Variability in in situ shear strength of gassy muds

Torque measurements are made by divers with a vane apparatus to a sediment depth of 136 cm in the high-porosity, gassy sediments of Eckernförde Bay. Corrected shear strength values calculated from torque measurements are quite variable in the Eckernförde Bay sediments, varying from less than 0.5 kPa in the top 10 cm of sediment to 4–5 kPa at 136 cm sediment depth. Variability increases markedly below 60 cm sediment depth, probably because of the presence of methane gas bubbles within the sediment fabric.     

Strain-Rate Dependent Stress--Strain Behavior of Undisturbed Hong Kong Marine Deposits under Oedometric and Triaxial Stress States

ABSTRACT

This article presents a testing study on the strain-rate effects on the stress--strain behavior of natural, undisturbed Hong Kong marine deposits (HKMD) from three Hong Kong locations, including a one-dimensional (1-D) compressibility in a confined condition, and undrained shear strengths in triaxial compression and extension modes. The influences of the strain rates on the one-dimensional compressibility are studied by means of constant rate of strain (CRS) tests and multistage loading oedometer (MSL) tests, and those on the undrained shear strengths are studied by K _o-consolidated undrained compression and extension tests with step-changed axial strain rates (CK _oUC and CK _oUE tests), and with both step-changed axial strain rates and relaxation processes (CK _oUCR and CK _oUER tests). The strain-rate effects on the stress--strain behavior are generally examined by “apparent” preconsolidation pressures in the 1-D compressions and undrained shear strengths in the triaxial compression and extension stress states. The stress--strain behavior of the natural, undisturbed HKMD exhibits considerable viscous characteristics. In the CRS and MSL tests at a given strain, the higher the strain rate, the higher the effective stress, the higher the porewater pressure. In the undrained shearing tests, the higher the strain rate, the higher the undrained shear strength, but the lower the porewater pressure. For the CK _oUC and CK _oUE tests on the Tsing Yi site samples, the undrained shear strength increases by 8.5% and 12.1% for one order increment of axial strain rate of 0.2%/hr (i.e., ρ_0.2) for the compression and extension modes respectively. For the CK _oUCR and CK _o tests on the Tung Chung site samples of different compositions, average ρ_0.2 is increased by 6.2% for the compression and 9.5% for the extension, but by 18.8% for the extension on a higher plastic sample. The present study shows that the strain-rate effects on the stress--strain behavior of the undisturbed HKMD are larger for specimens in extension than those in compression.     

南中国海神狐海域天然气水合物上覆地层不排水抗剪强度预测

浅层沉积物不排水抗剪强度（Su）是深水作业的关键参数之一。为了获取南海神狐海域首次海域天然气水合物试采区W18-19框体的基本工程地质特征,试采工程准备阶段开展了原位孔压静力触探测试（CPTU）及大量的室内实验。本文将主要基于CPTU计算不排水抗剪强度的基本模型,采用微型十字板、电动十字板、袖珍贯入仪及不固结不排水三轴实验,确定该区域不排水抗剪强度的基本模式,并提出适用于南海神狐钙质黏土层的不排水抗剪强度纵向分布规律计算模型,对该区域水合物上覆层的不排水抗剪强度进行预测。 结果表明,基于总锥端阻力、有效锥端阻力、超孔隙压力的模型系数分为13.8、4.2、14.4。综合考虑地层压实效应和含气情况,本文提出的分段函数预测模型与室内结果的一致性较好,可用于工程设计阶段进行工区不排水抗剪强度纵向分布规律的预测。另外,基于有效锥端阻力的不排水抗剪强度经验模型适应于浅层极软-较硬压实的钙质粘土层,基于超孔隙压力的不排水抗剪强度模型适用于较硬-坚硬的不含气层,而基于总锥端阻力的不排水抗剪强度计算模型则适用于坚硬含气的钙质黏土层。本文提出的分段函数模型有效的提高了经验模型在南海神狐水合物赋存区的适用性,计算结果可为工程安全评价提供支撑。     

