双频BDS实时精密单点定位算法和精度分析

为了对BDS实时精密单点定位性能进行评估,该文提出了一种适用于BDS系统的实时精密单点定位算法。采用无电离组合模型作为双频实时精密单点定位的数学模型,采用电离层残差法和Melbourne-Wübbena组合实时探测相位周跳,进而单历元实时估计坐标、模糊度等参数,实现了BDS双频实时精密单点定位算法。基于此算法,采用轨道钟差产品和采样间隔为1s的观测数据,模拟实时BDS双频精密单点定位算法,并评估其定位精度。实验结果表明:BDS双频实时定位的平面精度和三维精度均为0.2m左右。     

Late-Quaternary Slip Rate and Seismic Activity of the Xianshuihe Fault Zone in Southwest China

The Xianshuihe fault zone is a seismo-genetic fault zone of left-lateral slip in Southwest China. Since 1725, a total of 59 Ms ≥ 5.0 earthquakes have occurred along this fault zone, including 18 Ms 6.0–6.9 and eight Ms ≥ 7.0 earthquakes. The seismic risk of the Xianshuihe fault zone is a large and realistic threat to the western Sichuan economic corridor. Based on previous studies, we carried out field geological survey and remote sensing interpretation in the fault zone. In addition, geophysical surveys, trenching and age-dating were conducted in the key parts to better understand the geometry, spatial distribution and activity of the fault zone. We infer to divide the fault zone into two parts: the northwest part and the southeast part, with total eight segments. Their Late Quaternary slip rates vary in a range of 11.5 mm/a –(3±1) mm/a. The seismic activities of the Xianshuihe fault zone are frequent and strong, periodical, and reoccurred. Combining the spatial and temporal distribution of the historical earthquakes, the seismic hazard of the Xianshuihe fault zone has been predicted by using the relationship between magnitude and frequency of earthquakes caused by different fault segments. The prediction results show that the segment between Daofu and Qianning has a possibility of Ms ≥ 7.0 earthquakes, while the segment between Shimian and Luding is likely to have earthquakes of about Ms 7.0. It is suggested to establish a GPS or In SAR-based real-time monitoring network of surface displacement to cover the Xianshuihe fault zone, and an early warning system of earthquakes and post seismic geohazards to cover the major residential areas.     

从同震和震后形变分析1668年M8.5级郯城地震对周边地震活动性的影响

以山东郯城1668年大地震为例,以前人地表地质调查结果为约束,利用弹性位错理论初步获取了该地震的同震破裂模型;在此基础上,基于粘弹性分层模型分析了该地震的同震和震后形变,同时以主震断层为接收断层计算了库仑应力分布,进一步讨论了地幔不同粘滞性系数对地表形变和库仑应力变化的影响。计算结果显示,该地震是一个右旋走滑为主兼有一定逆冲性质的地震,其同震位移巨大,能量释放较彻底;同震破裂造成震中郯城县西北、东北和南部部分断层库仑应力增加,而震后形变使得这些断层库仑应力进一步增加,在单县、宿迁和日照等地,地震后350 a库仑应力变化量达到+1bar-+1MPa量级;地幔粘滞性系数不同,形变量和库仑应力变化达到稳定的时间不同,但最终趋于稳定的数值基本一致。     

走滑断裂古地震探槽选址范例

探槽选址直接决定了古地震研究的质量,且理想探槽位置具有稀缺性。在收集82篇国内外走滑断裂古地震研究论文的基础上,分析了长序列古地震探槽选址和同震位移探槽选址的构造地貌共性特征。长序列古地震探槽一般布设在断塞塘、拉分盆地、小型湖盆、闸门脊汇水一侧及比较平缓的冲洪积扇或大型冲洪积扇末端等地貌位置。这些地貌位置的共同特征是位于连续的、较高沉积速率的沉积环境,且通常富集14C测年物质。在探槽选址的过程中,不仅要对现今沉积环境,也要对其古地理环境进行评价。然而以发掘古地震同震位移为目的的探槽选址则不同,成功的研究点往往较频繁发生侵蚀和下切事件,其中冲沟是最常见的地貌标志。探槽布设以垂直和平行探槽为主,采取逐次掘进或相间平行排列的方式开挖。由于理想探槽位置的稀缺性,所以在这些优质的探槽点一定要开展长期详细地深入研究,最大限度获得古地震事件的长序列,同时也要注意新技术和新方法的应用。     

