Estimation of snow ablation under a dust layer covering a wide range of albedo

Ablation processes of snow under a thin dust cover are complicated compared with those under a thick cover, mainly owing to the effects of aggregation (redistribution) of dust particles on the conditions of surface melting. Aggregation of dust particles causes the snow surface to brighten after the initial dust configuration, thus affecting the relationship between initial dust concentration and surface albedo. In order to estimate snow ablation rate under a thin dust cover, we used a composite energy balance model in which the surface albedo is taken as a measured input variable. The estimated results of snow ablation agreed reasonably well with the observation, considering the measurement errors inherited in the snow depressions. Comparison of the two cases, that is, one considering the aggregation of dust particles (observation: albedo variable) and the other without aggregation (assumption: albedo constant), showed that the ablation rates were noticeably lower on the former case. This suggests that the aggregation of dust particles induces a reduction of snow ablation. Copyright © 2002 John Wiley & Sons, Ltd.     

Spinifex-like textured metaperidotites from the Higo Metamorphic Rocks,Japan, a possible high-pressure dehydration product of antigorite serpentinite

Spinifex-like textured metaperidotites from the Higo Metamorphic Rocks (HMR), west-central Kyushu, Japan, may be formed by high-pressure dehydration of antigorite, and may indicate deep subduction of serpentinite reaching a pressure–temperature condition of 1.6 GPa and 740–750 °C. Three rock types have been identified based on mineral assemblage and rock texture: Type I (L) consisting of medium-grained (1–5 cm long) olivine + enstatite + chromite ±tremolite with secondary talc and anthophyllite that occurs in low-grade metamorphic rocks of the biotite zone, Type I (H) of coarse-grained (up to 10 cm long) olivine + enstatite (with clinoenstatite lamella) + chromite ±tremolite with secondary talc that occurs in high-grade metamorphic rocks of the garnet-cordierite zone, and Type II composed of Al-spinel + chlorite + olivine + apatite + ilmenite with minor sodic gedrite in the garnet-cordierite zone together with Type I (H). Olivines in all rock types are mostly serpentinized during exhumation. The chromite-olivine thermometer gives 560–690 °C for Type I (L) rocks, and the spinel-olivine thermometer gives 610–740 °C for Type II rocks. The peak metamorphic pressure will be higher than 1.6 GPa based on the location of the experimentally determined invariant point (P = 1.6 GPa and T = 670 °C) of antigorite + forsterite + enstatite + talc + H₂O. This estimate is consistent with the occurrence of chlorite in Type II rocks, which is stable up to 890 °C at 2.0 GPa. The spinifex-like textured metaperidotites occur as small bodies in the low P/T type gneisses, implying tectonic juxtaposition of them probably during exhumation of the HMR. Recent findings of medium pressure (0.9–1.2 GPa) granulites and gneisses from the HMR may indicate that the HMR has a deep root into the wedge mantle from which the spinifex-like textured metaperidotites have derived.     

Calibration and validation of the ocean color version-3 product from ADEOS OCTS

We present calibration and validation results of the OCTS’s ocean color version-3 product, which mainly consists of the chlorophyll-a concentration (Chl-a) and the normalized water-leaving radiance (_nL_w). First, OCTS was calibrated for the inter-detector sensitivity difference, offset, and absolute sensitivity using external calibration source. It was also vicariously calibrated using in-situ measurements for water (Chl-a and_nL_w) and atmosphere (optical thickness), which were acquired synchronously with OCTS under cloud-free conditions. Second, the product was validated using selected 17 in-situ Chl-a and 11 in-situ_nL_w measurements. We confirmed that Chl-a was estimated with an accuracy of 68% for Chl-a less than 2 mg/m³, and_nL_w from 94% (band 2) to 128% (band 4). Geometric accuracy was improved to 1.3 km. Stripes were significantly reduced by modifying the detector normalization factor as a function of input radiance.     

