Analysis of Post-Failure Slope Movements within the Framework of Hazard and Risk Analysis

The paper first recalls briefly a methodological framework to assess landslide hazard and risk analysis in terms of predisposition, triggering andrevealing factors. This framework, that reflects the mechanisms involved in the landslide, is based on the Geotechnical Characterisation of slope movements proposed by Vaunat et al. (1994) and Leroueil et al. (1996). The Geotechnical Characterisation can be schematized by a 3-D matrix having the following axes: types of movement; types ofmaterial; and the four stages of movement: pre-failure, failure, post-failure andreactivation. For each relevant element of this 3-D matrix, there is a characterisationsheet including: the controlling laws and parameters, the predisposition factors, thetriggering or aggravating factors, the revealing factors and the consequences of the movement. The paper focuses afterwards on the post-failure stage, which generallyis the most destructive, and on the mobility index. It is shown that this laterindex can be described as the product of sub-indices associated with failure, brittlenessof the material, ability of the soil to develop pore pressures, geometry of the moving soil mass and characteristics of the terrain. It is also shown how these aspectscan be incorporated into the Geotechnical characterisation of slope movements. This seems to provide a rational basis for examining slope movements at the post-failure stage and assessing associated risks.     

A densification mechanism to model the mechanical effect of methane hydrates in sandy sediments

Recent pore-scale observations and geomechanical investigations suggest the lack of true cohesion in methane hydrate-bearing sediments (MHBSs) and propose that their mechanical behavior is governed by kinematic constrictions at pore-scale. This paper presents a constitutive model for MHBS, which does not rely on physical bonding between hydrate crystals and sediment grains but on the densification effect that pore invasion with hydrate has on the sediment mechanical properties. The Hydrate-CASM extends the critical state model Clay and Sand Model (CASM) by implementing the subloading surface model and introducing the densification mechanism. The model suggests that the decrease of the sediment available void volume during hydrate formation stiffens its structure and has a similar mechanical effect as the increase of sediment density. In particular, the model attributes stress-strain changes observed in MHBS to the variations in sediment available void volume with hydrate saturation and its consequent effect on isotropic yield stress and swelling line slope. The model performance is examined against published experimental data from drained triaxial tests performed at different confining stress and with distinct hydrate saturation and morphology. Overall, the simulations capture the influence of hydrate saturation in both the magnitude and trend of the stiffness, shear strength, and volumetric response of synthetic MHBS. The results are validated against those obtained from previous mechanical models for MHBS that examine the same experimental data. The Hydrate-CASM performs similarly to previous models, but its formulation only requires one hydrate-related empirical parameter to express changes in the sediment elastic stiffness with hydrate saturation.     

Consequences on water retention properties of double-porosity features in a compacted silt

The paper deals with an experimental investigation aimed at studying microstructural features and their consequences on water retention properties of statically compacted unsaturated silt. The evolution of the microstructure of the aggregate fabric induced by compaction is investigated by studying the pore size distribution changes under different initial conditions (void ratio and water content). The material used is low plasticity silt from Jossigny near Paris, France. A series of mercury intrusion porosimetry tests (MIP) were performed at different void ratios and water contents to provide microstructural information. The arrangement of aggregation/particles and pore network was also investigated with environmental scanning electron microscopy (ESEM). The MIP data were used to determine the water retention curve on drying for the specific pore network configuration induced on compaction. The MIP data were used to formulate and calibrate a multimodal water retention model for a specific pore network configuration, which is obtained by linear superposition of subcurves of a modified van Genuchten type. The study is then complemented with controlled suction oedometer tests on compacted samples to obtain the water retention properties of the material at two different void ratios. Finally, we compare the water retention properties obtained by the simulated progression of the different pore network configurations induced on the hydraulic path with the water retention properties under suction-controlled conditions. Good agreement between the two methods for the drying path is reached.     

Thermal Conductivity of Argillaceous Rocks: Determination Methodology Using In Situ Heating Tests

This study focuses on the characterisation of thermal conductivity for three potential host rocks for radioactive waste disposal. First, the heat conduction process is reviewed on the basis of an analytical solution and key aspects related to anisotropic conduction are discussed. Then the existing information on the three rocks is summarised and a broad uncertainty range of thermal conductivity is estimated based on the mineralogical composition. Procedures to backanalyse the thermal conductivity on the basis of in situ heating tests are assessed and a methodology is put forward. Finally, this methodology is used to estimate the impact of experimental uncertainties and applied to the four in situ heating tests. In the three potential host rocks, a clear influence of the bedding planes was identified and anisotropic heat conduction was shown to be necessary to interpret the observed temperature field. Experimental uncertainties were also shown to induce a larger uncertainty on the anisotropy ratio than on the equivalent thermal conductivity defined as the geometric mean of the thermal conductivity in the three principal directions.     

Revisiting the thermodynamics of hardening plasticity for unsaturated soils

A thermodynamically consistent extension of the constitutive equations of saturated soils to unsaturated conditions is often worked out through the use of a unique ‘effective’ interstitial pressure, accounting equivalently for the pressures of the saturating fluids acting separately on the internal solid walls of the pore network. The natural candidate for this effective interstitial pressure is the space averaged interstitial pressure. In contrast experimental observations have revealed that, at least, a pair of stress state variables was needed for a suitable framework to describe stress–strain–strength behaviour of unsaturated soils. The thermodynamics analysis presented here shows that the most general approach to the behaviour of unsaturated soils actually requires three stress state variables: the suction, which is required to describe the invasion of the soil by the liquid water phase through the retention curve; two effective stresses, which are required to describe the soil deformation at water saturation held constant. However a simple assumption related to the plastic flow rule leads to the final need of only a Bishop-like effective stress to formulate the stress–strain constitutive equation describing the soil deformation, while the retention properties still involve the suction and possibly the deformation. Commonly accepted models for unsaturated soils, that is the Barcelona Basic Model and any approach based on the use of an effective averaged interstitial pressure, appear as special extreme cases of the thermodynamic formulation proposed here.     

Coupled analysis of a backfill hydration test

BACCHUS2 in situ isothermal wetting experiment has been analysed by means of a coupled flow-deformation approach. Backfill material, a mixture of Boom clay powder and high density pellets, has been extensively tested in the laboratory in order to determine its hydraulic and mechanical properties. Parameters of constitutive equations were derived from this experimental data base. Two mechanical constitutive models have been used in the simulation of the ‘in situ’ experiment: a state surface approach and an elastoplastic model. Calculations have shown several features of the hydration process which help to understand the behaviour of expansive clay barriers. Predictions using both models have been compared with each other and with actual measurement records. This has allowed a discussion of the comparative mertis of both approaches and the identification of some critical parameters of backfill behaviour. Overall agreement between calculations and field measurements is encouraging and shows the potential of the methods developed to model the behaviour of engineered clay barriers in the context of nuclear waste disposal. © 1998 by John Wiley & Sons, Ltd.     

An effective combined framework for modelling the time-dependent behaviour of soft structured clays

A constitutive framework for the simulation of the time-dependent behaviour of soft structured clays has been developed from the combination of a number of existing modelling approaches. The formulation accounts, in a natural way, for time-dependent phenomena such as loading rate dependency, stress relaxation, ageing, and creep deformations under constant load. In addition, the effect of structure is accounted for. To demonstrate the potential of the proposed approach, a specific model based on this framework is described and applied to the simulation of a number of relevant laboratory tests from the literature.