巷道围岩稳定性的判据及岩石分类

本文通过套筒致裂法测试巷道围岩应力及力学性质,并以此进行围岩稳定性分析和分类;提出了巷道围岩稳定性判据以及巷道围岩分类的原则;介绍了本稳定性分析方法在若干煤矿巷道围岩及立井井壁应力测试地点的应用。     

节理岩体中隧道开挖与支护的数值模拟

由于节理、断层等不连续面的存在造成岩体变形的不连续性,并且这些不连续面对岩体变形、应力等力学行为造成重要影响。对已有的非连续变形分析程序进行了两点改进,应用改进的程序模拟了节理岩体中隧洞开挖与支护的过程,研究了不同节理倾角岩体的应力分布特性、开挖后隧洞围岩的变形和应力分布规律以及支护后衬砌的变形与应力特点。研究结果表明,节理倾角对节理岩体系统的应力和变形有着直接的影响,并且影响着隧洞开挖后的内空收敛效应;隧洞开挖顺序对围岩的变形和稳定也有重要影响。改进后的非连续变形分析方法和程序可以用来分析复杂节理岩体系统中隧洞的开挖与支护。     

Supported Axisymmetric Tunnels Within Linear Viscoelastic Burgers Rocks

An exact closed form solution is derived for the mechanical behaviour of a linear viscoelastic Burgers rock around an axisymmetric tunnel, supported by a linear elastic ring. Analytical formulae are provided for the displacement of the rock/lining interface and for the pressure exerted by the rock on the lining, taking into account the stiffness and its installation time. Results calculated from these formulae do validate the corresponding numerical results of a 2D finite differences code. Further, comparison to previous existing solutions for the same viscoelastic model indicates similarities and differences. A parametric study is performed to investigate the effect of the viscoelastic constants, the stiffness and installation time of the support. The derived closed form solution is used to construct the time-dependent Supported Ground Reaction Curves of the viscoelastic rock, i.e. the time contour plots on the convergence confinement diagram. The importance of the effect of the support on the restrained rock creep and the exerted pressure on the lining, during the design life of a structure, is examined.     

复合式衬砌结构中衬砌分担围岩压力比例的研究

复合式衬砌结构中衬砌分担围岩压力的评价方法是隧道工程技术的重要研究课题之一。依托某新建铁路隧道工程,提出了一种基于监测位移反分析评价围岩和支护应力,进而计算初期支护和衬砌背后压力的方法。根据监测位移和衬砌施作时间,确定初期支护的已发生变形和剩余变形。通过有限元反分析求出与已发生变形和剩余变形相对应的围岩和支护应力,得到初期支护和衬砌背后压力。对比初期支护背后压力及衬砌背后压力的现场监测和反分析的计算结果,两者比较一致,说明了该方法的可行性。该新建隧道初期支护闭合95 d后施作衬砌,计算得到衬砌背后压力约0.04～0.06 MPa,衬砌分担围岩压力比例约13%～16%。研究成果对复合式衬砌结构的设计具有一定的参考意义。     

The effect of inertia,viscous damping,temperature and normal stress on chaotic behaviour of the rate and state friction model

A fundamental understanding of frictional sliding at rock surfaces is of practical importance for nucleation and propagation of earthquakes and rock slope stability. We investigate numerically the effect of different physical parameters such as inertia, viscous damping, temperature and normal stress on the chaotic behaviour of the two state variables rate and state friction (2sRSF) model. In general, a slight variation in any of inertia, viscous damping, temperature and effective normal stress reduces the chaotic behaviour of the sliding system. However, the present study has shown the appearance of chaos for the specific values of normal stress before it disappears again as the normal stress varies further. It is also observed that magnitude of system stiffness at which chaotic motion occurs, is less than the corresponding value of critical stiffness determined by using the linear stability analysis. These results explain the practical observation why chaotic nucleation of an earthquake is a rare phenomenon as reported in literature.     

