王水溶解矿样后酸不溶物中的残留金

地质样品中痕量Au的分析较多采用湿法溶解样品。最常见的是采用浓王水或1 1王水在烧杯或聚碳酸酯溶矿瓶中溶解样品。对于王水能否把地质样品中的痕量Au全部溶出,在酸不溶物中残留多少Au,残留量对分析质量是否有影响的问题,各文献提法不一。文献介绍:王水溶解低含量Au样时偏低15％;溶解石英岩尾矿,Au结果偏低10-30％。又指出:在金矿区围岩和某些酸难溶硅酸盐矿物中采用王水分解样品,在溶矿时不加入HF作助溶剂,其Au结     

泡塑分离冷原子荧光测定金矿中微量汞

冷蒸气原子荧光测Hg,Au的最大允许量为0.5μg。一些金矿样品中Au的含量较高,在分析中如不分离Au而直接测Hg,将产生严重负干扰。本文试验表明:在5％～15％的王水介质中,小于10μg量的Hg不被泡塑吸附;500μgAu被定量吸附,同时被吸附的有Sb、Tl等元素。Se、Te的干扰用K_2Cr_2O_7氧化消除。本法操作简便、快速,分离效果好,成功地应用于金矿样品中Hg的测定。     

哇洪山断裂带中段锌铅银铜金等多金属找矿评价工作取得重要突破

笔者等在哇洪山断裂带中段发现了多条品位较高的锌铅银等多金属矿化带。野外构造地球化学剖面样品经青海省第八地质队和河北地矿局廊坊物探实验室原子吸收光谱定量分析(部分进行了化学分析),此区数个剖面Zn、Pb、Ag、Cu、Au等元素含量达到或远大于工业品位。ZP7剖面18个样品中,5个Pb含量>1％,最高达3.71％;7个Zn含量>1％,最高达3.59％;6个Ag单项分析样品中4个Ag含量>30×10~(-6),最高达424×10~(-6);此外部分样品还伴生金,1个样品Au含量达到1.776×10~(-6)。该剖面区含矿多金属矿化蚀变破碎带露头长度300余米,控制宽度2～5m。ZP19剖面有3处样品铅锌含量大于0.1％,其中Pb最高为2.11％,Zn最高为0.64％,并见到致密铅锌矿化团块1处,该致密方铅矿化团块Pb含量为23.8％,Zn含量为6.15％,Cu含量为0.42％,Ag含量高达476×10~(-6)。ZP21剖面中7个样品锌铅银含量大于或接近工业品位,Pb最高达1.18％,Zn最高达     

西藏尼玛砂金矿中金和银的提纯与精炼

为提纯与精炼西藏尼玛砂金矿中的金和银，在王水介质中制作供还原的Au液，选择草酸作为还原剂很容易将Au还原，而且不与其他金属离子反应。砂金的提纯与精炼要经还原Au液、排除HNO3和砂金的2次溶解及Au的还原。尾渣以NaCO3、硼砂、KNO3为配料在焦炭炉中进行熔炼和泼珠，进而分离出金、银。在提取银的操作中，采用饱和NaCl水溶液。制定的金、银王水法提纯与精炼流程所产出金锭的成色大于等于99．99％，银锭成色大于等于99．90％。     

金在地幔矿物中的赋存形式及其赋存介质转化的可能模式:以中国北方一些地幔橄榄岩包体为例

采集中国北方玄武岩中橄榄岩包体样品21件。测定了其中的主元素、微量元素、稀土元素(REE)和Au等的含量。橄榄岩包体中的Au含量与CaO含量的相关性表明,其中的Au可能主要赋存于单斜辉石中,反映Au含量可能与地幔演化及熔融程度有关;橄榄岩包体后期受地幔流体交代作用的影响,Au转而以硫化物形式存在,这一过程是在橄榄岩包体原有Au的物质基础上进行的。     

