Facies of slurry-flow deposits, Britannia Formation (Lower Cretaceous), North Sea: implications for flow evolution and deposit geometry

ABSTRACT Mud‐rich sandstone beds in the Lower Cretaceous Britannia Formation, UK North Sea, were deposited by sediment flows transitional between debris flows and turbidity currents, termed slurry flows. Much of the mud in these flows was transported as sand‐ and silt‐sized grains that were approximately hydraulically equivalent to suspended quartz and feldspar. In the eastern Britannia Field, individual slurry beds are continuous over long distances, and abundant core makes it possible to document facies changes across the field. Most beds display regular areal grain‐size changes. In this study, fining trends, especially in the size of the largest grains, are used to estimate palaeoflow and palaeoslope directions. In the middle part of the Britannia Formation, stratigraphic zones 40 and 45, slurry flows moved from south‐west and south towards the north‐east and north. Most zone 45 beds lens out before reaching the northern edge of the field, apparently by wedging out against the northern basin slope. Zone 40 and 45 beds show downflow facies transitions from low‐mud‐content, dish‐structured and wispy‐laminated sandstone to high‐mud‐content banded units. In zone 50, at the top of the formation, flows moved from north to south or north‐west to south‐east, and their deposits show transitions from proximal mud‐rich banded and mixed slurried beds to more distal lower‐mud‐content banded and wispy‐laminated units. The contrasting facies trends in zones 40 and 45 and zone 50 may reflect differing grain‐size relationships between quartz and feldspar grains and mud particles in the depositing flows. In zones 40 and 45, quartz grains average 0·30–0·32 mm in diameter, ≈ 0·10 mm coarser than in zone 50. The medium‐grained quartz in zones 40 and 45 flows may have been slightly coarser than the associated mud grains, resulting in the preferential deposition of quartz in proximal areas and downslope enrichment of the flows in mud. In zone 50 flows, mud was probably slightly coarser than the associated fine‐grained quartz, resulting in early mud sedimentation and enrichment of the distal flows in fine‐grained quartz and feldspar. Mud particles in all flows may have had an effective grain size of ≈ 0·25 mm. Both mud content and suspended‐load fallout rate played key roles in the sedimentation of Britannia slurry flows and structuring of the resulting deposits. During deposition of zones 40 and 45, the area of the eastern Britannia Field in block 16/26 may have been a locally enclosed subbasin within which the depositing slurry flows were locally ponded. Slurry beds in the eastern Britannia Field are ‘lumpy’ sheet‐like bodies that show facies changes but little additional complexity. There is no thin‐bedded facies that might represent waning flows analogous to low‐density turbidity currents. The dominance of laminar, cohesion‐dominated shear layers during sedimentation prevented most bed erosion, and the deposystem lacked channel, levee and overbank facies that commonly make up turbidity current‐dominated systems. Britannia slurry flows, although turbulent and capable of size‐fractionating even fine‐grained sediments, left sand bodies with geometries and facies more like those deposited by poorly differentiated laminar debris flows.     

The Rajahmundry Traps, Andhra Pradesh: Evaluation of their petrogenesis relative to the Deccan Traps

Geochemical and geochronological data for rocks from the Rajahmundry Traps, are evaluated for possible correlation with the main Deccan province. Lava flows are found on both banks of the Godavari River and contain an intertrappean sedimentary layer. Based on⁴⁰Ar/³⁹ Ar age data, rocks on the east bank are post K-T boundary, show normal magnetic polarity, and belong to chron 29N. Their chemistry is identical to lavas in the Mahabaleshwar Formation in the Western Ghats, ∼1000km away. It was suggested earlier that the genetic link between these geographically widely separated rocks resulted from lava flowing down freshly incised river canyons at ∼ 64 Ma. For the west bank rocks, recent paleomagnetic work indicates lava flows below and above the intertrappean (sedimentary) layer show reversed and normal magnetic polarity, respectively. The chemical composition of the west bank flow above the intertrappean layer is identical to rocks on the east bank. The west bank lava lying below the sedimentary layer, shows chemistry similar to Ambenali Formation lava flows in the western Deccan.⁴⁰Ar/³⁹ Ar dating and complete chemical characterization of this flow is required to elucidate its petrogenesis with respect to the main Deccan Province.     

