Modelling the effect of changing precipitation inputs on deep soil water utilization

Forests in the Southeastern United States are predicted to experience future changes in seasonal patterns of precipitation inputs as well as more variable precipitation events. These climate change‐induced alterations could increase drought and lower soil water availability. Drought could alter rooting patterns and increase the importance of deep roots that access subsurface water resources. To address plant response to drought in both deep rooting and soil water utilization as well as soil drainage, we utilize a throughfall reduction experiment in a loblolly pine plantation of the Southeastern United States to calibrate and validate a hydrological model. The model was accurately calibrated against field measured soil moisture data under ambient rainfall and validated using 30% throughfall reduction data. Using this model, we then tested these scenarios: (a) evenly reduced precipitation; (b) less precipitation in summer, more in winter; (c) same total amount of precipitation with less frequent but heavier storms; and (d) shallower rooting depth under the above 3 scenarios. When less precipitation was received, drainage decreased proportionally much faster than evapotranspiration implying plants will acquire water first to the detriment of drainage. When precipitation was reduced by more than 30%, plants relied on stored soil water to satisfy evapotranspiration suggesting 30% may be a threshold that if sustained over the long term would deplete plant available soil water. Under the third scenario, evapotranspiration and drainage decreased, whereas surface run‐off increased. Changes in root biomass measured before and 4 years after the throughfall reduction experiment were not detected among treatments. Model simulations, however, indicated gains in evapotranspiration with deeper roots under evenly reduced precipitation and seasonal precipitation redistribution scenarios but not when precipitation frequency was adjusted. Deep soil and deep rooting can provide an important buffer capacity when precipitation alone cannot satisfy the evapotranspirational demand of forests. How this buffering capacity will persist in the face of changing precipitation inputs, however, will depend less on seasonal redistribution than on the magnitude of reductions and changes in rainfall frequency.     

A New Wavelet Method for Identification of Eddies and Assessment of Incidents on Islands of the Eastern Caribbean

Using two dimensional continuous wavelet transforms, a novel method for identification of mesoscale eddies is presented to facilitate extraction of characteristics for area, amplitude, type, and location from maps of sea level anomalies. In comparison with the previously established growing method for eddy identification, it is found that the wavelet method identifies more than twice the number of eddies and is particularly better at resolving small eddies down to the 0.25 degree resolution of the data. Such research into eddy identification and tracking is significant to the assessment of eddies with potential to impact on coastlines of small islands. The method is applied to the identification of eddies on tracks towards islands of the Eastern Caribbean over 23?years. Spatial and temporal variation in rate of occurrence and magnitude is established. For Barbados there is an average of 9 anticyclonic incidents a year with maximum amplitude of typically 0.22?m in the dry seasons and 0.16?m in the wet seasons. Seasonal variation is reversed for the other islands with twice the number of anticyclonic incidents having maximum amplitudes of about 0.20?m annually.     

复杂地形景区三维导览图的设计与实现

为满足复杂地形景区对三维地图导览的需求,构建更为清晰的三维地图模型,提供良好的三维导览地图设计方案显得尤为重要。为了更好地与卫星影像进行贴合,DEM数据的采样密度要与卫星影像的分辨率一致。本文通过对比当下常用的四种空间插值方法的适用范围与运用特点,设置相关阈值及权重,直观比较了四种插值方法产生的插值结果,选择更适合复杂景区DEM插值的插值方法并对其进行精度提升,以此得到符合精度要求的DEM数据。最后利用相应地区的卫星影像进行地图投影及影像贴图,两种数据结合构建复杂景区的三维地图模型,给游客带来更为精确直观的定位信息和空间要素信息。     

Fully coupled elastoplastic hydro-mechanical analysis of unsaturated porous media using a meshfree method

This paper presents the first application of an advanced meshfree method, ie, the edge-based smoothed point interpolation method (ESPIM), in simulation of the coupled hydro-mechanical behaviour of unsaturated porous media. In the proposed technique, the problem domain is spatially discretised using a triangular background mesh, and the polynomial point interpolation method combined with a simple node selection scheme is adopted for creating nodal shape functions. Smoothing domains are formed on top of the background mesh, and a constant smoothed strain, created by applying the smoothing operation over the smoothing domains, is assigned to each smoothing domain. The deformation and flow models are developed based on the equilibrium equation of the mixture, and linear momentum and mass balance equations of the fluid phases, respectively. The effective stress approach is followed to account for the coupling between the flow and deformation models. Further coupling among the phases is captured through a hysteretic soil water retention model that evolves with changes in void ratio. An advanced elastoplastic constitutive model within the context of the bounding surface plasticity theory is employed for predicting the nonlinear behaviour of soil skeleton. Time discretisation is performed by adopting a three-point discretisation method with growing time steps to avoid temporal instabilities. A modified Newton-Raphson framework is designed for dealing with nonlinearities of the discretised system of equations. The performance of the numerical model is examined through a number of numerical examples. The state-of-the-art computational scheme developed is useful for simulation of geotechnical engineering problems involving unsaturated soils.     