In situ pore‐pressure measurement in Mississippi delta front sediments

Abstract

A differential piezometer was used to monitor excess pore pressure in the soft clayey seafloor sediments of Block 28, South Pass, Mississippi delta, from September 1975 to March 1976. An ambient excess pore pressure of about 32 kPa was measured at a depth of 6.4 m below the mudline in a water depth of 19 m. Storm‐wave‐generated cyclic fluctuations of ± 4 kPa about the ambient were measured during Hurricane Eloise. Irregular, long‐period, small‐amplitude fluctuations in excess pore pressures persisted for 4 days following the storm. An effective stress analysis was made by using excess pore pressures; in situ field vane‐shear strength, t _fv, measurements; and laboratory wet unit weights measured by Lehigh and NOAA. The effective stress of the SEA‐SWAB site soil was calculated to be zero to a depth of about 6 m, below which it increased to 3.5 kPa at a depth of 15 m. Values of c´ = 4.6 kPa, ?´ = 56°, and T _FV/σ_vo(c/p) =0.1–0.2 were calculated, and it was concluded that these data do not represent the in situ condition of the soil because of the probability that the measured soil properties were affected by the presence of gas. However, it is clear that the soil is significantly underconsolidated.     

Estimation of Residual Undrained Shear Strength from Gravity Corer Penetration Data

Residual undrained shear strength, s _{u_res} , is an important parameter for analyzing the response of structures buried within potentially unstable soil mass. A framework for estimating s _{u_res} of fine grained sediments from gravity corer penetration has been developed considering viscous drag during free fall of the corer through seawater and cohesive energy loss during sediment penetration. The procedure was used to estimate s _{u_res} using data from a submarine geotechnical investigation in western Canada. Comparison of the results with alternative estimates of s _{u_res} from miniature torvane tests on the gravity core samples and CPTs performed nearby reveals a reasonable agreement.     

Evaluation of the Strength Increase of Marine Clay under Staged Embankment Loading: A Case Study

This article presents a case history of the performance of a full-scale test embankment constructed on a marine soft clay deposit improved by prefabricated vertical drains (PVDs) in the east of China. For analyzing the subsoil behavior, a 2D FEM model is established, in which the PVD-improved effect is considered by a simplified method of equivalent vertical hydraulic conductivity. The calculated results can predict the settlement behavior well; however, the FEM gives an underestimate for the value of excess pore pressures and it predicts similar values for the dissipation rate of excess pore pressures. The measured undrained shear strength of subsoil, C_u, is compared with the predicted value based on Ladd’s empirical equation and the Modified Cam-Clay model (MCC). The shear strength predicted by Ladd’s equation agrees well with the measured value, whereas the MCC overestimates the ability to improve subsoil shear strength during consolidation. The undrained shear strength of subsoil, C_u, increased as the construction progressed, and the shear strength incremental ratio, ΔC_u/Δp′, decreased slightly with the degree of consolidation, U.     

Field Evaluation of Undrained Shear Strength from Piezocone Penetration Tests in Soft Marine Clay

The use of the piezocone penetration test (CPTU) in a geotechnical site investigation offers direct field measurement on stratigraphy and soil behavior. Compared with some traditional investigation methods, such as drilling, sampling and field inspecting method or laboratory test procedures, CPTU can greatly accelerate the field work and hereby reduce corresponding operation cost. The undrained shear strength is a key parameter in estimation of the stability of natural slopes and deformation of embankments in soft clays. This paper provides the measurements of in situ CPTU, field vane testing and laboratory undrained triaxial testing of Lianyungang marine clay in Jiangsu province of China. Based on the literature review of previous interpretation methods, this paper presents a comparison of field vane testing measurements to CPTU interpretation results. The undrained shear strength values from both the field vane tests and cone penetration resistances are lowest at the mid-depths of the marine clay layers, and the excess pore water pressures are highest at the mid-depths of the marine clay layers, indicating that the marine clay layer is underconsolidated.     

Vertical Variability of the Undrained Shear Strength of Golden Horn Clay

In this study, a stochastic method was applied to investigate if there exists a statistical correlation between values of undrained shear strength at various vertical distances along Golden Horn. Therefore, the undrained shear strength values measured by field vane shear tests at different depths were used to determine the depth dependent variation of the mean value and standard deviation. Futhermore, autocorrelation functions were defined to describe the correlation between values of c_u at different depths. The study showed that the applied method might provide a statistical range to estimate the undrained shear strength value at depths where no measurements are undertaken.     

