Re-Suspension Technique for Improving Organic Rich Sediment-Water Quality in a Shallow Sea Area

The re-suspension method consists of (1) dispersion of the sediment by air-water jets, (2) pumping of the suspension (small particles and organic matter), (3) settlement in a tank, (4) filtration and (5) disposal of solids (followed by incineration in this case). The pilot test was performed to clean up an area of 3000 m². The dispersed depth of the bottom was approximately 50 cm. The time spent for the work was two weeks. The amount of re-suspended solid removed from the bottom was about 8 tonnes in dry mass. Since the solids contain high concentrations of chemical oxygen demand (COD), total phosphorous (T-P), total nitrogen (T-N) and sulfides, the remaining sediment was considerably improved. Quantitative analyses showed that the full-scale implementation would enable the removal of about 10% of the re-suspended solids, and reduce COD by 95%, T-P by 50%, T-N by 100% and sulfide by 75% for re-deposited sediments in comparison to the original sediments.     

Microtopographic properties of sparse moss vegetation in the Antarctic polar desert

The effect of topography on moss vegetation is examined to clarify the processes that affect the colonization of polar deserts on continental Antarctica. Data on the presence of the mosses Bryum pseudotriquetrum and Pottia heimii, and relative altitude were recorded. The altitude measurements were used to infer the underlying topographical attributes of the substrate in the study plots. Specifically, the local distribution of moss plants was clarified using the topographical attributes to construct generalized linear mixed models (GLMMs). The models suggested that steep slopes and convex microhabitats within areas of concave general relief (at the plot scale 4 × 4 m) promoted the establishment of moss. This correspondence to general relief was more apparent for B. pseudotriquetrum than for P. heimii. Among the study plots, general relief was found to be an important determinant of the precise spatial distribution of B. pseudotriquetrum. The standard surface estimated using the robust methods presented in this study is shown to be more accurate for describing moss distribution than the prevailing least-squares method.     

Speciation of Chromium in Artificially Contaminated Soil Reference Material GSJ JSO-2 Using XANES and Chemical Extraction Methods

The oxidation states of chromium in GSJ JSO-2 (artificially contaminated soil) and three other geochemical reference materials (GSJ JSO-1, JLS-1 and JMS-1) were observed using X-ray near edge structure (XANES). For comparison, other artificially contaminated soil materials (mimic-JSO-2) were prepared by adding Cr(VI) into JSO-1. Their oxidation states of chromium were determined using XANES. The chromium contents were 1118 μg g^-1 for JSO-2, 1352 μg g^-1 for mimic-JSO-2 and 69-113 μg g^-1 for the other reference materials. Most chromium was present as hexavalent in mimic-JSO-2. No hexavalent species were detected in other samples. These results for chromium oxidation state in JSO-2 and mimic-JSO-2 obtained with XANES resembled those obtained from a chemical extraction method. The present JSO-2 has no trace of Cr(VI), although Cr(VI) was added as a major species during preparation. On the other hand, the content of Cr(VI) obtained in mimic-JSO-2 agreed with the original Cr(VI) content. A time-elapse study showed that Cr(VI) contents in mimic-JSO-2 decreased gradually to 70% of the original abundance during 240-day preservation in dry conditions. Moreover, the abundance of Cr(VI) decreased markedly to 15% after 240 days in the wet mimic-JSO-2 containing 20% m/m of water. These experiments suggested that soil humidity enhanced the reduction of Cr(VI) and that Cr(VI) was reduced even in dry conditions. Consequently, it is reasonable to infer that Cr(VI) doped into JSO-2 was completely reduced to Cr(III) during the preservation period of 5 years. The certification of the long-term stability of the chemical form in reference materials will be much more important in future.     

Coupled Ce-Nd isotope systematics and rare earth elements differentiation of the moon

¹³⁸Ce/¹⁴²Ce and ¹⁴³Nd/¹⁴⁴Nd isotope ratios of lunar samples are determined to constrain the petrogenetic differentiation and evolution of the moon. High-precision Ce-Nd isotope data, well-defined Rb-Sr isochrons, and rare earth elements (REE) abundances of lunar samples show that unexpectedly low La/Ce ratios of evolved lunar highland samples are preserved from at least 3.9 Ga. Precise analysis of REE abundances indicates that the low La/Ce ratio results from a depletion of La relative to other REE. This depletion can be seen in pristine KREEP basalts and Mg-suite rocks from 3.85 to 4.46 Ga. As REE abundances of all these samples are controlled by the presence of a KREEP component, the depletion was probably inherited from a late crystallization sequence of the lunar magma ocean related to the production of the original KREEP component.     

