Design of 2-M to 6-M Liquid Mirror Containers

A new design is proposed for large (up to 6-m) liquid mirror containers. The design uses Kevlar, foam and aluminum, as in previous designs, but with a different configuration that makes the container lighter, stronger and more rigid. The results of finite element analysis are presented, consisting in the deformations due to temperature changes and to weight, and in the security factor for each material when maximum constraints are applied. Tilt rigidity is also analyzed. They show that the composite material construction technique gives a good performance up to 6 m diameters. The figures and tables contained in this paper can be used as recipes to build containers having diameters between 2 and 6 m. This revised version was published online in July 2006 with corrections to the Cover Date.     

The importance of oxygen isotope provenance in relation to solute content of bulk meltwaters at Imersuaq Glacier,West Greenland

Stable oxygen isotope analysis and measurement of several dissolved cations and anions of bulk meltwater samples have provided information about the hydrochemical environment of the glacial hydrological system at Imersuaq Glacier, an outlet tongue from the Greenland ice‐sheet, West Greenland. The samples were collected at frequent intervals during the period 20–28 July 2000 in a small (<20 L s^?1) englacial meltwater outlet at the glacier margin. The results document the following findings: (i) a marked diurnal variation of δ¹⁸O is related to the composition of oxygen isotope provenances, mainly near‐marginal local superimposed ice and basal up‐sheared ice further up‐glacier; (ii) a relationship is seen between all base cations (Na⁺, K⁺, Ca²⁺, Mg²⁺), SO₄^2? and δ¹⁸O, indicating that solute acquisition is provided by solid–solution contact with the up‐sheared ice—as the relationship with Cl^? is weak the influence of seasalt‐derived solutes is small in the area; (iii) when the melt rate is high, two diurnal maxima of δ¹⁸O values and solute concentrations are measured, and it is suggested that a snow meltwater component is responsible for the second maximum of δ¹⁸O—a short residence time leads to a delayed decrease in ion concentrations. Copyright © 2003 John Wiley & Sons, Ltd.     

南极威尔克斯地SGR钻孔处雪冰转化过程中的密度变化特征

本文着重描述了SGR钻孔处冰盖上的积雪在密实化过程中的特征变化,并对该过程进行了分段的和全面的回归分析.结果表明,冰盖密度随深度增大,但增长幅度随深度减小.作者提出密度变化减小度的概念.计算得出的所研究冰芯钻取点的密度变化减小度为-0.15kg/m~3·m~2,粒雪成冰前的密实速率平均值为4.08kg/m~3·a.本文得到的冰盖密度变化“临界点”与以往报道的有所不同.分析这一现象时,作者强调当积雪还在活动层时冰盖温度的影响,并以此解释密度剖面的异常变化以及离差的回升.特别指出,积雪的密度变化具有气候学意义,它在一定程度上能够反映出积雪形成及变化过程中气候变化的某些信息.本文由密度变化确定的钻孔点雪冰转化深度为50米.     

The Lower Permian Wasp Head Formation,Sydney Basin: high‐latitude,shallow marine sedimentation following the late Asselian to early Sakmarian glacial event in eastern Australia