A novel coupled FDM-DEM modelling method for flexible membrane boundary in laboratory tests

Difficulties are involved in discrete element method (DEM) modelling of the flexible boundary, that is, the membranes covering the soil sample, which can be commonly found in contemporary laboratory soil tests. In this paper, a novel method is proposed wherein the finite difference method (FDM) and DEM are coupled to simulate the rubber membrane and soil body, respectively. Numerical plane strain and triaxial tests, served by the flexible membrane, are implemented and analysed later. The effect of the membrane modulus on the measurement accuracy is considered, with analytical formulae derived to judge the significance of this effect. Based on an analysis of stress-strain responses and the grain rotation field, the mechanical performances produced by the flexible and rigid lateral boundaries are compared for the plane strain test. The results show that (1) the effect of the membrane on the test result becomes more significant at larger strain level because the membrane applies additional lateral confining pressure to the soil body; (2) the tested models reproduce typical stress and volumetric paths for specimens with shear bands; (3) for the plane strain test, the rigid lateral boundary derives a much higher peak strength and larger bulk dilatation, but a similar residual strength, compared with the flexible boundary. The latter produces a more uniform (or ‘diffuse') rotation field and more mobilised local kinematics than does the former. All simulations show that the proposed FDM-DEM coupling method is able to simulate laboratory tests with a flexible boundary membrane.     

Subsurface flow measurements using passive flux meters in variably-saturated cold-regions landscapes

To date, passive flux meters have predominantly been applied in temperate environments for tracking the movement of contaminants in groundwater. This study applies these instruments to reduce uncertainty in (typically instantaneous) flux measurements made in a low-gradient, wetland dominated, discontinuous permafrost environment. This method supports improved estimation of unsaturated and over-winter subsurface flows which are very difficult to quantify using hydraulic gradient-based approaches. Improved subsurface flow estimates can play a key role in understanding the water budget of this landscape.     

圆形数值波浪水池斜向和多向入射波浪模拟研究

为了研究斜向入射波浪,基于三维不可压缩两相流模型,开发了一套圆形数值波浪水池数值模型。在圆形波浪水池中,通过源项造波法成功生成了任意入射方向的波浪,并且利用人工摩擦项模拟阻尼区以数值耗散反射波浪。模型基于嵌入式多块网格体系,采用FVM法(finite volume method)离散Navier-Stokes方程,VOF法(volume of fluid)追踪自由水面。试验结果表明,斜向入射波浪的模拟结果与理论值基本一致,圆形波浪水池在模拟斜向入射波浪时,有效区域的面积较传统波浪水池显著增大,而且有效区域受波浪入射角度的影响也较小。同时,通过叠加多列斜向入射波浪,模拟出了多向交叉波列,并通过与理论结果对比,发现其具有较高的精度。     

Revisiting the existence of an effective stress for wet granular soils with micromechanics

A possible effective stress variable for wet granular materials is numerically investigated based on an adapted discrete element method (DEM) model for an ideal three‐phase system. The DEM simulations consider granular materials made of nearly monodisperse spherical particles, in the pendular regime with the pore fluid mixture consisting of distinct water menisci bridging particle pairs. The contact force‐related stress contribution to the total stresses is isolated and tested as the effective stress candidate for dense or loose systems. It is first recalled that this contact stress tensor is indeed an adequate effective stress that describes stress limit states of wet samples with the same Mohr‐Coulomb criterion associated with their dry counterparts. As for constitutive relationships, it is demonstrated that the contact stress tensor used in conjunction with dry constitutive relations does describe the strains of wet samples during an initial strain regime but not beyond. Outside this so‐called quasi‐static strain regime, whose extent is much greater for dense than loose materials, dramatic changes in the contact network prevent macroscale contact stress‐strain relationships to apply in the same manner to dry and unsaturated conditions. The presented numerical results also reveal unexpected constitutive bifurcations for the loose material, related to stick‐slip macrobehavior.     

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.