射电天文台址电子设备电磁辐射评估

射电望远镜具有极高的系统灵敏度,且系统内、系统间及台址内电子设备众多,电磁环境复杂,科学合理地评估台址内电子设备辐射发射对射电天文观测的影响,对系统电磁兼容性设计、无线电管理、屏蔽改造等有重要的指导意义。浅析了射电望远镜系统灵敏度及射电天文领域仪器设备辐射发射相关评估标准;基于射电望远镜系统灵敏度及观测需求,计算了南山25 m射电望远镜馈源口面干扰电平限值,并给出了天线旁瓣增益的计算方法;提出一种基于干扰电平限值、旁瓣增益、干扰测量、路径衰减的电子设备电磁辐射评估方法,并针对南山25 m射电望远镜天线驱动电磁辐射进行了评估,给出了屏蔽需求。     

基于Matlab/Simulink的天线系统自适应滤波器的仿真实现

为了使天线系统接收和显示的信号更清晰,达到消除系统噪声和电磁干扰的目的,针对中国科学院新疆天文台南山观测基地对射电天文观测和深空探测(探月工程和火星探测)的特殊要求,利用Matlab/Simulink强大的数值计算与仿真功能实现了一种依据自适应方法滤除噪声的滤波器。首先选择脉冲星1910+0728和1913-0440的观测信号为滤波参考信号。在Matlab上通过编写M文件设计了滤波算法并有效滤除了噪声。然后运用Simulink进行建模仿真,通过不断改变系统阶数与步长找到了滤波效果最好的自适应滤波器,确定了其最优参数为8阶,迭代步长为0.005。实验表明在这种阶数和步长下,滤波器能在保证快速滤波的前提下有效地还原接收信号的轮廓,将偏差降到最小。仿真最终结果表明自适应滤波器滤波效果良好,实用性强,满足了射电天文观测和探月的需求。     

基于小波变换的射频干扰消除方法的研究

在射电天文观测中,射频干扰(Radio Frequency Interference, RFI)会以多种形式混入望远镜接收系统,给观测带来误判或者降低观测信噪比.近年来国内国际射电天文快速发展,国内国际大型射电望远镜和阵列先后建设,观测灵敏度大为提高,射频干扰的影响尤为突出.随着科技发展和人类活动的加剧,射频干扰日益严重且不可逆转.提出利用2维离散小波变换的方法分析射电天文观测的数据,对望远镜系统输出的时间频率序列进行小波变换,根据小波系数分离出原始信号中各分量,每个分量统计得到相应的阈值,将各分量与阈值相比较识别干扰成分并标记去除.利用该方法对实际观测数据进行了处理,结果表明该方法能够很好地标记并消减干扰信号,且提高了观测的信噪比.     

快速射电暴观测数据干扰缓解方法研究

从海量的天文观测数据中快速搜寻罕见的快速射电暴(Fast Radio Burst, FRB)事件, 干扰缓解是其中一项关键而具有挑战的工作. 射频干扰(Radio Frequency Interference, RFI)会淹没真实的天文事件, 还会导致搜寻管线输出大量的假阳性候选体. 由于干扰来源及其种类的复杂性, 目前并没有一种通用的方法可以解决这个问题. 为了降低干扰对FRB观测搜寻的影响, 分析和研究了南山26m射电望远镜L波段观测数据中的干扰情况, 针对主要的窄带干扰和宽带干扰建立了3层次的干扰缓解处理流程, 从而有效缓解了观测数据的干扰污染情况. 将该流程嵌入到FRB色散动态谱搜寻(Dispersed Dynamic Spectra Search, DDSS)管线中, 实验结果表明, 搜寻管线的检测率和检测精度得到了进一步的提高. 该方法为FRB观测数据干扰缓解处理提供了有价值的参考.     

大规模脉冲星候选体信号的无监督聚类分析研究

随着500 m口径球面射电望远镜(Five-hundred-meter Aperture Spherical radio Telescope, FAST)等大型射电望远镜的建设和使用,脉冲星巡天数据进入PB时代.为解决如此大量高速采样的标量数据挖掘问题,促进新天文现象的发现,提出一种基于无监督聚类的脉冲星候选体筛选方案.该方案采用基于密度层次、划分方法的混合聚类算法,结合MapReduce/Spark并行计算模型和基于滑动窗口的分组策略,进而提高大量候选体信号筛选的效率.通过在脉冲星数据集HTRU2 (High Time Resolution Universe)上的对比实验,结果表明该算法能取得较高的精确度和召回率,分别是0.946和0.905,并且当并行节点足够时,该算法的时间复杂度相比串行执行明显下降.可见,该方法为脉冲星观测大数据的分析挖掘提供一种可行思路.     

