CQK-50型车载化钻机的研制

在分析研究小型地质车载钻机的形式、功能与特点的基础上，提出了钻机车载化的新思路。根据地质调查工作现状，结合国内现有小型地质取样钻机，研制了CQK-50型全液压多功能车载取样钻机，并在野外物化探遥感异常验证钻探中取得了良好效果。     

我国地质找矿取心（样）钻探设备现状及提高效能的分析研究

概述了我国地质找矿钻探市场现状及前景，分析研究了地质取样钻探传统的立轴钻机及全液压动力头钻机的优缺点及综合效能，针对国家提出加强地质工作的形势及中国的实际状况，提出了完善和改进我国现有钻探设备、提高我国地质找矿取样钻探效率、降低能耗及成本的观点及建议。     

冲击凿岩钎杆的瞬态动力学分析

以ANSYS为平台，按照真实工作状态对凿岩钎杆进行了瞬态动力学分析，并对不同活塞形状下分析结果数据进行了比较，为冲击凿岩系统设计提供了理论依据。     

泥晶灰岩地层孔壁坍塌掉块现象及处理

在灰岩地区钻探施工过程中，常见孔壁坍塌、掉块现象，尤其在含泥晶灰岩地层分布区钻进过程中，这种现象尤为突出，轻则影响钻探施工效率，重则造成钻探孔内事故。针对孔内坍塌、掉块现象的征兆及特点，提出了相对应的处理办法。     

PDC钻头在寺河煤矿瓦斯预抽放钻井中的应用

在寺河矿区一期瓦斯地面预抽放钻井施工中，使用传统的镶齿三牙轮钻头钻进，钻进速度低，仅为2.0m／h，且井斜不易控制、钻头寿命短、成本较高。通过对寺河煤矿地层特征的分析，在二期工程施工中，9#煤以上地层优选六翼内凹式PDC钻头钻进，采取一定技术措施并合理调整钻压、转速及泵量等钻进参数，钻速可达7．0m/h，井斜也得到有效控制，降低了钻井成本。     

Monitoring of Over Cutting Area and Lubrication Distribution in a Large Slurry Pipe Jacking Operation

Slurry pipe jacking was firmly established as a special method for the non-disruptive construction of the underground pipelines of sewage systems. Pipe jacking, in its traditional form, has occasionally been used for short railways, roads, rivers, and other projects. Basically the system involves the pushing or thrusting of concrete pipes into the ground by a number of jacks. In slurry pipe jacking, during the pushing process, mud slurry and lubricant are injected into the face and the over cutting area that is between the concrete pipes and the surrounding soil. Next, the slurry fills voids and the soil stabilizes due to the created slurry cake around the pipes. Fillings also reduce the jacking force or thrust during operation. When the drivage and pushing processes are finished, a mortar injection into the over cutting area is carried out in order to maintain permanent stability of the surrounding soil and the over cutting area. Successful lubrication around the pipes is extremely important in a large diameter slurry pipe jacking operation. Control of lubrication and gaps between pipes and soil can prevent hazards such as surface settlement and increases in thrust. Also, to find voids around the pipes after the jacking process, in order to inject mortar for permanent stabilizing, an investigation around the pipes is necessary. To meet these aims, this paper is concerned with the utilization of known methods such as the GPR (Ground Penetrating Radar) system and borehole camera to maintain control of the over cutting area and lubricant distribution around the pipes during a site investigation. From this point of view, experiments were carried out during a tunnel construction using one of the largest cases of slurry pipe jacking in Fujisawa city, Japan. The advantages and disadvantages of each system were clarified during the tests.     

非等截面桩超声波成孔质量检测

分析了非等截面超声波成孔质量检测的几个主要影响因素,给出了相应得改进措施。用工程实例说明超声波反射技术是一种保证非等截面桩成孔质量和成桩质量必不可少的检测方法。     

利用钻孔超声成像的图像特征进行岩石风化程度分类

钻孔超声成像方法能精确地反映井壁的光滑情况, 进而判断岩石的风化发育程度, 确定风化层的厚度。阐述了钻孔超声成像的走时和振幅图像特征, 给出了1个在香港地区的应用实例。     

中国大陆科学钻探主孔声发射法现今地应力状态的确定

对中国大陆科学钻探主孔的岩心进行了声发射测量,确定了301～1531m深度的最大主应力。并与钻孔崩落法(深度1269～1655m)测量结果进行了对比,结果表明,声发射测量所得测值基本上落在钻孔崩落法测值的趋势线上,两种方法所得结果一致,说明测量结果可信。测量结果表明科学钻探主孔地应力大小随深度增加,在浅部301m最大主应力为13.4MPa,在深部1655m为55.2MPa。随深度的增加率为0.0279MPa/m。最大主应力方向为N54°±3.3°E,且方向不随深度变化。     

襄樊汉江四桥大口径灌注桩成孔施工实践

介绍了使用泥浆护壁气举反循环回转钻进工艺进行襄樊汉江四桥大口径嵌岩桩的施工实践。施工中采用下置双护简隔离卵石层，合理选用钻头类型(卵砾石层采用五翼合金刮刀钻头，基岩采用球齿滚刀钻头)和钻进参数(混合器沉没深度，尾管长度，孔内空气流量与压力)，摸索与总结出一套复杂地层成孔施工经验。