Investigation of moment-rotation relation in different joint types and evaluation of their effects on segmental tunnel lining

This paper presents the results of a numerical study that has been performed to investigate the different joint types that affect the moment-rotation relation and ultimate bending moment capacity of a joint. A 3D finite element method was adapted to establish elaborate numerical models of segments. To evaluate the possible differences in moment-rotation behavior between different joint types, 10 different joint types were simulated. Additionally, the effect of different joint types on behavior of a lining ring was investigated. The validity of the peridynamic simulation was tested by comparing results obtained in this paper against the results obtained in a study performed by Hordijk and Gijsbers. Observations of the results demonstrate that in a flat joint, the expanding of joint height increased the rotation stiffness of the joint in the linear branch, and accordingly, the ultimate bending moment of the joint increased. In the ring model, it was observed that the expanding of joint height led to the decreased of ring displacement and stress concentration in the joint. Whenever there were full surface contacts (contact two segment in total cross section) in the joints, the rotation stiffness of the joints in the linear branch became equal, and, as a result, the displacement in the ring model was the same in all joint types. In addition, it was observed that using a convex joint in the ring model increases the displacement of the ring. The ultimate bending moment of bolted joints was higher than that of joints without bolts, especially in the case of a negative moment.     

Impact of model complexity and multi-scale data integration on the estimation of hydrogeological parameters in a dual-porosity aquifer

This study investigates the impact of model complexity and multi-scale prior hydrogeological data on the interpretation of pumping test data in a dual-porosity aquifer (the Chalk aquifer in England, UK). In order to characterize the hydrogeological properties, different approaches ranging from a traditional analytical solution (Theis approach) to more sophisticated numerical models with automatically calibrated input parameters are applied. Comparisons of results from the different approaches show that neither traditional analytical solutions nor a numerical model assuming a homogenous and isotropic aquifer can adequately explain the observed drawdowns. A better reproduction of the observed drawdowns in all seven monitoring locations is instead achieved when medium and local-scale prior information about the vertical hydraulic conductivity (K) distribution is used to constrain the model calibration process. In particular, the integration of medium-scale vertical K variations based on flowmeter measurements lead to an improvement in the goodness-of-fit of the simulated drawdowns of about 30%. Further improvements (up to 70%) were observed when a simple upscaling approach was used to integrate small-scale K data to constrain the automatic calibration process of the numerical model. Although the analysis focuses on a specific case study, these results provide insights about the representativeness of the estimates of hydrogeological properties based on different interpretations of pumping test data, and promote the integration of multi-scale data for the characterization of heterogeneous aquifers in complex hydrogeological settings.     

A 48-kyr-long slip rate history for the Jordan Valley segment of the Dead Sea Fault

We investigate the late Quaternary active deformation along the Jordan Valley segment of the left-lateral Dead Sea Fault and provide new insights on the behaviour of major continental faults. The 110-km-long fault segment shows systematic offsets of drainage systems surveyed at three sites along its southern section. The isotopic dating of six paleoclimatic events yields a precise chronology for the onset of six generations of gully incisions at 47.5 ka BP, 37.5 ka BP, 13 ka BP, 9 ka BP, 7 ka BP, and 5 ka BP. Additionally, detailed mapping and reconstructions provide cumulative displacements for 20 dated incisions along the fault trace. The individual amounts of cumulative slip consistently fall into six distinct classes. This yields: i) an average constant slip rate of 4.7 to 5.1 mm/yr for the last 47.5 kyr and ii) a variable slip rate ranging from 3.5 mm/yr to 11 mm/yr over 2-kyr- to 24-kyr-long intervals. Taking into account that the last large earthquake occurred in AD 1033, we infer 3.5 to 5 m of present-day slip deficit which corresponds to a Mw  7.4 earthquake along the Jordan Valley fault segment. The timing of cumulative offsets reveals slip rate variations critical to our understanding of the slip deficit and seismic cycle along major continental faults.     

Hillslope run‐off thresholds with shrink–swell clay soils

Irrigation experiments on 12 instrumented field plots were used to assess the impact of dynamic soil crack networks on infiltration and run‐off. During applications of intensity similar to a heavy rainstorm, water was seen being preferentially delivered within the soil profile. However, run‐off was not observed until soil water content of the profile reached field capacity, and the apertures of surface‐connected cracks had closed >60%. Electrical resistivity measurements suggested that subsurface cracks persisted and enhanced lateral transport, even in wet conditions. Likewise, single‐ring infiltration measurements taken before and after irrigation indicated that infiltration remained an important component of the water budget at high soil water content values, despite apparent surface sealing. Overall, although the wetting and sealing of the soil profile showed considerable complexity, an emergent property at the hillslope scale was observed: all of the plots demonstrated a strikingly similar threshold run‐off response to the cumulative precipitation amount. Copyright © 2014 John Wiley & Sons, Ltd.     