岩质隧洞支护结构设计计算方法探索

依靠模型试验与力学计算,分析了隧洞破坏机制与型式,提出将基于有限元强度折减法求出的围岩安全系数作为稳定分析判据。现有各种围岩分类中都有一些标志围岩稳定性的标志性说明,在前人基础上,提出了各级岩体的稳定性标志,尤其提出了一种新的定量标志,即将隧洞在无衬砌情况下的围岩安全系数作为隧洞稳定性定量标志。由此,在给出的相应稳定安全系数基础上反算出各级岩体的强度参数,以提高强度参数的准确性。提出了岩质隧洞的设计计算方法,采用有限元强度折减法计算围岩安全系数,采用有限元法计算衬砌安全系数,并对青岛市某地下工程进行数值模拟,分别计算了围岩和衬砌的安全系数。初步建议岩体隧洞的设计标准：初期支护后,围岩安全系数不小于1.15～1.2,初衬的安全系数不小于1.3;二次支护后围岩安全系数高于1.25,衬砌的安全系数大于2.0～2.4,以确保隧洞在施工和运行过程中的安全。     

Analysis of the evolution of road tunnels equilibrium conditions with a convergence–confinement approach

Since both lining structure and rock mass exhibit delayed behaviour, tunnel equilibrium conditions evolve with time. After discussing existing work done on different aspects of long-term tunnel behaviour, the aim of this paper is to “understand” the influence of rock mass and lining degradations on the long-term stability conditions of the tunnel by means of the convergence–confinement method. In order to represent the effects of degradation on tunnel long-term conditions, specific degradation models are selected according to the disorders identified during principal inspections of road tunnels in Switzerland. By simulating the reduction of the mechanical properties of both the rock mass and the lining or by using creep models, it is possible to assess the influence of the main degradation processes on tunnel stability. The results are interpreted in terms of tunnel safety factor. The presented approach for the determination of the long-term behaviour of tunnels, although valid for simple tunnel geometry and field stress conditions, allows to roughly estimate the influence of significant degradation processes that affect the rock mass and the supporting structure. Though this approach results in some simplification, it may be generalised and adopted with more refined numerical analyses for improving the assessment of tunnel long-term conditions.     

京承高速公路新道沟连拱隧道的优化设计

本文以京承高速公路新道沟连拱隧道为实例,应用有限元数值方法对连拱隧道二次衬砌的围岩抗力、应力、变形及其稳定性等问题进行了模拟与分析。首先,基于连拱衬砌的结构型式,作者建立了该隧道的数值模型,并提出用弹性杆单元按作用力等效的原则模拟围岩抗力;根据数值模拟结果对隧道支护结构的承载能力进行了讨论,并基于规范对二次衬砌进行了结构强度校核。该研究结果为新道沟隧道支护结构设计的优化提供了科学依据。     

Q2饱和黄土隧洞围岩变形特征研究

Q₂饱和黄土含水率高,强度低、变形大。饱和黄土隧洞围岩变形破坏一直是工程界关心和亟待解决的问题。利用隧洞围岩收敛变形、二次应力场监控量测与数值分析,获取隧洞围岩动态综合信息,研究在一次支护条件下,隧洞围岩的收敛变形和应力变化特征。结果显示,隧洞围岩收敛变形和应力在最初的10~15天呈线性快速增长趋势。后期,收敛变形随时间呈非线性增加,受一次衬砌的限制,其变形在隧洞开挖30~40天后渐趋于稳定,但应力持续增加,反映Q₂饱和黄土隧洞围岩具有显著的时效特性。为避免隧洞围岩压力过大,造成隧洞围岩及支护破坏,建议在开挖后30~40天施作二次衬砌。     

隧道开挖与支护有限差分法分析

根据景德镇-黄山高速公路某隧道现场工程地质条件和隧道结构设计参数,采用有限差分法对喷射500 mm普通混凝土支护和喷射200 mm厚聚丙烯纤维混凝土支护两种支护结构,进行了施工过程的数值模拟分析。从围岩的应力、位移和塑性区分布3个方面对隧道围岩的稳定性进行了分析。模拟计算结果表明,采用喷射200 mm厚聚丙烯纤维混凝土支护结构的隧道围岩能够处于稳定状态。     