射电天文自适应抗干扰算法研究

全球性卫星导航系统占用了L波段在1.1 GHz~1.6 GHz之间约150 M带宽,严重限制了射电天文在该频段的观测。将通信、雷达等领域的自适应滤波方法应用于消除"北斗二号"卫星信号给中性氢(HI)21 cm谱线观测带来的射频干扰(Radio Frequency Interference,RFI)。为了提高最小均方误差(Least Mean Square,LMS)自适应算法的性能,在对一类传统变步长最小均方误差算法研究的基础上,提出了步长与误差信号之间的一种新的函数关系,进一步改善了自适应滤波算法的性能。在相同收敛速度或者相同稳态误差的前提下,改进后的算法具有更小的稳态误差或者更快的收敛速度。计算机仿真实验结果与理论分析一致,验证了改进后的变步长自适应滤波算法在射电天文射频干扰消除中的性能优于传统算法。     

基于独立成分分析的射频干扰信号消除方法

射电天文已成为人类研究宇宙的重要途径。但随着人类生产、生活的发展,射频干扰信号对射电天文观测的影响越来越严重,观测数据的好坏关系到科学成果的质量甚至结论的真伪。目前广泛采用基于阈值判断射频干扰,对干扰信号直接舍弃部分观测数据的方法。此类方法存在阈值确定困难、观测带宽和时间被缩减等问题。针对脉冲星观测射电信号中,各干扰信号及射电信号统计独立以及呈现出的非高斯性,利用独立成分分析对混合信号进行分解,并根据观测信号中脉冲星信号和干扰信号的分布特点识别脉冲星信号,实现干扰信号消除。使用该方法对云南天文台40 m射电望远镜接收到的脉冲星观测信号进行独立成分分析,分解出独立的射频干扰信号和脉冲星信号,消除射频干扰信号。独立成分分析法在干扰信号消除、射电信号保留及信噪比方面均取得良好效果。     

L-band RFI Measurement and Mitigation at the NSRT Site

近些年，南山台址内部各类电子设备不断引入，此过程忽视了有效的设备管理及电磁防护，且台址周边无线电业务增多，以致电波环境恶化。为改善台址电波环境，采用一种准实时电波环境测量方法测量分析了台址周边瞬态信号的影响；另外，为提高微弱信号检测能力，采用便携式电磁干扰测量系统和26m射电望远镜对台址主要干扰信号特征及来源进行测量分析。依据测量和分析结果，采用屏蔽及滤波技术对望远镜观测室内部主要干扰源进行电磁防护，并针对屏蔽工程的有效性进行测量评估，结果表明，采用的电磁屏蔽措施有效。另外，提出了初步南山无线电宁静区保护办法缓解台址外部电磁干扰。     

德令哈13.7m望远镜接收机抗射频干扰研究

在天文观测中,射频干扰会造成假谱,降低数据的可靠性和有效性.射频干扰消减旨在减少干扰信号对射电天文观测的影响,包含器件方面的技术革新和数据处理领域的方法研究.针对德令哈13.7 m望远镜接收机中频部分引入的射频干扰,通过优化中频器件的抗射频干扰能力,提高了接收机的整体抗射频干扰能力,以主动消除方法来减少射频干扰耦合到接收机内部.分析了接收机干扰的传输路径,提出了器件射频干扰的直接耦合系数和器件射频干扰的系统耦合系数的概念,为定位干扰敏感器件并量化干扰引入比重提供了基础.经过抗射频干扰优化后,接收机抗干扰能力改善30 dB左右,望远镜的天文观测效率提高10%以上.     

