October 23, 2011 Turkey/Van–Ercis earthquake: structural damages in the residential buildings

On October 23, 2011, a magnitude of Mw 7.2 earthquake struck the Van province in eastern Turkey which caused approximately 600 life loss and 4,000 injured people. Although the recorded peak ground accelerations were relatively low (0.15–0.2 g) compared with that of other recent destructive Turkish earthquakes and the code-based design response spectrum, a large number of reinforced concrete buildings with 4–6 stories and non-engineered masonry buildings were either heavily damaged or collapsed in the region. Based on the post-earthquake technical inspections, the goal of this paper is to introduce major reasons for structural damages in the disaster area and to discuss these failures along with the approaches given in the design code which is renewed after August 17, 1999 Marmara Earthquake. Some remarkable lessons learned from earthquake-induced failures and damages specific to building construction techniques are presented in this paper.     

Analysis of the strong motion data of the 1995 Dinar, Turkey earthquake

Dinar earthquake (M_w=6.0, USGS) occurred on October 1, 1995 causing casualties and physical damage (I_o=VII–VIII MSK). The earthquake was associated with predominantly normal faulting. The PGA in Dinar was 0.33 g. Strong motion data associated with the mainshock and aftershocks of the 1995 Dinar, Turkey earthquake have been analyzed to investigate the source, attenuation and site response parameters. Strong motion data were baseline corrected, local magnitudes were computed and inelastic attenuation parameters, seismic moments and corner frequencies were assessed. A parametric analysis is attempted to understand the correlation of damage distribution with the fault parameters. It is believed that the obtained data will complement the relatively scarce earthquake data associated with extensional regimes.     

Analysis of the light curves of the eclipsing system V548 Cygni

The eclipsing binary V548 Cygni was observed photoelectrically in yellow and blue light at Ege University Observatory in 1975. A total of 857 observations were obtained of each colour. Three times of minima were obtained and new light elements were derived. The orbital analysis were made by the methods of Kitamura and Wood. The system has a third body whose total luminosity is greater than that of secondary companion.     

Permeability and compression characteristics of municipal solid waste samples

Four series of laboratory tests were conducted to evaluate the permeability and compression characteristics of municipal solid waste (MSW) samples. While the two series of tests were conducted using a conventional small-scale consolidometer, the two others were conducted in a large-scale consolidometer specially constructed for this study. In each consolidometer, the MSW samples were tested at two different moisture contents, i.e., original moisture content and field capacity. A scale effect between the two consolidometers with different sizes was investigated. The tests were carried out on samples reconsolidated to pressures of 123, 246, and 369 kPa. Time settlement data gathered from each load increment were employed to plot strain versus log-time graphs. The data acquired from the compression tests were used to back calculate primary and secondary compression indices. The consolidometers were later adapted for permeability experiments. The values of indices and the coefficient of compressibility for the MSW samples tested were within a relatively narrow range despite the size of the consolidometer and the different moisture contents of the specimens tested. The values of the coefficient of permeability were within a band of two orders of magnitude (10⁻⁶–10⁻⁴ m/s). The data presented in this paper agreed very well with the data reported by previous researchers. It was concluded that the scale effect in the compression behavior was significant. However, there was usually no linear relationship between the results obtained in the tests.     

Evaluation of digital image processing (DIP) in analysis of magnetic separation fractions from Na-feldspar ore

Combination of flotation and magnetic separation methods is widely used for enrichment of feldspar ores by purifying from dark-colored gangue minerals such as iron and titanium. In this study, the removal of dark-colored minerals from feldspar ore (Aydin Cine region of Turkey) was studied using a dry magnetic separator. The effect of several parameters such as feed particle size, blade angle, and roll speed on the removal efficiency was investigated in detail. In addition, the gangue contents of the magnetic and non-magnetic products were determined by a digital image processing (DIP) method in terms of using color differences between the feldspar sample and gangue minerals. The results obtained from this study clearly indicated that the dry magnetic separation method can be successfully applied in enrichment of feldspar. Meanwhile, the particle size of the sample showed no significant influence on the separation recovery. According to the results obtained from the digital image processing process, the sample with 0.04% cross sectional area of dark-colored minerals can be obtained at roll speed of 100 rpm and 130° of blade angle using the original particle size of 500×106 μm. Additionally, most importantly, these results showed that digital image processing method can be used to determine gangue content (dark-colored minerals) of the magnetic separation products compared to conventional methods as a simple, a reliable, and a repeatable method.