氧化铁矿物对五氯苯酚表面吸附实验及其反应模式

批量法实验研究表明,五氯苯酚 (PCP)在合成的针铁矿、纤铁矿和赤铁矿表面吸附的浓度等温线为饱和型特征,可用 Langmuir公式拟合,而 pH吸附等温线为峰型曲线,峰值在 pH≈ 5. 矿物表面化合态和 PCP溶液离子化合态分析与计算表明, PCP在氧化铁矿物表面存在两种吸附反应模式,即表面静电吸附反应和表面络合吸附反应,表面静电吸附反应常数比表面络合吸附反应常数高 1～ 2个数量级.并进一步从反应机制上证明了憎水型可离解有机化合物 (HIOCs)在矿物表面吸附的模式与趋向性.     

合成铁氧化物矿物对苯酚的吸附实验研究

采用TEM、X射线衍射分析及BET比表面积测定等手段对合成的针铁矿、赤铁矿两种矿物进行表征,对此两种矿物对苯酚的吸附特性并批处理吸附实验研究结果表明,针铁矿对苯酚的吸附量大于赤铁矿的吸附量;针铁矿吸附苯酚的pH吸收边为峰型曲线,且峰值在pH 7～8。Langmuir方程拟合结果的吻合程度较之Henry线性方程与Freundlich方程高。实验中氧化铁矿物表面对苯酚的吸附则主要表现为表面分子吸附,可能存在表面疏水性作用,而静电离子交换和表面配合吸附模式不明显。     

五氯苯酚在矿物表面吸附——实验、表面反应模式及其环境意义

利用批量平衡技术研究了石英、高岭石、伊利石、蒙脱石和铁氧化物对五氯苯酚(PCP)吸附的pH关系等温线和浓度关系等温线,发现所有矿物的pH关系等温线都表现出典型的峰形曲线特征,峰位在pH=5～6之间,依矿物不同而不同。基于矿物表面羟基位化合态和PCP的化合态考虑,提出一种包含表面络合反应和表面静电吸附反应的模式,对pH关系等温线计算拟合发现有很好的相关性。模式计算还表明,石英和层状硅酸盐矿物对PCP吸附以表面络合反应为主,而氧化铁矿物则包含表面络合反应和表面静电吸附反应,但以后者占主导,其反应平衡常数比前者大1～3个数量级。高岭石和氧化铁矿物的浓度吸附等温线可用Langmuir方程很好拟合,最大吸附量的大小顺序是赤铁矿>纤铁矿>针铁矿>高岭石>石英>蒙脱石≈伊利石,并可以用矿物表面羟基位浓度和反应机制加以解释。PCP在矿物表面可观的吸附量说明矿物表面吸附对憎水性可离解有机化合物(HIOCs)在天然水相体系和沉积中的迁移转化过程起着相当重要的作用。     

五氯苯酚在氧化物和粘土矿物表面吸附:表面反应模式及其环境意义

石英、高岭石、伊利石、蒙脱石和铁氧化物对五氯苯酚(PCP)吸附的pH关系等温线和浓度关系等温线已用批量平衡技术进行研究。所有矿物的pH关系等温线都表现出典型的峰形曲线特征,峰位在pH=5~6之间,依矿物不同而不同。基于矿物表面羟基位化合态和PCP的化合态考虑,研究提出一种包含表面络合反应和表面静电吸附反应的模式,对pH关系等温线计算拟合发现有很好的相关性。模式计算还表明,石英和层硅酸盐矿物对PCP吸附以表面络合反应为主,而氧化铁矿物则既包含表面络合反应,又包含表面静电吸附反应,但以后者占主导,其反应平衡常数比前者大1~3个…     

针铁矿/水界面反应性的实验研究

选择针铁矿对Pb2+、Cu2+、Cd2+等3种重金属离子的吸附实验,开展矿物/水界面反应性研究.金属离子(M2+)在矿物-水溶液间分配有多种表面反应机制,这些表面反应发生作用的条件主要取决于吸附质水化学性质和矿物表面荷电性,因此,溶液pH值是影响矿物/水界面反应性的关键因素.在不同pH值条件下, 表面羟基可通过发生质子化或去质子化反应而使得矿物表面产生荷电性并发生改变,而金属离子的水解则可显著加快金属羟基配合物的形成,从而进一步增强了矿物/水界面反应.本实验条件下针铁矿表面对重金属离子的吸着量随pH值升高而升高,在一个较窄的pH值范围内吸附率急剧升高,呈S形分布.针铁矿对3种不同的重金属离子的吸附能力的强弱顺序是Cu2+＞Pb2+＞Cd2+.无论是Langmuir方程还是Freundlich方程,都能较好拟合针铁矿对重金属离子的等温吸附过程.Freundlich方程的n值均在0.1～0.5之间,说明重金属离子在针铁矿表面的吸附并不能简单地归结为单配位或双配位模式,可能存在着多种吸附结合形态.表观吸附常数KM值的变化规律,说明重金属离子与针铁矿表面反应模式及其表面吸附形态发生了变化,具体的吸附形态还有待谱学研究进一步证实.     