日本西南部四国增生复合体中的锰矿分布

Bedded manganese ore deposits occur in many localities within the accretionary belts of the Shikoku region, SW Japan. The deposits occur mostly in bedded chert or its metamorphosed equivalent. These chert-hosted manganese deposits are considered to have been manganese nodule/crust-bearing siliceous sediments on deep-sea floor and have been converted to manganese ores by low-grade metamorphism through subduction-accretion process. The mineral assemblages of the ores reflect the metamorphic grade of the accretionary complexes. On the other hand, iron-manganese deposits and some manganese deposits occurring directly over basalt are considered to have been the hydrothermal precipitates associated with submarine volcanism.     

Transport measurement with a horizontal and a vertical pipe microphone in a mountain stream: taking account of particle saltation

The pipe microphone has been shown to be an effective means for monitoring bedload transport in mountain streams. It is commonly installed perpendicular to the flow direction on a stable river bed, such as that of a check dam. Acoustic pulses caused by bedload collisions with the pipe are detected by a microphone. However, bedload particles saltating over the pipe remain undetected. To overcome this disadvantage, we installed a horizontal as well as a vertical pipe microphone in the Ashi‐arai‐dani supercritical channel located in the Hodaka mountain range, Japan. The vertical pipe was installed on the wall of the channel and the horizontal pipe was installed on the channel bed. The acoustic response of the horizontal pipe is expected to be larger than that of the vertical pipe, because the bedload concentration decreases with increasing height above the bed. However, at high amplifications, the peak pulse value from the vertical pipe is higher than that from the horizontal pipe. We explain this observation as follows: under high bedload discharge conditions, the pulses of the horizontal pipe are saturated but those of the vertical pipe are not. We proposed a ratio (R_hv) between the pulses detected by these sensors, and applied this ratio for calibrating the contemporaneous pulses detected by a microphone located immediately upstream of a bedload slot sampler. Indeed the R_hv‐corrected pulses correlated well with the bedload discharge calculated from the sampler, supporting our explanation. We conclude that bedload monitoring using concomitant vertical and horizontal pipe microphones can be used to calibrate centrally located pipe microphones when the bedload concentration is approximately homogeneous laterally across the width of the channel cross‐section, and thereby represent bedload discharges more accurately than with only a single pipe microphone. Copyright © 2017 John Wiley & Sons, Ltd.     

A specific Ce oxidation process during sorption of rare earth elements on biogenic Mn oxide produced by Acremonium sp. strain KR21-2

Sorption of rare earth elements (REEs) and Ce oxidation on natural and synthetic Mn oxides have been investigated by many researchers. Although Mn(II)-oxidizing microorganisms are thought to play an important role in the formation of Mn oxides in most natural environments, Ce oxidation by biogenic Mn oxide and the relevance of microorganisms to the Ce oxidation process have not been well understood. Therefore, in this study, we conducted sorption experiments of REEs on biogenic Mn oxide produced by Acremonium sp. strain KR21-2. The distribution coefficients, K_d(REE), between biogenic Mn oxide (plus hyphae) and 10 mmol/L NaCl solution showed a large positive Ce anomaly and convex tetrad effect variations at pH 3.8, which was consistent with previous works using synthetic Mn oxide. The positive Ce anomaly was caused by oxidation of Ce(III) to Ce(IV) by the biogenic Mn oxide, which was confirmed by analysis of the Ce L_III-edge XANES spectra. With increasing pH, the positive Ce anomaly and convex tetrad effects became less pronounced. Furthermore, negative Ce anomalies were observed at a pH of more than 6.5, suggesting that Ce(IV) was stabilized in the solution (<0.2 μm) phase, although Ce(III) oxidation to Ce(IV) on the biogenic Mn oxide was confirmed by XANES analysis. It was demonstrated that no Ce(III) oxidation occurred during sorption on the hyphae of strain KR21-2 by the K_d(REE) patterns and XANES analysis. The analysis of size exclusion HPLC-ICP-MS showed that some fractions of REEs in the filtrates (<0.2 μm) after sorption experiments were bound to organic molecules (40 and <670 kDa fractions), which were possibly released from hyphae. A line of our data indicates that the negative Ce anomalies under circumneutral pH conditions arose from Ce(III) oxidation on the biogenic Mn oxide and subsequent complexation of Ce(IV) with organic ligands. The suppression of tetrad effects is also explained by the complexation of REEs with organic ligands. The results of this study demonstrate that the coexistence of the biogenic Mn oxide and hyphae of strain KR21-2 produces a specific redox chemistry which cannot be explained by inorganic species.     

