基于ROMS和4DVAR的沿轨与网格化SSH数据同化效果评价

Remote sensing products are significant in the data assimilation of an ocean model. Considering the resolution and space coverage of different remote sensing data, two types of sea surface height(SSH) product are employed in the assimilation, including the gridded products from AVISO and the original along-track observations used in the generation. To explore their impact on the assimilation results, an experiment focus on the South China Sea(SCS) is conducted based on the Regional Ocean Modeling System(ROMS) and the four-dimensional variational data assimilation(4 DVAR) technology. The comparison with EN4 data set and Argo profile indicates that, the along-track SSH assimilation result presents to be more accurate than the gridded SSH assimilation, because some noises may have been introduced in the merging process. Moreover, the mesoscale eddy detection capability of the assimilation results is analyzed by a vector geometry–based algorithm. It is verified that, the assimilation of the gridded SSH shows superiority in describing the eddy's characteristics, since the complete structure of the ocean surface has been reconstructed by the original data merging.     

Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.     

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.     

铜藻(Sargassum horneri)在营养限制胁迫后对NH4-N的超补偿吸收研究

以经济马尾藻铜藻(Sargassum horneri)为研究材料,研究了其在营养限制胁迫后对NH_4-N的超补偿吸收情况。实验分营养限制和恢复营养两个阶段进行,每个阶段均设置饥饿处理组、饱和处理组和正常对照组。铜藻在低营养限制胁迫(饥饿)下培养10天后,恢复营养盐培养3天,分别采用次溴酸盐氧化法和锌镉还原法测定培养液中的NH_4-N和NO_3-N的浓度。本文研究发现,饥饿处理组中铜藻吸收氨氮的速率远高于正常对照组和饱和处理组,在恢复培养第一天时,饥饿处理组对NH_4-N的吸收速率最高为14.94μmol/(g·h),与正常对照组及饱和处理组间差异显著。在恢复培养的后两天,三个处理组中铜藻对NH_4-N的吸收速率差异慢慢变小,直至最后几乎相同。三组对NO_3-N没有表现出较高的吸收,最高仅为6.15μmol/(g·h),结果表明:氮源包括NH_4-N和NO_3-N时,铜藻优先选择吸收NH_4-N。实验后称重测定生长速率:对照组、饥饿处理组和饱和组生长率(SGR)分别为8.48%、8.86%、8.01%,ANOVA方差分析表明,三者存在显著差异(P=0.0320.05),从而证实了铜藻也存在超补偿生长的现象。     

基于圆柱多段拟合的隧道中轴线提取方法研究

提出基于圆柱多段拟合的隧道中轴线提取方法。首先对隧道点云数据进行预处理，并将点云按隧道走向分成不同区段；然后对各区段依据轴线与表面点云法线垂直关系，提取精度较低的中轴线；最后对各区段利用圆柱多段拟合，提取精度较高的中轴线。实验表明，隧道中轴线的提取在一定的采样区间具有较高的稳定性，对直线和弯曲的圆形隧道有良好的适用性，算法可靠，精度较高。     

资源三号和天绘一号卫星影像无控联合平差精度分析

近年来国产卫星传感器类型日益丰富，使用自主可控的国产卫星影像进行生产和研究的需求越来越大，多源国产卫星影像联合平差的精度分析显得尤为重要。本文针对在立体测图生产中，资源三号卫星影像在时相较旧、噪声较大、云覆盖和摄影漏洞等特殊困难的条件下，利用天绘一号卫星影像进行补漏生产的情况，最终分析并验证了两者无控联合平差的可行性和成果精度。     

基于重力测点和段差变化的前郭5.8级震群研究与三维反演

利用东北地区近几年流动重力观测数据，分析前郭5.8级震群周边重力点值的时序变化特征，并基于重力段差变化对东北地区整体和局部重力变化引入能够反映异常显著性程度的指标量G和C值，最后对前郭5.8级震群前的重力场动态变化作三维密度反演。结果表明：1）前郭5.8级震群发震构造两侧的局部重力变化具有较明显的差异性，其变化趋势可作为识别构造活化或解耦运动的标志；2）显著性指标量G和C值能够为地震重力前兆的定量描述提供新思路；3）震前重力变化的反演结果显示地震发生在质量运移的过渡区域，垂向反演结果对本次地震的震源深度有一定的揭示意义。     

Bacterial productivity in the Prydz Bay and its adjacent waters,Antarctic

1　IntroductionBacteriaandtheiractivitiesplayanimportantroleintheelementalbiogeochemicalcyclesandenergytransformingintheocean (Zhenetal.1 997) .DortchandPackard(1 989) proposedthatfoodwebsintheeutrophicwatersaredominatedbythebiomassofprimaryproducerswhilefoodwebsintheoligotrophicwatersaredominatedbythebiomassofmicrobes.Heterotrophicbacteriahadbeenshowntoplayanimportantroleinthedecompositionoflarge ,rapidlysinkingorganicparticleswithinandbelowtheeuphot iczone ,andfurthertoaffecttheelementaldyn…     

GPS/LEO掩星观测的变分同化技术

在简单介绍GPS/LEO掩星探测大气的发展历史和科学意义之后,详细阐述了反演的基本原理;分析了标准反演中存在的问题,并说明一维变分同化(1DVAR)在反演方法中的重要性;给出了一维变分同化中价值函数的求解,以及各种同化因子;简单介绍了对当前气象学中普遍使用的四维变分同化(4DVAR);重点讨论了各种同化方法,以及使用各种同化因子的优缺点。最后,通过CHAMP卫星的观测实例分析,验证了GPS数据在数值天气预报(NWP)中的作用,以及相对于标准反演法一维变分对气象要素的改进。     

三维旋转扫描测量平台设计与实现

本设计主要用于360°旋转的三维扫描,实现角度数据的实时获取。设计中采用单片机控制交流伺服电机进行自定的角度、速度与方向的旋转并实时上传时间、角度数据至上位机进行处理,实现了对平台旋转精度的控制与检测,着重研究了该传感器误差源的产生,对实际应用中的误差进行了定量分析,利用偏心改正、4分频等方法减少了误差,提高了参数精度。角度范围为360°,角度分辨率为0.01°。