黑龙江省三矿沟夕卡岩型铁铜矿床矿物学特征及成矿物理化学条件

黑龙江三矿沟铁铜矿床位于大兴安岭北段多宝山矿集区,矿体产于燕山期侵入岩与奥陶系多宝山组大理岩接触带的夕卡岩内。根据矿物共生组合及交代关系,确定热液成矿过程包括夕卡岩阶段、退夕卡岩阶段和石英硫化物阶段。铁矿化主要发生在退夕卡岩阶段,形成磁铁矿、镜铁矿等铁氧化物,呈浸染状、条带状、块状产于钙铁榴石夕卡岩中。铜矿化主要发生在石英硫化物阶段,形成黄铜矿、斑铜矿等硫化物,交代早期矿物。电子探针分析等研究表明,三矿沟铁铜矿床发育钙质夕卡岩矿物组合,其石榴子石主要为钙铝榴石和钙铁榴石,辉石为透辉石钙铁辉石系列,角闪石属于钙角闪石系列,绿泥石属于I型三八面体富铁绿泥石。石榴子石有3种类型：早期自形粗粒的钙铝榴石(Grt-Ia)和钙铁榴石(Grt-Ib),以及晚期呈脉状产出的钙铁榴石(Grt-Ⅱ)。夕卡岩阶段成矿流体具有高温、弱酸性、高氧逸度的特征;退夕卡岩阶段流体温度降低,pH升高,形成大量铁氧化物;石英硫化物阶段流体温度和氧逸度降低,金属硫化物沉淀。     

云南个旧卡房矿田锡-铜矿床成矿作用过程探讨:成矿流体约束

云南个旧是世界上最大的锡多金属矿区,卡房矿田是其中一个主要的铜矿区。卡房铜矿主要的矿床类型有:变玄武岩型层状铜矿和接触带型铜矿,本文主要对前者进行了流体包裹体测试及同位素地球化学分析,并对比研究了接触带型铜矿的同位素地球化学特征。流体包裹体研究显示,卡房矿田变玄武岩型层状铜矿的成矿流体,属于岩浆流体体系演化的一部分,成矿作用分为三个阶段:石英-磁黄铁矿-黄铜矿阶段(Ⅰ)、石英-方解石-黄铜矿-黄铁矿阶段(Ⅱa)和石英-方解石阶段(Ⅱb)。从Ⅰ-Ⅱa-Ⅱb成矿流体的温度(平均从363.9℃至283.2℃至185.0℃)显著降低,流体盐度(平均从20.18% NaCleqv至12.59% NaCleqv至11.97% NaCleqv)缓慢降低,流体密度(平均从0.854g/cm³至0.863g/cm³至1.001g/cm³)基本不变。显微激光拉曼光谱分析显示流体包裹体的挥发份主要为H₂O及少量CH₄,液相中主要成分为H₂O及少量CO^2-₃。氢、氧同位素研究(δD_H2O值介于-98‰~-79‰;δ¹⁸O_H2O值介于-0.82‰~7.09‰)显示,成矿流体主要以岩浆水为主,在成矿流体上升过程中与地层中的大气降水相混合。硫同位素分析结果表明,卡房矿田变玄武岩型铜矿中硫化物的硫(δ³⁴S值介于-0.86‰~3.8‰)来源于三叠纪变玄武岩,而花岗岩浆和变玄武岩共同为卡房接触带型铜矿(δ³⁴S值介于-3.2‰~6.2‰)提供了成矿所需的大部分硫。     

云南个旧锡矿的玄武岩成矿

个旧锡矿产于个旧东区,是一个以锡铜为主的超大型多金属矿床,具有火山沉积成矿的某些特征。因遭受燕山期花岗岩的叠加改造,区内个旧组卡房段中玄武岩遭受强烈的变质,它又具有花岗岩热液成矿的特征。区内玄武岩的地质地球化学特征表明,印支期玄武岩中的Sn、Cu、Pb、Zn、Ag和Au的质量分数大多数高于世界玄武岩平均值的若干倍;矿石硫化物的硫同位素δ³⁴S为-1.5‰~4.0‰,平均+0.207‰,在幔源硫附近;铅同位素模式年龄分为两组：第一组为180~240 Ma,反映了印支期的火山沉积成矿作用;第二组为80~140 Ma,反映了燕山期花岗岩的叠加改造成矿作用。区内印支期玄武岩为个旧锡铜多金属矿床的形成提供了主要的成矿物质,与成矿有直接联系。     

滇中荒田铅锌矿床Rb-Sr同位素年代学与C-O-S-Pb同位素地球化学特征

滇中荒田铅锌矿床赋存于下二叠统碳酸盐岩与上二叠统峨眉山玄武岩接触界面上,矿体主要呈似层状、透镜状产出。矿石矿物组合以闪锌矿、方铅矿为主,脉石矿物以石英、方解石、白云石为主。热液方解石C、O同位素组成表明荒田铅锌矿床成矿流体中CO_2的碳具有多元性,主要来源于幔源与海相碳酸盐岩的混合碳;硫化物硫同位素组成表明荒田铅锌矿床硫以岩浆硫为主,可能混有其他硫源(可能包括地层硫酸盐),铅同位素表明赋矿围岩、玄武岩和燕山期花岗岩均有可能为成矿提供了成矿物质,是多源混合后的产物;闪锌矿Rb-Sr同位素等时线年龄为(83.2±3.4)Ma,指示荒田铅锌矿床形成于晚燕山期,荒田铅锌矿床成矿动力学背景可能与右江褶皱带在中生代末期发生了大规模的岩石圈伸展有关。而晚二叠世海相喷发火山岩对矿区铅锌矿床的形成起了重要的盖层、赋矿层及矿化作用。综上,荒田铅锌矿床成矿流体中的不同组分来源不同,矿床类型为沉积-改造型矿床。     

