High-pressure phase transitions of CaRhO<Subscript>3</Subscript> perovskite

High-pressure phase transitions of CaRhO₃ perovskite were examined at pressures of 6–27 GPa and temperatures of 1,000–1,930°C, using a multi-anvil apparatus. The results indicate that CaRhO₃ perovskite successively transforms to two new high-pressure phases with increasing pressure. Rietveld analysis of powder X-ray diffraction data indicated that, in the two new phases, the phase stable at higher pressure possesses the CaIrO₃-type post-perovskite structure (space group Cmcm) with lattice parameters: a = 3.1013(1) Å, b = 9.8555(2) Å, c = 7.2643(1) Å, V _m  = 33.43(1) cm³/mol. The Rietveld analysis also indicated that CaRhO₃ perovskite has the GdFeO₃-type structure (space group Pnma) with lattice parameters: a = 5.5631(1) Å, b = 7.6308(1) Å, c = 5.3267(1) Å, V _m  = 34.04(1) cm³/mol. The third phase stable in the intermediate P, T conditions between perovskite and post-perovskite has monoclinic symmetry with the cell parameters: a = 12.490(3) Å, b = 3.1233(3) Å, c = 8.8630(7) Å, β = 103.96(1)°, V _m  = 33.66(1) cm³/mol (Z = 6). Molar volume changes from perovskite to the intermediate phase and from the intermediate phase to post-perovskite are –1.1 and –0.7%, respectively. The equilibrium phase relations determined indicate that the boundary slopes are large positive values: 29 ± 2 MPa/K for the perovskite—intermediate phase transition and 62 ± 6 MPa/K for the intermediate phase—post-perovskite transition. The structural features of the CaRhO₃ intermediate phase suggest that the phase has edge-sharing RhO₆ octahedra and may have an intermediate structure between perovskite and post-perovskite.     

Argon retention properties of silicate glasses and implications for <Superscript>40</Superscript>Ar/<Superscript>39</Superscript>Ar age and noble gas diffusion studies

Sized aggregates of glasses (47–84 wt% SiO₂) were fused from igneous-derived cohesive fault rock and igneous rock, and step-heated from ~400 to >1,200 °C to obtain their ³⁹Ar diffusion properties (average E=33,400 cal mol^?1; D _o=4.63×10^?3 cm² s^?1). At T<~1,000 °C, glasses containing <~69 wt% SiO₂ and abundant network-forming cations (Ca, Fe, Mg) reveal moderate to strong non-linear increases in D and E, reflecting structural modifications as the solid transitions to melt. Extrapolation of these Arrhenius properties down to typical geologic T-t conditions could result in a 1.5 log₁₀ unit underestimation in the diffusion rate of Ar in similar materials. Numerical simulations based upon the diffusion results caution that some common geologic glasses will likely yield ⁴⁰Ar/³⁹Ar cooling ages rather than formation ages. However, if cooling rates are sufficiently high, ambient temperatures are sufficiently low (e.g., <65–175 °C), and coarse particles (e.g., radius (r) >~1 mm) are analyzed, glasses with compositions similar to ours may preserve their formation ages.     

High-pressure synthesis,long-term stability of single crystals of diboron trioxide,B<Subscript>2</Subscript>O<Subscript>3</Subscript>, and an empirical electronic polarizability of <Superscript>[3]</Superscript>B<Superscript>3+</Superscript>

Single crystals of B₂O₃ are needed for the precise determination of the refractive indices used to calculate the electronic polarizability α of 3-coordinated boron. The α(B) values in turn are used to predict mean refractive indices of borate minerals. Since the contribution of boron to the total polarizability of a mineral is very low, the synthetic compound B₂O₃ represents an ideal model system because of its high molar content of boron. Millimeter-sized crystals were synthesized at 1 GPa in a piston-cylinder apparatus. The samples were heated above the liquidus (800 °C), subsequently cooled at 15 °C/h to 500 °C and finally quenched. The refractive indices were determined by the immersion method using a microrefractometer spindle stage. The refractive indices n _o = 1.653 (3) and n _e = 1.632 (3) correspond to a total polarizability for B₂O₃ of α = 4.877 Å³. These values were used to determine the electronic polarizability of boron of α(B) = 0.16 Å³. Although the surface of the B₂O₃ crystals was coated with a hydrous film immediately after being exposed to air, its bulk crystallinity is retained for a period of at least 2 months.     