大口径射电望远镜电磁兼容评估技术研究

电磁兼容性是设备或系统的重要性能指标, 也是保障系统的工作效能和提高系统可靠性的重要因素. 大口径射电望远镜运行阶段, 台址周围无线电业务及内部潜在的电磁干扰会降低观测系统灵敏度、影响天文观测的质量. 本论文针对拟建的新疆110 m全向可动射电望远镜(Qi Tai raido Telescope, QTT)开展了系统电磁兼容评估技术及控制方法研究, 具有重要的工程应用价值. 首先, 依据现有电波环境测量方法的不足, 深入分析了仪器设备的关键参数配置方法及测量时间计算方法, 采用Y因子法校准测量数据, 提出一种准实时电波环境测量方法. 面向高重复性宽带频谱, 分析了宽带频谱信号和噪声特征, 结合标准差理论, 提出一种基于邻值比较的信噪分离方法, 并采用邻值统计方法优化关键参数, 提高信噪分离精度. 针对QTT台址, 开发了自动化电波环境监测系统, 该系统6 GHz以下频段系统增益大于40 dB, 系统噪声系数小于2 dB, 测量不确定度小于1.49 dB, 具有极高的系统灵敏度和测量精度; 分析了频谱监测数据流, 设计了基于HDF5 (Hierarchical Data Format version 5)的数据存储格式, 开发了自动化电波环境测量和监控软件及数据处理软件. 依据QTT台址长期监测数据, 评估分析了台址电磁环境、主要干扰源特征及其影响. 其次, 提出大口径射电望远镜馈源口面干扰电平限值量化方法, 建立了基于台址地形的电波传播模型, 分析了现有电波传播模型的优缺点及适应性, 结合QTT台址实际地形及地质特征, 采用Longley-Rice和Two-Ray电波传播模型, 预测分析了QTT台址潜在干扰区域电磁干扰达到射电望远镜的电波路径衰减, 结合大口径射电望远镜天线增益量化方法, 提出设备所在位置干扰电平限值量化方法, 运用该方法对QTT台址潜在干扰区域的干扰电平限值进行量化. 依据设备所在位置干扰电平限值, 调研分析了国内外军用、民用电磁兼容测量标准, 结合电磁干扰对射电天文观测的影响, 提出一种大口径射电望远镜电磁兼容控制方法, 解决了现有电波暗室测量系统无法直接测量评估电子设备电磁兼容的问题, 该电磁兼容控制方法计划应用于QTT建设及运行阶段, 确保系统拥有良好的电磁兼容性. 最后, 依据QTT台址潜在干扰区域干扰电平限值, 结合典型电子设备电磁辐射频谱, 分析了QTT电磁兼容设计需求, 提出电磁兼容设计初步方案. 另外, 针对台址建筑设施内的中低电磁辐射干扰源, 提出一种低成本建筑屏蔽方法, 应用于QTT台址现有建筑.     

射电望远镜远场区域强干扰源规避方法研究

随着频率使用率的提高, 射电天文台址地面或空间存在强电磁干扰致使望远镜接收机系统处于非线性状态. 为减少强电磁干扰的影响、提高天文观测效率, 提出了一种基于望远镜远场区域的强干扰源规避方法. 首先, 通过仿真分析确定的射电望远镜远场方向图, 结合望远镜与干扰源之间的位置关系, 分析了强电磁干扰到达射电望远镜焦点处的功率响应, 并依据接收机第2阶中频放大器性能参数, 确定射电望远镜处于非饱和状态的规避角度计算方法. 其次, 采用该方法计算分析了民航飞机对射电望远镜的影响, 若民航飞机上有主动发射的干扰源, 且不经过反射等传播现象, 当射电望远镜主波束轴偏开一定方向后, 可有效降低对射电望远镜的干扰强度.     

相控阵馈源MVDR波束合成器缓解RFI仿真

相控阵馈源(Phased array feeds, PAFs)接收机作为下一代微波接收机, 为大口径射电天文望远镜的射电干扰(Radio Frequency Interference, RFI)缓解工作带来了新的解决方法. PAFs接收机对射电望远镜焦平面的电磁波进行空域采样, 返回时域阵列信号, 使用最小方差无失真响应(Minimum Variance Distortionless Response, MVDR)波束合成器可以自适应地识别RFI的方向, 同时抑制RFI在输出信号中的功率, 从而达到提升射电望远镜灵敏度的效果. 仿真结果表明MVDR波束合成器对有源高能量的射电干扰有很强的识别能力和一定程度的缓解能力, 同时, 该波束合成器对各阵元信道中加性噪声累积引起的无源干扰有很强的抑制能力, 因此, PAFs接收机的MVDR波束合成器可以增强日益复杂电磁波环境下射电望远镜的抗干扰能力.     

