涌浪作用下港内大型集装箱船运动特性数值研究

随着船舶大型化和港口建设深水化发展,外海不同周期波浪作用下大型系泊船泊稳问题与小型系泊船相比出现了新的特点。为此,利用数值模型方法研究了在不同入射角度和周期的涌浪作用下港内大型系泊船的水动力响应,针对系泊船的泊稳情况探讨了船舶的运动规律和运动特性。研究发现,在涌浪周期较大的情况下,限定波高的泊稳标准不足以用来确定系泊船的正常作业条件,港内泊船的水平运动（纵荡、横荡和艏摇）极易超出运动标准值并影响装卸作业效率,并且船舶的水平运动表现出主要由次重力波主导的低频运动特性,而垂直运动（垂荡、横摇和纵摇）表现出主要由短波主导的波频运动特性。     

FSRU码头系泊模型实验与数值模拟研究

FSRU在恶劣环境条件下的作业和安全停靠性能与系泊缆张力、靠垫挤压应力、船体6自由度运动等参数有关。针对FSRU码头处海洋环境条件,进行FSRU不同装载状况的模型实验,获得FSRU的6自由度运动及其系泊载荷的动力特性。基于三维辐射和绕射理论,使用Sesam软件进行频域计算,以此为基础在相应海洋环境条件下进行时域耦合分析,获得FSRU 6自由度运动、系泊载荷、靠垫应力等参数的响应时历。结果表明:30%装载、横浪条件下FSRU的运动响应最大,系泊缆张力未达到破断值,靠垫压力超过其压缩60%时的载荷;模型实验对FSRU运动响应和系泊缆张力的预测结果可信,靠垫受力情况需要数值仿真进行辅助研究。     

峡道地区深水港超大型船舶靠系泊研究—以算山码头1^#泊位为例

本文对中国石化总公司镇海炼化公司算山码头１＾＃泊位进行了我国首例以水流作用为主的１５－２５万ｔ级超大型油轮的靠系研究。研究重点为靠泊方式，靠泊时的附加水体质量，靠泊时间的择优，靠泊速度、水流对系泊在码头船的斜向推开力，取得与实践相符的成果，并已为日常作业所采用。     

TLP平台码头系泊运动响应及缆绳张力研究

张力腿平台(Tension Leg Platform,TLP)码头舾装时需要采用临时多点系泊方法实现码头系泊,又因TLP平台立柱高度大、系缆布置不同于传统平台,有必要对其码头系泊运动响应和缆绳张力进行深入研究,以确保TLP平台在码头舾装期间,能够抵抗一定程度的不利气象条件。采用AQWA软件建立TLP平台码头系泊模型,同时模拟了码头靠垫以及浮箱靠垫,根据外高桥附近的气象、水文条件,通过计算,研究不规则波作用下的平台运动响应及缆绳张力,并分析两者在向岸、离岸环境载荷下的变化规律。本研究对TLP平台码头安全系泊设计具有重要的参考意义,为国内船厂TLP平台建造及码头舾装提供了重要理论依据和技术指导。     

远海浮式结构物与供应船旁靠系泊特性研究

针对远海浮式结构物与供应船进行旁靠作业时,水动力干扰、两船的相对运动、旁靠系缆系统和护舷系统的受力特征等问题开展研究。建立各船的有限元模型,设计出两船旁靠连接缆系统,选取合适的系泊缆和护舷参数。研究表明:浮式结构物和供应船的横荡、纵荡方向存在一定的同步性或跟随性,幅值相差不大,其它方向的运动并不存在明显的同步特征;供应船的各自由度运动幅值均比浮式结构物偏大;旁靠护舷的受力时历出现了明显的低频效应,说明护舷的受力较大程度上受船体低频慢漂运动的影响;浮式结构物对供应船的水动力干扰较大,当浮式结构物在供应船的上风位置时,表现为屏蔽效应,供应船的运动较小;在其背风位置时,运动加剧,出现多次共振、峰值放大现象,供应船对浮式结构物的水动力性能几乎无影响,因此,供应船从浮式结构物的下风口一侧靠泊作业将更有利于船舶的安全性能。这些研究结论可为实际工程操作提供参考。     

人工岛游艇码头泊稳试验与数值模拟研究

针对青岛万达游艇码头项目进行了港域波浪物理模型试验研究。试验表明,当口门处人工岛护岸采用直立式结构时,港池入口处波浪反射严重,港内波高较大,各码头泊位不满足泊稳要求;当采用斜坡式结构时,港内波高显著减小,游艇码头泊位满足泊稳要求,工作船泊位不满足泊稳要求,其最大波高比允许值仅大0.1m。采用MIKE21BW模型,考虑波浪的折射、绕射、反射及破碎等物理过程,对港域的波浪传播变形过程进行数值模拟,计算得到了港域的波浪分布状况,将计算结果与试验结果进行比较,吻合良好,表明该模型可用于近岸波浪的传播变形模拟及港域泊稳计算,计算结果可用于游艇码头结构设计。     