Correction of atmospheric effect on ADEOS/OCTS ocean color data: Algorithm description and evaluation of its performance

This paper first describes the atmospheric correction algorithm for OCTS visible band data used at NASDA/EOC. Sharing a basic structure with Gordon and Wang’s Sea WiFS algorithm, it uses 10 candidate aerosol models including the “Asian dust model” introduced in consideration of the unique feature of aerosols over the east Asian waters. Based on the observations at 670 and 865 nm bands, the algorithm selects a pair of aerosol models that account best for the observed spectral reflectances, and synthesizes the aerosol reflectance used for the atmospheric correction. Two different schemes for determining the value of the parameter for the aerosol model selection are presented and their anticipated estimation error is analyzed in terms of retrieved water reflectance at 443 nm. The results of our numerical simulation show that the standard deviation of the estimation error of the “weighted average” scheme is mostly within the permissible level of ±0.002, reducing the error by 18% on average compared to the “simple average” scheme. The paper further discusses the expected error under the old CZCS-type atmospheric correction, which assumes constant aerosol optical properties throughout the given image. Although our algorithm has a better performance than the CZCS algorithm, further analysis shows that the error induced by the assumption taken in the algorithm that the water-leaving radiance at 670 nm band is negligibly small may be large in high pigment concentration waters, indicating the necessity for future improvements.     

Improving integrity of RC beam-column joints with deficient beam rebar anchorage

In recent earthquakes in developing countries, severe damage was observed on reinforced concrete buildings. This study focuses on exterior beam-column joints with substandard beam rebar anchorage and seismic strengthening by installing wing walls. First, a series of experiments was conducted to investigate the seismic behavior of exterior joints with substandard beam rebar anchorage representing typical Bangladeshi buildings. Two 0.7-scaled exterior joint specimens were tested, and these specimens showed beam rebar anchorage failure and/or joint shear failure. Prior to strengthening of the joint, a series of pullout tests was conducted on postinstalled bonded anchors in low-strength concrete for strengthening design. Then, an experiment was performed to apply the strengthening method by wing walls to one of the exterior joint specimens to improve the integrity, and this method was intended to prevent the failure of beam rebar anchorage. The strengthening method is proposed to extend the development length of beam longitudinal bars by considering the embedment length along the wing walls. The test results verified the effectiveness and applicability of the proposed strengthening method to upgrade exterior RC beam-column joints with deficient beam rebar anchorage.     

The Ganges and Brahmaputra rivers in Bangladesh: basin denudation and sedimentation

Every year the Ganges and Brahmaputra rivers in Bangladesh transport 316 and 721 million tonnes of sediment, respectively. These high loads of suspended sediment reflect the very high rate of denudation in their drainage basins. The average mechanical denudation rate for the Ganges and Brahmaputra basins together is 365 mm 10³ yr⁻¹. However, the rate is higher in the Brahmaputra Basin than that in the Ganges Basin. Several factors, including mean trunk channel gradient, relief ratio, runoff, basin lithology and recurring earthquakes are responsible for these high denudation rates. Of the total suspended sediment load (i.e. 1037 million tonnes) transported by these rivers, only 525 million tonnes (c. 51% of the total load) are delivered to the coastal area of Bangladesh and the remaining 512 million tonnes are deposited within the lower basin, offsetting the subsidence. Of the deposited load, about 289 million tonnes (about 28% of the total load) are deposited on the floodplains of these rivers. The remaining 223 million tonnes (about 21% of the total load) are deposited within the river channels, resulting in aggradation of the channel bed at an average rate of about 3·9 cm yr⁻¹. Although the Brahmaputra transports a higher sediment load than the Ganges, the channel bed aggradation rate is much higher for the Ganges. This study also documents a wide range of interannual, seasonal and daily variation in suspended sediment transport and water discharge. Interannual variation in sediment deposition within the basin is also suggested. Copyright © 1999 John Wiley & Sons, Ltd.     

Implication of Apatite and Anhydrite for Formation of an Iron‐Oxide‐Apatite (IOA) Rare Earth Element Prospect,Benjamin River,Canada

