Tailings composition effects on shear strength behavior of co-mixed mine waste rock and tailings

The objective of this study was to evaluate the effect of mine tailings composition on shear behavior and shear strength of co-mixed mine waste rock and tailings (WR&T). Crushed gravel was used as a synthetic waste rock and mixed with four types of tailings: (1) fine-grained garnet, (2) coarse-grained garnet, (3) copper, and (4) soda ash. Co-mixed WR&T specimens were prepared to target mixture ratios of mass of waste rock to mass of tailings (R) such that tailings “just filled” interparticle void space of the waste rock (i.e., optimum mixture ratio, R _opt). Triaxial compression tests were conducted on waste rock, tailings, and mixed waste at effective confining stresses (\(\sigma_{\text{c}}^{{\prime }}\)) ranging from 5 to 40 kPa to represent stresses anticipated in final earthen covers for waste containment facilities. Waste rock and co-mixed WR&T specimens were 150 mm in diameter by 300 mm tall, whereas tailings specimens were 38 mm in diameter by 76 mm tall. Shear strength was quantified using effective stress friction angles (?′) from undrained tests: ?′ for waste rock was 37°, ?′ for tailings ranged from 34° to 41°, and ?′ for WR&T mixtures ranged from 38° to 40°. Thus, shear strength of co-mixed WR&T was comparable to waste rock regardless of tailings composition. Shear behavior of WR&T mixtures was a function of R and tailings composition. Tailings influenced shear behavior for R < R _opt and when tailings predominantly were silt. Shear behavior was influenced by waste rock for R ≥ R _opt and when tailings predominantly were sand or included clay particles.     

New insights on pressure,temperature, and chemical stability of CsAlSi<Subscript>5</Subscript>O<Subscript>12</Subscript>, a potential host for nuclear waste

A Cs-bearing polyphase aggregate with composition (in wt%): 76(1)_CsAlSi5O12 + 7(1)_CsAlSi2O6 + 17(1)_amorphous, was obtained from a clinoptilolite-rich epiclastic rock after a beneficiation process of the starting material (aimed to increase the fraction of zeolite to 90 wt%), cation exchange and then thermal treatment. CsAlSi₅O₁₂ is an open-framework compound with CAS topology; CsAlSi₂O₆ is a pollucite-like material with ANA topology. The thermal stability of this polyphase material was investigated by in situ high-T X-ray powder diffraction, the combined P–T effects by a series of runs with a single-stage piston cylinder apparatus, and its chemical stability following the “availability test” (“AVA test”) protocol. A series of additional investigations were performed by WDS–electron microprobe analysis in order to describe the P–T-induced modification of the material texture, and to chemically characterize the starting material and the run products. The “AVA tests” of the polyphase aggregate show an extremely modest release of Cs⁺: 0.05 mg/g. In response to applied temperature and at room P, CsAlSi₅O₁₂ experiences an unquenchable and displacive Ama2-to-Amam phase transition at about 770 K, and the Amam polymorph is stable in its crystalline form up to 1600 K; a crystalline-to-amorphous phase transition occurs between 1600 and 1650 K. In response to the applied P = 0.5 GPa, the crystalline-to-amorphous transition of CsAlSi₅O₁₂ occurs between 1670 and 1770 K. This leads to a positive Clapeyron slope (i.e., dP/dT > 0) of the crystalline-to-amorphous transition. When the polyphase aggregate is subjected at P = 0.5 GPa and T > 1770 K, CsAlSi₅O₁₂ melts and only CsAlSi₂O₆ (pollucite-like; dominant) and Cs-rich glass (subordinate) are observed in the quenched sample. Based on its thermo-elastic behavior, P–T phase stability fields, and Cs⁺ retention capacity, CsAlSi₅O₁₂ is a possible candidate for use in the immobilization of radioactive isotopes of Cs, or as potential solid hosts for ¹³⁷Cs γ-radiation source in sterilization applications. More in general, even the CsAlSi₅O₁₂-rich aggregate obtained by a clinoptilolite-rich epiclastic rock appears to be suitable for this type of utilizations.     

