Geotechnical Properties of Surface Sediments in the INDEX Area

As a part of the environmental impact assessment studies, geotechnical properties of sediments were determined in the Central Indian Basin. The undrained shear strength and index properties of the siliceous sediments were determined on 20 box cores of uniform dimension collected from various locations in five preselected sites. The maximum core length encountered was 41 cm and most of the sediments were siliceous oozes consisting of radiolarian or diatomaceous tests. The shear strength measurements revealed that surface sediments deposited in recent times (0-10 cm) have a shear strength of 0-1 kPa; this value increases with depth, reaching 10 kPa at 40 cm deep. Older sediments have greater strength because of compaction. Water content varies in the wide range of 312-577% and decreases with depth. The clay minerals such as smectite and illite are dominant and show some control over water content. Wet density, specific gravity, and porosity do not indicate any notable variation with depth, thereby indicating a uniform, slow rate of sedimentation. The average porosity of sediments is 90.2%, specific gravity 2.18, and wet bulk density 1.12 g/cm 3 . Sediments exhibit medium to high plasticity characteristics, with the average plasticity index varying between 105% and 136%. Preliminary studies on postdisturbance samples showed an increase in natural water content and a decrease in undrained shear strength of sediments in the top 10- to 15-cm layer.     

南海中沙天然气水合物资源远景区海底沉积物的物理力学性质研究

根据南海中沙天然气水合物远景区沉积物样品的分析资料,从物理力学特征各方面对本区海底沉积物进行了综合工程地质特征研究。结果表明,本区海底沉积物类型全部为淤泥,工程地质性质相近,以高含水率、高孔隙比、低密度及高塑性为主要特征,抗剪强度很小,压缩系数均大于0.5。土体沉积环境为水动力强度较弱的深海半深海环境。     

Geotechnical Properties of Surface Sediments in the INDEX Area

Abstract

As a part of the environmental impact assessment studies, geotechnical properties of sediments were determined in the Central Indian Basin. The undrained shear strength and index properties of the siliceous sediments were determined on 20 box cores of uniform dimension collected from various locations in five preselected sites. The maximum core length encountered was 41 cm and most of the sediments were siliceous oozes consisting of radiolarian or diatomaceous tests. The shear strength measurements revealed that surface sediments deposited in recent times (0–10 cm) have a shear strength of 0–1 kPa; this value increases with depth, reaching 10 kPa at 40 cm deep. Older sediments have greater strength because of compaction. Water content varies in the wide range of 312–577% and decreases with depth. The clay minerals such as smectite and illite are dominant and show some control over water content. Wet density, specific gravity, and porosity do not indicate any notable variation with depth, thereby indicating a uniform, slow rate of sedimentation. The average porosity of sediments is 90.2%, specific gravity 2.18, and wet bulk density 1.12 g/cm³. Sediments exhibit medium to high plasticity characteristics, with the average plasticity index varying between 105% and 136%. Preliminary studies on postdisturbance samples showed an increase in natural water content and a decrease in undrained shear strength of sediments in the top 10- to 15-cm layer.     

The Effects of Microstructure on Shear Properties of Shallow Marine Sediments

This study was undertaken to investigate the implication of geoacoustic behaviors in the shallow marine sediments associated with the changes in geotechnical index properties. Two piston cores (270 cm and 400 cm in core length) used in this study were recovered from stations 1 and 2, the western continental margin, the East Sea. Scanning electron microscopy (SEM) was employed to illustrate the effects of microstructure on shear properties. The direct SEM observation of sediment fabrics is inevitable to understand the correlation of the changes in geoacoustic properties to the sediment structure. The consolidation of sediments by overburden stress resulting in the clay fabric alteration appears to play an important role in changing shear properties. Water contents and porosity of sediments gradually decreases with increasing depth, whereas wet bulk density shows a reverse trend. It is interesting to note that shear wave velocities increase rapidly from 8 to 20 m/s while compressional wave velocities significantly fluctuate, ranging from 1450 to 1550 m/s with depth. The fabric changes in sediment with increasing depth for example, uniform grain size and well oriented clay fabrics may cause the shear strength increase from 1 to 12 kPa. Shear wave velocity is, therefore, shown to be very sensitive to the changes in undrained strength for unconsolidated marine sediments. This correlation allows an in-situ estimation of shear stress in the subsurface from shear wave velocity data.     