The Benjamin River apatite prospect in northern New Brunswick, Canada, is hosted by the Late Silurian Dickie Brook plutonic complex, which is made up of intrusive units represented by monzogranite, diorite and gabbro. The IOA ores, composed mainly of apatite, augite, and magnetite at Benjamin River form pegmatitic pods and lenses in the host igneous rocks, the largest of which is 100 m long and 10–20 m wide in the diorite and gabbro units. In this study, 28 IOA ore and rock samples were collected from the diorite and gabbro units. Mineralogical observations show that the apatite–augite–magnetite ores are variable in the amounts of apatite, augite, and magnetite and are associated with minor amounts of epidote‐group minerals (allanite, REE‐rich epidote and epidte) and trace amounts of albite, titanite, ilmenite, titanomagnetite, pyrite, chlorite, calcite, and quartz. Apatite and augite grains contain small anhydrite inclusions. This suggests that the magma that crystallized apatite and augite had high oxygen fugacity. In back scattered electron (BSE) images, apatite grains in the ores have two zones of different appearance: (i) primary REE‐rich zone; and (ii) porous REE‐poor zone. The porous REE‐poor zones mainly appear in rims and/or inside of the apatite grains, in addition to the presence of apatite grains which totally consist of a porous REE‐poor apatite. This porous REE‐poor apatite is characterized by low REE (<0.84 wt%), Si (<0.28 wt%), and Cl (<0.17 wt%) contents. Epidote‐group minerals mainly occur in grain boundary between the porous REE‐poor apatite and augite. These indicate that REE leached from primary REE‐rich apatite crystallized as allanite and REE‐rich epidote. Magnetite in the ores often occurs as veinlets that cut apatite grains or as anhedral grains that replace a part of augite. These textures suggest that magnetite crystallized in the late stage. Pyrite veins occur in the ores, including a large amount of quartz and calcite veins. Pyrite veins mainly occur with quartz veins in augite. These textures indicate pyrite veins are the latest phase. Apatite–augite–magnetite ore, gabbro–quartz diorite and feldspar dike collected from the Benjamin River prospect contain dirty pure albite (Ab₉₈Or₂–Ab₁₀₀) under the microscope. The feldspar dikes mainly consist of dirty pure albite. Occurrences of the dirty pure albite suggest remarkable albitization (sodic alteration) of original plagioclase (An_25.3–An₆₀ in Pilote et al., 2012) associating with intrusion of monzogranite into gabbro and diorite. SO₄^2? bearing magma crystallized primary REE‐rich apatite, augite and anhydrite reacted with Fe in the sodic fluids, which result in oxidation of Fe²⁺ and release of S^2? into the sodic fluids. REE, Ca and Fe from primary REE‐rich apatite, augite and plagioclase altered by the sodic fluids were released into the fluids. Then Fe³⁺ in the sodic fluids precipitated as Fe oxides and epidote‐group minerals in apatite–augite–magnetite ores. Finally, residual S^2? in sodic fluids crystallized as latest pyrite veins. In conclusion, mineralization in Benjamin River IOA prospect are divided into four stages: (1) oxidized magmatic stage that crystallized apatite, augite and anhydrite; (2) sodic metasomatic stage accompanying alteration of magmatic minerals; (3) oxidized fluid stage (magnetite–epidote group minerals mineralization); and (4) reduced fluid stage (pyrite mineralization).     

Large ageostrophic currents in the abyssal layer southeast of Kyushu, Japan, by direct measurement of LADCP

With full-depth LADCP velocity data collected in a wide area southeast of Kyushu, Japan, large velocity currents, occasionally exceeding 15 cm s^?1, were observed in a thick, 500–1,500 m, near-homogeneous density layer below approximately 3,000 m depth around the steep topographies. The currents were found not to flow along the topographic contours, and to be strongly ageostrophic. The directions of the bottom-layer currents are rather related with phase of the semi-diurnal tides, suggesting deeply intruded internal tides generated at the steep topographies.     

Practical evaluation of carbon sources of forest soils in Slovenia from stable and radio-carbon isotope measurements

Carbon sources were estimated by measuring carbon isotope ratios (??¹³C and ??¹⁴C) with accelerator mass spectrometry (AMS) in forest soils of different lithology. Six locations were selected in temperate deciduous and coniferous stands in Slovenia (?irovski vrh, Idrija, Ko?evski Rog, Pohorje, Gori?nica, and Rakitna), where carbonate rocks consisting of limestone and dolomite are abundant as underlying bedrock. Carbon isotope fractionation would not have occurred in two carbonaceous soils, since the values of both ??¹³C and ??¹⁴C changed consistently in these soils after thermal (550°C, 2?h) or chemical (1?M HCl, 24?h) treatments. Organic components were found to be predominant carbon sources (70?C100%) in the uppermost portions (0?C2?cm in depth). In deeper portions at a depth of about 30?C35?cm, soil carbon may be derived completely from underlying carbonate minerals in Idria, western part of Slovenia. The Combination of heat and chemical treatments with AMS provides practical information on soil carbon sources in carbonaceous soils.