Electron paramagnetic resonance studies on clinochlore from Longitudinal Valley area,northeastern Taiwan

A natural sample of clinochlore from the Longitudinal Valley area of northeastern Taiwan has been characterized by using the powder X-ray diffraction (XRD), differential thermal analysis and electron paramagnetic resonance (EPR) spectroscopic techniques. The lattice parameters of the monoclinic (IIb) clinochlore with the composition (Mg_2.988 Al_1.196 Fe_1.6845 Mn_0.026)_5.8945 (Si_2.559 Al_1.441)₄ O₁₀ (OH)₈ have been calculated from the powder XRD data and are found to be a = 5.347 Å, b = 9.223 Å, c = 14.250 Å, β = 97.2° and Z = 2. The thermal behaviour of the sample showed the typical behaviour of clinochlore with a hydroxyl content of 12.5 wt%. The EPR spectrum at room temperature exhibits two resonance signals centred at g ≈ 2.0 and g ≈ 8.0. The signal at g ≈ 2.0 shows a six-line hyperfine structure which is a characteristic of Mn²⁺ ions in octahedral symmetry. The resonance signal at g ≈ 8.0 is a characteristic of Fe³⁺ ions. The EPR spectra have also been recorded at different temperatures (123–295 K). The population of spin levels (N) has been calculated for g ≈ 2.0 and g ≈ 8.0 resonance signals. It is observed that N increases with decreasing temperature. From EPR spectra, the spin-Hamiltonian parameters have been evaluated. The zero-field splitting parameter (D) is found to be temperature dependent. The peak-to-peak width of the g ≈ 8.0 resonance signal is found to increase with decrease in temperature.     

Behavior of 10-Å phase at low temperatures

The thermal evolution of 10-Å phase Mg₃Si₄O₁₀(OH)₂·H₂O, a phyllosilicate which may have an important role in the storage/release of water in subducting slabs, was studied by X-ray single-crystal diffraction in the temperature range 116–293 K. The lattice parameters were measured at several intervals both on cooling and heating. The structural model was refined with intensity data collected at 116 K and compared to the model refined at room temperature. As expected for a layer silicate on cooling in this temperature range, the a and b lattice parameters undergo a small linear decrease, α _a  = 1.7(4) 10^?6 K^?1 and α _b  = 1.9(4) 10^?6 K^?1, where α is the linear thermal expansion coefficient. The greater variation is along the c axis and can be modeled with the second order polynomial c _T  = c ₂₉₃(1 + 6.7(4)10^?5 K^?1ΔT + 9.5(2.5)10^?8 K^?2(ΔT)²) where ΔT = T ? 293 K; the monoclinic angle β slightly increased. The cell volume thermal expansion can be modeled with the polynomial V _T  = V ₂₉₃ (1 + 8.0 10^?5 K^?1 ΔT + 1.4 10^?7 K^?2 (ΔT)²) where ΔT = T ? 293 is in K and V in ų. These variations were similar to those expected for a pressure increase, indicating that T and P effects are approximately inverse. The least-squares refinement with intensity data measured at 116 K shows that the volume of the SiO₄ tetrahedra does not change significantly, whereas the volume of the Mg octahedra slightly decreases. To adjust for the increased misfit between the tetrahedral and octahedral sheets, the tetrahedral rotation angle α changes from 0.58° to 1.38°, increasing the ditrigonalization of the silicate sheet. This deformation has implications on the H-bonds between the water molecule and the basal oxygen atoms. Furthermore, the highly anisotropic thermal ellipsoid of the H₂O oxygen indicates positional disorder, similar to the disorder observed at room temperature. The low-temperature results support the hypothesis that the disorder is static. It can be modeled with a splitting of the interlayer oxygen site with a statistical distribution of the H₂O molecules into two positions, 0.6 Å apart. The resulting shortest O_bas–O_W distances are 2.97 Å, with a significant shortening with respect to the value at room temperature. The low-temperature behavior of the H-bond system is consistent with that hypothesized at high pressure on the basis of the Raman spectra evolution with P.     