Correlations between CPT and FVT Results for Busan Clay

In this study, CPT and FVT tests are carried out on young, normally consolidated clay (Busan clay, which is an unusually thick deposit) at several locations in the Nakdong River deltaic plane in Busan, Korea. Two correlation techniques are applied for estimating the cone factors for which the uncorrected and corrected field vane strengths are used as the reference strength. First, due to the scattered data over the entire depth, a direct correlation between the tested results (a method generally used in practice), is applied for each depositional environment (facies) that is detected from the CPT profiles and the geological analysis. Secondly, a special attempt is made to determine the cone factors based on the fact that the ratios of the field vane strength and the (q _t  ? σ _v0) and (u ₂ ? u ₀) values to the effective overburden pressure respectively, are approximately constant for each facies (the indirect correlation). It appears that the values obtained from the two techniques are almost identical. However, the direct correlation is sensitively affected by the fabric effects especially in some of the uppermost and lowermost layers of the clay and hence the arithmetic average values of each facies sometimes result in lower correlation coefficients. It is therefore inferred that the indirect correlation is more proficient for estimating the cone factors at each facies and can be used for practical applications. From the results of the indirect correlation, the cone factors of Busan clay are N _kt  = 7.13–13.06, N _kt,corr  = 9.45–17.07, N _Δu  = 6.10–9.88 and N _Δu,corr  = 8.41–12.24, the corrected values of which are considerably smaller or larger than the general ranges recommended by Lunne et al. (1997a). However, good correlations between N _kt and I _P , and between N _Δu (or N _kt ) and B _q , are not found for the clay.     

San Diego trough geotechnical test area

Abstract

The San Diego Trough Geotechnical Test Area, located about 24 km southwest of San Diego in a water depth of about 1.2 km, lies near the base of the Coronado Escarpment directly north of the Coronado Fan. A new bathymetric map delineates a shallow basin in the soft, highly plastic, clayey silts flooring the Test Area. Measurements of shear strength by vane and static cone pene‐trometer, and bulk density by nuclear densitometer, were made in place from the submersible Deep Quest. Sixteen short (< 1.6 m) gravity cores were collected from ships.

The geotechnical properties show little areal variation and generally change uniformly with depth within the 55 km² Test Area. Silt is the predominant grain size, averaging about 62%. In‐place bulk density shows little change with increasing depth, values range from 1.23 to 1.26 Mg/m³; laboratory density values increase with depth, ranging from 1.30 to 1.52 Mg/m³ between the surface and a depth of about 1.1 m. The difference between the in place and laboratory values may indicate sampling densification of the cored sediment. Water content in the cores decreases uniformly within the range of 249 to 43% dry weight. Shear strength increases linearly with depth. The laboratory shear strength values are lower than the in place values, which range from 4 kPa at the surface to about 29 kPa at a depth of 3.27 m. Predictor equations relate Atterberg limits, bulk density, water content, and laboratory and in place shear strength to depth. Sedimentation‐compression e log p curves have an equivalent compression index of 1.5 to nearly 2. Excluding rurbidite layers and sampling disturbance effects, all cores indicate a uniform depositional environment in the surface to 1.6 m of sediment sampled. The geotechnical properties indicate that the sediments in the west central and southwest parts of the Test Area exhibit vertical heterogeneity due to thin silt‐sand layers, presumably of turbidity current origin, that originated from the Coronado Canyon.     

A novel shear vane used to determine the evolution of hydraulic dredge tracks in sub-tidal marine sediments

A novel shear vane is described which can be used to record the shear strength of discrete depth horizons of a variety of marine sediment types in situ. This vane, or modifications of it, has great potential in allowing measurement of in situ shear strength without requiring any samples to be removed from the sea bed, a process which can often destroy the fine structure of the sediment. The vane was used to monitor the change in sediment shear strength caused by a hydraulic dredge, which was used to fish razor clams (Ensis arcuatus) in a sheltered bay within the Clyde Sea area, Scotland. Data collected using this apparatus provided valuable and immediate information on the stratification of the sea bed post-dredging and allowed the evolution of the dredge track to be regularly monitored by divers over a period of 100 d.     

