR results with borehole data clearly shows that the water content determined by SNMR is the free or mobile water in the pores. The permeabilities estimated from the SNMR decay times are similar to those derived from sieve analysis of core material. Thus, the combination of SNMR with geoelectric methods promises to be a powerful tool for studying aquifer properties.     

Compressional-wave Q estimation from full-waveform sonic data

There is significant evidence that the anelastic loss of seismic energy is linked to petrophysical properties such as porosity, permeability and clay content. Thus, reliable estimation of anelastic attenuation from seismic data can lead to improved methods for the prediction of petrophysical properties. This paper is concerned with methods for the estimation of attenuation at sonic frequencies (5–30 KHz) from in situ data. Two independent methods have been developed and tested for estimating compressional‐wave attenuation from full‐waveform sonic data. A well‐established technique, the logarithm spectral ratio (LSR) method, is compared with a new technique, the instantaneous frequency (IF) method. The LSR method uses the whole spectrum of the seismic pulse whilst the IF method uses a carefully estimated value of instantaneous frequency which is representative of the centre frequency of the pulse. In the former case, attenuation estimation is based on the relative variation of amplitudes at different frequencies, whilst in the latter case it is based on the shift of the centre frequency of the pulse to lower values during anelastic wave propagation. The IF method does not assume frequency independence of Q which is a necessary assumption for the LSR method, and it provides a stable frequency log, the peak instantaneous frequency (PIF) log, which may be used as an indicator for attenuation under certain limitations. The development and implementation of the two methods is aimed at minimizing the effect of secondary arrivals, such as leaky modes, and involved a series of parameter tests. Testing of the two methods using full‐waveform sonic data of variable quality, obtained from a gas‐bearing sandstone reservoir, showed that the IF method is in general more stable and suitable for full‐waveform sonic data compared with the LSR method. This was evident especially in data sets with high background noise levels and wave‐interference effects. For good quality data, the two methods gave results that showed good agreement, whilst comparison with other log types further increased confidence in the results obtained. A significant decrease (approximately 5 KHz) in the PIF values was observed in the transition from an evaporite/shale sequence to the gas‐bearing sandstone. Average Q values of 54 and 51 were obtained using good quality data from a test region within the gas‐saturated sandstone reservoir, using the LSR and IF methods, respectively.     

致密砂岩气藏裂隙-孔隙型弹性岩石物理模板研究:以川西坳陷A区为例

相对于常规砂岩,致密砂岩在岩石物理性质、力学性质等方面具有明显差异,并呈现出很强的非均质性.岩石物理模型能将储层参数与地震特性信息联系起来,因此可以作为致密砂岩储层参数与地震特性信息转换的桥梁.常规的岩石物理模型通常只考虑单一因素(例如非均匀性,单一孔隙,单一尺度等),建立的岩石物理模板并不适用于致密砂岩.本文针对高饱和气、微裂隙发育、非均质性强的致密砂岩储层,利用Voigt-Reuss-Hill模型计算混合矿物的弹性模量,采用微分等效介质(DEM)模型描述含裂隙、孔隙岩石的骨架弹性模量,基于Biot-Rayleigh波动方程构建了岩石物理弹性模板,给出了致密砂岩储层弹性参数与物性的关系.基于测井数据和实验数据对岩石物理弹性模板进行校正,并将校正后的岩石物理弹性模板结合叠前地震资料应用于川西地区储层孔隙度与裂隙含量预测.结果显示,反演裂隙含量、孔隙度与储层试气报告、测井孔隙度基本吻合,表明该模板能够较合理地应用于致密砂岩储层孔隙度及裂隙含量解释中.     

SOME APPLICATIONS OF IP-TECHNIQUE FOR DIFFERENT GEOPHYSICAL PROSPECTING PURPOSES *

The usefulness of IP-technique for different geophysical purposes is discussed on the basis of field examples. IP and resistivity results are not always correlated, and the IP-information may be unique in prospecting for very low grade sulphide mineralizations. The IP-technique seems to be useful sometimes in prospecting for disseminated Ni-Cu- mineralizations. A massive sulphide mineralization could be localized using IP. The disturbances from different kinds of geological objects other than prospecting targets generally are smaller in IP-work than in resistivity work. It was possible to discriminate between apparent resistivity anomalies caused by shear zones and by sulphide mineralizations by means of IP-measurements. The influence of magnetite on IP- measurements is briefly discussed. The relation between ground magnetic measurements ΔZ and the IP-parameter is in many areas weak and does not seriously influence the interpretation of the IP-measurements. A high correlation between ΔZ and IP-measurements has been found on a titaniferous iron ore. This ore body gives strong IP-anomalies indicating that it is a good IP-target. Finally, the application of small moving arrays in very detailed IP-measurements is found useful for detailed mapping of a mineralized zone under a thin overburden and for determination of the dip of mineralized zones.     