History and Goals of Canadian Debris Flow Research,A Review

Debris flows were first recognized in Canada in the 1940s, however, most studies of the topic have been carried out since the early 1980s. An integral part of this paper is the Bibliography of Canadian Subaerial Channelized Debris Flows that contains 295 citations which are also categorized into various subjects and geographical areas. The bibliography is available on the ``World-Wide Web'. Based on a review of past and current research, eleven priority topics for future debris flow research in Canada are outlined.     

Active synsedimentary tectonism on a mixed carbonate–siliciclastic continental margin: third‐order sequence stratigraphy of a ramp to basin transition,lower Sekwi Formation,Selwyn Basin,Northwest Territories,Canada

The lower part of the Early Cambrian Sekwi Formation in the Selwyn Basin of the Northwest Territories, Canada, is composed of two regional, unconformity‐bounded sequences, S0 and S1, which record the first widespread carbonate deposition during the initial Palaeozoic transgression onto the western margin of Laurentia. These Early Cambrian sequences are unique to the western North American Cordillera, representing the only record of primarily deep‐water deposition on a tectonically active, mixed carbonate–siliciclastic ramp during this period. More specifically, the geometry of the Sekwi ramp changed during deposition of S0 and S1, from a shallowly dipping homoclinal ramp during the S0 transgressive systems tract to a steeply dipping tectonically modified ramp during the early highstand systems tract of S0. The steeply dipping ramp profile of S0 was preserved into the early transgressive systems tract of S1. The Sekwi ramp returned to a gently sloping ramp during the late highstand systems tract of S1 and remained so throughout the remainder of Sekwi deposition. The evolving shape of the Sekwi ramp is attributed to syndepositional ‘down to the basin’ faulting during deposition of both S0 and S1 and is recorded by: (i) the westward thickening, irregular geometries of S0 and S1; (ii) geographical restriction of deep‐water facies (including sediment gravity flow deposits); (iii) the presence of large allochthonous blocks; and (iv) the clast composition of sediment gravity flow deposits. Sediment gravity flow deposits play an unusually important role in the sequence stratigraphic interpretation of the lower Sekwi Formation, as they delineate depositional packages, including the maximum flooding zone, the transitions between portions of systems tracts, and the inferred locations of syntectonic extensional faults. Syntectonic faults increased accommodation basinward of an extensive ooid‐shoal complex that developed along the Sekwi ramp crest, greatly influencing sequence geometry and initiating the downslope motion of sediment gravity flows. The syndepositional faulting probably was a continuation of extension that began during the latest Neoproterozoic rifting of western Laurentia. The composition of sediment gravity flow deposits track changing accommodation space on the lower Sekwi ramp and can be used to differentiate systems tracts that probably were related more to tectonism than eustasy.     

The impact of meteoric water on the diagenetic alterations in deep-water, marine siliciclastic turbidites

Meteoric-water flux and formation of kaolinite owing to the dissolution of detrital silicates are common features of continental and paralic sandstones. In deep-water marine sandstones, meteoric-water flux is commonly considered unlikely to occur. However, the study of deep-water, marine sandstones of the Shetland–Faroes Basin on the British continental shelf revealed widespread and extensive dissolution and kaolinitization of mica and feldspar grains, which are attributed to meteoric-water flux during a sea-level lowstand. We suggest that this apparently enigmatic meteoric-water flux mechanism is likely to have occurred by hyperpycnal flow. Hyperpycnal flow occurs when river effluent directly transfers into sediment gravity flow, and enters seawater as a mixture of sediment and fresh water. The likelihood for hyperpycnal flows increases at times when rivers and distributary channels reach the shelf edge, and their flows are delivered directly onto the deepwater slope.     