Geotechnical characteristics of mississippi delta sediments,southeast Louisiana

An investigation of the geotechnical properties of sediments from 57 boreholes drilled in West Delta and South Pass OSC Lease Areas, offshore Louisiana, indicated that sediment texture, shear strength, water content, and liquid limit vary significantly laterally and with depth. Samples are predominantly soft, fine‐grained sediments with high water content and medium to high plasticity. Firm, coarser‐grained sediments were obtained near the shoreline in South Pass OCS Lease Area and in the northern and eastern parts of West Delta OCS Lease Area. Trends in the distribution of geotechnical properties appear to be influenced by sediment texture and rate of sedimentation.     

San Diego trough geotechnical test area

Abstract

The San Diego Trough Geotechnical Test Area, located about 24 km southwest of San Diego in a water depth of about 1.2 km, lies near the base of the Coronado Escarpment directly north of the Coronado Fan. A new bathymetric map delineates a shallow basin in the soft, highly plastic, clayey silts flooring the Test Area. Measurements of shear strength by vane and static cone pene‐trometer, and bulk density by nuclear densitometer, were made in place from the submersible Deep Quest. Sixteen short (< 1.6 m) gravity cores were collected from ships.

The geotechnical properties show little areal variation and generally change uniformly with depth within the 55 km² Test Area. Silt is the predominant grain size, averaging about 62%. In‐place bulk density shows little change with increasing depth, values range from 1.23 to 1.26 Mg/m³; laboratory density values increase with depth, ranging from 1.30 to 1.52 Mg/m³ between the surface and a depth of about 1.1 m. The difference between the in place and laboratory values may indicate sampling densification of the cored sediment. Water content in the cores decreases uniformly within the range of 249 to 43% dry weight. Shear strength increases linearly with depth. The laboratory shear strength values are lower than the in place values, which range from 4 kPa at the surface to about 29 kPa at a depth of 3.27 m. Predictor equations relate Atterberg limits, bulk density, water content, and laboratory and in place shear strength to depth. Sedimentation‐compression e log p curves have an equivalent compression index of 1.5 to nearly 2. Excluding rurbidite layers and sampling disturbance effects, all cores indicate a uniform depositional environment in the surface to 1.6 m of sediment sampled. The geotechnical properties indicate that the sediments in the west central and southwest parts of the Test Area exhibit vertical heterogeneity due to thin silt‐sand layers, presumably of turbidity current origin, that originated from the Coronado Canyon.     

东海油气资源区海底沉积物的工程地质特征

根据“灾害地质环境调查与评价”项目1995年11月、1996年6月和1998年10月的航次调查及随后的沉积物样品的试验室分析资料，从物理性质和力学特征各方面对东海油气资源区海底沉积物进行了综合工程地质特征研究。发现本区沉积物结构、剪切特征、含水量和液塑限随深度的变化而变化；本区海底沉积物类型既分布有中砂、细砂和粉砂3种砂性土，也分布有淤泥、淤泥质粘土和粘质粉土3种粘性土，沉积物的物理力学性质与相应的土类变化相一致。     

Mississippi prodelta crusts: A clay fabric and geotechnical analysis

Abstract

"Crust”; zones, as defined by shear strength profiles, have been delineated in Mississippi prodelta sediments since the advent of the remote wire‐line probe. Attempts to map the distribution of the “crust”; on the prodelta have been hampered by sparsity of in situ measurements and its apparent lateral discontinuity. Evidence based on clay fabric, geotechnical properties, and the location of selected cores within certain geomorphic zones, suggests the “crusts”; are associated with zones of shearing during an episode of submarine sediment movement on the prodelta.

The clay fabric within the “crust”; zone differs from that found above and below in the high‐porosity sediments. A noticeable degree of clay platelet preferential alignment is characteristic of sediments within the “crust.”; This preferred orientation occurs as localizations rather than as an overall alignment of all the particles. The clay fabric of the higher‐porosity sediments above and below the “crust”; is typified by randomly arranged clay particles and domains, sharing edge‐to‐face contacts which create an open framework. Apparent increases in the coarse silt fraction in the “crust”; zone were observed initially in scanning electron and transmission electron micrographs and later confirmed by grain size analysis. The presence of this silt apparently contributes to the increase in shear strength within the “crust.”; Clay particle arrangement in close proximity to these larger grains is modified in such a manner as to reduce water contents. Transmission electron microscopy and scanning electron microscopy observations of the “crust”; reveal that the void ratio decreases, resulting in a concomitant reduction in the water content as reflected in the geotechnical properties profiles. The type of fabric exhibited by the “crust”; suggests a remolding and dewatering of initially porous silty clay sediments in response to shear stresses operating on the prodelta.