Modeling unsaturated flow in a layered formation under quasi-steady state conditions using geophysical data constraints

The identification of vadose zone flow parameters and solute travel time from the surface to the water table are key issues for the assessment of groundwater vulnerability. In this paper we use the results of time-lapse monitoring of the vadose zone in a UK consolidated sandstone aquifer using cross-hole zero-offset radar to assess and calibrate models of water flow in the vadose zone. The site under investigation is characterized by a layered structure, with permeable medium sandstone intercalated by finer, less permeable, laminated sandstone. Information on this structure is available from borehole geophysical (gamma-ray) logs. Monthly cross-hole radar monitoring was performed from August 1999 to February 2001, and shows small changes of moisture content over time and fairly large spatial variability with depth. One-dimensional Richards’ equation modeling of the infiltration process was performed under spatially heterogeneous, steady state conditions. Both layer structure and Richards’ equation parameters were simulated using a nested Monte Carlo approach, constrained via geostatistical analysis on the gamma-ray logs and on a priori information regarding the possible range of hydraulic parameters. The results of the Monte Carlo analysis show that, in order to match the radar-derived moisture content profiles, it is necessary to take into account the vertical scale of measurements, with an averaging window size of the order of the antenna length and the Fresnel zone width. Flow parameters cannot be uniquely identified, showing that the system is over parameterized with respect to the information content of the (nearly stationary) radar profiles. Estimates of travel time of water across the vadose zone are derived from the simulation results.     

Pressure effects on the joint elastic‐electrical properties of reservoir sandstones

We conducted a laboratory study of the joint elastic‐electrical properties of sixty‐three brine‐saturated sandstone samples to assess the likely impact of differential pressure (confining minus pore fluid pressures) in the range 8–60 MPa on the joint interpretation of marine seismic and controlled‐source electromagnetic survey data. The samples showed a wide range of petrophysical properties representative of most sandstone reservoirs. We found that a regression equation comprising both a constant and an exponential part gave a good fit to the pressure dependence of all five measured geophysical parameters (ultrasonic P‐ and S‐wave velocity, attenuation and electrical resistivity). Electrical resistivity was more pressure‐sensitive in clay‐rich sandstones with higher concentrations of low aspect ratio pores and micropores than in clean sandstones. Attenuation was more pressure‐sensitive in clean sandstones with large open pores (macropores) than in clay‐rich sandstones. Pore shape did not show any influence on the pressure sensitivity of elastic velocity. As differential pressure increases, the effect of the low aspect ratio pores and micropores on electrical resistivity becomes stronger than the effect of the macropores on attenuation. Further analysis of correlations among the five parameters as a function of pressure revealed potentially diagnostic relationships for geopressure prediction in reservoir sandstones.     

Identification of coal seam strata from geophysical logs of borehole using Adaptive Neuro-Fuzzy Inference System

Different parameters obtained through well-logging geophysical sensors such as SP, resistivity, gamma–gamma, neutron, natural gamma and acoustic, help in identification of strata and estimation of the physical, electrical and acoustical properties of the subsurface lithology. Strong and conspicuous changes in some of the log parameters associated with any particular stratigraphy formation, are function of its composition, physical properties and help in classification. However some substrata show moderate values in respective log parameters and make difficult to identify or assess the type of strata, if we go by the standard variability ranges of any log parameters and visual inspection. The complexity increases further with more number of sensors involved.An attempt is made to identify the type of stratigraphy from borehole geophysical log data using a combined approach of neural networks and fuzzy logic, known as Adaptive Neuro-Fuzzy Inference System. A model is built based on a few data sets (geophysical logs) of known stratigraphy of in coal areas of Kothagudem, Godavari basin and further the network model is used as test model to infer the lithology of a borehole from their geophysical logs, not used in simulation. The results are very encouraging and the model is able to decipher even thin cola seams and other strata from borehole geophysical logs. The model can be further modified to assess the physical properties of the strata, if the corresponding ground truth is made available for simulation.     