Ichnology of prodeltaic hyperpycnite–turbidite channel complexes and lobes from the Upper Cretaceous Prairie Canyon Member of the Mancos Shale,Book Cliffs,Utah, USA

The Upper Cretaceous Prairie Canyon Member of the Mancos Shale, Book Cliffs, Utah, contain outstanding examples of prodeltaic turbidity and hyperpycnal flow deposits. Sandstone‐rich, heterolithic and mudstone‐rich channel fills occur near the north‐west entrance to Tusher Canyon, Gunnison Butte and Bootlegger Wash. Mudstone‐rich and heterolithic‐rich hyperpycnal channel deposits are mostly unbioturbated, locally displaying a few specimens of Phycosiphon incertum, Protovirgularia dichotoma, Rosselia socialis, Schaubcylindrichnus coronus and Palaeophycus tubularis. Sandstone‐rich channel deposits consist of wave‐reworked turbidites and hyperpycnites, containing Helminthoidichnites tenuis, Lockeia siliquaria, Phycodes isp., Phycosiphon incertum, Protovirgularia dichotoma, Rosselia socialis, Skolithos linearis and Fugichnia. Scolicia isp. and Chondrites isp. occur locally. Strata along the south‐west entrance of Tusher Canyon record deposition in a prodelta turbidite lobe, but far from its axis. With the exception of a few specimens of Ophiomorpha isp., bioturbation is restricted to the top of the succession, where Curvolithus simplex, Gyrochorte comosa, Lockeia siliquaria, Palaeophycus tubularis and Ptychoplasma excelsum occur. Strata at Hatch Mesa record deposition in a hyperpycnal lobe, near to its axis. Sandstone beds include Curvolithus simplex, Gyrochorte comosa, Ophiomorpha nodosa, Palaeophycus tubularis, Phycosiphon incertum, Protovirgularia dichotoma, Ptychoplasma excelsum, Schaubcylindrichnus freyi, Skolithos linearis, large specimens of Rosselia socialis and indeterminate crustacean burrows. Chondrites isp. is present in the mudstone. High rates of both episodic and sustained sedimentation, degree of substrate consolidation, freshwater discharge and water turbidity are the most important stress factors in both channels and lobes. Taxonomic composition, uneven distribution of bioturbation through the successions, and overall low ichnodiversity help to distinguish these prodeltaic deposits from bathymetrically equivalent offshore strata in the same basin. Hyperpycnal flow deposits are formed in a wide variety of environmental settings, therefore displaying high ichnological variability. Such variability is summarized by characterising ichnofaunas from four different depositional settings: (i) lakes; (ii) shelf deltas; (iii) shelf‐edge deltas; and (iv) deep‐marine systems.     

中国崩塌、滑坡、泥石流灾害危险性评价

地质灾害危险性是地质灾害发育密度、活动规模、活动频次的综合性反映。从这一认识出发,本文论述了地质灾害危险性构成及其评价方法,在此基础上,以县(市、区、旗)和省(直辖市、自治区)为单元,进行了崩塌、滑坡、泥石流灾害危险性评价与区划,分析了危险性分布情况与区域变化规律。      

Slurry-flow deposits in the Britannia Formation (Lower Cretaceous), North Sea: a new perspective on the turbidity current and debris flow problem