Synthesis,TEM characterization and thermal behaviour of LiNiSi<Subscript>2</Subscript>O<Subscript>6</Subscript> pyroxene

A pyroxene with composition LiNiSi₂O₆ was synthesized at T = 1,473 K and P = 2.0 GPa; the cell parameters at T = 298 K are a = 9.4169(6) Å, b = 8.4465(7) Å, c = 5.2464(3) Å, β = 110.534(6)°, V = 390.78(3) Å³. TEM examination of the LiNiSi₂O₆ pyroxene showed the presence of h + k odd reflections indicative of a primitive lattice, and of antiphase domains obtained by dark field imaging of the h + k odd reflections. A HT in situ investigation was performed by examining TEM selected area diffraction patterns collected at high temperature and synchrotron radiation powder diffraction. In HTTEM the LiNiSi₂O₆ was examined together with LiCrSi₂O₆ pyroxene. In LiCrSi₂O₆ the h + k odd critical reflections disappear at about 340 K; they are sharp up to the transition temperature and do not change their shape until they disappear. In LiNiSi₂O₆ the h + k odd reflections are present up to sample deterioration at 650 K. A high temperature synchrotron radiation powder diffraction investigation was performed on LiNiSi₂O₆ between 298 and 773 K. The analysis of critical reflections and of changes in cell parameters shows that the space group is P-centred up to the highest temperature. The comparative analysis of the thermal and spontaneous strain contributions in P2₁/c and C2/c pyroxenes indicates that the high temperature strain in P-LiNiSi₂O₆ is very similar to that due to thermal strain only in C2/c spodumene and that a spontaneous strain contribution related to pre-transition features is not apparent in LiNiSi₂O₆. A different high-temperature behaviour in LiNiSi₂O₆ with respect to other pyroxenes is suggested, possibly in relation with the presence of Jahn–Teller distortion of the M1 polyhedron centred by low-spin Ni³⁺.     

Stability at high-pressure,elastic behaviour and pressure-induced structural evolution of CsAlSi<Subscript>5</Subscript>O<Subscript>12</Subscript>, a potential host for nuclear waste

The elastic and structural behaviour of the synthetic zeolite CsAlSi₅O₁₂ (a = 16.753(4), b = 13.797(3) and c = 5.0235(17) Å, space group Ama2, Z = 2) were investigated up to 8.5 GPa by in situ single-crystal X-ray diffraction with a diamond anvil cell under hydrostatic conditions. No phase-transition occurs within the P-range investigated. Fitting the volume data with a third-order Birch–Murnaghan equation-of-state gives: V ₀ = 1,155(4) ų, K _T0 = 20(1) GPa and K′ = 6.5(7). The “axial moduli” were calculated with a third-order “linearized” BM-EoS, substituting the cube of the individual lattice parameter (a ³, b ³, c ³) for the volume. The refined axial-EoS parameters are: a ₀ = 16.701(44) Å, K _T0a = 14(2) GPa (β_a = 0.024(3) GPa^?1), K′ _a = 6.2(8) for the a-axis; b ₀ = 13.778(20) Å, K _T0b = 21(3) GPa (β_b = 0.016(2) GPa^?1), K′ _b = 10(2) for the b-axis; c ₀ = 5.018(7) Å, K _T0c = 33(3) GPa (β_c = 0.010(1) GPa^?1), K′ _c = 3.2(8) for the c-axis (K _T0a:K _T0b:K _T0c = 1:1.50:2.36). The HP-crystal structure evolution was studied on the basis of several structural refinements at different pressures: 0.0001 GPa (with crystal in DAC without any pressure medium), 1.58(3), 1.75(4), 1.94(6), 3.25(4), 4.69(5), 7.36(6), 8.45(5) and 0.0001 GPa (after decompression). The main deformation mechanisms at high-pressure are basically driven by tetrahedral tilting, the tetrahedra behaving as rigid-units. A change in the compressional mechanisms was observed at P ≤ 2 GPa. The P-induced structural rearrangement up to 8.5 GPa is completely reversible. The high thermo-elastic stability of CsAlSi₅O_12, the immobility of Cs at HT/HP-conditions, the preservation of crystallinity at least up to 8.5 GPa and 1,000°C in elastic regime and the extremely low leaching rate of Cs from CsAlSi₅O₁₂ allow to consider this open-framework silicate as functional material potentially usable for fixation and deposition of Cs radioisotopes.     