MOSES软件在系泊浮体运动计算中的应用研究

采用MOSES软件计算某起重船迎浪下的水动力性能和运动响应,并对该船进行缩尺比为1:50的模型试验。通过软件计算结果和试验结果的对比,分析计算模型的网格划分、二阶波浪力计算方法和粘性阻尼等关键参数的选取对MOSES计算系泊浮体运动的影响,为MOSES软件在系泊下运动计算方面提出建议。     

法向承力锚拖曳安装过程的整体模拟

法向承力锚(Vertically Loaded Plate Anchor,VLA)是一种适用于深水的新型系泊基础,它的拖曳安装过程直接决定了其系泊定位的精度和锚体的最终承载能力。综合考虑VLA锚体、锚泊线和上部船体的运动,建立了一种新的准静力整体分析模型。模型包括不断贯入海床的锚体、锚泊线(土中反悬链段和水中悬链段)和安装船体三部分,针对确定的锚泊线长度,安装船运动张紧锚泊线进行安装的过程,计算了此过程中锚体的运动轨迹、锚泊线形态和作用在船体上的锚泊线张力矢量的变化,重点分析了不同抛链长度和海床土体的参数对安装过程控制的影响,发现链长与水深之比达到5时,接近极限贯入深度。     

系泊船非线性波浪力时域计算:二维模型

为找到具有工程实用价值的港口系泊船波浪力的时域计算方法,建立了在港口中存在系泊船时非线性波浪力时域计算的垂直二维耦合模型:用Boussinesq方程计算船的两侧的外域,用欧拉方程计算船底面下的内域,两域在交界面处的连接条件是流量连续和压力相等.将复平面内的边界元方法应用于所研究问题,对耦合模型进行了验证.进行了相关模型实验,实验结果与数值计算结果比较表明这两种数值计算模型都具有满意的精度,但耦合模型的计算效率要远远高于边界元方法的计算效率.本耦合模型的数学处理简单,可适用于工程计算.     

关于研制防风短索的设想

关于研制防风短索的设想姚宗州，尚永春（海军后勤学院）海军舰船在完成作战任务和训练任务后，一般停靠在军用码头，在军港的特有防风条件和系泊索的协助下，躲避一般风浪对舰船的冲击，而在大风浪条件下，为了避免船与船，船与码头之间的冲撞，需在锚地防风。锚地没有军...     

Cause and countermeasure of long-period oscillations of moored ships and the quantification of surge and heave amplitudes

Long-period oscillations of moored ships whose periods are about 1 or 2 min cause many troubles in many ports and harbours. It is necessary to investigate these phenomena and verify their causes and countermeasures in each case because they are strongly dependent on the environment of each port and harbour. From this point of view, long-period oscillations of moored ships in the Port of Shibushi in Japan were investigated by means of wave observations, the image processing of moored ship motions using the video camera and motion-capture software and numerical simulations. From observation results, the relationship between offshore long-period waves and long-period oscillations of moored ships was recognized and surge and heave amplitudes were quantified by using wave data in order to forecast moored ship motions. Furthermore, from observation and numerical results, it was revealed that long-period waves with the peak period of 120 s from the offshore typhoon kept or exaggerated the local harbour oscillation of 60–70 s and it caused long-period oscillations of moored ships. Numerical results in case of reducing the reflection coefficient of the target berth implied that it ceased the local harbour oscillation and it would give an effective countermeasure to reduce long-period oscillations of moored ships in the Port of Shibushi.     

Initial attack of large-scaled tsunami on ship motions and mooring loads

In this paper, we propose a numerical simulation procedure of moored ship motions due to initial attack of large-scaled tsunamis and investigate the effects on the motions and mooring loads. The effect of methodology on selection of tsunami wave components and of the drag forces are then considered by using the numerical simulation method, applying to several case studies for LNG-carrier. Large ship motions and excessive mooring loads beyond the safe working loads are induced by the resonant tsunami wave components in the sway and surge motions and drag forces.     

The dynamics of wave induced ship motions in shallow water

The analytical method developed by Svendsen (1968) for a forced heave motion is extended to the general problem of wave induced heave, roll and sway motions of a long ship at a depth of water which is only slightly larger than the draught of the ship. This corresponds, for example, to the situation of a fully loaded ship in a harbour area.After linearization of the problem, the water motion is considered for each of the three individual motions and for the wave reflection-transmission problem for a fixed ship. The ensuing results for the forces on the ship are then synthesized to form the equations of motion, which are presented with all coefficients given, including mooring forces.Analytical and numerical results are given for the three components of motion, for the associated resonance frequencies, and for the hydrodynamic masses and moments of inertia. Finally, the assumptions used are analyzed and evaluated by comparison with measurements and with other results for a special case.     