The Lower Cretaceous Britannia Formation (North Sea) includes an assemblage of sandstone beds interpreted here to be the deposits of turbidity currents, debris flows and a spectrum of intermediate flow types termed slurry flows. The term ‘slurry flow’ is used here to refer to watery flows transitional between turbidity currents, in which particles are supported primarily by flow turbulence, and debris flows, in which particles are supported by flow strength. Thick, clean, dish‐structured sandstones and associated thin‐bedded sandstones showing Bouma T_b–e divisions were deposited by high‐ and low‐density turbidity currents respectively. Debris flow deposits are marked by deformed, intraformational mudstone and sandstone masses suspended within a sand‐rich mudstone matrix. Most Britannia slurry‐flow deposits contain 10–35% detrital mud matrix and are grain supported. Individual beds vary in thickness from a few centimetres to over 30 m. Seven sedimentary structure division types are recognized in slurry‐flow beds: (M₁) current structured and massive divisions; (M₂) banded units; (M₃) wispy laminated sandstone; (M₄) dish‐structured divisions; (M₅) fine‐grained, microbanded to flat‐laminated units; (M₆) foundered and mixed layers that were originally laminated to microbanded; and (M₇) vertically water‐escape structured divisions. Water‐escape structures are abundant in slurry‐flow deposits, including a variety of vertical to subvertical pipe‐ and sheet‐like fluid‐escape conduits, dish structures and load structures. Structuring of Britannia slurry‐flow beds suggests that most flows began deposition as turbidity currents: fully turbulent flows characterized by turbulent grain suspension and, commonly, bed‐load transport and deposition (M₁). Mud was apparently transported largely as hydrodynamically silt‐ to sand‐sized grains. As the flows waned, both mud and mineral grains settled, increasing near‐bed grain concentration and flow density. Low‐density mud grains settling into the denser near‐bed layers were trapped because of their reduced settling velocities, whereas denser quartz and feldspar continued settling to the bed. The result of this kinetic sieving was an increasing mud content and particle concentration in the near‐bed layers. Disaggregation of mud grains in the near‐bed zone as a result of intense shear and abrasion against rigid mineral grains caused a rapid increase in effective clay surface area and, hence, near‐bed cohesion, shear resistance and viscosity. Eventually, turbulence was suppressed in a layer immediately adjacent to the bed, which was transformed into a cohesion‐dominated viscous sublayer. The banding and lamination in M₂ are thought to reflect the formation, evolution and deposition of such cohesion‐dominated sublayers. More rapid fallout from suspension in less muddy flows resulted in the development of thin, short‐lived viscous sublayers to form wispy laminated divisions (M₃) and, in the least muddy flows with the highest suspended‐load fallout rates, direct suspension sedimentation formed dish‐structured M₄ divisions. Markov chain analysis indicates that these divisions are stacked to form a range of bed types: (I) dish‐structured beds; (II) dish‐structured and wispy laminated beds; (III) banded, wispy laminated and/or dish‐structured beds; (IV) predominantly banded beds; and (V) thickly banded and mixed slurried beds. These different bed types form mainly in response to the varying mud contents of the depositing flows and the influence of mud on suspended‐load fallout rates. The Britannia sandstones provide a remarkable and perhaps unique window on the mechanics of sediment‐gravity flows transitional between turbidity currents and debris flows and the textures and structuring of their deposits.     

四川凉山州美姑县61泥石流灾害研究

四川凉山州美姑县6.1泥石流灾害实例研究表明,该泥石流约为20年一遇的中小规模的泥石流。流域上游短历时强降雨和冰雹天气过程是这次泥石流暴发的诱因,流域内退化的生态环境和中下两岸不稳定边坡以及沟道内大量的松散堆积物为这次泥石流提供了丰富的固体物质来源。泥石流堆积物具有典型的多峰型粒度特征,且有较高的粘粒含量。巨大的泥石流漂砾、石背石现象、龟裂现象、侧积堤和龙头堆积证实了这次泥石流为粘性泥石流。危险度评价表明,采莫洛沟属于高度危险的泥石流沟,危险度为0.67;乃托沟属于中度危险的泥石流沟,危险度为0.58。风险评估结果可知,两沟都属于泥石流高风险区风险度分别为0.52和0.45。高风险区的泥石流灾害给当地的经济社会造成了严重影响并直接造成了较大的人员伤亡和财产损失。     

Geologic,geomorphic, and meteorological aspects of debris flows triggered by Hurricanes Frances and Ivan during September 2004 in the Southern Appalachian Mountains of Macon County,North Carolina (southeastern USA)

In September 2004, rain from the remnants of Hurricanes Frances and Ivan triggered at least 155 landslides in the Blue Ridge Mountains of North Carolina. At least 33 debris flows occurred in Macon County, causing 5 deaths, destroying 16 homes, and damaging infrastructure. We mapped debris flows and debris deposits using a light-detecting and ranging digital elevation model, remote imagery and field studies integrated in a geographic information system. Evidence of past debris flows was found at all recent debris flow sites. Orographic rainfall enhancement along topographic escarpments influenced debris flow frequency at higher elevations. A possible trigger for the Wayah and fatal Peeks Creek debris flows was a spiral rain band within Ivan that moved across the area with short duration rainfall rates of 150–230 mm/h. Intersecting bedrock structures in polydeformed metamorphic rock influence the formation of catchments within structural–geomorphic domains where debris flows originate.     