Grain Dust as an Energy and Food Resource

Grain dust is a by-product produced in large quantities from grain storage and milling facilities but as of yet is treated as waste locally and regionally. Based on the conviction that material properties determination is a necessary first step for the efficient handling, processing, and use of materials, this work was initiated with the purpose of characterizing grain dust in terms of its physicochemical and thermal properties. Grain dust as a special waste material is a complex, dry, grey powder, composed mainly of grain chips, soil, whole wheat and barley seeds, and straw. The material was found to have a bulk density of 362 kg/m³, specific heat, thermal conductivity, and gross calorific value were 1540 J/kg K, 0.27 W/m K, and 4120 kJ/kg, respectively. Nutritional composition showed low concentrations of protein, and ether extract, and high concentrations of carbohydrates, ash, and crude fiber. Mineral analysis showed that Ca, Fe, and K were available in significant amounts ranging from 30 to 135 ppm. The as-received material is dry enough to be stored very safely and burned for energy production in either its loose form or as pellets. Moreover, adjustments to the ash content and C:N ratio of the material deems it a promising candidate as an animal feed and as a substrate for composting and biogasification.     

Data-Worth Assessment for a Three-Dimensional Optimal Design in Nonlinear Groundwater Systems

Groundwater model predictions are often uncertain due to inherent uncertainties in model input data. Monitored field data are commonly used to assess the performance of a model and reduce its prediction uncertainty. Given the high cost of data collection, it is imperative to identify the minimum number of required observation wells and to define the optimal locations of sampling points in space and depth. This study proposes a design methodology to optimize the number and location of additional observation wells that will effectively measure multiple hydrogeological parameters at different depths. For this purpose, we incorporated Bayesian model averaging and genetic algorithms into a linear data-worth analysis in order to conduct a three-dimensional location search for new sampling locations. We evaluated the methodology by applying it along a heterogeneous coastal aquifer with limited hydrogeological data that is experiencing salt water intrusion (SWI). The aim of the model was to identify the best locations for sampling head and salinity data, while reducing uncertainty when predicting multiple variables of SWI. The resulting optimal locations for new observation wells varied with the defined design constraints. The optimal design (OD) depended on the ratio of the start-up cost of the monitoring program and the installation cost of the first observation well. The proposed methodology can contribute toward reducing the uncertainties associated with predicting multiple variables in a groundwater system.     

Access tunnel convergence prediction in longwall coal mining

Summary The paper describes theoretical andin situ studies of tunnel deformation in longwall coal mining. It develops a method to predict tunnel convergence profiles from the faceline in longwall mining. The method accounts for the effect of panel width, extracted seam height, deformation moduli of the goaf material and coal pillar, depth of cover,in situ structural defects, tunnel shape and tunnel size in addition to the strength characteristics of surrounding strata. The analytical technique has been validated by reference toin-situ deformation measurements in 26 face-access tunnels in Cape Breton Coalfield mines. Based on this method a series of vertical convergence profiles for different depths and extracted panel widths have been presented.     

Stability Analysis of Rock Slopes Against Block-Flexure Toppling Failure

Block-flexure is the most common type of toppling failure in rock slopes. In this case, some rock blocks fail due to tensile bending stresses and some overturn under their own weights. In this paper, first, a literature review of toppling failures is summarized. Then, a theoretical model is proposed for rock slopes with a potential for block-flexure toppling instability. Next, a new analytical approach is presented for the stability analysis of such slopes. Finally, a special computer code is developed for a quick stability assessment of the failures based on the proposed method. This code receives the rock slope parameters from the user as the input data and predicts its stability, along with the corresponding factor of safety against the failure, as the output. In addition, two case studies are used for practical verification of the proposed approach and the corresponding computer code as well.     

Stability Analysis and the Stabilisation of Flexural Toppling Failure

Flexural toppling is a mode of failure that may occur in a wide range of layered rock strata in both rock slopes and large underground excavations. Whenever rock mass is composed of a set of parallel discontinuities dipping steeply against the excavated face plane, the rock mass will have the potential of flexural toppling failure as well. In such cases, the rock mass behaves like inclined superimposed cantilever beams that bend under their own weight while transferring the load to the underlying strata. If the bending stress exceeds the rock column’s tensile strength, flexural toppling failure will be initiated. Since the rock columns are “statically indeterminate,” thus, their factors of safety may not be determined solely by equations of equilibrium. The paper describes an analytical model with a sequence of inclined superimposed cantilever rock columns with a potential of flexural topping failure. The model is based on the principle of compatibility equations and leads to a new method by which the magnitudes and points of application of intercolumn forces are determined. On the basis of the proposed model, a safety factor for each rock column can be computed independently. Hence, every rock column will have a unique factor of safety. The least factor of safety that exists in any rock column is selected as the rock mass representative safety factor based on which simple equations are proposed for a conservative rock mass stability analysis and design. As a result, some new relations are established in order to design the length, cross-sectional area and pattern of fully grouted rock bolts for the stabilisation of such rock mass. Finally, the newly proposed equations are compared with the results of existing experimental flexural toppling failure models (base friction and centrifuge tests) for further verification.