风浪流联合作用下单点系泊船的受力分析

研究了风浪流联合作用下单点系泊船的受力问题.在应用Newman公式计算波浪漂移力的基础上,结合文献《Fleet Moorings Design Manual》,提出了不同方向的风、浪、流联合作用时,单点系泊船所受到的横向力、纵向力和回转力矩的计算方法.提出了风浪同向时,不同风流夹角组合对应的船舶平衡位置的确定方法.为缆绳、锚的选择以及舵角的控制提供了依据.最后通过算例验证了本方法的适用性和实用性.     

Experimental studies on the slowly varying drift motion of a berthed container ship model

The effects of free-surface waves on the floating structures are of great importance in the offshore industry. Among the six degrees of motions of a surface ship the absence of restoring forces in surge, sway and yaw led to critical situations for moored ships in the recent times. The order of forces in horizontal plane and their exciting frequencies are matters of interest. The resonance with the presence of moored chains led to many accidents in the recent past. The lines in dry conditions may not give good damping and in wet condition they may trigger the system to chaotic motions and jumps. Two different loading conditions of a container ship model are tested with waves in laboratory conditions in two different drafts. The mooring lines are chosen as per scale law and the energy under the response spectrum is determined from the plots. The results give new insights into the movement of a berthed ships subjected to waves. Response of the moored ship to different loading conditions in different water depths are discussed in this paper. The paper gives the order of energy due to first-order and slowly varying movement of a berthed container model in a towing tank.     

Experimental and Numerical Investigations of Ship Parametric Rolling in Regular Head Waves

Parametric rolling is one of five types of the ship stability failure modes as proposed by IMO. The periodic change of the metacentric height is often considered as the internal cause of this phenomenon. Parametric rolling is a complex nonlinear hydrodynamic problem, often accompanied by large amplitude vertical motions of ships. In recent years,the Reynolds-averaged Navier–Stokes(RANS) equation simulations for viscous flows have made great progress in the field of ship seakeeping. In this paper, the parametric rolling for the C11 containership in regular waves is studied both experimentally and numerically. In the experiments, parametric rolling amplitudes at different drafts, forward speeds and wave steepnesses are analyzed. The differences in the steady amplitudes of parametric rolling are observed for two drafts. The effect of the incident wave steepness(or wave amplitude) is also studied, and this supports previous results obtained on limits of the stability for parametric rolling. In numerical simulations, the ship motions of parametric rolling are analyzed by use of the potential-flow and viscous-flow methods. In the viscousflow method, the Reynolds-averaged Navier–Stokes equations are solved using the overset grid method. The numerical accuracies of the two methods at different wave steepnesses are also discussed.     

A Time-Domain Coupled Model for Nonlinear Wave Forces on A Fixed Box-Shaped Ship in A Harbor

A 2-D time-domain numerical coupled model is developed to obtain an efficient method for nonlinear wave forces on a fixed box-shaped ship in a harbor.The domain is divided into an inner domain and an outer domain.The inner domain is the area beneath the ship and the flow is described by the simplified Euler equations.The other area is the outer domain and the flow is defined by the higher-order Boussinesq equations in order to consider the nonlinearity of the wave motions.Along the interface boundaries between the inner domain and the outer domain,the volume flux is assumed to be continuous and the wave pressures are equal.Relevant physical experiment is conducted to validate the present model.It is shown that the numerical results agree with the experimental data.Compared with the coupled model with the flow in the inner domain governed by the Laplace equation,the present coupled model is more efficient and its solution procedure is more simple,which is particularly useful for the study on the effect of the nonlinear wave forces on a fixed box-shaped ship in a large harbor.     

Wash Waves Generated by High Speed Displacement Ships

It is difficult to compute far-field waves in a relative large area by using one wave generation model when a large calculation domain is needed because of large dimensions of the waterway and long distance of the required computing points. Variation of waterway bathymetry and nonlinearity in the far field cannot be included in a ship fixed process either. A coupled method combining a wave generation model and wave propagation model is then used in this paper to simulate the wash waves generated by the passing ship. A NURBS-based higher order panel method is adopted as the stationary wave generation model; a wave spectrum method and Boussinesq-type equation wave model are used as the wave propagation model for the constant water depth condition and variable water depth condition, respectively. The waves calculated by the NURBS-based higher order panel method in the near field are used as the input for the wave spectrum method and the Boussinesq-type equation wave model to obtain the far-field waves. With this approach it is possible to simulate the ship wash waves including the effects of water depth and waterway bathymetry. Parts of the calculated results are validated experimentally, and the agreement is demonstrated. The effects of ship wash waves on the moored ship are discussed by using a diffraction theory method. The results indicate that the prediction of the ship induced waves by coupling models is feasible.