Synthesis,TEM characterization and thermal behaviour of LiNiSi<Subscript>2</Subscript>O<Subscript>6</Subscript> pyroxene

A pyroxene with composition LiNiSi₂O₆ was synthesized at T = 1,473 K and P = 2.0 GPa; the cell parameters at T = 298 K are a = 9.4169(6) Å, b = 8.4465(7) Å, c = 5.2464(3) Å, β = 110.534(6)°, V = 390.78(3) Å³. TEM examination of the LiNiSi₂O₆ pyroxene showed the presence of h + k odd reflections indicative of a primitive lattice, and of antiphase domains obtained by dark field imaging of the h + k odd reflections. A HT in situ investigation was performed by examining TEM selected area diffraction patterns collected at high temperature and synchrotron radiation powder diffraction. In HTTEM the LiNiSi₂O₆ was examined together with LiCrSi₂O₆ pyroxene. In LiCrSi₂O₆ the h + k odd critical reflections disappear at about 340 K; they are sharp up to the transition temperature and do not change their shape until they disappear. In LiNiSi₂O₆ the h + k odd reflections are present up to sample deterioration at 650 K. A high temperature synchrotron radiation powder diffraction investigation was performed on LiNiSi₂O₆ between 298 and 773 K. The analysis of critical reflections and of changes in cell parameters shows that the space group is P-centred up to the highest temperature. The comparative analysis of the thermal and spontaneous strain contributions in P2₁/c and C2/c pyroxenes indicates that the high temperature strain in P-LiNiSi₂O₆ is very similar to that due to thermal strain only in C2/c spodumene and that a spontaneous strain contribution related to pre-transition features is not apparent in LiNiSi₂O₆. A different high-temperature behaviour in LiNiSi₂O₆ with respect to other pyroxenes is suggested, possibly in relation with the presence of Jahn–Teller distortion of the M1 polyhedron centred by low-spin Ni³⁺.     

Detailed comparison of nine intact rock failure criteria using polyaxial intact coal strength data obtained through PFC<Superscript>3D</Superscript> simulations

Study of intact rock failure criteria is an important topic in rock mechanics. In this study, applicability of nine different intact rock failure criteria is investigated for intact coal strength data. PFC^3D modeling was used to simulate the laboratory polyaxial tests for cubic intact coal blocks of side dimension 110 mm under different confining stress combinations. A modified grid search procedure is proposed and used to find the best-fitting parameter values and to calculate the coefficient of determination (R ²) values for each criterion. Detailed comparisons of the nine criteria are made using the following aspects: R ² values, σ ₁ ? σ ₂ plots for different σ ₃, shapes on the deviatoric plane, linearity or nonlinearity on the meridian planes. Through the comparisons of R ² values, σ ₁ ? σ ₂ plots and meridian lines, the modified Wiebols–Cook and modified Lade criteria were found to fit the intact coal strength data best. The nine failure criteria are categorized into three types based on the appearances on the deviatoric plane.     

Thermal equation of state of natural tourmaline at high pressure and temperature

Synchrotron-based in situ angle-dispersive X-ray diffraction experiments were conducted on a natural uvite-dominated tourmaline sample by using an external-heating diamond anvil cell at simultaneously high pressures and temperatures up to 18 GPa and 723 K, respectively. The angle-dispersive X-ray diffraction data reveal no indication of a structural phase transition over the P–T range of the current experiment in this study. The pressure–volume–temperature data were fitted by the high-temperature Birch–Murnaghan equation of state. Isothermal bulk modulus of K ₀ = 96.6 (9) GPa, pressure derivative of the bulk modulus of \(K_{0}^{\prime } = 12.5 \;(4)\), thermal expansion coefficient of α ₀ = 4.39 (27) × 10^?5 K^?1 and temperature derivative of the bulk modulus (?K/?T) _P  = ?0.009 (6) GPa K^?1 were obtained. The axial thermoelastic properties were also obtained with K _a0 = 139 (2) GPa, \(K_{a0}^{\prime }\) = 11.5 (7) and α _a0 = 1.00 (11) × 10^?5 K^?1 for the a-axis, and K _c0 = 59 (1) GPa, \(K_{c0}^{\prime }\) = 11.4 (5) and α _c0 = 2.41 (24) × 10^?5 K^?1 for the c-axis. Both of axial compression and thermal expansion exhibit large anisotropic behavior. Thermoelastic parameters of tourmaline in this study were also compared with that of the other two ring silicates of beryl and cordierite.     