Variability of Winter-Spring Bloom <Emphasis Type="Italic">Phaeocystis pouchetii</Emphasis> Abundance in Massachusetts Bay

Abundance of the prymnesiophyte Phaeocystis pouchetii was quantified via light microscopy at 2-week to monthly intervals in Massachusetts Bay (southern Gulf of Maine, NW Atlantic) during 1992–2012. Variability in the abundance and seasonal cycle of Phaeocystis are described and synoptic hydrographic, nutrient, and meteorological data were analyzed to identify factors that may influence Phaeocystis abundance. The maximum Phaeocystis abundance was 14?×?10⁶ cells L^?1 (10 Apr 2008). It was frequently (5 of 8 years) absent prior to year 2000, but not thereafter. Seasonally, it first appeared in February to early March, reached peak abundance in mid-April, and persisted until May or early June for a duration of 0–112 days (mean 34 days). A long-term alternation between Phaeocystis and centric diatom abundance was apparent, suggesting winter-spring selection of either Phaeocystis or centric diatoms. Phytoplankton community analysis suggested that blooms affected the rest of the phytoplankton community. Phaeocystis blooms were manifest as a substantial increase in particulate nutrients above normal levels. Phaeocystis blooms were preceded in February by a slightly elevated concentration of NO₃ (9.3 vs. 6.5 μM when absent) and PO₄ (0.99 vs. 0.79 μM when absent). Blooms were also preceded by elevated ratios of NO₃/PO₄, NO₃/Si, and PO₄/Si, and warmer, saltier waters reflecting reduced river discharge. The correlation with salinity and river discharge suggests that Phaeocystis bloom variability is partially determined by annually varying circulation processes that determine the degree of low nutrient, low salinity coastal water intrusion into Massachusetts Bay.     

Elastic behavior of vanadinite,Pb<Subscript>10</Subscript>(VO<Subscript>4</Subscript>)<Subscript>6</Subscript>Cl<Subscript>2</Subscript>, a microporous non-zeolitic mineral

The high-pressure behavior of a vanadinite (Pb₁₀(VO₄)₆Cl₂, a = b = 10.3254(5), c = 7.3450(4) Å, space group P6₃/m), a natural microporous mineral, has been investigated using in-situ HP-synchrotron X-ray powder diffraction up to 7.67 GPa with a diamond anvil cell under hydrostatic conditions. No phase transition has been observed within the pressure range investigated. Axial and volume isothermal Equations of State (EoS) of vanadinite were determined. Fitting the P–V data with a third-order Birch-Murnaghan (BM) EoS, using the data weighted by the uncertainties in P and V, we obtained: V ₀ = 681(1) Å³, K ₀ = 41(5) GPa, and K′ = 12.5(2.5). The evolution of the lattice constants with P shows a strong anisotropic compression pattern. The axial bulk moduli were calculated with a third-order “linearized” BM-EoS. The EoS parameters are: a ₀ = 10.3302(2) Å, K ₀(a) = 35(2) GPa and K′(a) = 10(1) for the a-axis; c ₀ = 7.3520(3) Å, K ₀(c) = 98(4) GPa, and K′(c) = 9(2) for the c-axis (K ₀(a):K ₀(c) = 1:2.80). Axial and volume Eulerian-finite strain (fe) at different normalized stress (Fe) were calculated. The weighted linear regression through the data points yields the following intercept values: Fe _a (0) = 35(2) GPa for the a-axis, Fe _c (0) = 98(4) GPa for the c-axis and Fe _V (0) = 45(2) GPa for the unit-cell volume. The slope of the regression lines gives rise to K′ values of 10(1) for the a-axis, 9(2) for the c-axis and 11(1) for the unit cell-volume. A comparison between the HP-elastic response of vanadinite and the iso-structural apatite is carried out. The possible reasons of the elastic anisotropy are discussed.     