金矿样品加工讨论

制样在地质冶金分析工作中有重要作用。尤其是金在自然界赋存状态的特殊性、金粒的延展性以及制样加工设备限制等原因,金矿样品制备的难度较大,但有关报道不多,又特别对含Au、Ag、Cu、Pb、Zn、Bi等的复合矿物制样工作报道更少。 由于长期以来多强调测定的重要性,而忽视试样制备加工程序。制样误差远远超过分析误差导致实验失败的事例是较多的,这给矿山地质、黄金生产和工矿销售等带来不少问题。因此,对复合矿物和多元含金银的有色金属硫化矿和氧化矿试样制备的研究是有益的。     

微孔滤膜制片X射线荧光光谱法测定矿石中银

在氨性介质中以水合联氨还原,Au兼作载体和内标,微孔滤膜制片,XRF测定Ag的方法应用于银矿标准物质及铜矿、铅锌矿、低品位金矿样品中x～xxxμg/g含量Ag的测定。分析结果的RSD优于3％,准确度与常规方法相当。     

混合吸附剂分离富集-电感耦合等离子体质谱法测定地质样品中铂钯金

贵金属分析应用火试金法分离富集时,试金配料复杂、耗时较长,分析成本相对较高,空白较难控制.本文建立了采用过氧化氢-盐酸湿法分解样品,电感耦合等离子体质谱同时测定地质样品中Pt、Pd、Au的分析方法.在10％的盐酸介质中,以LSC-400巯基树脂和活性炭为混合吸附剂,采用动态吸附方式对样品中的Pt、Pd、Au分离富集,用Lu作内标元素,195 Pt、197 Au、108 Pd为待测同位素消除了非谱线干扰和谱线干扰,三元素的回收率均大于96.4％.方法检出限(3σ):Pt为0.06 ng/g,Pd为0.08 ng/g,Au为0.12 ng/g,优于火试金等其他分离富集方法的检出限.应用于测定国家标准物质,Pt、Pd、Au的测定结果与标准值相符,12次测定的相对标准偏差均小于16.1％,满足区域地球化学调查样品的分析要求.该方法操作简便、成本低廉,提高了分析速度,有效地降低了测试过程的空白值.     

小试金光谱法同时测定地质样品中超痕量铂钯金

用小试金光谱法同时测定地质样品中低至0·x×10~(-9)级Pt、Pd和Au,包括先用小试金熔炼和灰吹预富集10g样品中的Pt、Pd和Au于1mg的银合粒中,然后把银合粒装入石墨电极同锇-锑合金(ω(Os)=0.06)一起激发,以发射光谱法同时测定它们的含量。小试金法类同经典火试金,但采用纯化过的2PbCO_3·Pb(OH)_2(Pt、Pd和Au的含量皆<0.05 ×10~(-9)代替商品PbO,并且用50ml高铝坩埚在950℃进行熔炼。方法的检出限是Pt0.2×10~(-9),Pd和Au均为0.1×10~(-9)。对于3×10~(-9)的含量,全过程的相对标准偏差(％)是Pt15,Pd11,Au9。此法快速、简便,适用于地质物料的分析。     

甘肃岷县章（哈寨）—包（家沟）金矿矿石组分含金性研究

甘肃省岷县章（哈寨）—包（家沟）金矿矿石样品化学分析测试结果,经多次内检发现部分样品Au的分析结果误差较大,推测样品中可能有较大颗粒明金存在。为此,采用简易人工重砂方法对矿区两种类型金矿石进行了矿物分离,再分别进行含金性研究,找出样品分析化验结果跳跃误差的原因,探求更为适宜的分析测试方法。     

Wavelength-dispersive X-ray fluorescence spectrometric determination of Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites

Komatiites are mantle-derived ultramafic volcanic rocks. Komatiites have been discovered in several States of India, notably in Karnataka. Studies on the distribution of trace-elements in the komatiites of India are very few. This paper proposes a simple, accurate, precise, rapid, and non-destructive wavelength-dispersive x-ray fluorescence (WDXRF) spectrometric technique for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in komatiites, and discusses the accuracy, precision, limits of detection, x-ray spectral-line interferences, inter-element effects, speed, advantages, and limitations of the technique. The accuracy of the technique is excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Zr, Nb, Ba, Pb, and Th and very good (within 4%) for Y. The precision is also excellent (within 3%) for Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th. The limits of detection are: 1 ppm for Sc and V; 2 ppm for Cr, Co, and Ni; 3 ppm for Cu, Zn, Rb, and Sr; 4 ppm for Y and Zr; 6 ppm for Nb; 10 ppm for Ba; 13 ppm for Pb; and 14 ppm for Th. The time taken for determining Sc, V, Cr, Co, Ni, Cu, Zn, Rb, Sr, Y, Zr, Nb, Ba, Pb, and Th in a batch of 24 samples of komatiites, for a replication of four analyses per sample, by one operator, using a manual WDXRF spectrometer, is only 60 hours.     

高压微波消解法测定醋酸纤维过滤器采集的微尘粒子中的砷镉钴铬铜铁锰镍铅钒锌

最新的流行病学研究表明,空气中较高浓度的悬浮细颗粒可能对人类的健康有不利的影响。根据该项研究显示,由于心脏病、慢性呼吸问题和肺功能指标恶化而导致死亡率的升高与细尘粒子有关。这些研究结果已经促使欧盟于1999年4月出台了限制空气中二氧化硫、二氧化氮、氧化氮、铅和颗粒物含量的法案(1999/30/EC),对各项指标包括对可吸入PM10颗粒的浓度提出了新的限制性指标。PM10颗粒是指可以通过预分级器分离采集的气体动力学直径小于10μm的细颗粒。目前研究的兴趣重点逐步偏向PM2.5这些更细微颗粒物,PM2.5这种颗粒物对健康有明显的不利影响。在欧盟指令2008/50/EC中,对PM10和PM2.5都提     

硅酸盐类样品中硅、铁、铝、钛、锰、钙、镁、钾、钠和磷的x射线荧光光谱测定

本文拟定了一种以熔融法制备样片,用X射线荧光光谱测定硅酸盐类样品中Si、Fe、Al、Tj、Mn、Ca、Mg、K、Na、P等元素的分析方法。在对不同靶材X光管和分光晶体实验对比的基础上,选择了最佳的测量条件。该法具有快速、准确,测量范围广,检测限低,价格便宜等优点。经过近百个各种类型标样或管理样品的分析对比表明,本法不仅适用于硅酸盐类岩石样品的分析,还适用于铁矿、铝土矿、碳酸盐类岩矿样品以及水泥、耐火材料等样品的分析。     

Isotopic systematics of He,Ar, S,Cu, Ni,Re, Os,Pb, U,Sm, Nd,Rb, Sr,Lu, and Hf in the rocks and ores of the Norilsk deposits

This paper reports the first results of a study of 11 isotope systems (³He/⁴He, ⁴⁰Ar/³⁶Ar, ³⁴S/³²S, ⁶⁵Cu/⁶³Cu, ⁶²Ni/⁶⁰Ni, ⁸⁷Sr/⁸⁶Sr, ¹⁴³Nd/¹⁴⁴Nd, ^206–208Pb/²⁰⁴Pb, Hf–Nd, U–Pb, and Re–Os) in the rocks and ores of the Cu–Ni–PGE deposits of the Norilsk ore district. Almost all the results were obtained at the Center of Isotopic Research of the Karpinskii All-Russia Research Institute of Geology. The use of a number of independent genetic isotopic signatures and comprehensive isotopic knowledge provided a methodic basis for the interpretation of approximately 5000 isotopic analyses of various elements. The presence of materials from two sources, crust and mantle, was detected in the composition of the rocks and ores. The contribution of the crustal source is especially significant in the paleofluids (gas–liquid microinclusions) of the ore-forming medium. Crustal solutions were probably a transport medium during ore formation. Air argon is dominant in the ores, which indicates a connection between the paleofluids and the atmosphere. This suggests intense groundwater circulation during the crystallization of ore minerals. The age of the rocks and ores of the Norilsk deposits was determined. The stage of orebody formation is restricted to a narrow age interval of 250 ± 10 Ma. An isotopic criterion was proposed for the ore-bearing potential of mafic intrusions in the Norilsk–Taimyr region. It includes several interrelated isotopic ratios of various elements: He, Ar, S, and others.     