A method for correcting the temperature effect on uCPT measurements in seabed sediments

Abstract

The zero load readings of cone resistance (q_c) and sleeve friction (f_s) measured by a piezocone (uCPT) shift with the ambient temperature. A method of correcting the effect of temperature on uCPT measurements in seabed sediments has been proposed for the case where there is no temperature sensor in the uCPT probe. This method is based on the assumption that the “actual” profile of f_s of soft shallow seabed sediments linearly increases with depth, and a rate of increase of α?=?0.2?kPa/m was obtained using measured ground temperatures and f_s values in seabed sediments in Isahaya Bay, Japan. An “actual” f_s profile can then be constructed using the measured f_s value at the shallow surface and the value of α. Using the differences between the measured and the estimated “actual” f_s profiles, the ground temperature profile can be obtained, and then the effect of temperature on the uCPT measurements can be corrected. The proposed method was used for temperature corrections on uCPT measurements in Isahaya Bay, Japan. The values of undrained shear strength (s_u) from the temperature-corrected uCPT measurements agree well with the laboratory measured values of s_u using the undisturbed soil samples.     

In situ tensile fracture toughness of surficial cohesive marine sediments

This study reports the first in situ measurements of tensile fracture toughness, K _IC, of soft, surficial, cohesive marine sediments. A newly developed probe continuously measures the stress required to cause tensile failure in sediments to depths of up to 1 m. Probe measurements are in agreement with standard laboratory methods of K _IC measurements in both potter’s clay and natural sediments. The data comprise in situ depth profiles from three field sites in Nova Scotia, Canada. Measured K _IC at two muddy sites (median grain size of 23–50 μm) range from near zero at the sediment surface to >1,800 Pa m^1/2 at 0.2 m depth. These profiles also appear to identify the bioturbated/mixed depth. K _IC for a sandy site (>90% sand) is an order of magnitude lower than for the muddy sediments, and reflects the lack of cohesion/adhesion. A comparison of K _IC, median grain size, and porosity in muddy sediments indicates that consolidation increases fracture strength, whereas inclusion of sand causes weakening; thus, sand-bearing layers can be easily identified in K _IC profiles. K _IC and vane-measured shear strength correlate strongly, which suggests that the vane measurements should perhaps be interpreted as shear fracture toughness, rather than shear strength. Comparison of in situ probe-measured values with K _IC of soils and gelatin shows that sediments have a K _IC range intermediate between denser compacted soils and softer, elastic gelatin.     

In situ pore-pressure evolution during dynamic CPT measurements in soft sediments of the western Baltic Sea

We present in situ strength and pore-pressure measurements from 57 dynamic cone penetration tests in sediments of Mecklenburg (n?=?51), Eckernförde (n?=?2) and Gelting (n?=?4) bays, western Baltic Sea, characterised by thick mud layers and partially free microbial gas resulting from the degradation of organic material. In Mecklenburg and Eckernförde bays, sediment sampling by nine gravity cores served sedimentological characterisation, analyses of geotechnical properties, and laboratory shear tests. At selected localities, high-resolution echo-sounder profiles were acquired. Our aim was to deploy a dynamic cone penetrometer (CPT) to infer sediment shear strength and cohesion of the sea bottom as a function of fluid saturation. The results show very variable changes in pore pressure and sediment strength during the CPT deployments. The majority of the CPT measurements (n?=?54) show initially negative pore-pressure values during penetration, and a delayed response towards positive pressures thereafter. This so-called type B pore-pressure signal was recorded in all three bays, and is typically found in soft muds with high water contents and undrained shear strengths of 1.6–6.4 kPa. The type B signal is further affected by displacement of sediment and fluid upon penetration of the lance, skin effects during dynamic profiling, enhanced consolidation and strength of individual horizons, the presence of free gas, and a dilatory response of the sediment. In Mecklenburg Bay, the remaining small number of CPT measurements (n?=?3) show a well-defined peak in both pore pressure and cone resistance during penetration, i.e. an initial marked increase which is followed by exponential pore-pressure decay during dissipation. This so-called type A pore-pressure signal is associated with normally consolidated mud, with indurated clay layers showing significantly higher undrained shear strength (up to 19 kPa). In Eckernförde and Gelting bays pore-pressure response type B is exclusively found, while in Mecklenburg Bay types A and B were detected. Despite the striking similarities in incremental density increase and shear strength behaviour with depth, gas occurrence and subtle variations in the coarse-grained fraction cause distinct pore-pressure curves. Gaseous muds interbedded with silty and sandy layers are most common in the three bays, and the potential effect of free gas (i.e. undersaturated pore space) on in situ strength has to be explored further.     

Behavior of Loose Silty Sand of Chlef River: Effect of Low Plastic Fine Contents and Other Parameters

This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density D_r = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (F_c), inter-granular void ratio (e_g), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (q_peak) and the logarithm of the saturated hydraulic conductivity (k_sat) for all confining pressures.     