Testing Study of Subcritical Crack Growth Mechanism During Water Rock Interaction

Subcritical crack growth plays an important role in evaluating the long-term stability of structures in rocks. By applying the constant-displacement-relax method, two groups of test specimens that one immersed in groundwater and the other in air were tested to get the parameters of subcritical crack growth in double torsion test. The relations of the stress intensity factor K _I versus the subcritical crack growth velocity V were obtained under the two different environments, and the behavior of subcritical crack growth was also analyzed. The results showed: the relations of lg K _I  ? lg V accorded with linear rules, which is in good agreement with Charles theory; Compared with specimens in nature state, the lg K _I  ? lg V curves of saturated water specimens locate top left comer of those of air specimens. The slope of curve is smaller, and the intercept is bigger, which shows that the water–rock interaction speeds up the subcritical crack growth. And A increases 2.9 × 10¹⁸ folds but n decreases from 85.12 to 40.83 because of the water–rock interaction. Meanwhile, the fracture toughness K _IC also decreases obviously from 2.55 in air to 2.26 in water due to water rock interaction. The testing results provide a basis for time-dependence of rock engineering stability.     

A modified normalized model for predicting effective soil thermal conductivity

Effective soil thermal conductivity (λ _eff) describes the ability of a multiphase soil to transmit heat by conduction under unit temperature gradient. It is a critical parameter for environmental science, earth and planetary science, and engineering applications. Numerous models are available in the literature, but their applicability is generally restricted to certain soil types or water contents (θ). The objective of this study was to develop a new model in the similar form of the Johansen 1975 model to simulate the λ _eff(θ) relationship of soils of various soil textures and water contents. An exponential type model with two parameters is developed and a new function for calculating dry soil thermal conductivity is presented. Performance of the new model and six other normalized models were evaluated with published datasets. The results show that the new model is able to well mimic λ _eff(θ) relationship of soils from sand to silt loam and from oven dry to full saturation. In addition, it has the best performance among the seven models under test (with root-mean-square error of 0.059 W m^?1 °C^?1, average deviations of 0.0009 W m^?1 °C^?1, and Nash–Sutcliffe efficiency of 0.994). The new model has potential to improve the reliability of soil thermal conductivity estimation and be incorporated into numerical modeling for environmental, earth and engineering studies.     

The thermal expansion and crystal structure of mirabilite (Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>·10D<Subscript>2</Subscript>O) from 4.2 to 300 K,determined by time-of-flight neutron powder diffraction