铁锰氧化物在碱性条件下对镉的吸附特征研究

实验研究了不同的pH值、初始离子浓度、矿物用量、温度以及时间等因素对针铁矿和软锰矿吸附镉的影响。结果表明:在pH值从酸性到近中性的范围内,两种氧化矿物对镉的吸附量增加较快,然后在碱性条件下吸附量保持着最大值;反应前后两种氧化矿物溶液的pH值均有不同程度的变化,其中针铁矿和软锰矿的临界pH值分别为8和6.5;两种矿物对镉的吸附在6 h左右达到了吸附平衡,吸附等温线都较好地符合Freundlich等温方程式;随着两种氧化物用量的增加,其吸附量也有增加;室温下,针铁矿和软锰矿对镉的吸附效果较好。     

铁锰氧化物对苯酚氧化降解的实验研究

为了考察铁锰氧化物对酚类污染物的氧化降解能力,采用天然以及合成的铁锰氧化物对苯酚的氧化降解进行对比实验研究。土壤中铁锰氧化物样品分别为天然针铁矿及氧化锰,合成铁锰氧化物样品分别为合成针铁矿及软锰矿。结果表明：苯酚与铁锰氧化物发生氧化还原作用时,还可能与土壤中杂质发生吸附等作用;铁锰氧化物还原反应强度随着反应介质pH值的升高而迅速下降;可用零级反应动力学方程拟合铁氧化物还原溶解反应,针铁矿溶解反应的强度与介质的pH值呈负相关关系;天然针铁矿对酚类污染物的氧化降解能力明显高于合成针铁矿,pH值对天然针铁矿溶解反应影响较大;可用一级指数衰减方程拟合锰氧化物还原溶解反应,锰氧化物溶解反应的强度与介质的pH值呈指数衰减关系;pH值对软锰矿还原溶解反应的影响大于对土壤中氧化锰的影响,pH值越小,影响越显著;对比pH值对铁和锰还原作用的影响发现,在pH=6.5时,锰氧化物仍有较强的氧化性能。     

矿物溶解的表面化学动力学机理

本文应用表面化学理论分析了矿物在水溶液中的溶解反应动力学机理。表面化学的催化作用使矿物溶解反应的活化能显著降低。矿物溶解速率受表面吸附、表面交换反应和解吸反应等表面化学过程的控制并与溶液的pH值有关，正比于溶液αH＋值的nθ次幂。受表面吸附控制时，nθ＝1，溶解速率随pH增大而减小；受表面交换反应控制时，nθ＝0，溶解速率与pH无关；受解吸反应控制时，酸性条件下nθ为0～1内的正小数，碱性条件下nθ为-1～0之内的负小数。大多数矿物的溶解作用在酸性条件下受表面吸附和／或表面交换反应控制，在碱性条件下受解吸反应的控制。     

多粘芽孢杆菌(Paenibacillus polymyxa)吸附Cu2+的实验研究

细菌表面往往存在多种化学基团,能够通过吸附作用影响环境流体中金属元素的活动性,从而与表生条件下的元素富集、矿物成核结晶等地球化学过程密不可分。为了深入认识细菌吸附作用的地球化学意义和环境效应,揭示细菌吸附金属离子的热力学行为,选择了多粘芽孢杆菌(Paenibacillus polymyxa)为研究细菌,系统开展了滴定实验和Cu2 吸附实验。通过连续酸滴定方法分析了细菌表面的化学特征,发现多粘芽孢杆菌在pH值为7.54~6.50范围内,表面带负电荷,表现出质子吸附行为;设计开展了Cu2 吸附实验,发现溶液的pH值对Cu2 吸附有一定影响,可能存在Cu2 与细菌表面质子的交换作用;根据Cu2 吸附等温线拟合计算,发现吸附等温线符合Langmuir和Freundlich吸附模型,根据Langmuir模型计算得到每个细胞的Cu2 饱和吸附量高达1.69×10-7mg。     