A LABORATORY INVESTIGATION OF THE INDUCED POLARIZATION OF THE TRIASSIC SHERWOOD SANDSTONE OF LANCASHIRE AND ITS HYDROGEOLOGICAL APPLICATIONS*

The time-domain induced polarization (IP) of saturated Sherwood Sandstone correlates significantly with the intergranular permeability and the matrix conductivity but only at low electrolyte concentrations (< 500 p.p.m. NaCl). An increase in the magnitude of sandstone IP with increase in the valence of the electrolyte cation is pronounced but occurs only at intermediate concentrations, i.e., between 100 and 2500 p.p.m. Surface IP and resistivity depth sounding measurements, supplemented by data from laboratory measurements, can be used to estimate the groundwater conductivity and hence the salinity in a moderate to strongly saline sandstone aquifer.     

Research on diagenesis of the sandstone-type uranium deposits in Dongsheng area,Ordos Basin

Synthetic methods of thin section petrography, scanning electron microscope, electron microprobe, energy spectrum analysis, cathodoluminescence, isotopic analysis and temperature measuring for fluid inclusions were used in analyzing sandstone samples collected from the Zhiluo Formation in order to fully understand the diagenesis evolution and the mineralizing response as well as the genesis of the uranium-bearing sandstone in Dongsheng area. The result shows that (1) the sandstone include lithic silicarenite, feldspathic litharenite and litharenite; (2) the authigenic minerals include clay minerals, carbonate minerals, siliceous and ferric minerals; (3) the physical property of sandstone is obviously controlled by diagenesis; and (4) the sandstone with favorable physical property is propitious to migration and storage of ore-forming fluid, and finally, forming the ore deposit. The sandstone of the Zhiluo Formation had undergone the early diagenetic stage (periods A and B) and the epidiagenetic stage. The evolution of diagenetic environment is in the order of acidic oxidation, alkalescent deoxidization, acidity to transitional environment of oxidation-deoxidization and acidity-alkalescence. The uranium exists in forms of pre-enrichment uranyl ion, active uranyl ion, dispersive adsorptive uranium and uranium mineral, respectively. In addition, the authors also hold that the formation of the sandstone-type uranium is not only related to the oxidation-deoxidization environment, but also closely related to the acidic-alkaline transitional environment, which are propitious to uranium mineralization in sandstone.     

Research on diagenesis of the sandstone-type uranium deposits in Dongsheng area, Ordos Basin

Synthetic methods of thin section petrography, scanning electron microscope, electron microprobe, energy spectrum analysis, cathodoluminescence, isotopic analysis and temperature measuring for fluid inclusions were used in analyzing sandstone samples collected from the Zhiluo Formation in order to fully understand the diagenesis evolution and the mineralizing response as well as the genesis of the uranium-bearing sandstone in Dongsheng area. The result shows that (1) the sandstone include lithic silicarenite, feldspathic litharenite and litharenite; (2) the authigenic minerals include clay minerals, carbonate minerals, siliceous and ferric minerals; (3) the physical property of sandstone is obviously controlled by diagenesis; and (4) the sandstone with favorable physical property is propitious to migration and storage of ore-forming fluid, and finally, forming the ore deposit. The sandstone of the Zhiluo Formation had undergone the early diagenetic stage (periods A and B) and the epidiagenetic stage. The evolution of diagenetic environment is in the order of acidic oxidation, alkalescent deoxidization, acidity to transitional environment of oxidation-deoxidization and acidity-alkalescence. The uranium exists in forms of pre-enrichment uranyl ion, active uranyl ion, dispersive adsorptive uranium and uranium mineral, respectively. In addition, the authors also hold that the formation of the sandstone-type uranium is not only related to the oxidation-deoxidization environment, but also closely related to the acidic-alkaline transitional environment, which are propitious to uranium mineralization in sandstone.     

