Analytical method of radiation by a wave energy device with dual rectangular floating bodies

The system with one floating rectangular body on the free surface and one submerged rectangular body has been applied to a wave energy conversion device in water of finite depth. The radiation problem by this device on a plane incident wave is solved by the use of an eigenfunction expansion method, and a new analytical expression for the radiation velocity potential is obtained. The wave excitation force is calculated via the known incident wave potential and the radiation potential with a theorem of Haskind employed. To verify the correctness of this method, an example is computed respectively through the bound element method and analytical method. Results show that two numerical methods. are in good agreement, which shows that the present method is applicable. In addition, the trends of hydrodynamic coefficients and wave force are analyzed under different conditions by use of the present analytical method.     

The impact of deformation on vortex development in a baroclinic moist atmosphere

A mathematical relation between deformation and vertical vorticity tendency is built by introducing the frontogenesis function and the complete vertical vorticity equation, which is derived by virtue of moist potential vorticity. From the mathematical relation, it is shown that properly configured atmospheric conditions can make deformation exert a positive contribution to vortex development at rates comparable to other favorable factors. The effect of deformation on vortex development is not only related to the deformation itself, but also depends on the current thermodynamic and dynamic structures of the atmosphere, such as the convective stability, moist baroclinicity and vertical wind shear(or horizontal vorticity). A diagnostic study of a heavy-rainfall case that occurred during 20–22 July 2012 shows that deformation has the most remarkable effect on the increase in vertical vorticity during the rapid development stage of the low vortex during its whole life cycle. This feature is mainly due to the existence of an approximate neutral layer(about 700 h Pa) in the atmosphere where the convective stability tends to be zero. The neutral layer makes the effect of deformation on the vertical vorticity increase significantly during the vortex development stage, and thus drives the vertical vorticity to increase.     

1971—2010年京津冀大城市热岛效应多时间尺度分析

利用1971—2010年均一化的京津冀区域逐日气温数据与质量控制后的2011年自动站逐时气温数据,分析了北京、天津和石家庄热岛效应的多尺度时间变化特征。结果表明,三个城市平均、最高和最低气温的热岛效应呈非对称性特征,最强为最低气温的热岛效应,其次为平均气温的热岛效应,最弱为最高气温的热岛效应。北京平均气温的热岛效应最强,其次为天津,石家庄相对较弱,石家庄平均气温的热岛效应近40年呈显著上升趋势,每10年达0.13℃。石家庄最高气温的热岛效应最强,其次为北京,最小为天津,近40年北京最高气温的热岛效应呈缓慢上升趋势,每10年增加0.06℃,石家庄变化不明显,天津呈微弱下降趋势。最低气温的热岛在北京最强,其次为天津,最小为石家庄,近40年最低气温热岛效应天津呈明显上升趋势,每10年增加0.18℃,其次为石家庄,北京呈微弱下降趋势。三个城市的平均气温、最低气温的热岛效应季节变化通常表现为夏季较弱,冬季最强。三个城市最高气温的热岛效应季节变化差异较大,北京10月热岛效应最弱,其他月份变化不大;天津热岛效应6月最弱,在1或12月最强;石家庄4和5月热岛效应最强,10月热岛效应最弱。由2011年自动站数据得到的平均气温热岛效应与1971—2010年的40年平均得到的平均气温的热岛效应季节变化具有类似的规律。2011年自动站热岛效应在一天中表现为白天热岛强度较低,而夜间热岛强度较高。     