Neotectonics of the Kharaulakh sector of the Laptev Shelf

Seismotectonic deformation and crustal stress pattern have been studied comprehensively in major seismogenic structures of the Kharaulakh sector of the Verkhoyansk fold system and adjacent parts of the Chersky seismotectonic zone. The study focuses on neotectonic structures, deep structure, and systems of active faults, as well as tectonic stress fields inferred by tectonophysical analysis of Late Cenozoic faults and folds. The results, along with geological and geophysical data, reveal main strain directions and structural patterns of crustal stress and strain in the Arctic segment of the Eurasia-North America plate boundary. The area is a junction of mid-ocean and continental structures evolving in a mixed setting of extension, compression, and their various combinations. The rotation pole of the two plates is presumably located near Buor-Khaya Bay. In this case, extension is expected to act currently upon the neotectonic structures north of the bay and compression to control those in the south and southeast. This inference is consistent with the identified zoning of stress and strain in the Kharaulakh sector.     

孔隙性砂岩中单条变形带与簇状变形带的特征与区别——以远安地堑上白垩统红花套组中变形带为例

孔隙性砂岩中的变形带研究近年来取得长足进展,但有关单条变形带与簇状变形带如何区分和界定仍是一个较模糊的问题。本文以远安地堑上白垩统红花套组高孔砂岩中发育的剪切增强压实带和压实剪切带为例,对单条及簇状变形带的特征和区别做出系统分析。研究表明,虽然单条变形带的长度、宽度、错断位移、凸起高度等均明显小于簇状变形带,但是不同运动学成因的变形带宏观特征、微观结构不同,因此不能单纯以规模大小区分二者,需要结合带密度将簇状变形带与变形带列、网格构造等相区分,还需要结合其微观结构特征进行准确鉴定。单条及簇状剪切增强压实带特征类似,均不具核心碎裂带,颗粒主要为中等破碎,多表现为多个不连续分布的碎裂核。簇状剪切增强压实带内部的非均质性更强。单条压实剪切带具有核心碎裂带,依剪切力大小不同,其核心碎裂带内颗粒粉碎程度及边缘过渡带宽度不同,常伴随微小剪切缝痕迹。簇状压实剪切带在镜下可清晰识别出不同的核心碎裂带、带间区域及微小剪切缝,可见S—C组构和断续分布的滑动面。单条及簇状变形带的发育会不同程度地改变储层的物性并可能会对油气运移和开采产生影响。     

基于深反射地震剖面的沂沭断裂带岩石圈精细结构

为揭示沂沭断裂带深部结构及发生—发展过程,查清断裂切割深度及对岩石圈地幔的破坏,探讨沂沭断裂带的构造组合样式、运动方式、地壳稳定性及其对资源环境的约束作用,研究团队于2019年在沂沭断裂带南段沂南—莒县附近布设了一条长约60 km的深反射地震剖面,系统采集了沂沭断裂带和两侧地块的地震数据,对沂沭断裂带深部岩石圈精细结构进行了解剖.结果显示,该区岩石圈结构在横向上表现为以沂沭断裂带为界的块状结构特征,地壳厚度约30.8～39.5 km;莫霍面总体呈西浅东深态势,并被西倾的沂水—汤头断裂(F2)和昌邑—大店断裂(F4)错断,垂直落差达10.5 km.与浅部"两堑夹一垒"的构造组合样式不同的是,沂沭断裂带在深部剖面上表现为由沂水—汤头断裂(F2)和昌邑—大店断裂(F4)向上延伸与分叉散开的多条断裂组成"双枝状"构造组合样式.断裂带内被断层切割的界面反射波多呈向上的拱弧形,其构造形迹具有伸展、挤压和走滑并存的特征,推断这些界面为层间滑脱构造,它们指示了沂沭断裂带"多层滑移"构造运动方式.该断裂带不仅切穿了近地表、壳内地质界面,F2、F4断裂还向下切割莫霍面,深入岩石圈地幔,是深达地幔的深大断裂构造带,为地幔热物质的上涌提供了通道,对中生代的岩浆活动和内生成矿具有控制作用.地震剖面西端的铜井金矿成矿与沿F2断裂上侵的铜井杂岩体关系密切;剖面东端的火山机构保存完整,没有明显构造破坏痕迹,据此认为沂沭断裂带左行走滑主要发生在早白垩世青山期以前,其后水平滑移量应不大.从区域地质分布及地震反演结果看,昌邑—大店断裂(F4)明显将山东省分割为鲁西和鲁东两个地质构造单元,因此将其作为区域地质构造分界线是合理的.本项研究结果进一步加深了沂沭断裂带深、浅部结构的认识,为分析研究沂沭断裂带的深部过程和浅部构造响应及对资源环境的影响提供了资料约束.     

