卷破波作用下沙质岸滩剖面形态判别式初探

通过波浪水槽实验,开展不同类型波浪作用下的沙质岸滩演化规律研究工作。本次实验研究不考虑比尺,采用1:10与1:20组成的复合沙质斜坡对岸滩进行概化,选取规则波和椭圆余弦波两种典型波浪作用,对波浪的传播、变形和破碎、上爬、回落过程以及波浪作用前后沙质岸滩床面地形进行了观测,探讨波浪作用下沙质岸滩剖面演化规律。本文实验工况中,规则波作用下,岸滩剖面呈现出沙坝剖面和滩肩剖面,椭圆余弦波作用下的岸滩剖面均呈滩肩形态,发现岸滩剖面形态不仅与波浪作用类型、强度、周期等因素相关,还与波浪破碎的强度等因素有关。通过对实验过程中现象的进行观察和分析,引入了卷破波水舌冲击角的概念。对波浪卷破破碎后形成的水流挟沙运动与岸滩剖面形态的关系进行定性分析,对水舌冲击角与Irribarren参数之间的关系进行定量分析,基于Irribarren参数与岸滩剖面形态的关系初步建立了波浪作用下沙质岸滩剖面形态判别关系式。通过本文实验结果和前人实验结果对趋势线进行拟合,求得其判别系数,判别式能够较好地划分淤积型岸滩、侵蚀型岸滩及过渡型岸滩三种岸滩形态。     

波浪动力因素变化对沙质岸滩演变的影响

通过波浪水槽实验,对海平面变化造成的波浪动力因素改变引起的沙质岸滩形态响应开展机理性研究。实验采用1∶10单一沙质斜坡概化岸滩,利用3种不同实验水深模拟海平面变化,考虑椭圆余弦波、非规则波、规则波和孤立波4种类型波浪作用。实验对波浪在斜坡上的传播变形、破碎、上爬和回落过程的波高及波浪作用后的岸滩地形进行了测量。实验结果表明,椭圆余弦波、规则波和非规则波作用下,平衡岸滩呈现出滩肩形态,孤立波作用下则呈沙坝形态。海平面上升造成波浪动力增强,沙质岸滩平衡剖面形状基本保持不变向岸平移,槽谷、滩肩、沙坝位置以及岸线蚀退距离,均呈现出良好规律性。     

红树林对规则波作用下岸滩剖面变化影响实验研究

红树林广泛分布于我国南方沿海地区,可有效减小波浪对岸滩的破坏,研究其在规则波作用下对岸滩变化的影响具有重要意义。基于波浪水槽实验,采用PVC圆管模拟红树林,选取无黏性沙堆砌而成的1/10~1/20组合坡概化岸滩。实验结果表明,在规则波作用下,红树林的存在对岸滩剖面变化产生了较大影响;并分析了规则波波陡、植物分布密度和排列方式对岸滩剖面变化的影响。基于实验数据,建立了在实验条件下的岸滩冲刷坑尺度、淤积沙坝尺度、最大冲刷深度、最大淤积高度与规则波波陡、红树林的分布密度和排列方式之间的关系式,结果呈幂指数函数关系。揭示了岸滩剖面变化与规则波水动力特性、红树林、泥沙颗粒和岸滩坡度之间的联系。引入植物综合系数,预测给定规则波波陡和波长情况下的岸滩冲淤演变特征值,为海岸生物防护工程的建设提供科学依据。     

风暴浪作用下沙质岸滩稳定机制物理模型试验研究

近年来风暴潮等海洋灾害日趋频发,沙质海岸侵蚀问题也愈发突出,沙滩稳定防护显得日益重要。为研究风暴浪作用下沙质岸滩稳定机制问题,设计了一系列的水槽试验,对风暴浪作用下沙质岸滩的稳定机制和演变过程进行了录像观察和研究分析。试验中采用图像处理技术,根据水和岸滩床面的像素值差异,对岸滩整体剖面进行实时动态提取;对比和分析了不同入射波高、波周期、水深、岸滩初始坡度以及波高连续变化下沙质岸滩演变过程。试验结果表明,岸滩稳定与岸滩初始坡度和沙坝的发育直接相关,而波参数主要影响岸滩扰动幅度和沙坝以及前滩侵蚀边界的位置变化。当入射波高连续变化时,沙坝迅速响应并向离岸迁移。岸滩变化幅值与入射波能流存在明显正相关关系,波能流越大对岸滩稳定性的危害越大。而水位升高会增强前滩向岸侵蚀风险。此外,在本试验尺度下,前滩以侵蚀为主。当岸滩初始坡度小于稳定坡度且波陡较小时,即Dean参数Ω''较小时,岸滩才发生明显的前滩淤积,这对于试验尺度下岸滩恢复工况研究至关重要。具体来说,当岸滩整体坡度为1:10且前滩坡度达到1:5~1:2.5时,岸滩稳定性最好,岸滩形态最接近最终平衡剖面,岸滩趋于稳定的时间最短。     