Distribution of Overturn Induced by Internal Tides and Thorpe Scale in Uchiura Bay

The vertical mixing process induced by internal tides was investigated by repeated conductivity, temperature, and depth (CTD) measurements and bottom-mounted acoustic Doppler current profiler (ADCP) in Uchiura Bay from July 24 to 25, 2001. Internal tides were observed with a wave height of 40 m and a horizontal current of 0.3 ms⁻¹. Density inversions were found in the CTD data, and the method of Galbraith and Kelley (1996) was applied to the data to identify overturns and to calculate Thorpe scale. Most of the overturns distributed in the region of low Richardson number, so that they were considered to be caused by shear instability associated with the internal tides. Thorpe scale was calculated to be 0.48 m. From the Thorpe scale, the vertical eddy diffusivity due to internal tides in Uchiura Bay was estimated as K _ρ ∼ 10⁻⁴ m²s⁻¹. This revised version was published online in July 2006 with corrections to the Cover Date.     

Analysis of submarine slumping in the continental slope off the southern coast of Israel

Abstract

The continental slope off the coast of Israel is riddled with numerous large slump scars at depths greater than 400 m. Recent scar slumps are situated in the steepest central portions of the continental slope (400–450 m depth, α=6°), frequently disfiguring older slump scars in its lower portions. The slumping materials were probably largely transported downslope in the form of density currents, and occasionally by sliding of large sediment chunks. Upslope retrogressive slumping phases progressively disfigure the shape of the slump scars until they totally disappear, causing net reduction of the thickness of the sedimentary column. To provide a basis for the quantitative analysis of slumping, laboratory vane tests, triaxial consolidated, undrained compression tests with pore‐pressure measurements, drained direct shear tests, and consolidation tests were performed oh undisturbed samples. Because the sediments consist of normally consolidated silty clays, the geotechnical properties measured on the core samples can be readily extrapolated for greater depths, assuming the sediments are homogeneous. Angles of internal friction measured by direct shearing under drained conditions are ?_d =24°‐25°, designating the maximum possible angle of a stable infinite slope. These angles are appreciably higher than the steepest slopes in the investigated area, and a drained slumping mechanism is therefore considered unlikely. The slopes of the slump scar walls are about 20°; therefore, in the absence of active erosional, sedimentological, or tectonic agents, these walls have long‐term stability (drained shear). Undrained shear failure resulting in slope instability may be attributable to rapid changes in slope geometry (undercutting or oversteepening of the slope), fluctuations in pore pressure, or accelerations associated with earthquakes. Undrained shear‐strength parameters were determined by both laboratory consolidated‐un‐drained triaxial tests and by miniature vane shear tests. The angles of internal friction that were measured are ?_cu =15°‐17°, and the c_u/p_o values range between 0.22 and 0.75. An analysis of the force equilibrium within the sediments leads to the conclusion that horizontal earthquake‐induced accelerations, as little as 5–6% of gravity, are sufficient to cause slope failure in the steepest slope zone (400–450 m depth, α = 6°, c_u /p_o =0.25). Collapse resulting from liquefaction is unlikely, as the sediments are normally consolidated silty clays with intermediate sensitivity, S_t =2–4.

The existence of slump scars in the lower portion of the continental slope, characterized by gentle slopes (α=1°‐3°) and sediments with high shear strength (c _u /p _o=0.30–0.50) is attributed to large horizontal accelerations(k=12–16% of gravity). Owing to the wide range of geotechnical properties of the sediments (c_u /p_o = 0.20–0.75) and the inclination of the continental slope (α=1°‐6°), the same earthquake may generate a wide range of horizontal accelerations in different portions of the continental slope, and slumping may occur wherever the stability equilibrium is disrupted.     