Viscous, cohesive, non-Newtonian, depositing, radial slurry flow

Mining induced subsidence can significantly affect mining costs where major surface facilities and natural environment need to be protected. Overburden grout injection is a technology used to control coal mine subsidence by injecting the mine waste material extracted from the coal back into the inter-burden rock during longwall mining. The flowing slurry is here categorised as a nonlinear viscous cohesive (Bingham plastic) fluid. During longwall mining the grout slurry is pumped into the separated beds of the rock mass through a central vertical borehole, which is drilled deep into the inter-burden rock strata above the coal seam. However, a blockage can occur in the injection system when the slurry velocity falls below a certain critical threshold velocity, indicating a material phase change from cohesive-viscous to cohesive-frictional. In situ field injection tests through boreholes have been simulated at a smaller scale at the CSIRO laboratory in Brisbane by pumping the slurry through a radial disk (gap = 4 mm) from its centre. Laboratory experiments indicate a general, nonlinear, cohesive, viscous, frictional model for shear behaviour of the slurry, in which the material shear parameters are functions of the disk radial distance. Complete dimensional and dimensionless analytical solutions have been developed based on an approach related to Bingham–Herschel–Bulkley fluid mechanics. The derived formulae include relations for minimum pump pressure, local pressure and pressure gradient, wall shear stress, volume rate, velocity and velocity gradient. The theoretical results match the experimental measurements. The experiments covered slurries with maximum particle sizes of 0.5 to 2 mm with about 50% being larger than 100 µm. The viscosities at the various solids concentrations were measured with a standard torsion viscometer. This study differs from the previous research in several distinct aspects, namely, consideration of the variable shear parameters rather than fixed values, inclusion of total nonlinear behaviour, and implementation of a friction function to mimic behaviour of the deposited and consolidating stiff slurry, which can cause a significant pressure rise as a result of the increased shear resistance.     

硅酸盐中铁、锰、钛、钙、钾、磷、硅、铝、镁、钠、锶、铷、钡的X-射线荧光光谱定量测定

本文介绍样品经四硼酸锂熔融制成玻璃小饼。采用Lachance模式和理论a系数来校正元素间的效应,由3080E型X-射线荧光谱仪和DF-350B数据处理系统完成硅酸盐中十三个项目的测定。     

Bellechester,Minnesota, USA,lagoon collapses

Bellechester, Minnesota, is a small community of approximately 155 residents located on the county line between Goodhue and Wabasha counties in southeast Minnesota's karst region. Bellechester is served by a 21-year-old wastewater treatment facility (WWTF) consisting of three waste-stabilization ponds. On 28 April 1992 six sinkholes were discovered to have drained cell 2 of the WWTF resulting in the loss of approximately 8.7×10⁶ 1 of partially treated effluent and about 600 m³ of soil into previously undetected subsurface voids of unknown dimensions. In the week following the collapse, approximately 200 water wells located within a 5-km radius of the WWTF were sampled in an after-the-fact, emergency sampling program. Twelve samples with elevated fecal coliform levels, 18 samples with nitrate-nitrogen greater than the 10 mg/1 standard, and no samples with elevated chlorides were found. However, the elevated levels could not be unambiguously attributed to the WWTF collapse. This is the third WWTF to fail by sinkhole collapse in southeast Minnesota since 1974. All three collapsed lagoons have been located in similar geomorphic and stratigraphic settings. However, at least two lagoons have collapsed in the adjacent area in northeast Iowa, and these lagoons are located at different stratigraphic positions. Twenty-two WWTFs constructed in southeast Minnesota's karst region in the last 25 years have been identified as subject to potential sinkhole collapse. An unknown but significant number of manure storage lagoons, flood control structures, etc., have also been constructed in the karst region and are at risk. Public agencies are beginning to develop plans to deal with the risk associated with existing and future waste lagoons in this environment. The critical hydrogeologic parameters that can be used to prioritize the risk of collapse at existing facilities include: (1) the lithology of the first bedrock beneath each lagoon, (2) the thickness of surficial materials between the lagoon and the bedrock surface, (3) the presence and construction of liners (seepage rate), and (4) the proximity to existing sinkholes.     