Petrology of the prehistoric lavas and dyke of the Barren Island,Andaman Sea,Indian Ocean

Although Barren Island (Andaman Sea, Indian Ocean) witnessed several volcanic eruptions during historic times, the eruptions that led to the formation of this volcanic island occurred mainly during prehistoric times. It is still active and currently in the fumarolic stage. Its volcanic evolution appears to be characterized by a constructive phase with the piling up of lava flows and scoria deposits and Strombolian activities, followed by a sudden collapse of the main cone. Deposits of a possible caldera-forming eruption were not recognized earlier. After a period of peri-calderic hydromagmatic activity, whose deposits presently mantle inner and outer caldera walls, a new phase of intracalderic Vulcanian activities took place. A prominent dyke in the SE inner side of the caldera wall was recognized. Petrographically the lava flows and dyke are similar but they differ in their chemical composition (viz., SiO₂, MgO, Ni, Cr) significantly. Similarity in major, minor and trace element composition (viz., K/La, K/Nb, K/Rb, K/Ti ratios) of these rocks together with Chondrite normalized trace element (Rb, Ba, Sr, P, Zr, Ti and Nb) and REE (La, Ce, Nd and Y) patterns of the Barren Island prehistoric lava flows and dyke and low-K lavas of Sunda Arc indicates that Barren Island must have evolved from a source similar to that of Sunda Arc lavas during the Quaternary Period.     

Sedimentology of the debris-flow-dominated Warm Spring Canyon alluvial fan, Death Valley, California

Facies analysis of widely distributed exposures of the 32·6 km² and 8·1-km-long Warm Spring Canyon fan, central Death Valley, shows that it has been built principally by debris-flow deposits. These deposits were derived from a mature Panamint Range catchment mostly underlain by Precambrian mudrock, quartzite and dolomite. Stacked, clast-rich and matrix-supported debris-flow lobes of slightly bouldery, muddy, pebble–cobble gravel in beds 20–150 cm thick dominate the fan from apex to toe, accounting for 75–98% of most exposures. Interstratified with the debris flows are less abundant (2–25% of cuts), thinner (5–30 cm) and more discontinuous beds of clast-supported and imbricated, pebble–cobble gravel deposited by overland flows and gully flows. This facies formed by the surficial fine-fraction water winnowing of the debris flows primarily during recessional flood stage of the debris-flow events. Two other facies associations make up a small part of the fan. The incised-channel tract consists of a 250-m-wide clast-supported ribbon of irregularly to thickly bedded, boulder, pebble, cobble gravel nested within debris-flow deposits. This channel fill is oriented generally perpendicular to the Panamint range front. It formed by extensive erosion and winnowing of debris flows deposited within the incised channel, into which all water discharge from the catchment is funnelled. The limited presence of this facies only straddling the present incised channel indicates that this channel overall has maintained a consistent position on the fan except for slight lateral shifts, some caused by strike-slip offset. Fault offset temporarily closed the upper incised channel, causing recessional debris-flow mud to be ponded behind the dam. The other local facies assemblage consists of subrounded to rounded, moderately sorted pebble gravel in low-angle cross-beds that slope both basinwards and fanwards. This gravel was deposited in beachface, backshore and shoreface barrier-spit environments that developed where Lake Manly impinged on the Warm Spring fan during late Pleistocene time. These deposits straddle headcuts into, and were derived from, erosion of the debris-flow deposits. Wave energy sorted finer sediment from the shore zone, concentrated coarser sediment and rounded the coarse to very coarse pebble fraction by selective reworking.     

Cause of dominance by sheetflood vs. debris-flow processes on two adjoining alluvial fans, Death Valley, California

Two large, adjoining alluvial fans of the Panamint Range piedmont, Death Valley, California, are composed of different facies assemblages deposited by contrasting sedimentary processes. The Anvil Spring fan was built solely by water-flow processes (incised-channel floods and sheetfloods), whereas the neighbouring Warm Spring fan has been constructed principally by debris flows. The boundary between these fans delineates a sharp provincial piedmont contact between sheetflood-dominated fans to the south and debris-flow-dominated fans to the north. Factors such as climate, catchment area, fan area, catchment relief, aspect, vegetation types and density, and neotectonic setting are essentially identical for these two fans. The key difference between them is that their catchments are underlain by dissimilar bedrock types, which weather to yield distinctive sediment suites. Weathering of the granite and andesite of the Anvil fan catchment produces significant volumes of medium to very coarse sand, granules, pebbles, cobbles and boulders, but minimal silt and clay. In contrast, the shale, quartzite and dolomite that dominate bedrock in the Warm Spring catchment weather to yield a wide suite of sedimentary particles spanning from clay to boulders. The abundance of mud, and the unsorted character of the yielded sediment, cause precipitation-induced slope failures in the Warm Spring catchment to transform readily into debris flows. This propensity is due to the low permeability of the colluvial sediment, which causes added water to become trapped quickly and pore pressure to rise rapidly, promoting transformations to debris flows. In contrast, the limited volume of sediment finer than medium sand yielded from the Anvil fan catchment causes the colluvium to have high permeability. This factor prevents the transformation of wet colluvium to a debris flow during hydrologically triggered slope failures, instead maintaining sediment transport as entrained bed load or suspended load in a water flow.     

