大断面小净距隧道围岩稳定性数值分析 大断面小净距隧道围岩稳定性数值分析

结合小净距隧道工程特点,分别建立不同跨度小净距隧道有限元计算模型,对隧道施工过程力学特征及围岩稳定性进行对比分析,以研究三车道大断面小净距隧道区别于两车道小净距隧道的基本力学特征。分析结果表明,对应不同隧道跨度、隧道净距和围岩级别对隧道施工过程中围岩稳定性的影响有显著差别,相同隧道净距条件下,三车道小净距隧道围岩应力状态比两车道隧道差,净距越小,差别越大,而围岩质量越低,差别也越显著;另外,在质量较差的围岩中,大断面小净距隧道围岩受力最薄弱部位主要集中在岩柱雁形部,而两车道小净距隧道则为岩柱中部。研究结果可为大断面小净距隧道的设计、施工提供有益的参考。     

大断面小净距隧道围岩稳定性数值分析

结合小净距隧道工程特点,分别建立不同跨度小净距隧道有限元计算模型,对隧道施工过程力学特征及围岩稳定性进行对比分析,以研究三车道大断面小净距隧道区别于两车道小净距隧道的基本力学特征。分析结果表明,对应不同隧道跨度、隧道净距和围岩级别对隧道施工过程中围岩稳定性的影响有显著差别,相同隧道净距条件下,三车道小净距隧道围岩应力状态比两车道隧道差,净距越小,差别越大,而围岩质量越低,差别也越显著;另外,在质量较差的围岩中,大断面小净距隧道围岩受力最薄弱部位主要集中在岩柱雁形部,而两车道小净距隧道则为岩柱中部。研究结果可为大断面小净距隧道的设计、施工提供有益的参考。     

厦门机场路隧道双连拱与小间距工法设计比选

小间距隧道是双洞隧道净距介于连拱隧道与规范要求上下行分离式隧道最小净距之间的一种特殊隧道结构形式。文章以厦门机场路高速公路隧道为依托,对隧道双连拱、小间距工法进行了施工过程的动态数值模拟。以地表沉降作为主要控制目标,对不同的施工方案进行了优化分析,得出采用小间距断面的方案优于双连拱方案,数值模拟过程中地下结构和周围环境没有安全隐患。这为工程的顺利实施提供了依据和指导,可供类似工程参考。     

桩基础荷载对邻近已有隧道影响的有限元分析

目前,城市密集的高层建筑桩基础对临近隧道的影响问题越来越突出,为了更好地理解桩群荷载对已建成隧道的影响,主要进行了两方面的研究：（1）利用平面应变有限元方法分析了桩列荷载作用对邻近已有隧道的变形及受力影响,并研究了桩群参数变化（包括桩间距以及桩基础与隧道结构净距）对现存隧道的影响;（2）分析计算了上海太平洋2期广场工程对邻近地铁1号线隧道的影响。分析结果表明：隧道单侧存在桩列荷载作用时,隧道变形以沉降为主,水平位移较小,同时隧道结构向桩基础方向产生一定扭曲,这对于运营地铁是十分不利的;桩基础荷载造成隧道所受弯矩分布向桩基础方向偏转;随着桩间距、桩与隧道净距的增加,隧道拱顶下沉量以及弯矩变化最大值相应减小,沿隧道方向桩间距变化影响大于垂直隧道方向桩间距变化影响。     

鹤上大断面小净距隧道施工方案优化分析

结合福州国际机场高速公路鹤上大断面小净距隧道工程实际,建立了大断面小净距隧道施工动态有限元分析程序,对隧道施工方案的优化进行了数值模拟分析。分析中模拟了双侧壁导坑法、中隔壁法和上下台阶法3种施工方案,对拱顶下沉、地表沉降、中间岩柱应力、围岩稳定性等进行了对比分析,并结合鹤上隧道围岩实际情况,在隧道出口Ⅴ级围岩段,改双侧壁导坑法为中隔壁法,顺利完成了施工,对降低施工成本、加快施工进度均起到了较好的作用,研究结果可为类似条件下大断面小净距隧道的设计、施工提供借鉴与参考。     