We have collected high resolution neutron powder diffraction patterns from Na₂SO₄·10D₂O over the temperature range 4.2–300 K following rapid quenching in liquid nitrogen, and over a series of slow warming and cooling cycles. The crystal is monoclinic, space-group P2₁/c (Z = 4) with a = 11.44214(4) Å, b = 10.34276(4) Å, c = 12.75486(6) Å, β = 107.847(1)°, and V = 1436.794(8) Å³ at 4.2 K (slowly cooled), and a = 11.51472(6) Å, b = 10.36495(6) Å, c = 12.84651(7) Å, β = 107.7543(1)°, V = 1460.20(1) Å³ at 300 K. Structures were refined to R _P (Rietveld powder residual, \( R_{P} = {{\sum {\left| {I_{\text{obs}} - I_{\text{calc}} } \right|} } \mathord{\left/ {\vphantom {{\sum {\left| {I_{\text{obs}} - I_{\text{calc}} } \right|} } {\sum {I_{\text{obs}} } }}} \right. \kern-\nulldelimiterspace} {\sum {I_{\text{obs}} } }} \)) better than 2.5% at 4.2 K (quenched and slow cooled), 150 and 300 K. The sulfate disorder observed previously by Levy and Lisensky (Acta Cryst B34:3502–3510, 1978) was not present in our specimen, but we did observe changes with temperature in deuteron occupancies of the orientationally disordered water molecules coordinated to Na. The temperature dependence of the unit-cell volume from 4.2 to 300 K is well represented by a simple polynomial of the form V = ? 4.143(1) × 10^?7 T ³ + 0.00047(2) T² ? 0.027(2) T + 1437.0(1) Å³ (R ² = 99.98%). The coefficient of volume thermal expansion, α _V , is positive above 40 K, and displays a similar magnitude and temperature dependence to α _V in deuterated epsomite and meridianiite. The relationship between the magnitude and orientation of the principal axes of the thermal expansion tensor and the main structural elements are discussed; freezing in of deuteron disorder in the quenched specimen affects the thermal expansion, manifested most obviously as a change in the behaviour of the unit-cell parameter β.     

Thermoelastic properties of chromium oxide Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> (eskolaite) at high pressures and temperatures

A new synchrotron X-ray diffraction study of chromium oxide Cr₂O₃ (eskolaite) with the corundum-type structure has been carried out in a Kawai-type multi-anvil apparatus to pressure of 15 GPa and temperatures of 1873 K. Fitting the Birch–Murnaghan equation of state (EoS) with the present data up to 15 GPa yielded: bulk modulus (K _0,T0), 206 ± 4 GPa; its pressure derivative K′_0,T , 4.4 ± 0.8; (?K _0,T /?T) = ?0.037 ± 0.006 GPa K^?1; a = 2.98 ± 0.14 × 10^?5 K^?1 and b = 0.47 ± 0.28 × 10^?8 K^?2, where α _0,T  = a + bT is the volumetric thermal expansion coefficient. The thermal expansion of Cr₂O₃ was additionally measured at the high-temperature powder diffraction experiment at ambient pressure and α _0,T0 was determined to be 2.95 × 10^?5 K^?1. The results indicate that coefficient of the thermal expansion calculated from the EoS appeared to be high-precision because it is consistent with the data obtained at 1 atm. However, our results contradict α ₀ value suggested by Rigby et al. (Brit Ceram Trans J 45:137–148, 1946) widely used in many physical and geological databases. Fitting the Mie–Grüneisen–Debye EoS with the present ambient and high-pressure data yielded the following parameters: K _0,T0 = 205 ± 3 GPa, K′_0,T  = 4.0, Grüneisen parameter (γ ₀) = 1.42 ± 0.80, q = 1.82 ± 0.56. The thermoelastic parameters indicate that Cr₂O₃ undergoes near isotropic compression at room and high temperatures up to 15 GPa. Cr₂O₃ is shown to be stable in this pressure range and adopts the corundum-type structure. Using obtained thermoelastic parameters, we calculated the reaction boundary of knorringite formation from enstatite and eskolaite. The Clapeyron slope (with \({\text{d}}P/{\text{d}}T = - 0.014\) GPa/K) was found to be consistent with experimental data.     

The Effect of High Temperature on Tensile Strength and Damage Characteristics of Limestone

In this paper, the limestone specimens are heated from room temperature 25 to 800 °C in a high temperature furnace and then are subjected to Brazilian test with the AG-I250 electronic precision material testing machine. The physical properties, mechanical properties, disc failure pattern, energy absorbed per unit area and damage characteristics of disc are comprehensively investigated. The results show that: with the increase of temperature, the changing trends of tensile strength, peak strain, tensile modulus and accumulated energy absorbed per unit area of disc are similar, they are first increases, then decrease, the energy consumption index is consistent with the macroscopic damage characteristics; the value of ε_s increase first and then reduce, reaches the maximum at 600 °C. The value of n is increasing and fluctuating, but the change trend of D_c is opposite, which is decreasing and fluctuating. The slope of the damage variable-strain curves decreases first and then increases, the minimum value at 600 °C. This study is of significance to the prediction and evaluation of the stability and safety of rock mass post-high temperature.     