高岭石和硅／铝-氧化物对腐殖酸的吸附实验研究

矿物结合的腐殖质可改变矿物的表面性质,矿物对腐殖酸的吸附强度与矿物的吸附位性质、密度、荷电性及比表面积有关.若按比表面积计算,矿物对腐殖酸的吸附强度顺序为氢氧化铝>高岭石>石英;按单位质量计算,吸附强度顺序为高岭石>氢氧化铝>石英.研究表明,矿物表面活性受水溶液pH值的调控,且当pH值在4～7时,上述3种矿物对腐殖酸的吸附机理为石英主要表现为氢键作用;氢氧化铝主要表现为配体交换表面配位作用;高岭石表现为多种形式并存,包括氢键、配体交换表面配位和疏水性作用以及金属离子桥键作用.     

针铁矿和蒙脱石对菲的吸附解吸行为与热力学研究

采用批量振荡吸附平衡法设计针铁矿和蒙脱石对菲的吸附解吸试验,对比研究了针铁矿和蒙脱石对菲的吸附解吸行为,并考察了不同K＋浓度的溶液对蒙脱石吸附菲的影响,比较分析了线性吸附模型和Freundlich吸附模型描述矿物吸附等温线的准确性,并从吸附热力学角度探讨了矿物的吸附机理。结果表明：针铁矿和蒙脱石对菲的吸附解吸均表现出明显的非线性和解吸滞后现象;相对于线性吸附模型来说,针铁矿和蒙脱石对菲的吸附解吸更符合Freundiich吸附模型;与蒙脱石相比,针铁矿对菲的吸附更为显著,且具有更好的稳定性;溶液中软阳离子K＋的存在使蒙脱石对菲的吸附能力得到显著提高;菲在蒙脱石和针铁矿上的吸附过程是一个自发放热,同时伴随着熵值减小的过程;随着温度的升高,蒙脱石和针铁矿对菲的吸附能力均减弱。     

Adsorption of Pentachlorophenol onto Oxide and Clay Minerals： Surface Reaction Model and Environmental Implications

The adsorption of pentachlorophenol （PCP） onto quartz, kaolinite, illite, montmorillonite and iron oxides has been investigated by batch equilibrium techniques. The pH-dependent isotherms are curves with peak values, the position of which is at about pH = 5-6 depending on the mineral species. Based on distribution of both speciation of surface hydroxyls on minerals and PCP in solution a surface reaction model involving surface complexation and surface electrostatic attraction is presented to fit the pH-dependent isotherms, and both reaction constants are calculated. The results show that on quartz and phyllosilicate minerals the predominant adsorption reaction is surface complexation, meanwhile both of surface electrostatic attraction and surface complexation are involved on the iron oxide minerals. The reaction constants of surface electrostatic adsorption are usually one to three orders in magnitude, larger than that of surface complexation. The concentration-dependent isotherms can be well fitted by Langmnir equation with the correlation coefficient R〉0.93 for kaolinite and iron oxides. The maximum adsorption is found in the order： hematite 〉 lepidocrocite 〉 goethite 〉 kaolinite 〉 quartz 〉 montmorillonite ≈ illite, which can be interpreted by consideration of both reaction mechanism and surface hydroxyl density. The significant adsorption of PCP onto mineral surfaces suggests that clay and iron oxide minerals will play an important role as HIOCs are adsorbed in laterite or latertoid soil, which is widespread in South China.     