基于强度折减法小净距隧道合理净距的研究

小净距隧道合理净距的确定是目前研究的热点和难点.影响小净距隧道合理净距的因素很多,解析法虽然可以得到精确解,但是公式烦琐,而数值计算方法可以计算各种情况下围岩的应力、变形、塑性区分布等情况.小净距隧道合理净距的确定也即是隧道稳定性发生突变时两独立隧道最小距离的确定.提出了合理净距确定的原则,并采用强度折减弹塑性有限元方法,针对某工程实例,计算了在不同净距情况下隧道的安全系数,并把安全系数发生突变时的净距作为合理净距,和传统有限元分析的结果相吻合.     

小净距公路隧道稳定性数值模拟分析

常(德)-吉(首)高速公路上的阿娜隧道是因隧道净距小,双洞间影响较大,故应用二维弹塑性有限元分析方法对其稳定性进行分析研究,计算了衬砌和围岩的内力与位移,进行了变形性状的分析,为高速公路类似的小净距隧道工程设计、施工提供一定的科学依据和参考价值。     

扁平大跨度公路隧道松动荷载计算方法探讨

确定松动荷载的方法多为规范法和理论公式法,这些方法都建立在对以往隧道松动荷载统计和分析的基础上。双洞八车道扁平大跨度公路隧道是近几年发展起来的一种隧道形式。由于其跨度增加、扁平率降低,现有松动荷载的算方法是否适用于双洞八车道公路隧道,已成为隧道建设者面对的重要问题之一。以广州龙头山双洞八车道公路隧道为研究背景,概括和总结了各种松动荷载的计算方法;应用这些方法计算龙头山隧道的松动压力,分析和对比计算结果,并通过数值计算和实测围岩压力对各种方法的合理性进行了分析;根据各种方法的产生背景和内容,分析其各自的适用性;根据研究结果,对扁平大跨度公路隧道进行了适应性分析和讨论。     

特大跨度小净距隧道中间岩柱可靠度分析及其加固处理措施

魁岐2号隧道位于福卅I国际机场高速公路二期工程A3标段,隧道跨度达到19．9m,中间岩柱最小净距为11．7m,为国内首座双向八车道小净距隧道工程。针对魁岐2号隧道工程的特殊性,利用离散单元法对节理岩体中特大断面小净距隧道的受力情况进行了分析,根据可靠度理论,通过对魁岐2号特大断面小净距隧道中间岩柱的可靠性分析发现,对于特大断面小净距隧道,中间岩柱最薄弱的部位主要集中在岩柱上部,因此,埘于特大断面小净距隧道施工过程中宜重点对岩柱上部进行加固处理。同时,根据不同围岩级别中中间岩柱的可靠度值显示,魁岐2号特大断面小净距隧道的净距取值基本上是合理的,整体上二能满足稳定性的要求。     

煤系地层大跨度隧道围岩结构稳定性研究

针对目前大跨穿煤隧道的研究热点,以重庆市绕城高速公路环山坪隧道为研究对象,在界定大跨度隧道及分析其围岩稳定性关键影响因素的基础上,结合现场监测和数值模拟对大跨度穿煤隧道围岩结构稳定性进行了分析。结果表明,大跨度隧道各处等效应力集中对扁平率变化敏感程度不同,拱脚最为敏感,拱顶基本不随扁平率的改变而变化。隧道穿越软弱煤层段时,围岩应力重分布受影响明显,拱顶位移随开挖面不断推进急剧增加,且隧道围岩塑形圈不断向拱顶围岩内部发展。尤其当煤层软弱带与隧道顺层相交时,隧道荷载结构偏压效应凸显,偏压荷载随煤层倾角变陡而增大,易造成支护结构失稳破坏,在设计及施工中应特别加以重视。     