Core samples were recovered from sediments exhibiting a “crust”; in areas identified by other researchers as unstable, based on seismic and acoustic profiles and sidescan sonar records. The prodelta has been modified by a peripheral mudflow at the location where the cores were collected for this study.     

闽浙沿岸沉积物的工程地质特性及其成因简析

根据闽浙沿岸沉积物的实验室分析资料,从物理性质和力学特征对海底沉积物的综合工程地质特征进行了研究,结果发现,本区沉积物以淤泥和淤泥质黏土为主,含少量细砂、粉砂、黏土和粉质黏土等,总的表现为含水率高、孔隙比大、压缩性强、塑性大和强度低。从微观结构、物质来源、物质成分、水动力条件等方面对沉积物的工程特性进行了成因分析,这些因素是造成本区沉积物工程性质不良的主要原因。     

In Memoriam

Abstract

The engineering properties of deep continental margin sediments were determined on a worldwide basis. Deep Sea Drilling Project (DSDP) core data and material were utilized from over 900 cores obtained from 89 sites, primarily on the continental margins. Cores were recovered from penetrations to 200 m in water depths averaging 3000 m. Supplementary laboratory testing on selected cores was directed toward determining index properties and shear strength properties of the sediments. The study included a literature review of deep‐sea soil properties, the results of which are to be used by DSDP to evaluate foundation conditions for reentry cones with long casing strings. The results will also be used for a feasibility study of an ultradeepwater marine riser and well‐control system. The marine sediments examined can be divided into three main types: clay, calcareous ooze, and siliceous ooze. Sediment distribution consisted of 48% calcareous ooze, 43% clay, 6% siliceous ooze, and 3% volcanic ash. Because of the sample disturbance inherent in the deepwater coring operation, emphasis was placed on analyzing sediment properties not significantly affected by changes in in situ stresses and structure caused by sampling. Averages and ranges in values of water content and unit weight are presented for the three main sediment types. Plasticity and strength characteristics are discussed in detail and the elastic and compression properties are outlined. The geotechnical properties of deep continental margin soils are summarized.     

Shear Strength Development with Burial in Eel River Margin Slope Sediments

As part of the STRATAFORM project, a series of cores were obtained from the Eel River Margin area of Eureka, California. The geotechnical analysis of intact specimens and of reconstituted samples provides some insight on the development of shear strength with burial. The results show the effect of bioturbation in the early part of the lifetime of a sediment. SEDCON tests were used to proposed various relationships which help predict the changes in density, liquidity index, and strength as a function of depth. These relationships are found useful from near the water sediment-interface down to a depth of at least 400 m in the sediment column.     

Shear Strength Development with Burial in Eel River Margin Slope Sediments

As part of the STRATAFORM project, a series of cores were obtained from the Eel River Margin area of Eureka, California. The geotechnical analysis of intact specimens and of reconstituted samples provides some insight on the development of shear strength with burial. The results show the effect of bioturbation in the early part of the lifetime of a sediment. SEDCON tests were used to proposed various relationships which help predict the changes in density, liquidity index, and strength as a function of depth. These relationships are found useful from near the water sediment-interface down to a depth of at least 400 m in the sediment column.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Geotechnical properties of deep oceanic sediments recovered from the hydrate occurrence regions in the Ulleung Basin, East Sea, offshore Korea

This study presents comprehensive geotechnical data of the natural marine sediments cored from the hydrate occurrence regions during the Ulleung Basin Gas Hydrate Expedition 1 (UBGH1), East Sea, offshore Korea in 2007. Geotechnical soil index properties of the Ulleung Basin sediments, including grain size distribution, porosity, water content, Atterberg limits, specific gravity, and specific surface area, were experimentally determined. These soil index properties were correlated to geotechnical engineering parameters (e.g., shear strength and friction angle) by using well-known empirical relationships. By performing standard consolidation tests on both undisturbed specimens (as recovered from the original core liner after hydrate dissociation) and remolded specimens, stress-dependent mechanical and hydraulic properties (e.g., compressibility and hydraulic conductivity) were measured. The experimental results provide important engineering parameters, and demonstrate the effect of hydrate presence and consequential dissociation to index properties, engineering parameters, and innate sediment structures.     

