Further discussion on the intercomparison of the trace metal concentrations and particle size of fluvial sediment recovered from two centrifuge systems

A single large volume water sample taken at the mouth of the Upper Rhone River on Lake Geneva was processed directly in parallel through two continuous flow centrifuges, a Westphalia and an Alfa-Laval. Sediment was recovered from the Westphalia, and separately from the bowl and brass core of the Alfa-Laval. The three sediment samples were analyzed for particle size and the following elements: Zn, Cu, Mn, Cr, P, Co, B, V, Be, Sr, Na, Pb, Ni, Ba, Fe, Ca, and Mg. Results indicate that the particle size recovery of both machines is similar when sediment from the brass core and bowl of the Alfa-Laval are combined, and that the recovery for all elements other than Cu, V, B, and Pb are the same when the particle size differences are taken into account. Sediment from the Alfa-Laval brass core is clearly contaminated by Cu, B and is also elevated in V and Pb but not to a significant extent. The sediment recovered from the bowl of the Alfa-Laval is contaminated only with Cu, with a 10 ppm increase over the 52 ppm recovered in the Westphalia sediment. Operating procedures involve the discarding of the brass core sediment and the mixing of the Alfa-Laval bowl sediment with that from the Westphalia. The consequent increase in Cu is estimated at less than 5 ppm or within the confidence level of the analysis. These procedures are recommended to all operators of non modified Alfa-Laval units.     

Particle trajectories of nonlinear gravity waves in deep water

The paper presents a numerical method for calculating the particle trajectories of nonlinear gravity waves in deep water. Particle trajectories, mass-transport velocity and Lagrangian wave period can be accurately determined by the proposed method. The high success rate of the proposed method is examined by comparing the present results with those of (a) Longuet-Higgins, M.S., 1986, 1987. Eulerian and Lagrangian aspects of surface waves. Journal of Fluid Mechanics 173, 683-707 and (b) Lagrangian moments and mass transport in Stokes waves. Journal of Fluid Mechanics 179, 547-555. It is shown that the dimensionless mass-transport velocity can exceed 10% for large waves, and the Lagrangian wave period is much larger than the Eulerian wave period for large waves.     

Sheath effects on DEMETER ion drift measurements

The “Instrument d’Analyse du Plasma” on DEMETER includes an ion drift meter used to measure the direction of the incoming ram plasma ( [Berthelier et al., 2006a] and [Berthelier et al., 2006b]). Given the velocity of the satellite, and expected flow velocities of plasma along DEMETER's orbit, it is estimated that at mid latitudes, the direction of incident plasma as measured by IAP should be within approximately 2° of the ram direction. Yet, significantly larger angular deviations are measured routinely. An important assumption made in the interpretation of onboard instruments, such as IAP, is that neither the spacecraft nor the instrument significantly perturb the plasma that is being measured. In view of the large observed angular deviations, this paper examines the possible effect of the electrostatic sheath surrounding IAP. This is done with the 3D PIC simulation code PTetra. The model uses a full 3D particle in cell code with unstructured tetrahedral mesh capable of accurately representing the satellite geometry. The mesh is also adaptive so as to provide a fine spatial resolution in the vicinity of the particle sensor where it is needed, and a coarse resolution in regions where plasma parameters vary over a longer scale length. Calculation results show that while particle deflection associated with the electrostatic sheath near IAP can account for appreciable angular deflections for representative ionospheric plasmas, they are typically smaller than the ones observed. Additionally, the model is unable to reproduce the latitudinal dependence of the observed large deflection angles. It is concluded that sheath effects may cause appreciable distortions on the IAP type of ion flow meter instruments, and on other particle sensors in general. The larger observed deviations and their latitudinal dependence, however, must be attributable to other physical processes not accounted for in the model.     

基于图像测速的波浪破碎两相速度场测量方案探讨

针对波浪破碎试验中气泡区速度与水体速度无法同时测量的难题,基于实验室条件,搭建了粒子图像测速（PIV）和气泡图像测速（BIV）系统,采用声学多普勒测速仪（ADV）对PIV测量精度和不同场景下BIV测量精度进行了细致的验证,并设计多种试验方案以期实现BIV与PIV的同步耦合测量。试验结果表明,7W激光+后置灯的优化照明方案,其耦合测量的气泡区速度代表参数与标准BIV照明方案的结果误差小于5%,且耦合测量的气泡区下方水质点的速度曲线与标准PIV测量结果吻合,表明该改进方案满足PIV与BIV耦合测量的条件。本文实现的PIV与BIV耦合测量有利于优化测量和分析工作,减小破碎波浪重复生成的影响,有利于提高测量精度,为大范围波浪破碎速度场的快速测量提供了新的方案。     

