内蒙古银额盆地居延海坳陷X井地层划分修正及其油气地质意义

对银额盆地居延海坳陷X井主要烃源岩发育层段和油气显示层段巴音戈壁组的生物组合、岩石学特征、碎屑岩颜色,以及镜煤反射率随深度变化等进行综合分析,提出了原地层划分存在的问题。通过与路井凹陷和路北凸起带的地层对比,以及过X井的地震反射特征分析,对主要岩石地层单元划分进行了修正。修正后的X井钻遇的主要烃源岩层段和含油显示层为二叠系,与路井凹陷及路北凸起的钻井资料一致,因此应将二叠系作为居延海坳陷油气勘探的主要目的层。     

银额盆地及其邻区石炭系—二叠系油气资源远景调查主要进展及成果

针对影响石炭系—二叠系油气地质条件与油气资源潜力评价的关键地质问题,开展产、学、研联合攻关,采用盆山结合、地质与地球物理结合的工作手段,在石炭纪—二叠纪盆地形成与演化、沉积体系与沉积相展布、石炭系—二叠系烃源岩评价等方面取得了系列新认识。明确了银额盆地及其邻区石炭纪—二叠纪为典型的裂谷裂陷盆地,晚石炭世—早二叠世为盆地发育的鼎盛时期,以浅海陆棚相沉积为主;发现多套厚度大、横向分布稳定,且有机质丰度中等—高,并以II型干酪根为主的成熟—高成熟烃源岩,不存在区域变质;于上古生界风化壳钻获的天然气和原油地球化学特征指示与石炭系烃源岩具有显著亲缘关系;初步预测研究区石炭系—二叠系油气资源前景,圈定了有利勘探区和较有利勘探区。     

内蒙古西部额济纳旗祥探9井石炭系—二叠系 烃源岩地球化学特征

额济纳旗地区祥探9井揭示的石炭系—二叠系为火山岩+碎屑岩组合,火山岩锆石U-Pb谐和年龄分布在(302.2±7.8)~(319.9±4.5)Ma之间,对应的地层时代相当于晚石炭世,岩性组合特征与大狐狸山剖面干泉组(C2P1g)可以对比,确定为干泉组。该井揭示石炭系—二叠系1027.4m(未穿),其中4m和4m以上的暗色泥岩(或粉砂质泥岩)20层,累计厚度288.5m,占地层厚度的28.1%。少量钻井岩心样品进行的烃源岩地球化学特征分析表明,有机质丰度中等—好,干酪根类型为Ⅰ—Ⅱ1型,有机质演化进入成熟—高成熟阶段,显示了良好的生烃条件。与邻近的大狐狸山剖面干泉组烃源岩样品分析结果对比,祥探9井取得的样品有机质丰度显著高于地表剖面样品,TOC为地表剖面样品的1.8倍,热解产油潜量(S1+S2)为地表剖面样品的295.3倍,氯仿沥青“A”为地表剖面样品的32.8倍,总烃(HC)为地表剖面样品的42倍。干酪根类型评价指标分析,井下岩心样品H/C-O/C能较好地反映干酪根类型,地表剖面样品受风化作用的影响H元素显著降低,H/C-O/C无法进行干酪根类型评价,说明风化作用对烃源岩丰度和类型评价指标的影响较大。     

内蒙古西部额济纳旗祥探9井石炭系—二叠系烃源岩地球化学特征

额济纳旗地区祥探9井揭示的石炭系—二叠系为火山岩＋碎屑岩组合,火山岩锆石U-Pb谐和年龄分布在（302.2±7.8）-（319.9±4.5）Ma之间,对应的地层时代相当于晚石炭世,岩性组合特征与大狐狸山剖面干泉组（C2P1g）可以对比,确定为干泉组。该井揭示石炭系—二叠系1027.4m（未穿）,其中4m和4m以上的暗色泥岩（或粉砂质泥岩）20层,累计厚度288.5m,占地层厚度的28.1%。少量钻井岩心样品进行的烃源岩地球化学特征分析表明,有机质丰度中等—好,干酪根类型为Ⅰ—Ⅱ1型,有机质演化进入成熟—高成熟阶段,显示了良好的生烃条件。与邻近的大狐狸山剖面干泉组烃源岩样品分析结果对比,祥探9井取得的样品有机质丰度显著高于地表剖面样品,TOC为地表剖面样品的1.8倍,热解产油潜量（S1＋S2）为地表剖面样品的295.3倍,氯仿沥青＂A＂为地表剖面样品的32.8倍,总烃（HC）为地表剖面样品的42倍。干酪根类型评价指标分析,井下岩心样品H/C-O/C能较好地反映干酪根类型,地表剖面样品受风化作用的影响H元素显著降低,H/C-O/C无法进行干酪根类型评价,说明风化作用对烃源岩丰度和类型评价指标的影响较大。     