The Lower Permian Wasp Head Formation (early to middle Sakmarian) is a ～95 m thick unit that was deposited during the transition to a non‐glacial period following the late Asselian to early Sakmarian glacial event in eastern Australia. This shallow marine, sandstone‐dominated unit can be subdivided into six facies associations. (i) The marine sediment gravity flow facies association consists of breccias and conglomerates deposited in upper shoreface water depths. (ii) Upper shoreface deposits consist of cross‐stratified, conglomeratic sandstones with an impoverished expression of the Skolithos Ichnofacies. (iii) Middle shoreface deposits consist of hummocky cross‐stratified sandstones with a trace fossil assemblage that represents the Skolithos Ichnofacies. (iv) Lower shoreface deposits are similar to middle shoreface deposits, but contain more pervasive bioturbation and a distal expression of the Skolithos Ichnofacies to a proximal expression of the Cruziana Ichnofacies. (v) Delta‐influenced, lower shoreface‐offshore transition deposits are distinguished by sparsely bioturbated carbonaceous mudstone drapes within a variety of shoreface and offshore deposits. Trace fossil assemblages represent distal expressions of the Skolithos Ichnofacies to stressed, proximal expressions of the Cruziana Ichnofacies. Impoverished trace fossil assemblages record variable and episodic environmental stresses possibly caused by fluctuations in sedimentation rates, substrate consistencies, salinity, oxygen levels, turbidity and other physio‐chemical stresses characteristic of deltaic conditions. (vi) The offshore transition‐offshore facies association consists of mudstone and admixed sandstone and mudstone with pervasive bioturbation and an archetypal to distal expression of the Cruziana Ichnofacies. The lowermost ～50 m of the formation consists of a single deepening upward cycle formed as the basin transitioned from glacioisostatic rebound following the Asselian to early Sakmarian glacial to a regime dominated by regional extensional subsidence without significant glacial influence. The upper ～45 m of the formation can be subdivided into three shallowing upward cycles (parasequences) that formed in the aftermath of rapid, possibly glacioeustatic, rises in relative sea‐level or due to autocyclic progradation patterns. The shift to a parasequence‐dominated architecture and progressive decrease in ice‐rafted debris upwards through the succession records the release from glacioisostatic rebound and amelioration of climate that accompanied the transition to broadly non‐glacial conditions.     

碱消解-高效液相色谱-电感耦合等离子体质谱法测定生物样品中的甲基汞和乙基汞

建立了碱消解-高效液相色谱-电感耦合等离子体质谱联用系统测定生物样品中甲基汞(MeHg)与乙基汞(EtHg)的分析方法。为提高灵敏度,选用微流量的PFA雾化器,在优化的检测条件下,MeHg及EtHg检出限可达到0.036μg/L和0.03μg/L;线性范围达到4个数量级,两条工作曲线线性相关系数为1。对1.78μg/L MeHg、1.65μg/L EtHg的混合标准溶液重复测定7次,色谱峰面积的相对标准偏差(RSD)分别为1.79%和1.44%。对标准物质BCR 464(金枪鱼)的分析结果表明,测定值与标准值基本吻合,但略低于标准值;甲基汞和乙基汞的加标回收率分别为85.9%和84.5%。高效液相色谱与质谱联用技术的高灵敏度和低检出限能够满足生物样品中汞形态定量分析的要求。     

Experimental solidification of anhydrous latitic and trachytic melts at different cooling rates: The role of nucleation kinetics

Two sets of cooling experiments were run at atmospheric conditions for two anhydrous starting latitic and trachytic melts: 1) five cooling rates (25, 12.5, 3, 0.5, and 0.125 °C/min) between 1300° and 800 °C, and 2) a 0.5 °C/min cooling rate from 1300 °C with quench temperatures at 1200°, 1100°, 1000° and 900 °C. Trachytic run-products are invariably glassy. Nucleation is also suppressed in the latitic run-products at the three highest cooling rates. Conversely, in the 0.5 and 0.125 °C/min runs, latites have a crystal content of  90 vol.%. The phases are: plagioclase, clinopyroxene, glass and iron-bearing oxide (in order of abundance). The variable quench temperatures, investigated by coupling experiments with Pt wire and Pt capsule sample containers in set 2, again did not produce crystallization of trachyte, whereas latitic samples are characterized by  10 vol.% of oxides, pyroxenes and plagioclase (in order of appearance), at temperature < 1000 °C. Effects of (preferential) heterogeneous nucleation on sample holders, of superheating degree, and chemical species loss during cooling are absent for both melt compositions. The difference of solidification paths between these two silicate melts can be ascribed only to their small chemical differences. In comparison with calculated equilibrium conditions all the experimental latitic and trachytic run-products revealed strong kinetic effects, interpretable in the light of the nucleation theory. The glass-forming ability (GFA) of trachyte is higher, whereas their critical cooling rate (Rc) is lower (< 0.125 °C/min), in comparison to latitic melts (Rc > 0.5 °C/min). The experimental results carried out in this study can be applied to lava flows and domes; trachytic lavas are able to flow for longer period with respect to latitic ones in a metastable condition. Glass-rich terrestrial lavas, i.e. obsidians, can be the result of sluggish nucleation kinetics due to the relative high polymerisation of evolved silicate melts.     