Argon retention properties of silicate glasses and implications for <Superscript>40</Superscript>Ar/<Superscript>39</Superscript>Ar age and noble gas diffusion studies

Sized aggregates of glasses (47–84 wt% SiO₂) were fused from igneous-derived cohesive fault rock and igneous rock, and step-heated from ~400 to >1,200 °C to obtain their ³⁹Ar diffusion properties (average E=33,400 cal mol^?1; D _o=4.63×10^?3 cm² s^?1). At T<~1,000 °C, glasses containing <~69 wt% SiO₂ and abundant network-forming cations (Ca, Fe, Mg) reveal moderate to strong non-linear increases in D and E, reflecting structural modifications as the solid transitions to melt. Extrapolation of these Arrhenius properties down to typical geologic T-t conditions could result in a 1.5 log₁₀ unit underestimation in the diffusion rate of Ar in similar materials. Numerical simulations based upon the diffusion results caution that some common geologic glasses will likely yield ⁴⁰Ar/³⁹Ar cooling ages rather than formation ages. However, if cooling rates are sufficiently high, ambient temperatures are sufficiently low (e.g., <65–175 °C), and coarse particles (e.g., radius (r) >~1 mm) are analyzed, glasses with compositions similar to ours may preserve their formation ages.     

The crystal structure and thermal expansion tensor of MgSO<Subscript>4</Subscript>–11D<Subscript>2</Subscript>O(meridianiite) determined by neutron powder diffraction

We have collected high-resolution neutron powder diffraction patterns from MgSO₄·11D₂O over the temperature range 4.2–250 K. The crystal is triclinic, space-group \( \text{P} \bar{1} \) (Z = 2) with a = 6.72746(6) Å, b = 6.78141(6) Å, c = 17.31803(13) Å, α = 88.2062(6)°, β = 89.4473(8)°, γ = 62.6075(5)°, and V = 701.140(6) ų at 4.2 K, and a = 6.75081(3) Å, b = 6.81463(3) Å, c = 17.29241(6) Å, α = 88.1183(3)°, β = 89.4808(3)°, γ = 62.6891(3)°, and V = 706.450(3) ų at 250 K. Structures were refined to wRp = 3.99 and 2.84% at 4.2 and 250 K, respectively. The temperature dependence of the lattice parameters over the intervening range have been fitted with a modified Einstein oscillator model which was used to obtain the coefficients of the thermal expansion tensor. The volume thermal expansion, α_V, is considerably smaller than ice Ih at all temperatures, and smaller even than MgSO₄·7D₂O (although ?α_V/?T is very similar for both sulfates); MgSO₄·11D₂O exhibits negative α_V below 55 K (compared to 70 K in D₂O ice Ih and 20 K in MgSO₄·7D₂O) The relationship between the magnitude and orientation of the principal axes of the expansion tensor and the main structural elements are discussed.     

Compressibility of strontium orthophosphate Sr<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> at high pressure

High pressure in situ synchrotron X-ray diffraction experiment of strontium orthophosphate Sr₃(PO₄)₂ has been carried out to 20.0 GPa at room temperature using multianvil apparatus. Fitting a third-order Birch–Murnaghan equation of state to the P–V data yields a volume of V ₀ = 498.0 ± 0.1 Å³, an isothermal bulk modulus of K _T  = 89.5 ± 1.7 GPa, and first pressure derivative of K _T ′ = 6.57 ± 0.34. If K _T ′ is fixed at 4, K _T is obtained as 104.4 ± 1.2 GPa. Analysis of axial compressible modulus shows that the a-axis (K _a  = 79.6 ± 3.2 GPa) is more compressible than the c-axis (K _c  = 116.4 ± 4.3 GPa). Based on the high pressure Raman spectroscopic results, the mode Grüneisen parameters are determined and the average mode Grüneisen parameter of PO₄ vibrations of Sr₃(PO₄)₂ is calculated to be 0.30(2).     