Pressure induced phase transition in Pb<Subscript>6</Subscript>Bi<Subscript>2</Subscript>S<Subscript>9</Subscript>

The crystal structure of Pb₆Bi₂S₉ is investigated at pressures between 0 and 5.6 GPa with X-ray diffraction on single-crystals. The pressure is applied using diamond anvil cells. Heyrovskyite (Bbmm, a = 13.719(4) Å, b = 31.393(9) Å, c = 4.1319(10) Å, Z = 4) is the stable phase of Pb₆Bi₂S₉ at ambient conditions and is built from distorted moduli of PbS-archetype structure with a low stereochemical activity of the Pb²⁺ and Bi³⁺ lone electron pairs. Heyrovskyite is stable until at least 3.9 GPa and a first-order phase transition occurs between 3.9 and 4.8 GPa. A single-crystal is retained after the reversible phase transition despite an anisotropic contraction of the unit cell and a volume decrease of 4.2%. The crystal structure of the high pressure phase, β-Pb₆Bi₂S₉, is solved in Pna2 ₁ (a = 25.302(7) Å, b = 30.819(9) Å, c = 4.0640(13) Å, Z = 8) from synchrotron data at 5.06 GPa. This structure consists of two types of moduli with SnS/TlI-archetype structure in which the Pb and Bi lone pairs are strongly expressed. The mechanism of the phase transition is described in detail and the results are compared to the closely related phase transition in Pb₃Bi₂S₆ (lillianite).     

Compressibility of strontium orthophosphate Sr<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> at high pressure

High pressure in situ synchrotron X-ray diffraction experiment of strontium orthophosphate Sr₃(PO₄)₂ has been carried out to 20.0 GPa at room temperature using multianvil apparatus. Fitting a third-order Birch–Murnaghan equation of state to the P–V data yields a volume of V ₀ = 498.0 ± 0.1 Å³, an isothermal bulk modulus of K _T  = 89.5 ± 1.7 GPa, and first pressure derivative of K _T ′ = 6.57 ± 0.34. If K _T ′ is fixed at 4, K _T is obtained as 104.4 ± 1.2 GPa. Analysis of axial compressible modulus shows that the a-axis (K _a  = 79.6 ± 3.2 GPa) is more compressible than the c-axis (K _c  = 116.4 ± 4.3 GPa). Based on the high pressure Raman spectroscopic results, the mode Grüneisen parameters are determined and the average mode Grüneisen parameter of PO₄ vibrations of Sr₃(PO₄)₂ is calculated to be 0.30(2).     

Thermoelastic properties of chromium oxide Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> (eskolaite) at high pressures and temperatures

