Imaging of Buried Archaeological Materials: The Reflection Properties of Archaeological Wood

Effective marine archaeological site management demands detailed information on not only the spatial distribution of artefacts but also the degradation state of the materials present. Although sonar methods have frequently been used in an attempt to detect buried wooden shipwrecks they are currently unable to indicate their degradation state. To assess the sensitivity of acoustic measurements to changes in the degradation state of such material, and hence the potential for sonars to quantify degradation, laboratory measurements of compressional wave velocity, as well as bulk density for oak and pine samples, in varying states of decay, were undertaken. These data enabled the calculation of theoretical reflection coefficients for such materials buried in various marine sediments. As wood degrades, the reflection coefficients become more negative, resulting in the hypothesis that the more degraded wood becomes, the easier it should be to detect. Typical reflection coefficients of the order of −0.43 and −0.52 for the most degraded oak and pine samples in sand are predicted. Conversely, for wood exposed to seawater the predicted reflection coefficients are large and positive for undegraded material (0.35 for oak, 0.18 for pine) and decrease to zero or slightly below for the most degraded samples. This indicates that exposed timbers, when heavily degraded, can be acoustically transparent and so undetectable by acoustic methods. Corroboration of these experimental results was provided through comparison with high resolution seismic reflection data that has been acquired over two shipwrecks.     

Interference fringes on GLORIA side-scan sonar images from the Bering Sea and their implications

GLORIA side-scan sonographs from the Bering Sea Basin show a complex pattern of interference fringes sub-parallel to the ship's track. Surveys along the same trackline made in 1986 and 1987 show nearly identical patterns. It is concluded from this that the interference patterns are caused by features in the shallow subsurface rather than in the water column. The fringes are interpreted as a thin-layer interference effect that occurs when some of the sound reaching the seafloor passes through it and is reflected off a subsurface layer. The backscattered sound interferes (constructively or desctructively) with the reflected sound. Constructive/destructive interference occurs when the difference in the length of the two soundpaths is a whole/half multiple of GLORIA's 25 cm wavelength. Thus as range from the ship increases, sound moves in and out of phase causing bands of greater and lesser intensity on the GLORIA sonograph. Fluctuations (or wiggles) of the fringes on the GLORIA sonographs relate to changes in layer thickness. In principle, a simple three dimensional image of the subsurface layer may be obtained using GLORIA and bathymetric data from adjacent (parallel) ship's tracks. These patterns have also been identified in images from two other systems; SeaMARC II (12 kHz) long-range sonar, and TOBI (30 kHz) deep-towed sonar. In these, and other cases world-wide, the fringes do not appear with the same persistence as those seen in the Bering Sea.     

Waveform Shaping of Sonar Transducers for Improving the Vertical Resolution in Sub-bottom Sediments Profiling

Vertical resolution is of fundamental importance in sonar exploration and is directly related to the duration of the acoustic pulse generated by the transducer. The shorter the radiated pulse, the higher the vertical resolution. Many sub-bottom profiling sonar systems use piezoelectric transducers because they are reversible and well understood. Piezoelectric projectors are normally resonant transducers, which are intrinsically narrowband. A piezoelectric transducer is usually driven by a tone-burst. However, it is possible to use Fourier techniques to find a pre-compensated electrical driving function so that the transducer radiates a prescribed wider band acoustic waveform. This technique can be applied to synthesize zero-phase cosine-magnitude, Gaussian, and bionic pulses, with a conventional sandwich transducer. Zero-phase cosine-magnitude waveforms provide minimum length pulses (and therefore maximum resolution) within a prescribed frequency band.The aim of this paper is to illustrate the synthesis of wideband acoustic pulses using an underwater piezoelectric projector. The conventional acoustic waveform radiated when a Tonpiltz transducer is transiently excited using a “click” and allows its frequency response function to be measured. This function is used to design the electrical signal which then drives the transducer so that it radiates the shortest pulse compatible with its mechanical response. The significant resolution enhancement of the waveform shaping process is illustrated by its application to a sediment wedge model.     