广西寒露风开始期短期气候预测方法研究

利用1951-2013年广西90个气象观测站气温资料、国家气候中心74项指数和美国National Oceanic and Atmospheric Administration（NOAA）的Climate Prediction Center（CPC）60项指数以及海温和陆地雪盖资料、美国国家冰雪研究中心（NSIDC）的两极海冰资料,使用相关分析方法得到广西寒露风开始期气候影响因子,利用逐步回归和神经网络方法进行寒露风开始期的预测。结果表明：寒露风开始期与前一年9-10月北极海冰面积、当年3月南极海冰面积、前一年6月欧亚雪盖、当年5月北美雪盖、北半球雪盖的相关显著。与前一年9月北半球极涡面积指数、前一年10月亚洲区极涡面积指数、前一年3月热带印度洋海温偶极子等指数相关显著。粒子群-神经网络方法预测误差低于逐步回归方法,预报能力有明显提高。     

岩石颗粒破碎的尺寸效应

固体颗粒破碎强度的尺寸效应是一种普遍存在的现象,冰块、岩石颗粒、陶瓷和混凝土块等的破碎强度都表现出随颗粒直径增加而减小的现象,分形模型为解释固体颗粒破碎强度的尺寸效应提供了可行的方法。本文采用Steacy和Sammis分形模型模拟了岩石颗粒压碎特征,分析岩石颗粒破碎后的颗粒分布规律,给出颗粒破碎分维的确定方法,建立颗粒压碎强度与粒径的理论关系,颗粒破碎强度与颗粒粒径的关系用分维D表示为fdD-3。已有的颗粒破碎分布的数据表明,岩石颗粒破碎的分维大约为2.50～2.60,颗粒破碎强度符合用分维表示的尺寸效应。     

Pore orientation of granular materials during biaxial compression

The local pore spaces in granular materials tend to be aligned parallel to the major principal stress direction upon particle mobilization. Manifestation of this response has been numerically validated in our previous studies with the aid of discrete element method modeling and image processing techniques during creep and shearing. We now extend the modeling of pore geometry, constructed with spherical particles, to assemblies of particle clumps. Two-dimensional simulations are performed for both loose and dense assemblies of spherical particles and particle clumps. Each particle packing is bound by rigid or flexible walls and subjected to biaxial compression and the particle mobilization effect on the evolution of pore orientation is explored. Randomly shaped pores surrounded by adjacent particles are geometrically quantified by Delaunay tessellation and fitted with ellipses. Results show that localization is apparent in dense assemblies, in particular for clumped particle packing, while loose assemblies exhibit diffusive failure. Small pores within well-defined shear bands tend to align either parallel to the direction of the shear band or perpendicular to the major principal stress. On the other hand, small pores within the blocks and large pores have a tendency to become elongate towards the major principal stress direction. This study reveals for the first time that pore orientation is dependent upon particle shape, pore size, and assembly conditions on the pore and global scales.     

基于颗粒阻尼器的多鼓型古柱抗震性能研究

为保护地震作用下历史遗迹帕特农神庙多鼓石柱,提出将破损的石鼓替换为填充颗粒的空鼓,以减轻多鼓石柱动力响应。本文基于PFC3D与FLAC3D软件,实现了离散-有限耦合作用,模拟了附有颗粒阻尼器帕特农神庙多鼓型石柱,研究了颗粒阻尼器对帕特农神庙石柱的减震效果,并分析地震强度、频率、阻尼器位置等因素对减震效果的影响。研究结果表明,将颗粒阻尼器替换破损的空鼓,PFC3D与FLAC3D耦合计算结果与试验结果基本一致,减震效果显著,说明耦合分析方法研究颗粒阻尼器抗震性能具有较高的可靠性;地震强度不同时,分层颗粒阻尼器仍可较好地耗散能量;颗粒阻尼器对结构的减震性能受激励频率的影响显著,频率越高,减震效果越好;颗粒阻尼器布置在古柱中上部减震效果优于布置在古柱下部。     

Particle mechanics modeling of creep behavior of rockfill materials under dry and wet conditions

Rockfill is an important construction material for infrastructure engineering, such as dams, railways and airport foundations, which display a long-term post-construction settlement. However, the main mechanisms for rockfill creep and weathering influence still remain poorly understood. Particle mechanics method is used to understand the rockfill creep process under dry and wet conditions. Different bond-aging models and wetting models that represent different degradation and weakening mechanisms are compared, in order to clarify the principle and secondary mechanisms for rockfill creep and weathering influence. The results show that rockfill aggregate breakage in terms of angularity abrasion is the main source for rockfill creep under dry state. Wetting can induce additional strain mainly due to the reduction of contact friction coefficient, i.e. lubrication, and the bond strength reduction just plays a secondary role in producing additional strain. The earlier the wetting occurs during rockfill creep, the more rapidly the rockfill becomes stable. The wetting–drying cycles can induce strain evolution in a ‘stepped’ way, which is in agreement with experimental observation. The practical implications from the modeling and the outstanding issues in this study are also discussed.