软弱围岩隧道施工全过程非线性有限元分析

结合赣州-龙岩铁路某单线隧道软弱围岩地质情况,采用非线性有限元法对软弱围岩条件下的铁路隧道湿喷纤维混凝土支护结构施工过程进行了数值模拟,分析了围岩和支护结构体的非线性力学行为的应力场分布、位移场,围岩塑性区分布特征,指出台阶步开挖时拱顶下沉、底板上鼓、墙腰收缩的主要控制因素.     

东巨寺沟隧道湿喷纤维混凝土支护结构和围岩稳定性位移模糊判别

湿法喷射混凝土可有效地改善隧道内作业环境、反弹量小、喷射质量高,是隧道支护结构施工值得推广的工艺。首次在宝鸡－兰州铁路复线东巨寺沟铁路隧道选取试验段,实施湿喷工艺喷射聚丙烯纤维混凝土,作为支护结构兼作永久性支护,免除二次衬砌工作,并进行水平位移收敛监测。采用非线性最小二乘法对该隧道水平收敛曲线进行回归分析,同时采用隧道稳定性模糊概率分析理论对不同断面位置处的隧道围岩稳定性进行判别分析。分析结果表明,采用湿喷纤维混凝土支护的隧道围岩处于稳定状态,可靠度指标高。     

Micro- and macro-behaviour of fluid flow through rock fractures: an experimental study

Microscopic and macroscopic behaviour of fluid flow through rough-walled rock fractures was experimentally investigated. Advanced microfluidic technology was introduced to examine the microscopic viscous and inertial effects of water flow through rock fractures in the vicinity of voids under different flow velocities, while the macroscopic behaviour of fracture flow was investigated by carrying out triaxial flow tests through fractured sandstone under confining stresses ranging from 0.5 to 3.0 MPa. The flow tests show that the microscopic inertial forces increase with the flow velocity with significant effects on the local flow pattern near the voids. With the increase in flow velocity, the deviation of the flow trajectories is reduced but small eddies appear inside the cavities. The results of the macroscopic flow tests show that the linear Darcy flow occurs for mated rock fractures due to small aperture, while a nonlinear deviation of the flow occurs at relatively high Reynolds numbers in non-mated rock fracture (Re?>?32). The microscopic experiments suggest that the pressure loss consumed by the eddies inside cavities could contribute to the nonlinear fluid flow behaviour through rock joints. It is found that such nonlinear flow behaviour is best matched with the quadratic-termed Forchheimer equation.     

Analysis of the Dynamic Performance of an Underground Excavation in Jointed Rock under Repeated Seismic Loading

Results from field observations of dynamic behaviour of an underground excavation have been compared with numerical studies of the rock deformation history. The field behaviour shows progressive accumulation of rock displacement and excavation deformation under successive episodes of dynamic loading. It is possible to reproduce the modes of rock response quite well using a Distinct Element model of the rock mass, but the way displacements develop is dependent on the joint model used in the analysis. It is suggested that, in rock masses subject to repeated dynamic loading, excavation design may need to take account of the prospect of repeated episodes of transient loading at the excavation site.     

Some recent advances in the modelling of soft rock joints in direct shear

This paper presents a review of recent developments made by the authors into the modelling of rock joints in direct shear. Careful observation of laboratory direct shear testing on concrete/rock joints containing two-dimensional roughness has allowed theoretical models of behaviour to be developed. The processes modelled include asperity sliding, asperity shearing, post-peak behaviour, asperity deformation and distribution of stresses on the joint interface. Model predictions compare extremely well with laboratory test results. These models were then applied to direct shear tests on rock/rock joints, and although behaviour in general was well predicted, the strength of rock/rock joints was over-predicted. Direct shear tests have also been carried out on samples containing both two- and three-dimensional roughness to test the accuracy of the two-dimensional approximation to roughness adopted in the theoretical models.     