Geophysical imaging of a kaolinite deposit at Sylvan,Manitoba, Canada

A geophysical survey was performed at Sylvan, Manitoba, Canada (51°5′N, 97°22′W) to investigate a Lower Cretaceous kaolinite deposit. The deposit consists of zones of kaolinite, silica sand, and lignitic clay located in a series of channels formed during karsting of the underlying Palaeozoic bedrock and is covered by 3 to 5 m of glacial drift. The aim of the study was to identify cost-efficient electrical and electromagnetic (EM) geophysical methods for locating, mapping, and assessing this target. Methods applied included terrain conductivity (EM31), VLF-EM, time-domain electromagnetics (TEM), DC-resistivity, and shallow seismic refraction. The survey showed that EM methods offer a viable alternative to more expensive seismic reflection surveys in the investigation of small industrial mineral deposits. Comparison of the geophysical survey results with those of a drilling program indicated that VLF-EM and TEM were the best methods for delineating the kaolinite deposit. VLF-EM was the most cost-efficient method for delineating the kaolinite deposit over a ca. 10 ha area and for exploring for further deposits within several kilometers of the main site. Joint interpretation of the in-phase and quadrature response is required for increased reliability in identifying the major kaolinite-filled channels. The TEM method provided more detailed resolution of the deposit than VLF-EM and was the optimal method for assessing its thickness. However, TEM data acquisition is too slow and inefficient for reconnaissance mapping of 10 ha sites. EM31 surveying is useful for defining the palaeokarst surface and overburden thickness in areas surrounding the deposit but cannot be used reliably for mapping the kaolinite deposit itself. The combined geophysical survey results show the kaolinite deposit at Sylvan to be located in a channel which is 100 m wide and about 25 m deep. The deposit has a bulk electrical conductivity between 13 mS m⁻¹ and 25 mS m⁻¹ consistent with low cation exchange capacity values measured for the kaolinite. The palaeokarst surface surrounding the deposit contains a series of sinuous, discontinuous, depressions with a depth variations of several meters.     

Potential Field,Geoelectrical and Reflection Seismic Investigations for Massive Sulphide Exploration in the Skellefte Mining District,Northern Sweden

Multi-scale geophysical studies were conducted in the central Skellefte district (CSD) in order to delineate the geometry of the upper crust (down to maximum ～ 4.5 km depth) for prospecting volcanic massive sulphide (VMS) mineralization. These geophysical investigations include potential field, resistivity/induced polarization (IP), reflection seismic and magnetotelluric (MT) data which were collected between 2009 and 2010. The interpretations were divided in two scales: (i) shallow (～ 1.5 km) and (ii) deep (～4.5 km). Physical properties of the rocks, including density, magnetic susceptibility, resistivity and chargeability, were also used to improve interpretations. The study result delineates the geometry of the upper crust in the CSD and new models were suggested based on new and joint geophysical interpretation which can benefit VMS prospecting in the area. The result also indicates that a strongly conductive zone detected by resistivity/IP data may have been missed using other geophysical data.     

Research on diagenesis of the sandstone-type uranium deposits in Dongsheng area,Ordos Basin

Synthetic methods of thin section petrography, scanning electron microscope, electron microprobe, energy spectrum analysis, cathodoluminescence, isotopic analysis and temperature measuring for fluid inclusions were used in analyzing sandstone samples collected from the Zhiluo Formation in order to fully understand the diagenesis evolution and the mineralizing response as well as the genesis of the uranium-bearing sandstone in Dongsheng area. The result shows that (1) the sandstone include lithic silicarenite, feldspathic litharenite and litharenite; (2) the authigenic minerals include clay minerals, carbonate minerals, siliceous and ferric minerals; (3) the physical property of sandstone is obviously controlled by diagenesis; and (4) the sandstone with favorable physical property is propitious to migration and storage of ore-forming fluid, and finally, forming the ore deposit. The sandstone of the Zhiluo Formation had undergone the early diagenetic stage (periods A and B) and the epidiagenetic stage. The evolution of diagenetic environment is in the order of acidic oxidation, alkalescent deoxidization, acidity to transitional environment of oxidation-deoxidization and acidity-alkalescence. The uranium exists in forms of pre-enrichment uranyl ion, active uranyl ion, dispersive adsorptive uranium and uranium mineral, respectively. In addition, the authors also hold that the formation of the sandstone-type uranium is not only related to the oxidation-deoxidization environment, but also closely related to the acidic-alkaline transitional environment, which are propitious to uranium mineralization in sandstone.

     

日龙沟锡—多金属成矿区综合物探找矿方法应用研究

通过对日龙沟锡—多金属矿区物探工作的研究分析,结合地质物探工作,提出了在日龙沟寻找磁黄铁矿化热液改造型锡—多金属矿床的找矿标志和工作方法.利用该方法对矿区外围进行验证,认为矿区外围成矿条件优越,已有多个钻孔见矿.因此,可以总结出该区域寻找此类型矿体的地球物理预测模型,为该区今后的找矿工作提供经验.