A new synchrotron X-ray diffraction study of chromium oxide Cr₂O₃ (eskolaite) with the corundum-type structure has been carried out in a Kawai-type multi-anvil apparatus to pressure of 15 GPa and temperatures of 1873 K. Fitting the Birch–Murnaghan equation of state (EoS) with the present data up to 15 GPa yielded: bulk modulus (K _0,T0), 206 ± 4 GPa; its pressure derivative K′_0,T , 4.4 ± 0.8; (?K _0,T /?T) = ?0.037 ± 0.006 GPa K^?1; a = 2.98 ± 0.14 × 10^?5 K^?1 and b = 0.47 ± 0.28 × 10^?8 K^?2, where α _0,T  = a + bT is the volumetric thermal expansion coefficient. The thermal expansion of Cr₂O₃ was additionally measured at the high-temperature powder diffraction experiment at ambient pressure and α _0,T0 was determined to be 2.95 × 10^?5 K^?1. The results indicate that coefficient of the thermal expansion calculated from the EoS appeared to be high-precision because it is consistent with the data obtained at 1 atm. However, our results contradict α ₀ value suggested by Rigby et al. (Brit Ceram Trans J 45:137–148, 1946) widely used in many physical and geological databases. Fitting the Mie–Grüneisen–Debye EoS with the present ambient and high-pressure data yielded the following parameters: K _0,T0 = 205 ± 3 GPa, K′_0,T  = 4.0, Grüneisen parameter (γ ₀) = 1.42 ± 0.80, q = 1.82 ± 0.56. The thermoelastic parameters indicate that Cr₂O₃ undergoes near isotropic compression at room and high temperatures up to 15 GPa. Cr₂O₃ is shown to be stable in this pressure range and adopts the corundum-type structure. Using obtained thermoelastic parameters, we calculated the reaction boundary of knorringite formation from enstatite and eskolaite. The Clapeyron slope (with \({\text{d}}P/{\text{d}}T = - 0.014\) GPa/K) was found to be consistent with experimental data.     

Detailed comparison of nine intact rock failure criteria using polyaxial intact coal strength data obtained through PFC<Superscript>3D</Superscript> simulations

Study of intact rock failure criteria is an important topic in rock mechanics. In this study, applicability of nine different intact rock failure criteria is investigated for intact coal strength data. PFC^3D modeling was used to simulate the laboratory polyaxial tests for cubic intact coal blocks of side dimension 110 mm under different confining stress combinations. A modified grid search procedure is proposed and used to find the best-fitting parameter values and to calculate the coefficient of determination (R ²) values for each criterion. Detailed comparisons of the nine criteria are made using the following aspects: R ² values, σ ₁ ? σ ₂ plots for different σ ₃, shapes on the deviatoric plane, linearity or nonlinearity on the meridian planes. Through the comparisons of R ² values, σ ₁ ? σ ₂ plots and meridian lines, the modified Wiebols–Cook and modified Lade criteria were found to fit the intact coal strength data best. The nine failure criteria are categorized into three types based on the appearances on the deviatoric plane.     

Structural systematics of Ge substitution in primitive pyroxenes

Pyroxenes of general stoichiometry Mg(Ge _x Si_1?x )O₃ were encountered in attempts to synthesise Ge-substituted talcs at 0.2 GPa, 650–700 °C. Orthopyroxenes (Pbca) of compositions x = 0.21, 0.30, and 0.34 were identified, and also a P2₁/c clinopyroxene of composition x = 0.63, and C2/c clinopyroxenes of compositions x = 0.91 and 1. End-member clinoenstatite MgSiO₃-P2₁/c synthesised at 16 GPa, 1300 °C and transformed from C2/c was also included in the study. Crystal structure refinements using single-crystal XRD data showed that unit-cell parameters vary linearly with Si–Ge for the Pbca and P2₁/c pyroxenes, both of which have two symmetrically non-equivalent tetrahedral chains. Refinement of Si–Ge occupancies at tetrahedral sites showed that the two chains of all primitive pyroxenes have very different compositions, with X_Ge(TB) ? X_Ge(TA). This difference arises from the greater flexibility of the B-chain to rotate in response to tetrahedral expansion due to increasing Ge content. The TA-M2 shared polyhedral edge imposes significant constraints on the flexibility of the A-chain, which can accommodate much less Ge than the B-chain. Linear trends of cell parameters, site occupancies, and structural parameters for the primitive pyroxenes, when extrapolated to published data for MgGeO₃–Pbca, extend across the entire Si–Ge join.     