二连盆地石炭系—二叠系烃源岩有机地球化学特征及生烃潜力

二连盆地海相烃源岩主要为海槽沉积的石炭系—二叠系泥岩和碳酸盐岩。根据盆地周缘69个露头剖面样品的残余有机碳含量等地球化学实验数据,分析了石炭系—二叠系海相烃源岩的有机质丰度、类型、热演化程度。针对地表烃源岩样品具有高热演化、低丰度的地球化学特征,在有机质丰度的热解损失和地表风化损失校正基础上,采用TSM盆地模拟技术计算烃源岩生烃强度。综合分析认为,二连盆地石炭系—二叠系海相烃源岩具有低—中等级别的生烃能力。     

内蒙古西部额济纳旗希热哈达地区二叠系页岩油(气)地质条件初探

银额盆地是中国内陆地区油气地质工作程度极低的地区之一,前人以中生界为目的层的油气勘探进展缓慢,通过十余年的油气基础地质调查,发现石炭—二叠系具有较好的油气资源前景。笔者通过银额盆地希热哈达地区地质调查井和煤田钻井岩心采集的大量样品,开展了二叠系暗色泥岩分布、有机质丰度、类型、成熟度、矿物组成、储集特征和页岩油气显示等页岩油(气)地质条件的综合研究,认为希热哈达地区二叠系发育分布广、厚度大、有机质丰度高、Ⅱ_1~Ⅱ_2型优质烃源岩具有良好的生烃潜力;暗色泥岩中脆性矿物的含量较高,黏土矿物以伊利石为主,蒙皂石含量较高,有利于吸附气的聚集和后期压裂改造形成裂缝;暗色泥岩物性较好,裂缝、孔洞、残余原生孔隙、次生溶蚀孔和微裂缝等孔(缝)隙发育,具有良好的储集条件,且在钻井岩心中见到了二叠系良好页岩油气显示,指示了希热哈达地区二叠系具有良好的页岩油(气)资源前景,是银额盆地值得探索的新层系和新领域。     

鄂尔多斯盆地二叠系烃源岩地球化学特征与沉积环境的关系

鄂尔多斯盆地二叠系烃源岩是盆地重要潜在的生烃岩系,以钻井岩心地球化学分析资料为主,对泥岩、泥质碳酸盐岩的微量元素、稀土元素和有机质地球化学特征进行了系统分析,其中微量元素含量与同类岩石的克拉克值相比,差别较大。轻稀土富集程度较高,重稀土相对较低,Ce/Ce*具有较明显的正异常,反映出烃源岩沉积环境总体为还原环境。研究认为,半深湖—深湖相带沉积的灰黑色泥岩类烃源岩还原程度强,有机质丰度高,有机质能被及时埋藏;河流—沼泽相沉积环境沉积的灰色—绿灰色泥岩类烃源岩有机质丰度较低。还原程度强、具一定深度水体的沉积相带是原始有机质沉积的良好场所,有机质能沉积并及时保存下来;而气候条件相对干燥、降水少、陆源碎屑物补充不足或较长时间处于氧化环境条件下沉积的泥质碳酸盐岩类岩石,有机质丰度明显偏差。     

江汉盆地海相地层有效烃源岩的识别

海相地层或海相碳酸盐岩烃源岩地球化学评价的焦点问题之一是如何鉴定有机质丰度下限和划分有效烃源岩与非有效烃源岩。江汉盆地海相地层烃源岩的地球化学研究表明,在有机质成熟演化过程中,烃源岩有机碳(TOC)含量不会有明显的降低,有机碳含量是有机质丰度评价的有效地球化学指标。参考国内外有关碳酸盐岩烃源岩有机质丰度的评价标准,结合本区油气显示,该高演化区有效碳酸盐岩烃源岩有机碳的下限值为0.2%～0.3%,二叠系烃源岩为有效烃源岩。     

江汉盆地海相地层有效烃源岩的识别

海相地层或海相碳酸盐岩烃源岩地球化学评价的焦点问题之一是如何鉴定有机质丰度下限和划分有效烃源岩与非有效烃源岩.江汉盆地海相地层烃源岩的地球化学研究表明,在有机质成熟演化过程中,烃源岩有机碳(TOC)含量不会有明显的降低,有机碳含量是有机质丰度评价的有效地球化学指标.参考国内外有关碳酸盐岩烃源岩有机质丰度的评价标准,结合本区油气显示,该高演化区有效碳酸盐岩烃源岩有机碳的下限值为0.2%～0.3%,二叠系烃源岩为有效烃源岩.     

江汉盆地海相地层有效烃源岩的识别

海相地层或海相碳酸盐岩烃源岩地球化学评价的焦点问题之一是如何鉴定有机质丰度下限和划分有效烃源岩与非有效烃源岩.江汉盆地海相地层烃源岩的地球化学研究表明,在有机质成熟演化过程中,烃源岩有机碳(TOC)含量不会有明显的降低,有机碳含量是有机质丰度评价的有效地球化学指标.参考国内外有关碳酸盐岩烃源岩有机质丰度的评价标准,结合本区油气显示,该高演化区有效碳酸盐岩烃源岩有机碳的下限值为0.2%～0.3%,二叠系烃源岩为有效烃源岩.     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。