人工岛对沙质海岸动力泥沙环境及岸滩冲淤演变的影响研究

基于历史海图、历史时期卫星遥感影像、2019年实测水下地形和潮流、波浪数值模拟成果,研究该海域岸滩的发育演变背景、海床和岸线自然冲淤动态、动力泥沙环境及岸滩冲淤动力机制。采用LITLINE岸线演变数学模型,模拟计算了不同离岸距离和不同平面形态人工岛布置型式对近岸岸线变形的影响,岸滩泥沙动力机制和岸滩演变趋势表明,人工岛实施后近岸最大潮流流速小于近岸泥沙起动流速,不具备起动近岸岸滩泥沙的基本条件; SSE向波浪作用时,人工岛西北侧波高明显减弱,波向西偏; S向波浪作用时,人工岛北侧波高明显减弱; SSW向波浪作用时,人工岛东北侧波高明显减弱,波浪传播方向东偏;波浪场改变后人工岛掩护区东西两侧岸滩附近泥沙分别具有向东和向西运移至人工岛掩护区的趋势,形成掩护区的淤积和东西两侧岸线冲刷。     

孤立波对礁坪上直墙冲击试验和RANS数值模拟

在有、无礁冠两种典型岛礁剖面地形上开展孤立波冲击礁坪上直墙的二维水槽试验和数值模拟研究。通过OpenFOAM结合k-ε湍流模型进行RANS数值模拟,基于试验数据和验证后的RANS模拟结果,研究了岛礁剖面上孤立波传播的水动力特性及其对直墙的作用,并探讨了礁冠的存在对直墙所受冲击的影响。结果表明:RANS(k-ε)模型能够准确还原孤立波在岛礁地形上的主要传播特征,但在波浪破碎的情况下,RANS数值模拟不够精细,尤其对直墙所受瞬击荷载的捕捉能力欠缺;礁冠的存在,增强了波浪反射,使得波浪提前破碎,减小了直墙上的波浪爬升和最大动压。     

风压作用下非线性极端波浪的数值模拟

本文在时域非线性数值波浪水槽中，研究了不同风速条件下极端波浪的特性。采用推板造波的方式生成非线性波浪，基于Jeffrey遮蔽理论将风压项引入自由面动力学边界条件来模拟风压作用，通过高阶边界元法和混合欧拉-拉格朗日时间步进法来求解初边值问题。通过与已发表的聚焦波群实验结果对比验证了该数值模型的准确性，并研究了风压对极端波浪的最大波高、聚焦位置的偏移和波浪谱的演变等波浪性质的影响。本文进一步在数值波浪水槽中引入均匀水流，来模拟风生流对波浪演变的影响。结果表明，风压的存在会少量增大极端波浪的最大波高，波浪的聚焦和解焦过程伴随着明显的能量传递，并且风生流进一步导致了波浪聚焦位置的偏移。     

珊瑚岸礁破碎带附近波浪演化实验研究

通过波浪水槽实验对珊瑚岸礁破碎带附近波浪演变规律开展研究,实验采用了概化的岸礁模型,测试了4种礁坪水深、4种礁前斜坡坡度和一系列入射波高的组合工况。对破碎带宽度和破碎带附近波浪的入射、反射、透射以及能量耗散进行了测量分析,透射波的计算考虑了礁坪上高次谐波的影响。结果表明:礁坪水深和入射深水波高的比值(即礁坪相对水深)是影响岸礁破碎带附近波浪演化的关键参数,而礁前斜坡坡度的影响在本文测量的范围内可以忽略不计。破碎带宽度与礁坪上浅水波波长为同一数量级,并与礁坪相对水深成反比;透射系数随礁坪相对水深的增大呈线性增长,而反射系数的变化却无类似规律;岸礁能够削弱超过50%入射波能,礁坪相对水深越小,波浪破碎造成的能量耗散越大。     

砂质海岸突堤式建筑物下游岸线变形数学模型

提出了一种改进的砂质海岸岸滩演变的“一线理论”数学模型.该模型中考虑了岸滩演变过程中岸滩坡度变化的影响,并采用波浪折射、绕射和反射联合计算数学模型模拟掩护区的波浪场,提高了波浪计算的精度.实例计算表明,在验证资料比较充分的条件下,该数学模型计算结果的可靠度较高,可供实际工程规划和设计时参考使用.     

近岸区直墙波浪力的模拟

在水槽中进行了几种不同坡度的斜坡平台上规则波作用下直墙波浪力试验，系统分析了直墙上相对最大压强和相对最大总力，给出了它们之间的比较关系。还进行了不同坡度的不规则波模型试验，并讨论了波浪力之间的特性。结果表明采用1：10、1：15的斜坡与平台相结合的试验室模拟，可得到与平底地形相近的直墙波浪力。     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,