Magma Ascent and Crustal Accretion at Ultraslow-Spreading Ridges: Constraints from Plagioclase Ultraphyric Basalts from the Arctic Mid-Ocean Ridge

Plagioclase ultraphyric basalts (PUBs) with up to 54% plagioclasephenocrysts were dredged in the rift valley and adjacent flanksof the ultraslow-spreading Mohns and Knipovich ridges. The PUBsshow large variations in crystal morphologies and zoning. Thelarge variations suggest that single basalt samples containa mixture of plagioclase crystals that aggregated at differentlevels in the magma conduits. Resorbed crystals and repeatedreverse zones suggest that the magma reservoirs were replenishedand heated several times. Thin concentric zones with melt inclusions,and sharp reductions in the anorthite content of 3–7%,are common between the reverse zones. These zones, and skeletalcrystals with distinctly lower anorthite contents than massivecrystals, are interpreted to be the result of rapid crystalliztionduring strong undercooling. The changes between short periodsof cooling and longer periods with reheating are explained bymultiple advances of crystal-rich magma into cool regions followedby longer periods of gradual magma inflow and temperature increase.The porphyritic basalts are characterizd by more depleted andmore fractionated compositions than the aphyric basalts, withlower (La/Sm)_N, K₂O and Mg-numbers. This relationship, and theobservation that PUBs are sampled only close to segment centresalong these ridges, suggests that the PUBs formed by higherdegrees of melting and evolved in more long-lived magma reservoirs.We propose that the zoning patterns of plagioclase crystalsand crystal morphologies of these PUBs reflect the developmentand flow of magma through a stacked sill complex-like conduitsystem, whereas the aphyric equivalents represent later flowof magma through the conduit. The formation of voluminous higher-degreemelts may trigger the development of the magma conduits andexplain the generally depleted compositions of PUB magmas. KEY WORDS: basalt; mineral chemistry; MORB; magma mixing; magma chamber; major element     

Pressures of Crystallization of Icelandic Magmas

Iceland lies astride the Mid-Atlantic Ridge and was createdby seafloor spreading that began about 55 Ma. The crust is anomalouslythick (20–40 km), indicating higher melt productivityin the underlying mantle compared with normal ridge segmentsas a result of the presence of a mantle plume or upwelling centeredbeneath the northwestern edge of the Vatnajökull ice sheet.Seismic and volcanic activity is concentrated in 50 km wideneovolcanic or rift zones, which mark the subaerial Mid-AtlanticRidge, and in three flank zones. Geodetic and geophysical studiesprovide evidence for magma chambers located over a range ofdepths (1·5–21 km) in the crust, with shallow magmachambers beneath some volcanic centers (Katla, Grimsvötn,Eyjafjallajökull), and both shallow and deep chambers beneathothers (e.g. Krafla and Askja). We have compiled analyses ofbasalt glass with geochemical characteristics indicating crystallizationof ol–plag–cpx from 28 volcanic centers in the Western,Northern and Eastern rift zones as well as from the SouthernFlank Zone. Pressures of crystallization were calculated forthese glasses, and confirm that Icelandic magmas crystallizeover a wide range of pressures (0·001 to 1 GPa), equivalentto depths of 0–35 km. This range partly reflects crystallizationof melts en route to the surface, probably in dikes and conduits,after they leave intracrustal chambers. We find no evidencefor a shallow chamber beneath Katla, which probably indicatesthat the shallow chamber identified in other studies containssilica-rich magma rather than basalt. There is reasonably goodcorrelation between the depths of deep chambers (> 17 km)and geophysical estimates of Moho depth, indicating that magmaponds at the crust–mantle boundary. Shallow chambers (<7·1 km) are located in the upper crust, and probablyform at a level of neutral buoyancy. There are also discretechambers at intermediate depths (11 km beneath the rift zones),and there is strong evidence for cooling and crystallizing magmabodies or pockets throughout the middle and lower crust thatmight resemble a crystal mush. The results suggest that themiddle and lower crust is relatively hot and porous. It is suggestedthat crustal accretion occurs over a range of depths similarto those in recent models for accretionary processes at mid-oceanridges. The presence of multiple stacked chambers and hot, porouscrust suggests that magma evolution is complex and involvespolybaric crystallization, magma mixing, and assimilation. KEY WORDS: Iceland rift zones; cotectic crystallization; pressure; depth; magma chamber; volcanic glass     