Variability in Particle Mixing Rates in Sediments with Polymetallic Nodules in the Equatorial Eastern Pacific as Determined from Measurements of Excess <Superscript>210</Superscript>Pb

Radionuclide activities of ²¹⁰Pb and ²²⁶Ra were measured to determine bioturbation coefficients (D_b) in seven sediment cores from the Korean licensed block for polymetallic nodules in the Clarion–Clipperton Fracture Zone. Variability in D_b is considered in the context of the sedimentological, geochemical, and geotechnical properties of the sediments. D_b values in the studied cores were estimated using a steady-state diffusion model and varied over a wide range from 1.1 to 293 cm²/yr with corresponding mixing depths (L) of 26 to 144 cm. When excepting for spurious results obtained from cores where diffusive mixing does not apply, D_b values range from 1.1 to 9.0 cm²/yr with corresponding mixing depths (L) of 26 to 63 cm. Such wide variability in D_b and L values is exceptional in sites with water depths of ～5000 m and is attributed in this study to an uneven distribution of sediment layers with different shear strengths and total organic carbon (TOC) contents, caused by erosion events. The studied cores can be grouped into two categories based on lithologic associations: layers with high maximum shear strength (MSS) and low TOC content, showing a narrow range of D_b values (1.1–9.0 cm²/yr); and layers with low MSS and high TOC content, yielding much higher D_b values of over 30 cm²/yr. The distribution of different lithologies, and the resultant spatial variability in MSS and labile organic matter content, controls the presence and maximum burrowing depth of infauna by affecting their mobility and the availability of food. This study provides a unique case showing that shear strength, which relates to the degree of sediment consolidation, might be an important factor in controlling rates of bioturbation and sediment mixing depths.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Abstract

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m^?2 day^?1. Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (～4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ～5 days showed a reduction in particle fluxes of ～50%, indicating rapid particle settlement.     

Sound velocity and related properties of seafloor sediments in the Bering Sea and Chukchi Sea

The Bering Sea shelf and Chukchi Sea shelf are believed to hold enormous oil and gas reserves which have attracted a lot of geophysical surveys. For the interpretation of acoustic geophysical survey results, sediment sound velocity is one of the main parameters. On seven sediment cores collected from the Bering Sea and Chukchi Sea during the 5th Chinese National Arctic Research Expedition, sound velocity measurements were made at 35, 50, 100, 135, 150, 174, 200, and 250 k Hz using eight separate pairs of ultrasonic transducers. The measured sound velocities range from 1 425.1 m/s to 1 606.4 m/s and are dispersive with the degrees of dispersion from 2.2% to 4.0% over a frequency range of 35–250 k Hz. After the sound velocity measurements, the measurements of selected geotechnical properties and the Scanning Electron Microscopic observation of microstructure were also made on the sediment cores. The results show that the seafloor sediments are composed of silty sand, sandy silt, coarse silt, clayey silt, sand-silt-clay and silty clay. Aggregate and diatom debris is found in the seafloor sediments. Through comparative analysis of microphotographs and geotechnical properties, it is assumed that the large pore spaces between aggregates and the intraparticulate porosity of diatom debris increase the porosity of the seafloor sediments, and affect other geotechnical properties. The correlation analysis of sound velocity and geotechnical properties shows that the correlation of sound velocity with porosity and wet bulk density is extreme significant, while the correlation of sound velocity with clay content, mean grain size and organic content is not significant. The regression equations between porosity, wet bulk density and sound velocity based on best-fit polynomial are given.     

In situ pore-pressure evolution during dynamic CPT measurements in soft sediments of the western Baltic Sea

