Undrained monotonic shear behavior of marine soft clay after long-term cyclic loading

Abstract

In the coastal area, nearshore and offshore structures have been or will be built in marine soft clay deposits that have experienced long-term cyclic loads. Therefore, the mechanical behavior of marine clay after long-term cyclic loading needs to be investigated. In this research, a series of monotonic and cyclic triaxial tests were carried out to investigate the postcyclic mechanical behavior of the marine soft clay. The postcyclic water pore pressure, shear strength and secant stiffness are discussed by comparing the results with the standard monotonic test (without cyclic loading). It is very interesting that the postcyclic behavior of marine soft clay specimen is similar to the behavior of overconsolidated specimen, that is, the specimen shows apparent overconsolidation behavior after long-term cyclic loading. Then relationship between the overconsolidation ratio and the apparent overconsolidation ratio is established on the basis of the theory of equivalent overconsolidation. Finally, a validation formula is proposed which can predict the postcyclic undrained shear strength of marine soft clay.     

Estimation of Uplift Capacity of Rapidly Loaded Plate Anchors in Soft Clay

Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors.     

Laboratory study on cement admixed marine silt bricks

For the purpose of efficient utilization of sediments dredged from harbor, a new method was proposed in this study. Marine silt bricks were made by mixing sediments with cement and gypsum, placing it in a cubic mold with 240 mm in length, 115 mm in width, and 53 mm in height, and curing for certain days. To investigate the effects of cement and initial water content of soil on the mechanical behavior of marine silt bricks, unconfined compressive and flexural strength tests were carried out. Given the same curing time and cement content, the higher the initial water content, the lower the compressive and flexural strength. After 60 days of curing, the compressive strength of marine silt bricks with cement content = 20% and water content = LL (liquid limit) reached approximately 5 MPa. The flexural strength was relatively low. The flexural strength of marine silt bricks with 20% cement and water content = LL was around 1.5 MPa. The compressive and flexural strength decreased with the increase of water/cement ratio. As for the curing time, longer curing time had a positive impact on the compressive strength. The ratio of flexural to compressive strength varied slightly in the range of 0.4–0.5.     

Enhancing the mechanical properties of marine clay using cement solidification

Abstract

The use of soft clay and dredged marine clays as the construction material is challenging. This is because the high water content, high compressibility and low permeability of the clay causing the instability of ground and structure. This detrimental effect of soft clay can be improved by the cement solidification process, which is relatively cheap and efficient. This paper mainly focuses on the study of improvement on the mechanical behavior of cement mixed marine clay. The soil is reconstituted by using ordinary Portland cement of 5%, 10%, 15% and 20% by its mass. The study reveals that cementation of clay significantly improves the peak and residual strength of soil. Similarly, the primary yield stress of the soil is also improved from 16 to 275?kPa as cement content increases from 5% to 20%, respectively. By using statistical tools, the relationships between various parameters are established, which are very important to define the mechanical behavior of the clay. This study reveals that the yield surface of the solidified marine clay is not a smooth elliptical surface. Rather it is composed of two linear surfaces followed by a log-linear surface which can be modeled by using simple parameters obtained from triaxial tests.     

Behavior of a helical anchor under vertical repetitive loading

Abstract

In the field of ocean engineering, anchors are used for several purposes. This article studies the behavior of a helical anchor embedded in soft marine clay under vertical repetitive loading. Helical anchors are simple steel shafts to which one or more helical plates are attached at regular intervals. The tests are conducted on a model helical anchor installed in a soft marine clay bed prepared in a test tank. Repetitive loading is applied using a pneumatic loading arrangement. Different cyclic load ratios and time periods are adopted. In each test, after the application of repetitive loading, poststatic‐pullout tests are conducted to observe the effect of repetitive loading on anchor behavior. From the test results, it is found that, up to a cyclic load ratio of 55%, there is no reduction in capacity. Instead, there seems to be a marginal increase in capacity and reduction in displacement. The reasons for this behavior are explained in terms of induced changes in strength and deformation behavior of marine clay under repetitive load. However, at higher cyclic load ratios, there seems to be reduction in pullout capacity of the anchor, and the reason for this is explained in terms of strain criteria. From this investigation, it can be concluded that the deep anchor is more suitable to a marine environment than a shallow anchor.     