The mechanism of cadmium surface complexation on iron oxyhydroxide minerals

Many sediment and soil systems have become significantly contaminated with cadmium, and earth scientists are now required to make increasingly accurate predictions of the risks that this contamination poses. This necessitates an improved understanding of the processes that control the mobility and bioavailability of cadmium in the environment. With this in mind, we have studied the composition and structure of aqueous cadmium sorption complexes on the iron oxyhydroxide minerals goethite (α-FeOOH), lepidocrocite (γ-FeOOH), akaganeite (β-FeOOH), and schwertmannite (Fe₈O₈(OH)₆SO₄) using extended X-ray adsorption fine structure spectroscopy. The results show that adsorption to all of the studied minerals occurs via inner sphere adsorption over a wide range of pH and cadmium concentrations. The bonding mechanism varies between minerals and appears to be governed by the availability of different types of adsorption site at the mineral surface. The geometry and relative stability of cadmium adsorption complexes on the goethite surface was predicted with ab initio quantum mechanical modelling. The modelling results, used in combination with the extended X-ray adsorption fine structure data, allow an unambiguous determination of the mechanism by which cadmium bonds to goethite.Cadmium adsorbs to goethite by the formation of bidentate surface complexes at corner sharing sites on the predominant (110) crystallographic surface. There is no evidence for significant cadmium adsorption to goethite at the supposedly more reactive edge sharing sites. This is probably because the edge sharing sites are only available on the (021) crystallographic surface, which comprises just ∼2% of the total mineral surface area. Conversely, cadmium adsorption on lepidocrocite occurs predominately by the formation of surface complexes at bi- and/or tridentate edge sharing sites. We explain the difference in extended X-ray adsorption fine structure results for cadmium adsorption on goethite and lepidocrocite by the greater availability of reactive edge sharing sites on lepidocrocite than on goethite. The structures of cadmium adsorption complexes on goethite and lepidocrocite appear to be unaffected by changes in pH and surface loading. There is no support for cadmium sorption to any of the studied minerals via the formation of an ordered precipitate, even at high pH and high cadmium concentration. Cadmium adsorption on akaganeite and schwertmannite also occurs via inner sphere bonding, but the mechanism(s) by which this occurs remains ambiguous.     

Impacts of hydrous manganese oxide on the retention and lability of dissolved organic matter

Minerals constitute a primary ecosystem control on organic C decomposition in soils, and therefore on greenhouse gas fluxes to the atmosphere. Secondary minerals, in particular, Fe and Al (oxyhydr)oxides—collectively referred to as “oxides” hereafter—are prominent protectors of organic C against microbial decomposition through sorption and complexation reactions. However, the impacts of Mn oxides on organic C retention and lability in soils are poorly understood. Here we show that hydrous Mn oxide (HMO), a poorly crystalline δ-MnO₂, has a greater maximum sorption capacity for dissolved organic matter (DOM) derived from a deciduous forest composite O_i, O_e, and O_a horizon leachate (“O horizon leachate” hereafter) than does goethite under acidic (pH 5) conditions. Nonetheless, goethite has a stronger sorption capacity for DOM at low initial C:(Mn or Fe) molar ratios compared to HMO, probably due to ligand exchange with carboxylate groups as revealed by attenuated total reflectance-Fourier transform infrared spectroscopy. X-ray photoelectron spectroscopy and scanning transmission X-ray microscopy–near-edge X-ray absorption fine structure spectroscopy coupled with Mn mass balance calculations reveal that DOM sorption onto HMO induces partial Mn reductive dissolution and Mn reduction of the residual HMO. X-ray photoelectron spectroscopy further shows increasing Mn(II) concentrations are correlated with increasing oxidized C (C=O) content (r = 0.78, P < 0.0006) on the DOM–HMO complexes. We posit that DOM is the more probable reductant of HMO, as Mn(II)-induced HMO dissolution does not alter the Mn speciation of the residual HMO at pH 5. At a lower C loading (2 × 10² μg C m^?2), DOM desorption—assessed by 0.1 M NaH₂PO₄ extraction—is lower for HMO than for goethite, whereas the extent of desorption is the same at a higher C loading (4 × 10² μg C m^?2). No significant differences are observed in the impacts of HMO and goethite on the biodegradability of the DOM remaining in solution after DOM sorption reaches steady state. Overall, HMO shows a relatively strong capacity to sorb DOM and resist phosphate-induced desorption, but DOM–HMO complexes may be more vulnerable to reductive dissolution than DOM–goethite complexes.     

DOM不同分子质量组分对石英砂吸附卡马西平的影响研究

为探究溶解性有机质(DOM)不同相对分子质量组分对药物和个人护理品(PPCPs)类污染物吸附过程的影响,以卡马西平(CBZ)为目标污染物,以石英砂代表无机矿物,用商用腐殖酸(HA)制备DOM并进行超滤分级,然后开展吸附实验,并采用荧光光谱和红外光谱表征等手段,研究了DOM不同分子质量组分对石英砂吸附CBZ的影响及机制。结果表明,以3 000和10 000的超滤膜进行分级后的不同相对分子质量HA结构有明显差别,大分子质量HA中苯环等疏水性结构以及羟基的含量较多,芳香构造化程度高,多为分子量较高、稳定性较好的疏水性有机物,但中、小分子质量HA结构差异不大,含有更多羰基、羧基等含氧官能团,主要是一些分子质量较小的亲水物质; DOM不同分子质量组分对CBZ在石英砂上的吸附有明显影响,其中大分子质量组分促进吸附,而中、小分子质量组分抑制吸附,原因在于大分子质量组分可疏水结合于矿物表面,增加介质表面的活性吸附位点,同时其芳香性或脂肪性结构可与CBZ的疏水基团发生疏水作用共吸附或累积吸附于介质表面,从而促进CBZ的吸附;而中、小分子质量DOM的极性官能团可与CBZ酰胺部分通过极性作用结合,对CBZ分子有增溶作用,从而抑制吸附。     