Water determination in iron oxyhydroxides and iron ores by Karl Fischer titration

Protohematite (Fe_2?x/3(OH) _x O_3?x 1 ≤ x < 0.5) and hydrohematite (Fe_2?x/3(OH) _x O_3?x 0.5 ≤ x < 0) are iron-defective phases containing hydroxyl groups in their structures. These species were described in prior studies mainly with the aid of X-ray diffraction and Infrared spectroscopy. The existence of these phases in soils might have influence in redox processes, and they were considered as a possible water reservoir in Martian soils. In this study, we have used for the first time the Karl Fischer titration method to determine the amount of water released after heating several synthetic samples of goethite, hematite and natural iron ores at 105, 400, 600 and 900 °C. It was found that heating at 105 °C did not remove all moisture from the samples, and higher temperatures were necessary to completely remove all the absorbed water. The water contents determined at 400, 600 and 900 °C were found to be the same within the experimental errors, suggesting the inexistence of both protohematite and hydrohematite in the investigated samples. Therefore, the above-mentioned effects of these phases in soils might have to be reevaluated.     

On the crystal chemistry and elastic behavior of a phlogopite 3<Emphasis Type="Italic">T</Emphasis>

The crystal chemistry and the elastic behavior under isothermal conditions up to 9 GPa of a natural, and extremely rare, 3T-phlogopite from Traversella (Valchiusella, Turin, Western Alps) [(K_0.99Na_0.05Ba_0.01)(Mg_2.60Al_0.20Fe _0.21 ²⁺ )[Si_2.71Al_1.29O₁₀](OH)₂, space group P3₁12, with a = 5.3167(4), c = 30.440(2) Å, and V = 745.16(9) ų] have been investigated by electron microprobe analysis in wavelength dispersion mode, single-crystal X-ray diffraction at 100 K, and in situ high-pressure synchrotron radiation powder diffraction (at room temperature) with a diamond anvil cell. The single-crystal refinement confirms the general structure features expected for trioctahedral micas, with the inter-layer site partially occupied by potassium and sodium, iron almost homogeneously distributed over the three independent octahedral sites, and the average bond distances of the two unique tetrahedra suggesting a disordered Si/Al-distribution (i.e., 〈T1-O〉 ~ 1.658 and 〈T2-O〉 ~ 1.656 Å). The location of the H-site confirms the orientation of the O–H vector nearly perpendicular to (0001). The refinement converged with R ₁(F) = 0.0382, 846 unique reflections with F _O > 4σ(F _O) and 61 refined parameters, and not significant residuals in the final difference-Fourier map of the electron density (+0.77/?0.37 e ^?/ų). The high-pressure experiments showed no phase transition within the pressure range investigated. The P–V data were fitted with a Murnaghan (M-EoS) and a third-order Birch-Murnaghan equation of state (BM-EoS), yielding: (1) M-EoS, V ₀ = 747.0(3) ų, K _T0 = 44.5(24) GPa, and K′ = 8.0(9); (2) BM-EoS, V ₀ = 747.0(3) ų, K _T0 = 42.8(29) GPa, and K′ = 9.9(17). A comparison between the elastic behavior in response to pressure observed in 1M- and 3T-phlogopite is made.     

CO<Subscript>2</Subscript>-assisted removal of nutrients from municipal wastewater by microalgae <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> and <Emphasis Type="Italic">Scenedesmus obliquus</Emphasis>

Axenic culture of microalgae Chlorella vulgaris ATCC^® 13482 and Scenedesmus obliquus FACHB 417 was used for phycoremediation of primary municipal wastewater. The main aim of this study was to measure the effects of normal air and CO₂-augmented air on the removal efficacy of nutrients (ammonia N and phosphate P) from municipal wastewater by the two microalgae. Batch experiments were carried out in cylindrical glass bottles of 1 L working volume at 25 °C and cool fluorescent light of 6500 lux maintaining 14/10 h of light/dark cycle with normal air supplied at 0.2 L min^?1 per liter of the liquid for both algal strains for the experimental period. In the next set of experiments, the treatment process was enhanced by using 1, 2 and 5% CO₂/air (vol./vol.) supply into microalgal cultures. The enrichment of inlet air with CO₂ was found to be beneficial. The maximum removal of 76.3 and 76% COD, 94.2 and 92.6% ammonia, and 94.8 and 93.1% phosphate after a period of 10 days was reported for C. vulgaris and S. obliquus, respectively, with 5% CO₂/air supply. Comparing the two microalgae, maximum removal rates of ammonia and phosphate by C. vulgaris were 4.12 and 1.75 mg L^?1 day^?1, respectively, at 5% CO₂/air supply. From kinetic study data, it was found that the specific rates of phosphate utilization (q _phsophate) by C. vulgaris and S. obliquus at 5% CO₂/air supply were 1.98 and 2.11 day^?1, respectively. Scale-up estimation of a reactor removing phosphate (the criteria pollutant) from 50 MLD wastewater influent was also done.     