东中国海黑潮海洋锋的季节变化特征及其成因

利用高分辨率海洋和大气再分析资料研究了东中国海黑潮海洋锋的季节变化特征及其成因。研究表明,东海黑潮海洋锋存在明显的季节变化,从冬季到次年春季逐渐增强,并在春季达到最强,初夏以后强度逐渐减弱,9—10月达到全年最弱。通过诊断混合层热流量方程发现,东海黑潮区一年四季均表现为暖的温度平流,有利于海洋锋的形成和维持,该暖平流也存在季节变化并在春季达到最大,对海洋锋在春季达到最强起了重要作用。海气界面净热通量在秋冬季对海洋锋的形成有促进作用,有利于海洋锋增强,而在春夏季则起抑制作用,促进海洋锋消亡。温度垂直输送全年对海洋锋起一定程度的抑制作用。总之,在海温水平平流和海表净热通量的共同作用下导致海洋锋春季达到最强,而夏秋季海表净热通量和温度垂直输送作用的共同作用致使海洋锋减弱并最后消失。因此,海洋的动力和热力共同作用导致了东海黑潮海洋锋的季节变化,其中海温水平平流和海表净热通量对海洋锋的季节变化起主要作用,而温度垂直输送项对海洋锋的发展起抑制作用,但影响相对较小。     

天津蓟县东水厂锰方硼石矿床成因新认识

天津蓟县东水厂锰方硼石矿床是世界上唯一一个具有经济开发价值的锰方硼石矿床,锰方硼石赋存与中元古代高于庄组二段泥晶白云岩中。本文通过微量元素分析探讨了锰方硼石的成矿环境,测定结果显示Sr/Ba=0.125~0.128;V/(Ni+V)=0.230~0.320;Th/U=4.356~4.898;V/Cr=0.018~0.026,各微量元素对比值范围变化不大;LREE总量为66.12×10~(-6)~67.90×10~(-6),HREE总量(包含Y)为18.88×10~(-6)~19.56×10~(-6),LREE/HREE值为3.38~3.60,Y/Ho值介于28.25~29.14之间,δCe介于0.829~0.854之间,显示为弱的负Ce异常,δEu值介于0.831~0.846之间,显示为弱的负Eu异常。地球化学数据指示其成矿环境属海相沉积环境,海水环境为相对氧化的状态,成矿过程中有陆源物质的加入。Sm/Nd-Eu/Sm图解表明研究区与柴达木盆地第三系蒸发岩较为相似,反应锰方硼石成矿时具有类似的蒸发成因。通过对硼同位素(δ~(11)B的数值范围为1.4‰~10.7‰)的解译进一步探讨了锰方硼石在原生成矿阶段的具体成因(海相蒸发沉积)。结合前人所做的锰方硼石地球化学数据,对东水厂锰方硼石矿床的成因做出了新的解释,即锰方硼石成矿时应属海相蒸发成因,而热液活动的过程则可能是发生于锰方硼石成矿之后,属后期热液改造作用,从而形成了锰方硼石复杂的地球化学特征。     

奇异值分解法在病态问题中的应用

用截断奇异值分解法和修正奇异值分解法对大地测量病态问题进行了处理,并与最小二乘的结果进行了比较,最后将两者方法进行结合同样对病态方程进行了处理,得到了结合奇异值分解的解,并与截断奇异值、修正奇异值分解的解以及真值进行比较,发现结合奇异值分解的解即修正奇异值截断法比截断奇异值和修正奇异值的解更加靠近于真值,修正奇异值截断法相比于截断奇异值和修正奇异值法对于病态方程抗干扰能力更强,更具有实际意义。     

一种多系统组合导航快速选星方法

采用多卫星导航系统组合导航,定位精度和系统可靠性会大幅提升,但导航定位运算量也会成倍增长。为解决多系统组合导航定位精度与实时性之间的矛盾,提出一种新的选星方法。新方法不追求最小GDOP值,而是以满足导航定位精度的GDOP值为前提,结合模糊理论中隶属函数的思想,按卫星在星座中均匀分布为原则进行选星。推导伪距测量的误差模型,分析了GDOP与测量误差之间的关系。北斗、GPS和GLONASS三系统组合导航选星实验结果表明,在不超过3次求解GDOP值的情况下,新方法能以不小于98%的概率得到GDOP≤4。     