Comparative analysis of measurements of stratospheric aerosol by lidar and aerosol sonde above Ny-Ålesund in the winter of 1995 [Comparative analysis of lidar and OPC observations]

Solid polar stratospheric cloud (PSC) layers observed by lidar and a balloon-borne optical particle counter (OPC) on 17 December 1995 are reexamined in a comparative analysis framework. The typical radius of solid particles in the observed PSC is determined through the comparative analysis to have been approximately 2.3 μm. A backward trajectory analysis for the air mass in which the solid particles were observed shows that the air mass had experienced temperatures 2–3 K below the frost point of nitric acid tri-hydrate (NAT) during the 4 days preceding the observations. The back-trajectory analysis traces the air mass back to northern Greenland and Ellesmere Island on 16 December, one day before the observations. A microphysical box model is used to investigate possible mechanisms of formation for the observed solid particles. The results of this model suggest that the solid particles formed under mesoscale temperature fluctuations associated with mountain lee wave activity induced by the relatively high terrestrial elevations of northern Greenland and Ellesmere Island.     

Laboratory based continuous bedload monitoring in a model retention basin: Application of time domain reflectometry

In this study, we applied time domain reflectometry (TDR) to determine the deposition height and porosity of sediment at a fine spatiotemporal resolution, and developed a continuous bedload monitoring method that can be applied to pools in steep mountain rivers. The TDR monitoring system consisted of sensor probes, a cable tester, multiplexers and coaxial cables. When the embedded probes penetrated both water and sediment, the boundaries of the sediment and water were consistent with the transition points in the observed waveforms of each TDR measurement. A semi‐automatic analysis of the recorded TDR waveforms, which did not require calibration or parameter fitting, was conducted to establish continuous monitoring. In addition, a flume experiment was performed to test the monitoring system in a model retention basin connected to a flume, with sand of uniform grain size (1.4 mm diameter) supplied for 30 min. The sediment volume in the container representing the model basin was monitored using a load cell underlying the container and eight sensor probes, with a length of almost 0.27 m. The sediment thickness determined by the TDR indicated a gradual deposition, and was consistent with manual measurements. Despite a marginal overestimation of 13% for a sand feed of 30 kg, the sediment volume in the model retention basin and the bedload transport rate were successfully estimated. A combination of our monitoring system and other indirect methods, such as geophones, can potentially serve as useful tools for better understanding bedload transport processes in steep mountain streams. Copyright © 2018 John Wiley & Sons, Ltd.     

Characterization of slip zone associated with the 1999 Taiwan Chi-Chi earthquake: X-ray CT image analyses and microstructural observations of the Taiwan Chelungpu fault

To characterize the fault-related rocks within the Chelungpu fault, we performed X-ray computed tomography (CT) image analyses and microstructural observations of Hole B core samples from the Taiwan Chelungpu-fault Drilling Project. We identified the slip zone associated with the 1999 Chi-Chi earthquake, within the black gouge zone in the shallowest major fault zone, by comparison with previous reports. The slip zone was characterized by low CT number, cataclastic (or ultracataclastic) texture, and high possibility to have experienced a mechanically fluidized state. Taking these characteristics and previous reports of frictional heating in the slip zone into consideration, we suggested that thermal pressurization was the most likely dynamic weakening mechanism during the earthquake.