不同围岩类别小间距隧道施工过程模拟研究

从不同围岩类别出发,对3车道小间距隧道采用典型双侧导坑法的开挖施工过程进行了数值模拟研究。给出了不同围岩类型下的3车道小间距隧道在施工过程中的围岩破坏特征及其变形规律和变形规律的相似性,获得了洞周最大变形量值之间的相对比值关系。通过中隔墙的变形与塑性破坏规律分析,比选出了3车道隧道中隔墙最小间距的工程设计参考值。分析表明：II类围岩合理间距不应小于0.45B,III类围岩应在0.35～0.45B之间,IV,V类围岩可在0.2～0.35B之间选择,对信息化反馈施工,指出了必须重点监控与关注的位置。为小间距隧道的发展和施工设计提供了较确切的参考数据和理论依据。     

An analytical solution for deforming twin‐parallel tunnels in an elastic half plane

The interaction between twin‐parallel tunnels affects the tunnelling‐induced ground deformation, which may endanger the nearby structures. In this paper, an analytical solution is presented for problems in determining displacements and stresses around deforming twin‐parallel tunnels in an elastic half plane, on the basis of complex variable theory. As an example, a uniform radial displacement was assumed as the boundary condition for each of the two tunnels. Special attention was paid to the effects of tunnel depth and spacing between the two tunnels on the surface movement to gain deep insight into the effect of the interaction between twin‐parallel tunnels using the proposed analytical approach. It is revealed that the influence of twin tunnel interaction on surface movements diminishes with both the increase of the tunnel depth and the spacing between the two tunnels. The presented analytical solution manifests that, similar to most of the existing numerical results, the principle of superposition can be applied to determine ground deformation of twin‐parallel tunnels with a certain large depth and spacing; otherwise, the interaction effect between the two tunnels should be taken into account for predicting reliable ground movement. Copyright © 2014 John Wiley & Sons, Ltd.     

平面P波入射下浅埋平行双洞隧道注浆加固减震机制

地震动作用下小净距隧道双洞之间存在动力放大效应,依托某强震区小净距盾构隧道工程,基于傅里叶贝塞尔级数展开法,给出了平面P波垂直入射下地下半空间弹性介质中圆形双洞复合式衬砌洞室动应力解析解,深入研究了洞室间距、隧道全环注浆加固参数对衬砌动应力集中的影响。研究表明：洞室间距对衬砌的动应力有显著影响,随着洞室之间距离减小,左右洞室衬砌动应力明显放大;2.5倍洞径可以作为双洞洞室动力临界净距,当洞室间距小于2.5倍洞径时,应进行抗减震设计;注浆全环加固隧道周边土体,可以明显降低衬砌动应力,随着注浆加固区土体刚度增加,衬砌动应力幅值减小;结合工程实际,建议注浆加固区厚度取0.5倍的洞室半径值,加固区岩体和围岩剪切波速度之比取1.2。     

Improving the existing roadway tunnels capacity by adding new tunnels—a structural approach

The roadway tunnel is considered a good solution for the success of modern roadway networks. It can help to overcome possible traffic congestion and considerably reduce journey time. The continuous growth of traffic volumes leads to increase congestion and decrease safety. This leads to the need for extra tunnel space. The extra tunnel space can be achieved either by the widening of the existing tunnel or by adding a new one. The choice of the suitable method is dependent on many factors like tunnels alignment, site conditions, construction method, tunnel operation, risk assessment…etc. The current research investigates the second alternative through a specific case study as an example. The method comprises adding two new tunnels to an existing twin roadway tunnels. The investigated problem considers the new tunnels to be added vertically or horizontally. The influence of the new tunnel construction on the existing tunnels is investigated considering both the variation of relative position and spacing distance in a parametric study context. Several numerical models are employed to check the construction sequence and the tunnelling safety. These models are used to evaluate the induced stresses in surrounding ground for two different soil types, straining actions in tunnels’ liner and deformations of both ground and liner. The result demonstration shows how to find out the minimum practical and safe spacing distance between the driven new tunnels and the existing ones without the need for the relatively expensive soil strengthening techniques.     