Field Evaluation of Undrained Shear Strength from Piezocone Penetration Tests in Soft Marine Clay

The use of the piezocone penetration test (CPTU) in a geotechnical site investigation offers direct field measurement on stratigraphy and soil behavior. Compared with some traditional investigation methods, such as drilling, sampling and field inspecting method or laboratory test procedures, CPTU can greatly accelerate the field work and hereby reduce corresponding operation cost. The undrained shear strength is a key parameter in estimation of the stability of natural slopes and deformation of embankments in soft clays. This paper provides the measurements of in situ CPTU, field vane testing and laboratory undrained triaxial testing of Lianyungang marine clay in Jiangsu province of China. Based on the literature review of previous interpretation methods, this paper presents a comparison of field vane testing measurements to CPTU interpretation results. The undrained shear strength values from both the field vane tests and cone penetration resistances are lowest at the mid-depths of the marine clay layers, and the excess pore water pressures are highest at the mid-depths of the marine clay layers, indicating that the marine clay layer is underconsolidated.     

Experimental simple shear study of composite soil with cemented soil core

Abstract

Cement soil mixing piles are an effective treatment method for marine soft clay. To investigate the static and dynamic characteristics of the composite soil with cemented soil core, a series of experiments are carried out by using the cyclic simple shear test. The result shows that, the static shear strain showed strain hardening, cemented soil core can improve static shear strength of composite soil, vertical stress can enlarge reinforcement of cemented soil core. The tendency of strain development of composite soil with different area replacement ratios under cyclic loading is the same as that of pure clay, existing critical cyclic stress ratios corresponding to different area replacement ratios. In addition, improving area replacement ratio can increase cyclic strength. At same time, adding of cemented soil core does not change shape of hysteresis curve compared with it for clay either. Moreover, cemented soil core can also obstruct stiffness softening. Through regression analysis of the experimental data, relationship between cyclic number and soil softening index is proved to be linear. The results can give a reference for the dynamic characters of the marine soft clay foundation with cement soil mixing piles.     

Response of Single Piles in Marine Deposits to Negative Skin Friction from Long-term Field Monitoring

The behavior of single piles subjected to negative skin friction in soft soil was conducted by analyzing the results from full-scale long-term field measurements and three-dimensional (3D) numerical analyses. A skin friction coefficient (α and β coefficients) of the instrumented piles is back-calculated at different degrees of consolidation (U) of soft marine clay. Back-calculated β-values ranged from 0.15 to 0.35 for clay, and from 0.30 to 0.55 for sand, respectively. In addition, back-calculated α-values ranged from 0.1 to 0.3 for coated pile, and from 0.2 to 0.8 for uncoated pile when undrained shear strength of the soft clay was about 30–60 kPa, respectively. Moreover, this study describes behavior of a pile based on full-coupled 3D finite element (FE) analysis. The appropriate parametric studies needed for verifying the pile-soil interaction with consolidation are presented in this paper. Compared to the results from the measurements, it is shown that the computed results are capable of predicting the pile-soil behavior under consolidation. The major parameters that influence the pile behavior are discussed for different soil-pile conditions.     

Effect of angle between initial and cyclic shear stress on behaviors of marine clay

An angle exists between the initial static shear stress and cyclic shear stress when embankment and retaining walls are subjected to cyclic loadings. To investigate the influence of this angle on the dynamic properties of marine soft clay, tests were performed on Wenzhou soft clay. When the angle was varied from 0° to 90°, the shear strain and excess pore pressure decreased as θ increased while increased as θ increased from 120° to 180°. Shear strain developed more rapidly when θ was 120°, 150°, or 180° than that when θ was 0°, 30°, or 60°. These results indicate that the number of cycles to failure at the larger angles was greater than at the smaller angles. When θ was 90°, the strain in the x-axis direction increased as the number of cycles increased. The development of the excess pore pressure associated with specimen failure was different for different cyclic shear stress ratios and shearing angles. The effect of θ on the strain and excess pore pressure increased as the cyclic shear stress ratio increased.     