The Zymoetz River landslide, British Columbia, Canada: description and dynamic analysis of a rock slide–debris flow

The Zymoetz River landslide is a recent example of an extremely mobile type of landslide known as a rock slide–debris flow. It began as a failure of 900,000 m³ of bedrock, which mobilized an additional 500,000 m³ of surficial material in its path, transforming into a large debris flow that traveled over 4 km from its source. Seasonal snow and meltwater in the proximal part of the path were important factors. A recently developed dynamic model that accounts for material entrainment, DAN3D, was used to back-analyze this event. The two distinct phases of motion were modeled using different basal rheologies: a frictional model in the proximal path and a Voellmy model in the distal path, following the initiation of significant entrainment. Very good agreement between the observed and simulated results was achieved, suggesting that entrainment capabilities are essential for the successful simulation of this type of landslide.     

The September 8–9, 1998 Rain-Triggered Flood Events at Motozintla, Chiapas, Mexico

In September 1998 tropical storm “Earl” swept southern Mexico, producing intense rainfall in the states of Oaxaca and Chiapas. Among the most devastated cities was Motozintla, located in the drainage basin of the Allende, La Mina and Xelajú Grande Rivers. The rainfall from the tropical storm totaled 175 mm on September 8 and 130 mm on September 9, duplicating in two days the average monthly precipitation in the region. Numerous landslides occurred in the vicinity of Motozintla, depositing large volumes of material into the Xelajú Grande stream. Much of this sediment was subsequently remobilized, yielding debris flows, hyperconcentrated flows, and sediment-laden flows that inundated most sections of Motozintla city. The flows covered an approximate area of 3.15 km² with a minimum volume of 4.4 × 10⁶ m³ of sediment. Communication of Motozintla with the rest of the Chiapas State was interrupted for about a month, as was the supply of potable water, food, electricity, and fuel. The geologic record around Motozintla indicates that the Xelajú Grande River has been a pathway for similar large floods during the last 6000 years. The oldest deposit yielded a radiocarbon age of 5320 ± 100 ¹⁴C years. B.P. At least two historic floods have occurred during the last 100 years, a time period defined by a stratigraphically distinct tephra of 1902. Frequency analysis of the historical record of daily rainfall in the Motozintla area suggests that events like that of September, 1998, have a recurrence interval of about 25 years. After the catastrophic flows of 1998, the mitigation measures by Municipal Authorities were made without regard to geological and environmental factors, or to taking into consideration the flow magnitude and appropriate hazard-mitigation techniques, with the result that Motozintla remains at serious risk for future floods. Unfortunately, prior to the publication of this study, in early October 2005, Motozintla was seriously damaged again by intense rain provoked by Hurricane Stan.     

甘肃龙首山新元古代烧火筒群沉积特征及其构造意义

华北地块西南缘龙首山隆起广布一套前寒武纪碳酸盐质为主要成分组成的碎屑流沉积,近年来发现在邻区北山、祁连山地区亦有分布。岩石状貌特殊,砾石大小混杂,呈无磨圆的棱角、半棱角状,为杂基支撑结构。区域上岩层连续性好,但厚薄不一,厚几米至几十米,局部与火山岩相变。根据其上覆、下伏岩层同位素年龄和微古植物化石定年资料,分析判断为新元古代中晚期的产物,讨论其成因为大陆裂谷沉积构造环境下,地壳急剧动荡,崩塌原稳定台地相的沉积,大量崩塌堆积物在大陆裂谷斜坡形成碎屑流移动而成。其为大陆裂谷的典型沉积,具有重要的指相意义。龙首山及邻区新元古代中晚期大面积碎屑流沉积分布,表证当时大规模大陆裂谷作用的发生,与全球性Rodinia大陆裂解的认识一致.     