Influence of Rock Mass Parameters on the Performance of a TBM in a Gneissic Formation (Varzo Tunnel)

Summary The paper analyses the influence of rock mass quality on the performance of a double shield TBM in the excavation of a tunnel in a gneiss formation which is characterized by high strength and low fracture intensity.As full observation of the rock conditions was prevented by the use of segmental lining, a geomechanical survey of the face was performed during maintenance downtime and the observed conditions were correlated with the machine performance parameters for that same day. A statistical analysis of the data shows that penetration rate correlates well with a slightly modified RMR index (in which the influence of the water conditions and joint orientation were discounted), but the most important factor is by far the partial rating of the RMR classification related to joint spacing only. However in tunnels characterized by greater variability in rock strength and joint conditions, it could be worthwhile using the complete RMR index.Given the toughness of the rock, failure of the cutter bearings and supports were a frequent occurrence during excavation. Owing to this factor the influence of rock quality on the rate of advance was found to be weak and the correlation more scattered.The results obtained for the Varzo tunnel were compared with those relative to other tunnels in granitic rocks and found to be in good agreement. However the relationships obtained should be considered valid only for this type of rock; machine behaviour could be found to be markedly different in other rock types, even where rock material strength and joint frequency are the same.     

初期支护对软岩隧道围岩稳定性和位移影响分析

软弱岩体隧道开挖后,围岩变形具有异常显著的流变性。基于Poyting-Thomoson模型,对隧道围岩位移进行了粘弹性解析分析,根据所得出的解析解,结合渝（重庆）沙（长沙）高速公路石龙隧道位移监控量测实践,对初期支护后隧道围岩变形特征量进行了分析对比,结果表明,理论曲线能较好地反映围岩实际位移变化特征。最后通过将支护前后围岩受力状态与单轴和三轴应力状态岩石蠕变进行类比,得知初期支护在一定程度上减小了围岩的最终变形量,可以有效地抑制隧道围岩的变形速率。其结果为确定合理的二次支护时机提供了理论依据,对同类隧道的施工支护具有很好的指导意义和较高的参考价值。     

正交各向异性岩体中非圆形水工隧洞的解析解

将围岩和衬砌分别视作均质、连续的线弹性正交各向异性和各向同性体,并充分考虑衬砌的支护滞后效应和隧洞运行时的内水压力作用,运用复变函数方法中的幂级数解法,提出了正交各向异性岩体中任意形状水工隧洞的力学解析方法。以直墙半圆拱形水工隧洞为例,所获得的解析解可精确满足衬砌内边界的应力边界条件以及围岩与衬砌接触面的应力、位移连续条件,同时还将解析结果与ANSYS数值结果对比分析,吻合良好。利用获得的解析解,讨论了围岩开挖面上不同的各向异性程度、不同的弹性对称面角度以及隧洞内不同的水压荷载对衬砌以及围岩上应力和位移分布的影响。     

浅埋双连拱隧道围岩边坡体系变形机理及稳定性分析

双连拱隧道是一种新的隧道形式, 由于其整体跨度大、结构复杂、施工工序繁琐, 在地形偏压、地质条件复杂的情况下修建双连拱隧道难度较高, 尤其在洞口段容易出现衬砌开裂、边坡变形等一系列工程问题。结合安徽铜黄高速公路汤屯段富溪隧道进口段工程, 采用地质条件研究与数值模拟分析相结合的研究手段, 对复杂地质条件下偏压双连拱隧道围岩① 边坡体系在施工过程中应力应变发展过程进行了研究。综合分析表明, 富溪隧道进口段处于F5断层影响带内, 岩体呈碎裂结构,同时, 受到地形偏压影响, 隧道开挖后衬砌和围岩表现为沉降变形和侧向变形, 进口边坡在隧道围岩变形的诱导下, 表现为蠕滑- 拉裂变形破裂。根据以上研究成果, 提出了富溪隧道变形治理应以控制进口段隧道拱顶的变形为主。