Analysis of submarine slumping in the continental slope off the southern coast of Israel

Abstract

The continental slope off the coast of Israel is riddled with numerous large slump scars at depths greater than 400 m. Recent scar slumps are situated in the steepest central portions of the continental slope (400–450 m depth, α = 6°), frequently disfiguring older slump scars in its lower portions. The slumping materials were probably largely transported downslope in the form of density currents, and occasionally by sliding of large sediment chunks. Upslope retrogressive slumping phases progressively disfigure the shape of the slump scars until they totally disappear, causing net reduction of the thickness of the sedimentary column. To provide a basis for the quantitative analysis of slumping, laboratory vane tests, triaxial consolidated, undrained compression tests with pore‐pressure measurements, drained direct shear tests, and consolidation tests were performed oh undisturbed samples. Because the sediments consist of normally consolidated silty clays, the geotechnical properties measured on the core samples can be readily extrapolated for greater depths, assuming the sediments are homogeneous. Angles of internal friction measured by direct shearing under drained conditions are ?_d =24°‐25°, designating the maximum possible angle of a stable infinite slope. These angles are appreciably higher than the steepest slopes in the investigated area, and a drained slumping mechanism is therefore considered unlikely. The slopes of the slump scar walls are about 20°; therefore, in the absence of active erosional, sedimentological, or tectonic agents, these walls have long‐term stability (drained shear). Undrained shear failure resulting in slope instability may be attributable to rapid changes in slope geometry (undercutting or oversteepening of the slope), fluctuations in pore pressure, or accelerations associated with earthquakes. Undrained shear‐strength parameters were determined by both laboratory consolidated‐un‐ drained triaxial tests and by miniature vane shear tests. The angles of internal friction that were measured are ?_cu =15°‐17°, and the c_u/p _o values range between 0.22 and 0.75. An analysis of the force equilibrium within the sediments leads to the conclusion that horizontal earthquake‐induced accelerations, as little as 5–6% of gravity, are sufficient to cause slope failure in the steepest slope zone (400–450 m depth, α=6°, c_u/p _o=0.25). Collapse resulting from liquefaction is unlikely, as the sediments are normally consolidated silty clays with intermediate sensitivity, S_t =2–4.

The existence of slump scars in the lower portion of the continental slope, characterized by gentle slopes (α=1°‐3°) and sediments with high shear strength (c_u/p _o=0.30–0.50) is attributed to large horizontal accelerations (k= 12–16% of gravity). Owing to the wide range of geotechnical properties of the sediments (c_u/p _o= 0.20–0.75) and the inclination of the continental slope (α=1°‐6°), the same earthquake may generate a wide range of horizontal accelerations in different portions of the continental slope, and slumping may occur wherever the stability equilibrium is disrupted.     

Geotechnical Investigations at the Dalian Offshore Airport,China

Based on the geotechnical investigation data of artificial island at Dalian Offshore Airport, the spatial distribution of the physical and mechanical properties of deposit soils was statistically analyzed. The field investigation revealed that the deposit soils could be subdivided into three strata, i.e., the top marine deposit stratum, middle marine-continental deposit stratum, and deep continental deposit stratum. Field and laboratory test results demonstrated that the marine deposit soils had high water content (31.2% < w_n < 63.10%), large void ratio (0.88 < e₀ < 1.75), low permeability (k_v < 10^?6 cm/s), flow-plastic state (I_L > 1), under consolidated (OCR < 1), high compressibility (E_s < 4 MPa), low shear strength (11.7 kPa < c_u < 43.7 kPa), and low bearing capacity (0 < f_ak < 120 kPa), they could not be used as natural foundation. The marine-continental and continental deposits were normally consolidated to over-consolidated (OCR ≥ 1), medium compressibility (4 MPa < E_s < 20 MPa), high shear strength (29.7 kPa < c_u < 73.7 kPa), and high bearing capacity (f_ak > 120 kPa). In addition, regression analysis results showed that the compression ratio was positively correlated with the natural water content, the coefficient of vertical consolidation was negatively correlated with the plasticity index, and the coefficient of vertical permeability was positively correlated with the initial void ratio. The results of the field and laboratory tests were synthesized to provide a basis for reclamation design.     

Geology and geotechnical characteristics of sediments in east bay area,Mississippi delta

Abstract

Deltaic sedimentation has produced an accumulation of clay and silt with a maximum thickness of 90 m in East Bay area. Sediments in the upper 50 m grade from interbedded sand, silt, and clay near South Pass and Southwest Pass to predominantly clay in the central part of the area. The variation in the types of sediments and rates of deposition greatly affected the engineering properties of these deposits. Sediments from boreholes in the central part of the area have shear strengths of less than 10 kPa to a depth of at least 50 m. Near the distributaries, shear strength increases with depth; values as high as 43 kPa were measured in sediments in the upper 50 m. These sediments are generally stronger and coarser, and have a lower water content and liquid limit than do sediments at comparable depths in the central part of the area.