A novel halo-alkalo-tolerant bacterium, <Emphasis Type="Italic">Marinobacter alkaliphilus</Emphasis> ABN-IAUF-1, isolated from Persian Gulf suitable for alkaline lipase production

Alkaline lipases are one of the most important industrial enzymes that have several uses in detergents, food, pharmaceutical, cosmetics, textile, leather and biomedical industries. For screening the lipase-producing bacteria, olive agar A, B, C and Rhodamine B agar were used. The best environmental conditions and their interactions for alkaline lipase production were obtained using Taguchi statistical test. Enzyme purification was carried out by ammonium sulfate precipitation, dialysis and SDS-PAGE, respectively. The best alkaline lipase-producing strain, WS3, isolated from Persian Gulf, was named Marinobacter alkaliphilus ABN-IAUF-1 (GenBank accession number: KP403723). The maximum enzyme activity of 37.00 (μ/ml) was measured in the presence of coconut oil as the carbon source in oil broth medium after 48-h incubation at the pH 8.00 and 30 °C. The most effective factors in enzyme production were nitrogen and carbon sources with 32 and 25% of influence, respectively. Precipitation and dialysis increased the enzyme purity 1.90–2.33 times. The total enzyme activity of 925.00 ± 20.00 U in the oil broth, 96.00 ± 7.00 U after precipitation with ammonium sulfate and 60.00 ± 5.00 U after dialysis was measured. The molecular weight of alkaline lipase was measured as 55 kDa. In conclusion, this is the first report of production of alkaline lipase by a halo-alkalophilic bacterium, Marinobacter alkaliphilus ABN-IAUF-1, that was obtained from Persian Gulf, Iran. The application of enzymes produced by extremophiles such as Marinobacter alkaliphilus could be an asset in the modern environmental microbiology as well as food and industrial biotechnology.     

New high-pressure phases in BaCO<Subscript>3</Subscript>

Barium carbonate (BaCO₃) was examined in a diamond anvil cell up to a pressure of 73 GPa using an in situ angle-dispersive X-ray diffraction technique. Three new phases of BaCO₃ were observed at pressures >10 GPa. From 10 to 24 GPa, BaCO₃-IV had a post-aragonite structure with space group Pmmn. There are two molecules in a single unit cell (Z = 2) of the orthorhombic phase, which is same as the high-pressure phases of CaCO₃ and SrCO₃. The isothermal bulk modulus of BaCO₃-IV is K ₀ = 84(4) GPa, with V ₀ = 129.0(7) Å³ when K ₀′ = 4. The c axis of the unit cell parameter is less compressible than the a and b axes. The relative change in volume that accompanies the transformation between BaCO₃-III and BaCO₃-IV is ～6%. BaCO₃-V, which has an orthorhombic symmetry, was synthesized at 50 GPa. As the pressure increases, BaCO₃-V is transformed into tetragonal BaCO₃-VI. This transformation is likely to be second order, because the diffraction pattern of BaCO₃-V is similar to that of BaCO₃-VI, and some single peaks in BaCO₃-VI become doublets in BaCO₃-V. After decompression, the new high-pressure phases transform into BaCO₃-II. Our findings resolve a dispute regarding the stable high-pressure phases of BaCO₃.     