1948年川西理塘 M7. 3地震地表破裂特征及Riedel剪切构造分析

1948年川西理塘M7. 3地震是川滇菱形块体内部近一个世纪以来发生的震级最大的走滑型地震。在对此次同震地表破裂进行详细调查基础上,利用差分GPS对同震地表破裂带进行了精确测量与统计分析。结果揭示该地表破裂的现存长度为36 km,北端始于无量河以北,往东南沿藏坝盆地北东缘、德巫盆地东南缘,延伸至德巫乡北,分为南、北两段,而在交德附近存在约3 km长的地表破裂空区。对同震地表破裂的线密度和同震水平位错量进行分段统计后揭示,此次地震的宏观震中应位于德巫盆地中部交德东南约4~5 km处。对理塘同震地表破裂的Riedel剪切分析结果指示,该破裂带主要由R剪切组成,以发育雁列状排列的挤压鼓包(Push- up)为主要特征,伴有少量R′剪切与T裂缝,缺少P型与X型剪切。其中R剪切占95%以上,其在藏坝段(北段)的优势方向为318°,德巫段(南段)为315°,整条地表破裂带的R剪切平均方向为316°。同时发现,此次地震形成的雁列状挤压鼓包主要以平缓的“弧形”为主,这与1981年道孚MS 6. 9地震和2010年玉树MS 7. 1地震地表破裂带中出现大量反“S”形挤压鼓包有所不同,推断与走滑断裂滑动速率密切相关。沿强滑动速率走滑断层地震破裂带的Riedel剪切发育会更为完善,挤压鼓包也更发育,易形成反“S”形,反之则以平缓的“弧形”为特征。综合分析认为,1948年理塘同震地表破裂带的展布主要受藏坝盆地与德巫盆地控制,而且藏坝段(北段)与德巫段(南段)的R剪切方向存在偏差,这可能与两个拉分盆地的发育程度有关。     

Study of bond stress–slip relationship and radial dilation in prestressed concrete

This paper presents two test procedures for evaluating the bond stress–slip and the slip–radial dilation relationships when the prestressing force is transmitted by releasing the steel (wire or strand) in precast prestressed elements. The bond stress–slip relationship is obtained with short length specimens, to guarantee uniform bond stress, for three depths of the wire indentation (shallow, medium and deep). An analytical model for bond stress–slip relationship is proposed and compared with the experimental results. The model is also compared with the experimental results of other researchers. Since numerical models for studying bond‐splitting problems in prestressed concrete require experimental data about dilatancy angle (radial dilation), a test procedure is proposed to evaluate these parameters. The obtained values of the radial dilation are compared with the prior estimated by numerical modelling and good agreement is reached. Copyright © 2012 John Wiley & Sons, Ltd.     

Frictional heat generation and seismic radiation in a foam rubber model of earthquakes

Results from a study of stick-slip particle motion at the interface between two stressed foam rubber blocks indicate that normal vibrations and interface separation are an important part of the stick-slip process in foam rubber. The dimension of the dynamic slip pulse is small compared to the dimension of the model (approximately 10 cm vs. 200 cm) consistent with the abrupt-locking slip pulse model ofBrune (1970, 1976), andHeaton (1990). A comparison of frictional heat generation between stable-sliding and stick-slip foam rubber models indicates a linear relation between the temperature increase on the fault surface (for a given distance of slip) and the driving shear force for the stable-sliding model, while for the stick-slip model there is essentially no variation in frictional heat generation with an increase in shear stress. We performed experiments to investigate the ratio of normal motion to shear motion at different levels of normal stress in the stick-slip foam rubber model. Preliminary result indicate that the normal component of the particle motion increases more rapidly with increasing normal stress than the shear component. The phenomenon of interface separation and normal vibrations may thus explain some of the most frustrating problems in earthquake mechanics, e.g., the heat flow paradox, the long-term weakness of major active faults, and anomalousP-wave radiation.