软弱地基码头的快速建造方法

文中介绍了软基快速建造码头的方法与技术。在含水量高、孔隙比大、渗透系数小、埋藏深厚、承载力与抗剪强度低、灵敏度高的软弱地基上,采用软基快速筑堤方法和鲎式硬壳堤坝技术,22 d时间完成码头建造,投入使用1 a多时间,一直未出现裂缝等问题。     

基于特征提取的目标变化检测方法研究

针对不同时相遥感影像中特定目标的变化,研究了基于特征提取的目标变化检测方法。该方法首先根据目标的几何特征进行检测与提取,然后对提取出的两目标影像进行比较,得到特定目标的变化。实验结果表明该方法对特定目标的变化检测有较好的效果。     

亚像素定位的关键问题研究

分析了控制点标志的选择与设计,采用了图像处理、Hough变换、角点与直线高精度定位算子等方法,实现了中南大学近景摄影测量二维控制场1 350个人工标志点的自动识别和亚像素定位,仿真图检测平均精度达到±0.05像素。     

4D seismic time-lapse monitoring of an active cold vent,northern Cascadia margin

Two single-channel seismic (SCS) data sets collected in 2000 and 2005 were used for a four-dimensional (4D) time-lapse analysis of an active cold vent (Bullseye Vent). The data set acquired in 2000 serves as a reference in the applied processing sequence. The 4D processing sequence utilizes time- and phase-matching, gain adjustments and shaping filters to transform the 2005 data set so that it is most comparable to the conditions under which the 2000 data were acquired. The cold vent is characterized by seismic blanking, which is a result of the presence of gas hydrate in the subsurface either within coarser-grained turbidite sands or in fractures, as well as free gas trapped in these fracture systems. The area of blanking was defined using the seismic attributes instantaneous amplitude and similarity. Several areas were identified where blanking was reduced in 2005 relative to 2000. But most of the centre of Bullseye Vent and the area around it were seen to be characterized by intensified blanking in 2005. Tracing these areas of intensified blanking through the three-dimensional (3D) seismic volume defined several apparent new flow pathways that were not seen in the 2000 data, which are interpreted as newly generated fractures/faults for upward fluid migration. Intensified blanking is interpreted as a result of new formation of gas hydrate in the subsurface along new fracture pathways. Areas with reduced blanking may be zones where formerly plugged fractures that had trapped some free gas may have been opened and free gas was liberated.     

Fast static correction methods for high-frequency multichannel marine seismic reflection data: A high-resolution seismic study of channel-levee systems on the Bengal Fan

Very high-frequency marine multichannel seismic reflection data generated by small-volume air- or waterguns allow detailed, high-resolution studies of sedimentary structures of the order of one to few metres wavelength. The high-frequency content, however, requires (1) a very exact knowledge of the source and receiver positions, and (2) the development of data processing methods which take this exact geometry into account. Static corrections are crucial for the quality of very high-frequency stacked data because static shifts caused by variations of the source and streamer depths are of the order of half to one dominant wavelength, so that they can lead to destructive interference during stacking of CDP sorted traces. As common surface-consistent residual static correction methods developed for land seismic data require fixed shot and receiver locations two simple and fast techniques have been developed for marine seismic data with moving sources and receivers to correct such static shifts. The first method – called CDP static correction method – is based on a simultaneous recording of Parasound sediment echosounder and multichannel seismic reflection data. It compares the depth information derived from the first arrivals of both data sets to calculate static correction time shifts for each seismic channel relative to the Parasound water depths. The second method – called average static correction method – utilises the fact that the streamer depth is mainly controlled by bird units, which keep the streamer in a predefined depth at certain increments but do not prevent the streamer from being slightly buoyant in-between. In case of calm weather conditions these streamer bendings mainly contribute to the overall static time shifts, whereas depth variations of the source are negligible. Hence, mean static correction time shifts are calculated for each channel by averaging the depth values determined at each geophone group position for several subsequent shots. Application of both methods to data of a high-resolution seismic survey of channel-levee systems on the Bengal Fan shows that the quality of the stacked section can be improved significantly compared to stacking results achieved without preceding static corrections. The optimised records show sedimentary features in great detail, that are not visible without static corrections. Limitations only result from the sea floor topography. The CDP static correction method generally provides more coherent reflections than the average static correction method but can only be applied in areas with rather flat sea floor, where no diffraction hyperbolae occur. In contrast, the average static correction method can also be used in regions with rough morphology, but the coherency of reflections is slightly reduced compared to the results of the CDP static correction method.     

悬浮沙激光散斑图像处理的研究

本文以统计模式识别为基础，阐述了图像处理在悬浮沙粒粒径流量中的实际应用，提出了用图像层析来确定放大系数的方法，提出了测量的准确度。     

走航测深数据的自动采集

本文介绍应用IBM微机实现走航实时水深及定位数据的自动采集系统。给出了联机系统方框图及采集、传送数据的程序流程图。并对IBM-PC/XT微机与测深仪之间的接口、数码转换和数据处理作了简要的叙述。     

自动海洋站数据接收与处理软件的功能及特点

采集设备采集数据发送到值班PC机，在无人干预的情况下接收处理软件自动对数据进行回放和进一步处理，为用户提供数据产品和服务，并提供一个界面，使用户能够了解系统的运行状况，获得相关数据和状态参数。     

SPOT遥感影像处理技术以及在青岛市海洋功能区划中的应用

青岛市海洋功能区划中，大范围采用了法国高分辨率陆地卫星SPOT-5HRG 1A级遥感数据。利用Geoimage遥感影像处理软件对数据进行了处理．包括：遥感影像的正射纠正、辐射处理和不同分辨率影像地融合等，获得了高空间分辨率和良好的光谱分辨率的遥感图像。很好的识别出青岛海岸带地区地物分布特征。为海洋功能区划底图补充了真实而丰富的信息．     

A new type of Shipboard Meteorological Satellite Receiving-processing System

INTRODUCTIONTheSMSRPSisstalledontheshipnavigatingovertheseaandreceivessatellitecloudmapsatanytimetoprovidereliablereal-timedataofmeteorologyandocean.Itisanimportantequipmentforsafeguardofshipnavigation.Chinahasthousandsofoceanicships.Butalmostallships,withonlyveryfewexception,arenotstalledbySMSRPS.Thecausesareasfollows:1.Thetechniqueisverycomplicated.2.Thedevelopmentcostisveryhigh.3.Ifweintroduceforeignequipment,thecostistooexpensive.4.Foreignequipmentanditssoftwarearecompletelyclo…