Effect of the activation temperature over activated carbon production from castor cake and its evaluation as dye adsorbent

In this work, castor cake produced as a by-product in castor oil extraction was used for activated carbon production. Castor cake was chemically treated with a K₂CO₃ solution, and the effect of the pyrolysis temperature in the 500–900 °C range was studied. Materials were characterized by X-ray powder diffraction, thermogravimetric analysis, scanning electron microscopy and nitrogen adsorption–desorption at ?196 °C. Methylene blue adsorption was selected as a test probe to stress the removal capacity of the prepared materials. By the X-ray powder diffraction analysis, carbon obtaining in its graphite allotropic form together with other inorganic compounds was verified. Scanning electron microscopy images evidenced the generation of porosity in the thermally treated samples compared with the pristine compound. In addition, the specific surface area values augmented progressively with the thermal treatment increment achieving a value of 1015 m² g^?1 in the 900 °C calcined sample. Calcination at 800 °C and m/V = 0.003 ratio were the best parameter combination to achieve a 99.6% methylene blue uptake.     

The compressibility of Fe- and Al-bearing phase D to 30 GPa

High-pressure in situ X-ray diffraction experiment of Fe- and Al-bearing phase D (Mg_0.89Fe_0.14Al_0.25Si_1.56H_2.93O₆) has been carried out to 30.5 GPa at room temperature using multianvil apparatus. Fitting a third-order Birch–Murnaghan equation of state to the P–V data yields values of V ₀ = 86.10 ± 0.05 ų; K ₀ = 136.5 ± 3.3 GPa and K′ = 6.32 ± 0.30. If K′ is fixed at 4.0 K ₀ = 157.0 ± 0.7 GPa, which is 6% smaller than Fe–Al free phase D reported previously. Analysis of axial compressibilities reveals that the c-axis is almost twice as compressible (K _c  = 93.6 ± 1.1 GPa) as the a-axis (K _a  = 173.8 ± 2.2 GPa). Above 25 GPa the c/a ratio becomes pressure independent. No compressibility anomalies related to the structural transitions of H-atoms were observed in the pressure range to 30 GPa. The density reduction of hydrated subducting slab would be significant if the modal amount of phase D exceeds 10%.     

Sound velocity and elastic properties of Fe–Ni and Fe–Ni–C liquids at high pressure

The sound velocity (V _P) of liquid Fe–10 wt% Ni and Fe–10 wt% Ni–4 wt% C up to 6.6 GPa was studied using the ultrasonic pulse-echo method combined with synchrotron X-ray techniques. The obtained V _P of liquid Fe–Ni is insensitive to temperature, whereas that of liquid Fe–Ni–C tends to decrease with increasing temperature. The V _P values of both liquid Fe–Ni and Fe–Ni–C increase with pressure. Alloying with 10 wt% of Ni slightly reduces the V _P of liquid Fe, whereas alloying with C is likely to increase the V _P. However, a difference in V _P between liquid Fe–Ni and Fe–Ni–C becomes to be smaller at higher temperature. By fitting the measured V _P data with the Murnaghan equation of state, the adiabatic bulk modulus (K _S0) and its pressure derivative (K _S ^′ ) were obtained to be K _S0 = 103 GPa and K _S ^′  = 5.7 for liquid Fe–Ni and K _S0 = 110 GPa and K _S ^′  = 7.6 for liquid Fe–Ni–C. The calculated density of liquid Fe–Ni–C using the obtained elastic parameters was consistent with the density values measured directly using the X-ray computed tomography technique. In the relation between the density (ρ) and sound velocity (V _P) at 5 GPa (the lunar core condition), it was found that the effect of alloying Fe with Ni was that ρ increased mildly and V _P decreased, whereas the effect of C dissolution was to decrease ρ but increase V _P. In contrast, alloying with S significantly reduces both ρ and V _P. Therefore, the effects of light elements (C and S) and Ni on the ρ and V _P of liquid Fe are quite different under the lunar core conditions, providing a clue to constrain the light element in the lunar core by comparing with lunar seismic data.     