We present in situ strength and pore-pressure measurements from 57 dynamic cone penetration tests in sediments of Mecklenburg (n?=?51), Eckernförde (n?=?2) and Gelting (n?=?4) bays, western Baltic Sea, characterised by thick mud layers and partially free microbial gas resulting from the degradation of organic material. In Mecklenburg and Eckernförde bays, sediment sampling by nine gravity cores served sedimentological characterisation, analyses of geotechnical properties, and laboratory shear tests. At selected localities, high-resolution echo-sounder profiles were acquired. Our aim was to deploy a dynamic cone penetrometer (CPT) to infer sediment shear strength and cohesion of the sea bottom as a function of fluid saturation. The results show very variable changes in pore pressure and sediment strength during the CPT deployments. The majority of the CPT measurements (n?=?54) show initially negative pore-pressure values during penetration, and a delayed response towards positive pressures thereafter. This so-called type B pore-pressure signal was recorded in all three bays, and is typically found in soft muds with high water contents and undrained shear strengths of 1.6–6.4 kPa. The type B signal is further affected by displacement of sediment and fluid upon penetration of the lance, skin effects during dynamic profiling, enhanced consolidation and strength of individual horizons, the presence of free gas, and a dilatory response of the sediment. In Mecklenburg Bay, the remaining small number of CPT measurements (n?=?3) show a well-defined peak in both pore pressure and cone resistance during penetration, i.e. an initial marked increase which is followed by exponential pore-pressure decay during dissipation. This so-called type A pore-pressure signal is associated with normally consolidated mud, with indurated clay layers showing significantly higher undrained shear strength (up to 19 kPa). In Eckernförde and Gelting bays pore-pressure response type B is exclusively found, while in Mecklenburg Bay types A and B were detected. Despite the striking similarities in incremental density increase and shear strength behaviour with depth, gas occurrence and subtle variations in the coarse-grained fraction cause distinct pore-pressure curves. Gaseous muds interbedded with silty and sandy layers are most common in the three bays, and the potential effect of free gas (i.e. undersaturated pore space) on in situ strength has to be explored further.     

Composition and properties of glacigenic sediments in the southwestern Barents Sea

Abstract

The composition and properties of glacigenic sediments in the southwestern Barents Sea are described based on data from 33 shallow boreholes (< 143 m below seabed) and 11 seabed cores (<4.2m below seabed). The cores are tied into a regional seismostratigraphic framework, illustrating the relationships between different boreholes.

A massive, muddy diamicton (silty, sandy clay with scattered gravel) is found in nearly all cores. Average clay content (<2 pm) of this lithology is about 38%, but varies between about 25% and 50%. Short intervals of finely laminated, waterlain sediments or gravelly sand are cored in a few occasions. A high content of sand and gravel in the cores from near the Norwegian coast shows an influence of sediment input from the mainland, while material eroded from sedimentary rocks dominates farther offshore.

The data presented on physical properties include undisturbed and remolded undrained shear strength, natural water content, bulk density, compressional sound velocity (P waves), Atterberg consistency limits, effective preconsolidation pressure, and consolidation coefficient.

Prediction of overconsolidation from seismic mapping of erosional surfaces is confirmed by the borehole cores. High compaction is found both in Weichselian and older deposits, with a general increase in compaction toward the east as well as toward shallower water. Cores that are “underconsolidated” at their present burial depth are also reported.

The average compressional sound velocity is about 1780 m/s for the borehole cores, 1550 m/s for the seabed cores, and increases with increasing shear strength and consolidation. Both horizontal and vertical sound velocities are measured in several cores, and although the data have a considerable scatter, a slightly aniso‐tropic sound velocity is indicated.     

Physical and Acoustic Properties of Gas-bearing Sediments in Jinhae Bay,the South Sea of Korea

High-resolution seismic survey and sediment core sampling were conducted to investigate acoustic characteristics of gas-bearing sediments in Jinhae Bay, the southeast of Korea. The sediment in Jinhae Bay is mostly homogenous mud deposited after the Holocene transgression. Along with the 410 km of chirp seismic profiling, five piston core samples were collected on the track lines.

Gassy sediments are common and occur widely in the bay. Core samples were analyzed for sediment texture, physical properties (porosity, water content, bulk density, and grain density), acoustic properties (compressional wave velocity and attenuation), and electrical resistivity. X-radiograph image analysis was also performed to observe the shape of degassing cracks. There is no significant downcore variation on physical and sediment textures regardless of existence of gas bubbles. However, compressional wave velocity dramatically decreases from average 1480 to 1380～739 m/s for the cores that penetrate the gas-bearing zones. This is probably due to degassying cracks that developed by escaping gases and free gas bubbles that are still trapped in the cores. Electrical resistivity is the only geotechnical property that increases in the gas-bearing zone where compressional wave velocity abruptly decreases. This indicates the possibility of using both electrical resistivity as an index variable as well as to compressional wave velocity to identify gassy sediment microstructure because there are little changes in texture and composition of sediment.