A hybrid approach to modeling territorial control in violent armed conflicts

Territorial control is central to the understanding of violent armed conflicts, yet reliable and valid measures of this concept do not exist. We argue that geospatial analysis provides an important perspective to measure the concept. In particular, measuring territorial control can be seen as an application of calculating service areas around points of control. The modeling challenge is acute for areas with limited road infrastructure, where no complete network is available to perform the analysis, and movements largely occur off road. We present a new geospatial approach that applies network analysis on a hybrid transportation network with both actual road data and hexagon‐fishnet‐based artificial road data representing on‐road and off‐road movements, respectively. Movement speed or restriction can be readily adjusted using various input data. Simulating off‐road movement with hexagon‐fishnet‐based artificial road data has a number of advantages including scalability to small or large study areas and flexibility to allow all‐directional travel. We apply this method to measuring territorial control of armed groups in Sub‐Saharan Africa where inferior transport infrastructure is the norm. Based on the Uppsala Conflict Data Program's (UCDP) Georeferenced Event Data (GED) as well as spatial data on terrain, population locations, and limited transportation networks, we enhance the delineation of the specific areas directly controlled by each warring party during civil wars within a given travel time.     

Active Characteristics and Paleoearthquakes in the West Kalpin Nappe Since the Holocene,SW Tianshan Mountain

the Kalpin nappe is an important multiple thrust system. It is important to study the Cenozoic tectonic of the Tianshan Mountain. Holocene active characteristics and paleoearthquake of the Kalpin nappe can be used to evaluate the neotectonic of this area. In this paper, we accurately measured the fault scarp in the front of three thrust-fold faults and analyzed paleoearthquake events in the trenches of the Kalpin nappe. Using the ¹⁰Be exposure age, we obtained those geomorphic surface ages and paleoearthquake times. The result showed that the slip rates of the west Kalpintag fault, aozitag fault and the tuoketag fault were 1.45(+1.68/-0.44) mm/a, 0.81(+0.35/-0.19) mm/a and (0.3±0.05) mm/a, respectively since the Holocene. The slip rate indicated that the increased activity transferred from back-row fault to front-row fault and accorded with the piggy-back propagation model in the Tianshan Mountain. Displacements and recurrence intervals of paleoearthquakes was similar to the slip rate characteristics. It also showed paleoearthquakes in the front row fault were stronger than paleoearthquakes of the back row fault. The strong paleoearthquake which caused the highest surface rupture happened in the Kalpintag fault. The interval of paleoearthquakes was about 4 ka and the displacement of every paleoearthquake was about 3 m in the west Kalpintag fault; the interval of paleoearthquakes was about 2 ka and the displacement of every paleoearthquake was about 1m in the aozitag fault; the tuoketag fault ruptured only one paleoearthquake since 7 ka. The Piqiang tear fault was the tectonic result of different shortening rate between the west Kalpin system and the east Kalpin system. The shortening rate of west Kalpin system was obviously stronger than the east Kalpin system. The huge separation distance was near 20 km between the east and the west back-row fault. Because the slip rate of system transferred to the front-row fault in the piggy-back propagation model, the separation distance (~4 km) between the east and the west front-row fault was increasing.     

湖南大义山岩体白沙子岭矿区钨锡矿深部找矿探索

大义山花岗岩体受"大义山式"北西向张扭性断裂构造控制,具多次侵位的特点,与岩体有关的矿产主要为锡多金属矿。本次补勘的白沙子岭锡矿区有云英岩脉型、蚀变岩体型、矽卡岩型等3类锡多金属矿类型。白沙子岭矿段平行排列的矿脉群在平面上整体呈一椭圆形展布,脉群从中间向两侧单脉的长度、厚度、品位逐渐变小,单个脉体从中间向两端厚度、品位逐渐变低。矿脉两端顶底板断层面上见到产状完全相反的擦痕,推断深部存在着一个椭圆形隐伏母岩体,成矿母岩的上部会形成蚀变岩体型矿体。为此本次补勘工作施工了一坑内深钻,上部见到了蚀变岩体型富锡矿体,下部见钨矿,预测深部找矿有较大的找矿前景。