On the crystal chemistry and elastic behavior of a phlogopite 3<Emphasis Type="Italic">T</Emphasis>

The crystal chemistry and the elastic behavior under isothermal conditions up to 9 GPa of a natural, and extremely rare, 3T-phlogopite from Traversella (Valchiusella, Turin, Western Alps) [(K_0.99Na_0.05Ba_0.01)(Mg_2.60Al_0.20Fe _0.21 ²⁺ )[Si_2.71Al_1.29O₁₀](OH)₂, space group P3₁12, with a = 5.3167(4), c = 30.440(2) Å, and V = 745.16(9) ų] have been investigated by electron microprobe analysis in wavelength dispersion mode, single-crystal X-ray diffraction at 100 K, and in situ high-pressure synchrotron radiation powder diffraction (at room temperature) with a diamond anvil cell. The single-crystal refinement confirms the general structure features expected for trioctahedral micas, with the inter-layer site partially occupied by potassium and sodium, iron almost homogeneously distributed over the three independent octahedral sites, and the average bond distances of the two unique tetrahedra suggesting a disordered Si/Al-distribution (i.e., 〈T1-O〉 ~ 1.658 and 〈T2-O〉 ~ 1.656 Å). The location of the H-site confirms the orientation of the O–H vector nearly perpendicular to (0001). The refinement converged with R ₁(F) = 0.0382, 846 unique reflections with F _O > 4σ(F _O) and 61 refined parameters, and not significant residuals in the final difference-Fourier map of the electron density (+0.77/?0.37 e ^?/ų). The high-pressure experiments showed no phase transition within the pressure range investigated. The P–V data were fitted with a Murnaghan (M-EoS) and a third-order Birch-Murnaghan equation of state (BM-EoS), yielding: (1) M-EoS, V ₀ = 747.0(3) ų, K _T0 = 44.5(24) GPa, and K′ = 8.0(9); (2) BM-EoS, V ₀ = 747.0(3) ų, K _T0 = 42.8(29) GPa, and K′ = 9.9(17). A comparison between the elastic behavior in response to pressure observed in 1M- and 3T-phlogopite is made.     

<Emphasis Type="Italic">P</Emphasis>–<Emphasis Type="Italic">V</Emphasis>–<Emphasis Type="Italic">T</Emphasis> equation of state of CaAl<Subscript>4</Subscript>Si<Subscript>2</Subscript>O<Subscript>11</Subscript> CAS phase

The thermoelastic parameters of the CAS phase (CaAl₄Si₂O₁₁) were examined by in situ high-pressure (up to 23.7 GPa) and high-temperature (up to 2,100 K) synchrotron X-ray diffraction, using a Kawai-type multi-anvil press. P–V data at room temperature fitted to a third-order Birch–Murnaghan equation of state (BM EOS) yielded: V _0,300 = 324.2 ± 0.2 Å³ and K _0,300 = 164 ± 6 GPa for K′ _0,300 = 6.2 ± 0.8. With K′ _0,300 fixed to 4.0, we obtained: V _0,300 = 324.0 ± 0.1 Å³ and K _0,300 = 180 ± 1 GPa. Fitting our P–V–T data with a modified high-temperature BM EOS, we obtained: V _0,300 = 324.2 ± 0.1 Å³, K _0,300 = 171 ± 5 GPa, K′ _0,300 = 5.1 ± 0.6 (?K _0,T /?T) _P  = ?0.023 ± 0.006 GPa K^?1, and α_0,T  = 3.09 ± 0.25 × 10^?5 K^?1. Using the equation of state parameters of the CAS phase determined in the present study, we calculated a density profile of a hypothetical continental crust that would contain ~10 vol% of CaAl₄Si₂O₁₁. Because of the higher density compared with the coexisting minerals, the CAS phase is expected to be a plunging agent for continental crust subducted in the transition zone. On the other hand, because of the lower density compared with lower mantle minerals, the CAS phase is expected to remain buoyant in the lowermost part of the transition zone.