Mercury,arsenic, antimony,and selenium contents of sediment from the Kuskokwim River,Bethel, Alaska,USA

The Kuskokwim River at Bethel, Alaska, drains a major mercury-antimony metallogenic province in its upper reaches and tributaries. Bethel (population 4000) is situated on the Kuskokwim floodplain and also draws its water supply from wells located in river-deposited sediment. A boring through overbank and floodplain sediment has provided material to establish a baseline datum for sediment-hosted heavy metals. Mercury (total), arsenic, antimony, and selenium contents were determined; aluminum was also determined and used as normalizing factor. The contents of the heavy metals were relatively constant with depth and do not reflect any potential enrichment from upstream contaminant sources.     

滇东南花岗岩与锡、银、铜、铅、锌多金属矿床的成因关系

滇东南锡、银、铅、锌多金属矿床主要分布在个旧、白牛厂、都龙3个矿区,而滇东南较大的3个花岗岩体又分别出露在3个矿区或附近.花岗岩体均形成于燕山晚期,岩石化学、矿物成分相似,富含锡、银、铅、锌、钨、铜等成矿元素.矿床主金属元素组合与岩体之间的距离由远而近出现由锡、钨、(铍、铌、钽)→锡、钨、(铁)、铜、铟→锡、铅、锌、银、铟、(锑)有规律的变化.花岗岩浆是成矿物质来源和成矿热源.岩浆侵入初期使上覆地层隆起产生背斜(凹陷部位成向斜);同时使地层产生一系列裂隙、压性断层或层间断裂;岩浆侵入晚期,这些断层再次活动,表现为张性,岩浆产生的含矿热液沿由其活动所造成的断裂迁移、充填、交代、沉淀而形成矿床.     

岩石密度和超高压岩石折返速率

在常温常压条件下对中国大陆科学钻CCSD主孔100-3000米岩心样品进行了密度测量,建立了密度连续剖面,并界定了不同超高压岩石的密度值。通过对比高温高压物性实验资料,岩石密度随着退变程度增强而降低,榴辉岩密度变化序列为3.52g/cm3→3.49g/cm3→3.07g/cm3→2.93g/cm3。超高压长英质岩石密度变化序列为3.00g/cm→2.80g/cm3→2.65g/cm3。上述实验资料是讨论不同折返阶段岩石所受浮力的基础,为研究折返速率大小提供了基本参数。本文通过折返板块运动平衡时,上浮力与粘滞力平衡这一关系式,定量研究了大陆俯冲板块的折返速率,认为密度差产生上浮力从而引起折返,温度对板块折返速率的影响最为显著;密度差大小、折返角度、折返板块大小对折返速率也有直接的影响。定量模拟分析表明,在温度高于850℃时,板块的折返速率可以超过100mm/a;当温度降至700℃时,折返速率则低于1.5mm/a。作者认为在折返早期,温度较高,板块快速折返至60-70km榴辉岩相深度;随着传导散热,温度降低,板块以较慢的速率折返至中下地壳。折返速率的估算表明,浮力是板块折返第一阶段(从>100km深部折返至<40km的中下地壳)的主要驱动力。