Radio frequency interference mitigation using pseudoinverse learning autoencoders

Radio frequency interference(RFI) is an important challenge in radio astronomy. RFI comes from various sources and increasingly impacts astronomical observation as telescopes become more sensitive. In this study, we propose a fast and effective method for removing RFI in pulsar data. We use pseudo-inverse learning to train a single hidden layer auto-encoder(AE). We demonstrate that the AE can quickly learn the RFI signatures and then remove them from fast-sampled spectra, leaving real pulsar signals. This method has the advantage over traditional threshold-based filter method in that it does not completely remove contaminated channels, which could also contain useful astronomical information.     

Research on Receiver Anti-RFI of Delingha 13.7 m Telescope

In astronomical observations, the radio frequency interference (RFI) will cause pseudo spectra and reduce the reliability and validity of observational data. The RFI mitigation, which includes many technical innovations of devices and the method studies of data processing, aims at reducing the influence of RFI on the radio astronomical observation. Various efforts were made to improve the anti-RFI capability of the multi-beam receiver (Superconducting Spectroscopic Array Receiver, SSAR) of the Delingha 13.7 m telescope. The interference transmission path was analyzed. The concepts of the device RFI direct coupling coefficient and the device RFI system coupling coefficient were proposed. The proportions of interference introduced in the receiver system by the different devices were quantified, and the interference-susceptible devices in the system were located. After the anti-RFI treatment of the interference-susceptible devices, the anti-RFI capability of the receiver system is improved by 30 dB in average, and the astronomical observation efficiency of the telescope is increased by more than 10%.     

An agile very low frequency radio spectrum explorer

The very low frequency(VLF) regime below 30 MHz in the electromagnetic spectrum has presently been drawing global attention in radio astronomical research due to its potentially significant science outcomes exploring many unknown extragalactic sources,transients,and so on.However,the nontransparency of the Earth's ionosphere,ionospheric distortion and artificial radio frequency interference(RFI) have made it difficult to detect the VLF celestial radio emission with ground-based instruments.A straightforward solution to overcome these problems is a space-based VLF radio telescope,just like the VLF radio instruments onboard the Chang'E-4 spacecraft.But building such a space telescope would be inevitably costly and technically challenging.The alternative approach would be then a ground-based VLF radio telescope.Particularly,in the period of post 2020 when the solar and terrestrial ionospheric activities are expected to be in a 'calm' state,it will provide us a good chance to perform VLF ground-based radio observations.Anticipating such an opportunity,we built an agile VLF radio spectrum explorer co-located with the currently operational Mingantu Spectra Radio Heliograph(MUSER).The instrument includes four antennas operating in the VLF frequency range 1-70 MHz.Along with them,we employ an eight-channel analog and digital receivers to amplify,digitize and process the radio signals received by the antennas.We present in the paper this VLF radio spectrum explorer and the instrument will be useful for celestial studies of VLF radio emissions.     

Radio frequency self-interference from a data processing centre at a radio telescope site

Apart from externally generated Radio Frequency Interference (RFI), the occurrence of self-interference is a major concern at any modern radio telescope site. Antenna servo motor controllers, data acquisition processors, and fast computing capabilities operate very close to extremely sensitive and wideband radio astronomical receivers. In this paper, we present a set of measurements of the RFI level generated by a cluster of computers that will be installed at the site of the Sardinia Radio Telescope (SRT). The measured levels are compared to Recommendation ITU-R RA.769-2, which gives the threshold levels for interference detrimental to radio astronomy observations. Our analysis shows that, with proper shielding of the noisiest devices, it will be possible to preserve the present excellent RFI conditions of the SRT site.     

RFI detection by automated feature extraction and statistical analysis

In this paper we present an interference detection toolbox consisting of a high dynamic range Digital Fast‐Fourier‐Transform spectrometer (DFFT, based on FPGA‐technology) and data analysis software for automated radio frequency interference (RFI) detection. The DFFT spectrometer allows high speed data storage of spectra on time scales of less than a second. The high dynamic range of the device assures constant calibration even during extremely powerful RFI events. The software uses an algorithm which performs a two‐dimensional baseline fit in the time‐frequency domain, searching automatically for RFI signals superposed on the spectral data. We demonstrate, that the software operates successfully on computer‐generated RFI data as well as on real DFFT data recorded at the Effelsberg 100‐m telescope. At 21‐cm wavelength RFI signals can be identified down to the 4σ _rms level. A statistical analysis of all RFI events detected in our observational data revealed that: (1) mean signal strength is comparable to the astronomical line emission of the Milky Way, (2) interferences are polarised, (3) electronic devices in the neighbourhood of the telescope contribute significantly to the RFI radiation. We also show that the radiometer equation is no longer fulfilled in presence of RFI signals. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)