Trace Element Partitioning and Accessory Phase Saturation during H2O-Saturated Melting of Basalt with Implications for Subduction Zone Chemical Fluxes

Experimental phase equilibrium and trace element partitioningdata are reported for H₂O-saturated mid-ocean ridge basalt at2·5 GPa, 750–900°C and oxygen fugacities atthe nickel–nickel oxide buffer. Garnet, omphacite andrutile are present at all temperatures. Amphibole and epidotedisappear as residual phases above 800°C; allanite appearsabove 750°C. The Na–Al-rich silicate glass presentin all run products is likely to have quenched from a supercriticalliquid. Trace element analyses of glasses demonstrate the importantcontrol exerted by residual minerals on liquid chemistry. Inaddition to garnet, which controls heavy rare earth elements(HREE) and Sc, and rutile, which controls Ti, Nb and Ta, allanitebuffers the light REE (LREE; La–Sm) contents of liquidsto relatively low levels and preferentially holds back Th relativeto U. In agreement with previous experimental and metamorphicstudies we propose that residual allanite plays a key role inselectively retaining trace elements in the slab during subduction.Experimental data and analyses of allanite-bearing volcanicrocks are used to derive a model for allanite solubility inliquids as a function of pressure, temperature, anhydrous liquidcomposition and LREE content. The large temperature dependenceof allanite solubility is very similar to that previously determinedfor monazite. Our model, fitted to 48 datapoints, retrievesLREE solubility (in ppm) to within a factor of 1· 40over a pressure range of 0–4 GPa, temperature range of700–1200°C and for liquids with anhydrous SiO₂ contentsof 50–84 wt %. This uncertainty in LREE content is equivalentto a temperature uncertainty of only ± 27°C at 1000K, indicating the potential of allanite as a geothermometer.Silicic liquids from either basaltic or sedimentary protolithswill be saturated in allanite except for Ca-poor protolithsor at very high temperatures. For conventional subduction geothermsthe low solubility of LREE (+ Th) in liquids raises questionsabout the mechanism of LREE + Th transport from slab to wedge.It is suggested either that, locally, temperatures experiencedby the slab are high enough to eliminate allanite in the residueor that substantial volumes of H₂O-rich fluids must pass throughthe mantle wedge prior to melting. The solubility of accessoryphases in fluids derived from subducted rocks can provide importantconstraints on subduction zone thermal structure. KEY WORDS: subduction; experimental petrology; allanite; solubility; supercritical liquid; eclogite     

渤海湾盆地新生界生油岩系底界面温度分布

依据渤海湾盆地2000余口测温井的地温梯度数据、地层岩性描述、分层数据以及钻井资料,计算了该盆地各生油岩系底界面的温度。统计结果表明:渤海湾盆地沙河街组大部分凹陷区地层底界面温度介于90℃至150℃,目前仍具有大量生油的温度条件,而在隆起或一些凸起地区,该地层组段温度普遍小于90℃,未能达到生油的温度指标。东营组和孔店组地层也仍具有一定的生油温度条件。研究还表明:地层温度与地层界面埋深密切相关,温度随界面埋深的增大而升高,沉积厚度大的凹陷区地层界面温度大于沉积厚度小的凸起区或斜坡地带,说明地层界面埋深是决定地温高低的主要控制因素,而地温梯度对地层界面温度的影响相对较小。