Secondary Compression Features of Jiangsu Soft Marine Clay

The results of one-dimensional compression tests conducted on undisturbed specimens of Jiangsu soft marine clay is presented. Because of its high in situ void ratios and natural water content, Jiangsu soft marine clay displays high values of both the virgin compression index, C_c, and the secondary compression coefficient, C_α. The laboratory data indicates that the value of the ratio C_α/C_c for Jiangsu soft marine clay is constant. However, neither C_α nor C_c are constant: they both depend upon the natural water content (or void ratio) and thus are also dependent on the deformation (or compression) of Jiangsu soft marine clay. Settlement analyses show that the secondary settlement of Jiangsu soft marine clay is a significant component of the field settlement. The concept of a constant value for C_α/C_c is used to predict the secondary settlement of a surcharged embankment founded upon Jiangsu soft marine clay. The predictions are in agreement with the limited post-construction field measurements of the embankment settlement.     

Centrifugal Modeling of an Embankment Backfilled with Lime-Stabilized Soil on Marine Clay

A centrifugal model test was performed for an embankment backfilled with lime-stabilized soil on an undisturbed marine clay foundation. During the test, in-flight photographs were captured, settlements were measured by displacement sensors, and displacement contours were obtained from the markers installed on the front face of the model foundation. These test data were analyzed and discussed in this paper. The test results show that the embankment was stable at 2 m height but ruptured during the loading from 2 to 4 m height. The ratio of the maximum horizontal displacement increment to the ground settlement increment at the embankment centerline suddenly increased during the loading from 4 to 6 m height, indicating the failure of the foundation. This result is in agreement with the observation of the centrifugal test and the calculated Terzaghi ultimate bearing capacity under an undrained condition. Considering the brittle behavior and low tensile strength of the lime-stabilized soil, it is recommended that the lime-stabilized soil should only be used for a low embankment with a height less than 2 meters.     

Effect of Pollutants on the Physical and Engineering Behavior of Lime-Treated Marine Clay

Abstract

Rapid industrial growth and increasing population has resulted in the discharge of wastes into the ocean, wastes which ultimately reach the seabed and contaminate the marine sediments. The soil-contaminants interaction, and their associated physico chemical properties with sediments control the behavior of marine clays. Marine clay deposits of low strength and high compressibility are located in many coastal and offshore areas. There are several foundation problems encountered in these weak marine clays. In this study, experimental work was carried out in the laboratory to stabilize soft marine clays using the lime column technique. Also the lime-induced effects on the physical and engineering behavior of marine clays in sulfate-contaminated marine environment was investigated. Consolidation tests indicate that compressibility of the lime-treated samples was reduced to 1/2–1/3 of the virgin soil after 45 days treatment. The test results also suggest that the lime column technique can be conveniently used to improve the behavior of contaminated marine clay deposits.     

往复荷载作用下软粘土中浅埋管道的稳定性的振动台模型试验研究

软粘土在波浪荷载作用下,可能发生强度软化,使埋设在软粘土层中的海底管道的受力状态或支撑条件发生变化,从而出现上浮或下沉的趋势,对管道的稳定性发生影响。本文通过在振动台上进行的模型试验来模拟当土性因动荷作用而发生变化时管道的稳定情况,对这个问题进行了探索,得出了一些规律性的认识,可供海底管道的设计者参考。     