Effects of photoirradiation on the adsorption of dissolved organic matter to goethite

The effects of photoirradiation of dissolved organic matter (DOM) on its subsequent adsorption to the Fe(III)oxyhydroxide mineral goethite were investigated at 22°C in 0.10 mol L⁻¹ NaClO₄ solutions at pH 3.5 and 5.5, Photoirradiation of DOM decreased the abundance of high molecular-weight components and formed new lower molecular-weight components, including low molecular weight carboxylic acids (i.e., formic, malonic, and acetic acids). Adsorption of non-irradiated DOM decreased from pH 3.5 to 5.5 and was dominated by the intermediate molecular weight (1251-3750 Da) fraction, although the 451-1250 and 3751-11350 Da fractions also contributed to adsorption at pH 3.5. Irradiation resulted in a substantial decrease in DOM adsorption affinity at pH 3.5, primarily due to loss of components in the 1251-3750 and 3751-11350 Da fractions. Irradiation resulted in only a small decrease in DOM adsorption affinity at pH 5.5; the loss of components in the 3751-11350 Da fraction upon irradiation had little effect on adsorption because they played little or no role in the non-irradiated sample at this pH. Irradiation of DOM also affected its interactions with Fe in solution and the solution iron(II)/iron(III) speciation. The combined effects of irradiation followed by adsorption produced DOM that was lower in molecular weight and had a decreased UV-Vis absorptivity than either process, alone. Together, these two processes are likely to have important environmental consequences in terms of UV penetration of surface waters, contaminant mobility, and DOM bioavailability.     

Effect of pH on binding of pyrene to hydrophobic fractions of dissolved organic matter (DOM) isolated from lake water

In order to better understand the compositional and structural complexity of dissolved organic matter (DOM) macromolecules and provide mechanistic information on the binding of hydrophobic organic contaminants (HOCs) to DOM, we fractionated large amounts of lake water into three hydrophobic DOM-fractions. The variation of the partitioning coefficients (K _DOC) of pyrene at different pH levels was examined by florescence quenching titration. Results show that, relative to the more polar acidic DOM-fractions, the hydrophobic neutral fraction exhibits a higher sorption ability to pyrene. Generally, the sorption of pyrene to the three hydrophobic fractions is strongly pH-dependent. The K _DOC values of pyrene generally increase with decreasing pH levels, which is especially obvious in the sorption of pyrene to the fulvic acid fractions, suggesting that the binding is controlled by hydrophobic interactions. The mechanisms underlying the binding of pyrene to the hydrophobic fractions were also discussed. Our data are beneficial to further understanding the binding of HOCs to DOM and how it has been affected, which may result in more accurate predictions of K _DOC.     

氧化锰、氧化铁、氧化铝对砷(Ⅲ)的吸附行为研究

合成了氧化锰、氧化铁、氧化铝三种矿物,以氧化铁、氧化锰为吸附剂研究了pH值、离子强度和时间等因素对吸附As(Ⅲ)的影响,并讨论了氧化锰、氧化铁、氧化铝三种矿物对As(Ⅲ)的饱和吸附容量及等温吸附实验。pH值对氧化锰吸附As(Ⅲ)几乎不影响,对氧化铁吸附As(Ⅲ)在很大的范围内(pH为3.5~8.5)影响不大,离子强度对二者吸附As(Ⅲ)的影响不大,吸附反应在0.5 h左右达到吸附平衡。在优化吸附条件下氧化锰、氧化铁、氧化铝对As(Ⅲ)的饱和吸附容量分别为48.38 mg/g、23.70 mg/g、3.52mg/g,三种合成矿物对As(Ⅲ)的饱和吸附容量:氧化锰氧化铁氧化铝。对实验数据进行Freundlich和Langmuir拟合,相关系数R均在0.98以上,吸附动力学符合Lagergren二级速率方程。