新疆博乐喇嘛苏铜矿床地质特征和成因研究

喇嘛苏铜矿床矿区地层铜背景为含量偏低,但矿区岩浆岩含铜较高,“Ｉ”型花岗岩类,成矿阶段划分为３个阶段,石英－氧化物阶段,硫化物阶段,晚期石英－硫化物阶段,硫,铅同位素证据表明,成矿物质主要来源于矿区岩浆岩,氢氧同位素证据表明在氧化物阶段成矿热液主要为岩浆水,硫化物阶段则已是大气降水与岩浆水的混合热液,结合黄铁矿的富硫特征,进一步论证喇嘛苏铜矿床典型夕卡岩型铜矿,并探讨其厚大似层状贫铜矿体内的富铜矿     

滇西北羊拉铜矿床稳定同位素特征及其地质意义

云南羊拉铜矿床位于金沙江构造带中部,是中-晚三叠世金沙江洋盆向西俯冲闭合-碰撞造山过程中形成的一个大型铜矿床.矿体多呈层状、似层状产出,与酸性岩体关系密切,矿体受岩体、围岩和构造“三位一体”共同控制,具明显的夕卡岩型矿床特征.通过对矿区大理岩以及不同成矿阶段形成的典型矿物的稳定同位素地球化学研究,发现夕卡岩中最主要的矿物石榴石的δ18OSMOW为6.7‰,暗示了夕卡岩可能直接继承了酸性岩体的氧同位素组成;主成矿期石英的δD值变化范围为-112‰～-77‰,δ18OH2o值变化范围为-2.42‰～4.85‰,反映了成矿流体可能主要为岩浆水,并有大气降水的加入;方解石的δ13CPDB值变化范围为-5.2‰～-1.7‰,δ18 OSMOW值变化范围为12.7‰～ 20.1‰,表明其碳、氧可能主要来源于岩浆,部分可能来自于大理岩;围岩大理岩的δ13CPDB值为3.6‰～5.0‰,δ18 OSMOW值为21.2‰～ 25.4‰,说明大理岩是由海相碳酸盐岩经重结晶作用形成,随着大理岩与矿体距离的减小,其δ13C、δ18O值都有不断降低的趋势,说明在成矿流体交代大理岩围岩的过程中,低δ13C、δ18O值的流体不断与大理岩发生同位素交换,使大理岩的δ13C、δ18O值降低,且距离矿体越近,同位素交换越强烈;矿石硫化物的δ34S值为-6.9‰～2.5‰,集中于-2‰～1‰,说明矿石硫主要为岩浆硫.综上所述并结合矿床的地质特征,认为羊拉铜矿床为一个典型的夕卡岩型铜矿床.     

个旧老-卡岩体接触-凹陷带锡-铜多金属矿地质特征及成因分析

个旧老—卡岩体接触—凹陷带是个旧矿集区最重要的锡-铜多金属成矿构造带,该带中锡、铜矿产资源十分丰富。通过对凹陷带内矿体地质特征、围岩地层含矿性、微量元素、稀土元素、稳定同位素等的研究,结合大地构造环境,结果认为,凹陷带矿体是多种成矿物质来源,经历多种地质作用、多个大地构造演化阶段的多因复成矿床,接触-凹陷带锡-铜矿体形成主要与燕山中晚期花岗岩岩浆作用有关,其次与印支期海底火山-沉积与海底（火山）喷流-热水沉积成矿作用有关。     

安徽铜陵天马山硫金矿床物质来源探讨

天马山硫金矿床的矿体分为层状 和穿层矿体。接触带矿体是典型的夕卡岩型。层状和穿层矿体受石岩系黄龙组、船山组地层层位和层间断裂控制。铅、硫同位素组成等资料表明,其形成经历了同生沉积和岩浆热液叠加、改造两种性质不同的成矿富集过程。金等金属成矿物质主要来源于岩浆,砷主要来源于地层,硫来源于地层和岩浆。     

个旧锡矿阿西寨矿区矽卡岩型硫化矿特征及找矿标志

云南个旧锡矿阿西寨矿区矽卡岩型硫化矿为地下隐伏的铜、锡矿床,其矿体呈似层状、透镜状沿燕山期隐伏花岗岩体与三叠系中统个旧组(T_2g)之接触带分布。属花岗岩接触带的矽卡岩型硫化矿床;花岗岩体的侵入形成大量的矽卡岩,同时为区内多金属矿床的形成提供了热源及矿物质来源。岩体围岩蚀变矽卡岩化、云英岩化、硫化物化是主要的找矿标志。     

云南个旧老卡岩体钾长石与“玄武岩型”铜矿金云母~(40)Ar-~(39)Ar年龄及其地质意义

个旧变玄武岩系中热液型铜锡多金属矿床主要分布于老厂、卡房矿田西部。文章利用40Ar-39Ar同位素测年方法对老卡隐伏花岗岩体的钾长石、老卡矿田"玄武岩型"铜矿的金云母进行年龄测试。结果显示,老卡岩体钾长石的40Ar-39Ar同位素坪年龄为71.6±0.29 Ma;老厂和卡房"玄武岩型"铜矿蚀变矿物金云母坪年龄分别为81.99±0.85 Ma和82.46±0.85 Ma,表明其形成时代皆为晚白垩世。结合区域资料,指出个旧锡-铜多金属矿田经历了较长的岩浆-热液演化时期,"玄武岩型"铜多金属矿床与燕山晚期花岗岩浆活动相关,为晚白垩世软流圈上涌、岩石圈大规模伸展减薄的产物。     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。