Neutral aldoses as source indicators for marine snow

The chemical characteristics of aggregating material in the marine environment are largely unknown. We investigated neutral aldose (NA) abundance and composition in aggregation of marine snow and other organic matter (OM) size fractions in the field. Four sample sets were fractionated using membrane filtration and ultrafiltration into the following size fractions: particulate material, high-molecular-weight (HMW) material, and low-molecular-weight (LMW) material. We also collected three sample sets of marine-snow aggregates. Each sample set contained small, medium, and large aggregate size fractions and each size fraction consisted of 25–50 aggregates. For 7 marine-snow samples and for each water-sample size fraction, we determined monomeric and polymeric NA concentration, NA yield (amount of NA-C normalized to organic carbon), and composition; total organic carbon (TOC) concentration; transparent exopolymer particles (TEP) concentration, and TEP propensity (TEP concentration after inducing TEP formation in filtered samples). This is the first study to include compound-specific NA determinations on these four marine OM size fractions.The mass balances of organic carbon and NA indicated that there were no serious contamination or loss problems. Concentrations, yields, and NA mol fractions in water samples were similar to results from other studies. Glucose and galactose had the highest relative abundance in all size fractions. The NA yield increased with increasing molecular weight or particle size for all fractions except marine snow. The NA yield increased in the order: LMW< marine snow< HMW< particles. Marine snow had a higher average NA yield than the LMW fraction, but lower than particle and HMW-fractions. This indicates that OM in marine snow could have been diagenetically derived from particulate and HMW-fractions, that is, marine snow may include material from the particulate and the colloidal phase.TEP concentration or TEP propensity was positively correlated with concentrations of all individual NAs as well as the sum NA concentrations, indicating that TEP contains neutral sugars in addition to the acidic polysaccharides stained in the determination of TEP concentrations.Despite the relatively low NA yield in marine snow, marine snow was enriched in NA when compared with seawater, with enrichment factors of 34–225 (average 125). By combining data from this study with data from other studies, we estimate that < 10% of carbohydrates in marine snow comprise NAs.There was no clear correlation between marine-snow aggregate size and NA yield, that is, there appears to be no general age difference between small and large marine-snow aggregates. NA composition was similar among different marine-snow size fracions collected during the same day, indicating that aggregation/disaggregation reactions resulted in homogenizing NA composition in marine-snow aggregates of all sizes. The NA composition of marine snow was different from that of other OM size fractions, indicating either that bacterial degradation has modified the composition of marine snow to a larger extent than other OM size fractions or that marine snow is formed through the aggregation of selected subcomponents of OM.     

Effect of Pollutants on the Physical and Engineering Behavior of Lime-Treated Marine Clay

Rapid industrial growth and increasing population has resulted in the discharge of wastes into the ocean, wastes which ultimately reach the seabed and contaminate the marine sediments. The soil-contaminants interaction, and their associated physico chemical properties with sediments control the behavior of marine clays. Marine clay deposits of low strength and high compressibility are located in many coastal and offshore areas. There are several foundation problems encountered in these weak marine clays. In this study, experimental work was carried out in the laboratory to stabilize soft marine clays using the lime column technique. Also the lime-induced effects on the physical and engineering behavior of marine clays in sulfate-contaminated marine environment was investigated. Consolidation tests indicate that compressibility of the lime-treated samples was reduced to 1/2-1/3 of the virgin soil after 45 days treatment. The test results also suggest that the lime column technique can be conveniently used to improve the behavior of contaminated marine clay deposits.     

Physico-chemical and mineralogical studies on cochin marine clays

Large deposits of marine clays are encountered all along the Indian coastal belt. These clays are pleistocene to recent in origin, are considered to be young, and were deposited in a salt or brackish environment. These clays are very soft in consistency with low in-situ strength and high compressibility. The properties of these soil deposits depend mainly on the clay minerals present. In the present investigation, the mineralogical studies of some Cochin marine clays were carried out using XRD technique. The physical and chemical properties of these deposits were also reported. The test results were compared with some earlier reported works on marine clays.     