Fractionation modelling of segregations in the Toomba Basalt,north Queensland

Segregations that are darker than their host basalt are locally common in the Late Pleistocene Toomba Basalt flow northwest of Charters Towers. At Basalt Corner this flow has been inflated to a thickness of 17 m and segregations are displayed in pipes, sheets, veins and vesicles. Their chemical compositions are distinct from the host hawaiite and least‐square mixing solutions provide close models involving crystallisation of olivine, plagioclase, augite and magnetite in the cooling host basalt and gas‐pressure extraction of residual melt to form the segregations. Trace‐element concentrations are consistent with this mechanism and can, in general, be modelled using mineral partition coefficients from the literature. Segregations may concentrate near the edges of the inflation structures.     

Velocity and runout simulation of destructive debris flows and debris avalanches in pyroclastic deposits,Campania region,Italy

The Campanian Apennines are characterized by the presence of monocline ridges, mainly formed by limestone. During the periods of volcanic activity of the Somma-Vesuvius and Phlegrean Fields, the ridges were mantled with pyroclastic materials in varying thickness. The pyroclastics have been involved in destructive landslides both in historical time and in the recent past (1997, 1998, 1999). The landslides occur following intense and prolonged rainfalls. In some cases, landslides extended up to 4 km into the surrounding lowlands and reached towns, causing severe destruction and over 200 deaths. Generally, the landslides begin as small debris slides that develop into large, shallow debris avalanches or debris flows involving pyroclastic horizons and colluvial soils (0.5–2 m thick) on steep and vegetated slopes, often at the heads of gullies. During motion, the landslide materials eroded vegetation and soils from the slope, so that the moving material volume tended to increase. Then, proceeding towards and beyond the base of the slopes, the phenomena evolved into hyperconcentrated streamflow due to dilution by incorporating water. The results of motion analyses are described. An empirical rheological relationship was used including two principal terms that depend on the total normal stress and on the flow velocity. On this basis, the model has simulated the velocity and duration of debris avalanches and the distribution of the deposits. The selected areas were those of Sarno/Quindici and Cervinara, where a large amount of data is available both on the material properties and geomorphological setting. It was found that the majority of the cases at the two sites can be simulated successfully with only one specific pair of rheologic parameters. This provides the possibility for first-order predictions to be made of the motion of future landslides. Such predictions will be a valuable tool for outlining potential hazard areas and designing remedial measures.     

Rain-induced debris and mudflow triggering factors assessment in the Santiago cordilleran foothills,Central Chile

Debris and mudflows are some of the main geological hazards in the mountain foothills of the Chilean capital city of Santiago. There, the risk of flows triggered in the basins of ravines that drain the range into the city increases with time due to the city growth. A multivariate statistical study based on the logistic regression method is presented. The model provides equations that allow the computation of combined meteorological triggering factors associated with a probability of rain-induced flow occurrence. Daily rainfall, accumulated rainfall and the snowfall level, traditionally considered as the relevant factors, are analysed for a 25-year period. The results show a strong relevance of the rainfall on the day of the flow event over the other factors. However, the relatively low probabilities returned for some real flow events suggest that the model does not capture all the significant variables and the problem is more complex than as it has been traditionally assumed, and further investigations are needed to develop predictive models of flow triggering.     

Example of a debris-flow risk analysis from Vancouver Island,British Columbia,Canada

In July 2005, a debris flow and a water flood occurred on two adjacent gullies in the White River area, on northern Vancouver Island in British Columbia, Canada. The 16,000 m³ debris flow buried approximately 7.5 ha of second-growth trees, buried approximately 500 m of a forestry road, and reached two fish-bearing streams. The water flood eroded approximately 240 m of the same forestry road and plugged four culverts before overtopping and inundating the road. To better plan for future events, risk analyses of debris flows, debris floods, and water floods were carried out for the two gullies involved, plus a third adjacent gully. The elements at risk that were analyzed included, in order of priority: users of the forestry road, the fish-bearing streams, the forestry road itself, and a timber bridge. Using a series of qualitative, but defined, relative-risk matrices, the following components of specific risk were estimated for each of the three types of events on each of the three gullies for each of the four elements at risk: probability of occurrence, probability that the event will reach or otherwise affect the site of the element at risk, the probability that the element at risk will be at the site when the event occurs, and the probability of loss or damage resulting from the element being at the site when the event occurs.