Remote estimation of surficial seafloor properties through the application Angular Range Analysis to multibeam sonar data

The variation of the backscatter strength with the angle of incidence is an intrinsic property of the seafloor, which can be used in methods for acoustic seafloor characterization. Although multibeam sonars acquire backscatter over a wide range of incidence angles, the angular information is normally neglected during standard backscatter processing and mosaicking. An approach called Angular Range Analysis has been developed to preserve the backscatter angular information, and use it for remote estimation of seafloor properties. Angular Range Analysis starts with the beam-by-beam time-series of acoustic backscatter provided by the multibeam sonar and then corrects the backscatter for seafloor slope, beam pattern, time varying and angle varying gains, and area of insonification. Subsequently a series of parameters are calculated from the stacking of consecutive time series over a spatial scale that approximates half of the swath width. Based on these calculated parameters and the inversion of an acoustic backscatter model, we estimate the acoustic impedance and the roughness of the insonified area on the seafloor. In the process of this inversion, the behavior of the model parameters is constrained by established inter-property relationships. The approach has been tested using a 300 kHz Simrad EM3000 multibeam sonar in Little Bay, NH. Impedance estimates are compared to in situ measurements of sound speed. The comparison shows a very good correlation, indicating the potential of this approach for robust seafloor characterization.     

海底勘查技术的最新发展

本文将介绍用于探测海底三维地质特征的海底勘查的最新发展。它主要包括海底地形测绘技术，海底形貌观测技术、海底地层声学探测技术等。     

Automatic Registration of TOBI Side-Scan Sonar and Multi-Beam Bathymetry Images for Improved Data Fusion

Deep towed side-scan sonar vehicles such as TOBI acquire high quality imagery of the seafloor with very high spatial resolution but poor locational accuracy. Fusion of the side-scan sonar data with bathymetry data from an independent source is often desirable to reduce ambiguity in geological interpretations, to aid in slant-range correction and to enhance seafloor representation. The main obstacle to fusion is accurate registration of the two datasets.The application of hierarchical chamfer matching to the registration of TOBI side-scan sonar images and multi-beam swath bathymetry is described. This matches low level features such as edges in the TOBI image, with corresponding features in a synthetic TOBI image created by simulating the flight of the TOBI vehicle through the bathymetry. The method is completely automatic, relatively fast and robust, and much easier than manual registration. It allows accurate positioning of the TOBI vehicle, enhancing its usefulness as a research tool. The method is illustrated by automatic registration of TOBI and multi-beam bathymetry data from the Mid-Atlantic Ridge.     

Channelled erosion through a marine dump site of dredge spoils at the mouth of the Puyallup River, Washington State, USA

Channels are relatively common on river-mouth deltas, but the process by which they arise from river sediment discharge is unclear because they can potentially be explained either by negatively buoyant (hyperpycnal) flows produced directly from the river outflow or by flows generated by repeated failure and mobilisation of sediment rapidly deposited at the delta front. Channels eroded through a dump site of dredge spoils are described here from multibeam and older sonar data collected in Commencement Bay, at the mouth of the Puyallup River. Shallow channels on the seaward upper surface of the dump site, away from any flows that could have been produced by delta front failures, suggest that at least some hyperpycnal flows were produced directly from the positively buoyant river outflow up to 200 m from the edge of the river mouth platform. The form of channel bed erosion is revealed by the longitudinal shape of the main eroded channel compared with the adjacent dump site profile. It suggests that the channel evolved by its steep front retreating, rather than by simple vertical entrenchment or diffusive-like evolution of the profile, a geometry interpreted as evidence that repeated failure of the bed occurred in response to shear stress imposed by bottom-travelling flows. Model calculations based on shear strengths back-calculated from the geometry of channel wall failures suggest that, if the main channel were eroded solely by hyperpycnal flows, their generation was remarkably efficient in order to create flows vigorous enough to cause channel bed failure. Besides the sediment concentration and discharge characteristics that have been considered to dictate the ability of rivers to produce hyperpycnal flows, it is suggested that the timing of floods with respect to the tidal cycle should also be important because extreme low tides may be needed to ensure that coarse sediment is transferred vigorously to the edge of river mouth platforms.