南中国海神狐海域天然气水合物上覆地层不排水抗剪强度预测

浅层沉积物不排水抗剪强度（Su）是深水作业的关键参数之一。为了获取南海神狐海域首次海域天然气水合物试采区W18-19框体的基本工程地质特征,试采工程准备阶段开展了原位孔压静力触探测试（CPTU）及大量的室内实验。本文将主要基于CPTU计算不排水抗剪强度的基本模型,采用微型十字板、电动十字板、袖珍贯入仪及不固结不排水三轴实验,确定该区域不排水抗剪强度的基本模式,并提出适用于南海神狐钙质黏土层的不排水抗剪强度纵向分布规律计算模型,对该区域水合物上覆层的不排水抗剪强度进行预测。 结果表明,基于总锥端阻力、有效锥端阻力、超孔隙压力的模型系数分为13.8、4.2、14.4。综合考虑地层压实效应和含气情况,本文提出的分段函数预测模型与室内结果的一致性较好,可用于工程设计阶段进行工区不排水抗剪强度纵向分布规律的预测。另外,基于有效锥端阻力的不排水抗剪强度经验模型适应于浅层极软-较硬压实的钙质粘土层,基于超孔隙压力的不排水抗剪强度模型适用于较硬-坚硬的不含气层,而基于总锥端阻力的不排水抗剪强度计算模型则适用于坚硬含气的钙质黏土层。本文提出的分段函数模型有效的提高了经验模型在南海神狐水合物赋存区的适用性,计算结果可为工程安全评价提供支撑。     

Anisotropic Drained Deformation Behavior and Shear Strength of Natural Soft Marine Clay

The deformation behavior and shear strength of soft marine clays subjected to wave or traffic loads are different from that in triaxial loading due to the changes of major principal stress direction β and intermediate principal stress coefficient b. To investigate the anisotropy affected by β and b in natural soft marine clay, a series of drained tests were conducted by hollow cylinder apparatus. The principal stress direction relative to vertical direction were maintained constant under an increasing shear stress, with fixed intermediate principal stress coefficient b. The influence of the b and β on anisotropy of typically Wenzhou intact clay is discussed. It was found that octahedral stress–strain relationships expressed anisotropy with different b and β. The friction angle and deviator stress ratio with different b and β were presented to provide guidance for engineering projects in the coastal zone.     

Investigation of the stability of submarine sensitive clay slopes underwave-induced pressure

The exploration and exploitation of marine georesources ordinarily disturbs the submarine soft clay surrounding construction areas and leads to a significant decrease in the shear strength of structured and sensitive clayey soils in submarine slopes. Under wave action, local slides can even trigger large-scale submarine landslides, which pose a serious threat to offshore infrastructure such as pipelines and footings. Therefore, accurately evaluating the stability of submarine sensitive clay slopes under wave-induced pressure is one of the core issues of marine geotechnical engineering. In this paper, a kinematic approach of limit analysis combined with strength reduction technique is presented to accurately evaluate the real-time stability of submarine sensitive clay slopes based on the log-spiral failure mechanism, where external work rates produced by wave-induced pressure on slopes are obtained by the numerical integration technique and then are applied to the work-energy balance equations. The mathematical optimization method is employed to achieve the safety factors and the critical sliding surfaces of submarine slopes at different time in a wave cycle. On this basis, the stability of submarine sensitive clay slopes under various wave parameters is systematically investigated. In particular, extreme wave conditions and special cases of slope lengths no more than one wavelength are also discussed. The results indicate that waves have some negative effects on the stability of submarine sensitive clay slopes.     

Strength evaluation of marine clay stabilized by cementitious binder

Abstract

Evaluation of the strength of cement-treated clay with a broad range of mix ratios and curing periods was conducted using unconfined compression tests (UCTs). The influence of cement content, total water content, and curing period on the unconfined compressive strength of cemented clay are investigated. It is found that, at constant total water content, higher cement content results in higher unconfined compressive strength, while the total water content has an opposite effect. A power function can be used to correlate the unconfined compressive strength with the cement content or the total water content. For a fixed mix ratio, the unconfined compressive strength of cement-stabilized clay increases with the curing period, the effect of which can be characterized by a semi-log formula. Also, a strength-prediction model that considers both mix ratios and curing periods for cement-admixed marine clay is developed and validated; the model can capture the effect of clay type by considering the plastic index of untreated soils. It is also proved that the proposed framework for strength development is also applicable for other cement types.