A hybridized numerical and regression method for estimating the minimum rock pillar width of twin circular tunnels

Twin tunnels can be used for many applications. Interaction between two tunnels is an important problem in tunnel engineering that should be studied specially. Numerical investigations are well adapted to field data and numerical methods can be used in design of rock pillar of twin circular tunnels. So far, no relationship has been provided to estimate the minimum stable rock pillar width. In this paper, the interaction between twin circular tunnels has been studied using 2D finite element analysis. To do this, a great number of twin tunnels were modeled in Phase2 software with different conditions of rock mass (RMR value) and depth of tunnel. Models were analyzed and minimum stable rock pillar width was determined. This process was repeated for three different ratios of K (ratio of horizontal stress to vertical stress, 0.5, 1, and 1.5). Finally, according to the linear and nonlinear regression methods, the best merit function was fitted to result of numerical analysis. Then, new approximate formula was proposed to estimate the minimum rock pillar width according to RMR value and depth of twin circular tunnels with different K values. The formulae are very accurate (coefficient of correlation equals to minimum 0.96) that can be used for estimating the minimum rock pillar width of twin circular tunnels.     

大断面小净距大帽山隧道现场监控量测及分析

结合大帽山隧道的工程实践,通过围岩内部位移、拱顶沉降、围岩压力和锚杆应力的现场监控量测工作,研究复杂地质条件下大断面小净距隧道双侧壁导坑法施工时围岩的稳定性。阐明分导洞开挖时围岩内部位移的变化趋势、特点及位移场,相邻导洞施工时的相互影响,围岩与支护结构间的相互调整变形机制,拱顶沉降捕捉的变形小于围岩实际变形的原因,支护结构的压力和锚杆应力状态及其与围岩位移的变化关系。监测结果表明,大断面小净距隧道Ⅴ级围岩段的破碎带采用现有的施工工艺和支护参数是可行的,围岩变形可控,支护结构的支护效果显著,围岩基本稳定。研究的方法、分析和结论可为类似条件下隧道工程的设计、施工、监测和进一步的理论研究提供参考和借鉴。     

Performance of a multi-face tunnel excavated in loess ground based on field monitoring and numerical modeling

In large-span tunneling projects, the mechanical behavior of the rock changes in response to different sequential excavation methods (SEMs) of advancing the tunnel face. The double side drift method (DSDM), which is a development of SEM, was widely used in loess tunnels with large cross sections in China for its ability to limit ground displacement. This paper presents the deformation characteristics of large-span loess tunnels of the high-speed railway line in China. Field monitoring and numerical simulations were conducted to determine the optimal construction approach and reveal the deformation properties of large-span loess tunnels in China. The construction approaches, support measures, ground surface, and subsurface deformation characteristics associated with DSDM are demonstrated. The ground surrounding the loess tunnel underwent vertical settlement at the arch part and at the ground surface because of the metastable structure of the loess. This study provides an in-depth illustration of the influence of face-advancing sequences on ground displacement induced by tunneling, which helps us implement the most effective SEMs.     

深埋小净距多线平行盾构掘进相互作用分析

浅覆软弱地层中小净距盾构隧道施工时,后行隧道施工显著影响先行隧道安全,但深埋情况下,由于地下岩土层的复杂性和不确定性,使得多线隧道施工时先行隧道的变形变得复杂。以上海硬X射线土建部分盾构隧道为背景,结合有限元数值模拟,分析了深埋小净距盾构隧道施工时的相互影响,并对不同的盾构参数进行了敏感性分析。研究表明:随着后行隧道的开挖,先行隧道管片的变形增量变化基本呈双峰特征。当采用左-右-中方式开挖时,管片变形增量呈一大一小双峰分布;而采用中-右-左方式时,管片竖向变形增量峰值的大小和方向相同,而水平变形增量的峰值相同,方向不同;随着浆液弹性模量的增加,管片竖向变形增量变化较大,水平变形增量基本不变;随着顶推力的增大,管片的变形也在相应地增大,并在支护应力比为0.6～0.7之间时达到稳定;地下水的存在对管片竖向变形有着一定的影响;通过对比2种开挖方式管片的变形收敛情况,选择左-右-中次序开挖比较安全。