The crystal structure and thermal expansion tensor of MgSO<Subscript>4</Subscript>–11D<Subscript>2</Subscript>O(meridianiite) determined by neutron powder diffraction

We have collected high-resolution neutron powder diffraction patterns from MgSO₄·11D₂O over the temperature range 4.2–250 K. The crystal is triclinic, space-group \( \text{P} \bar{1} \) (Z = 2) with a = 6.72746(6) Å, b = 6.78141(6) Å, c = 17.31803(13) Å, α = 88.2062(6)°, β = 89.4473(8)°, γ = 62.6075(5)°, and V = 701.140(6) ų at 4.2 K, and a = 6.75081(3) Å, b = 6.81463(3) Å, c = 17.29241(6) Å, α = 88.1183(3)°, β = 89.4808(3)°, γ = 62.6891(3)°, and V = 706.450(3) ų at 250 K. Structures were refined to wRp = 3.99 and 2.84% at 4.2 and 250 K, respectively. The temperature dependence of the lattice parameters over the intervening range have been fitted with a modified Einstein oscillator model which was used to obtain the coefficients of the thermal expansion tensor. The volume thermal expansion, α_V, is considerably smaller than ice Ih at all temperatures, and smaller even than MgSO₄·7D₂O (although ?α_V/?T is very similar for both sulfates); MgSO₄·11D₂O exhibits negative α_V below 55 K (compared to 70 K in D₂O ice Ih and 20 K in MgSO₄·7D₂O) The relationship between the magnitude and orientation of the principal axes of the expansion tensor and the main structural elements are discussed.     

The effect of alkalis and polymerization on the solubility of H<Subscript>2</Subscript>O and CO<Subscript>2</Subscript> in alkali-rich silicate melts

The effect of alkalis on the solubility of H₂O and CO₂ in alkali-rich silicate melts was investigated at 500 MPa and 1,250 °C in the systems with H₂O/(H₂O + CO₂) ratio varying from 0 to 1. Using a synthetic analog of phonotephritic magma from Alban Hills (AH1) as a base composition, the Na/(Na + K) ratio was varied from 0.28 (AH1) to 0.60 (AH2) and 0.85 (AH3) at roughly constant total alkali content. The obtained results were compared with the data for shoshonitic and latitic melts having similar total alkali content but different structural characteristics, e.g., NBO/T parameter (the ratio of non-bridging oxygens over tetrahedrally coordinated cations), as those of the AH compositions. Little variation was observed in H₂O solubility (melt equilibrated with pure H₂O fluid) for the whole compositional range in this study with values ranging between 9.7 and 10.2 wt. As previously shown, the maximum CO₂ content in melts equilibrated with CO₂-rich fluids increases strongly with the NBO/T from 0.29 wt % for latite (NBO/T = 0.17) to 0.45 wt % for shoshonite (NBO/T = 0.38) to 0.90 wt % for AH2 (NBO/T = 0.55). The highest CO₂ contents determined for AH3 and AH1 are 1.18 ± 0.05 wt % and 0.86 ± 0.12 wt %, respectively, indicating that Na is promoting carbonate incorporation stronger than potassium. At near constant NBO/T, CO₂ solubility increases from 0.86 ± 0.12 wt % in AH1 [Na/(Na + K)] = 0.28, to 1.18 ± 0.05 wt % in AH3 [Na/(Na + K)] = 0.85, suggesting that Na favors CO₂ solubility on an equimolar basis. An empirical equation is proposed to predict the maximum CO₂ solubility at 500 MPa and 1,100–1,300 °C in various silicate melts as a function of the NBO/T, (Na + K)/∑cations and Na/(Na + K) parameters: \({\text{wt}}\% \;{\text{CO}}_{2} = - 0.246 + 0.014\exp \left( {6.995 \cdot \frac{\text{NBO}}{T}} \right) + 3.150 \cdot \frac{{{\text{Na}} + {\text{K}}}}{{\varSigma {\text{cations}}}} + 0.222 \cdot \frac{\text{Na}}{{{\text{Na}} + {\text{K}}}}.\) This model is valid for melt compositions with NBO/T between 0.0 and 0.6, (Na + K)/∑cation between 0.08 and 0.36 and Na/(Na + K) ratio from 0.25 to 0.95 at oxygen fugacities around the quartz–fayalite–magnetite buffer and above.