燃烧加热污染空气对超燃冲压发动机性能影响研究

针对燃烧加热地面试验设备存在的工质污染问题,采用数值模拟方法研究了燃烧加热污染空气对氢燃料超燃冲压发动机性能的影响。以飞行马赫数Ma=6.5,当量油气比ER=0.6为计算基准状态,分别对纯净空气和污染空气来流下氢燃料超燃冲压发动机的整机流场和性能进行了对比计算分析。燃烧化学反应模拟采用了改进的H₂/O₂七组分八方程模型,湍流模型为标准的 k-ε模型,并采用直连式燃烧室试验数据进行了数值方法的验证。研究结果表明:(1)相对于纯净空气来流,污染空气来流下的超燃冲压发动机推力和比冲均有所下降。(2)采用酒精燃烧加热器的前提下,来流参数匹配静温、静压、马赫数时,发动机性能与纯净空气来流下的结果最为接近,而匹配总温、总压、马赫数时相差最大。(3)来流参数匹配总焓、静压、马赫数的前提下,采用氢燃烧加热器时发动机性能与纯净空气来流下的结果最为接近,而采用甲烷燃烧加热器时相差最大。      

基于统计建模的P2P IPTV流测量研究

近年来对P2P网络电视流量及其行为特征进行测量已成为1个重要的研究领域。但当前的P2P流测量研究主要侧重于P2P文件共享系统,对于P2P网络电视的研究则偏重于对某单一应用的分析。文中针对以上问题从流到达的间隔时间与流到达率两方面,对当前最流行的4种P2P流媒体软件进行基于统计建模的流测量研究。结果表明:P2P网络电视的实时性要求以及用户行为的相似性使各种P2P流媒体流量具有相似的流量模型且具有重尾特征。     

水下圆形截面缆索的流体动力性能的理论计算及试验研究

本文对锚索及水下拖索的阻力、性状及其计算问题进行了初步的探讨,得出了计算均流中圆形截面揽索的阻力、阻力系数、张力以及缆索形状的公式,并根据这些公式编制了计算机程序,同时运用此程序对水下拖索的实例进行了计算。另外,对各种不同流态、不同倾角下的圆形截面缆索、带整流扳缆索以及流线型截面缆索做了风洞试验,并将试验所得的阻力系数与本文导出的理论公式计算所得的阻力系数进行了比较,结果两者符合较好。     

基于最小二乘法的超短基线水声定位系统校准方法

超短基线水声定位系统是海洋工程及水下无人系统中应用较广泛的精密仪器设备，为了提高对水下目标的定位精度，在使用前需对其进行校准。描述了一种基于最小二乘法迭代修正的超短基线水声定位系统校准方法，该方法以最小二乘法为基本原理，通过多次迭代修正的方式，修正基阵与GPS天线之间的平移偏差以及基阵与罗经之间的旋转偏差，从而提高系统的测量精度，最终通过湖上试验验证了该方法的有效性。     

海翼水下滑翔机测流应用

水下滑翔机其通过集成生物、化学、物理传感器可以测量如温度、盐度、溶解氧等多种海洋基础水文要素,其利用卫星定位系统获得实际出水速度和理论出水模型获得理论出水速度之差可以计算深度平均流,。本文利用海翼水下滑翔机获得温盐场及卫星定位数据评估深度平均流,结果显示利用温盐场获得深度平均地转流与水下滑翔机获得深度平均流相关系数0.95,表明其流场的一致性,同时根据船载观测ADCP误差分析法估算深度平均流误差约为0.036 m/s。借助深度平均流可以估算绝对地转流,包括正压地转流和斜压地转流。在零动力面的假设下,我们选取了海翼号水下滑翔机在南海的一组实验对流量误差进行了评估。该实验为2019年1月3日-2月16日海翼号水下滑翔机自南向北穿越西沙群岛附近一个中尺度涡观测。观测结果表明,该中尺度涡为冷涡流核,在涡心以南,绝对地转流为东向流,最大流速约为0.48 m/s;涡心以北,绝对地转流为西向流,最大流速约为0.47 m/s,稍弱于南侧。受不均匀时空观测计划影响,本文未对流量做出估计。     

HY-2卫星雷达高度计时标偏差估算

卫星雷达高度计是海洋遥感监测的重要传感器之一,测高系统和定轨系统是高度计重要的组成部分。若两系统使用不同的系统时钟,则获得的轨道高度和卫星测距值之间可能会存在一个时标偏差,该时标偏差会降低卫星雷达高度计的海面高度测量精度。针对HY-2卫星雷达高度计的时标偏差问题,本文分析了时标偏差对测高精度的影响,介绍了一种使用自交叉点数据估算时标偏差值的方法,并基于HY-2卫星雷达高度计第21个周期数据开展了时标偏差修正实验。时标偏差修正后HY-2自交叉点的海面高度差值(也称"不符值")分布收敛程度有了明显的提高,其RMS均方根值从24.7 cm减小到了7.0 cm,HY-2与Jason-2互交叉点的不符值的RMS也从16.6 cm减小到了7.3 cm。这表明本文介绍的时标偏差修正方法可有效地提高HY-2卫星雷达高度计的测高精度。     

北太平洋西边界流的低频变化特征

基于日本气象厅长时间序列的温、盐度再分析资料,利用动力计算方法分析了北太平洋西边界的北赤道流及其下游黑潮和棉兰老流流量的年际和年代际变化,并探讨了北赤道流变化的可能原因。结果表明,北赤道流和黑潮具有比较一致的年际和年代际变化,均在1976年前后发生了一次气候跃变,之后有长期偏强的趋势,而棉兰老流的年际和年代际变化则有所不同。特别是,北赤道流1976年之后增加的流量似乎大多进入黑潮,而流入棉兰老流的流量则减少。进一步的分析还表明,西传的Rossby波和棉兰老冷涡的变动可能对北赤道流的年际变化有重要影响。     

基于船舶空气流场仿真的船舶测风偏差校正方法

船舶海面风观测易受船体和上层建筑造成的畸变气流影响,使测风数据存在偏差。针对船舶相对风测量偏差校正问题,采用CFD仿真方法研究船体周围钝体绕流气流场,量化桅杆左、右横桁实测相对风速、风向与舰桥上部参考测风点相对风速、风向偏差,利用最小二乘支持向量机分别对左、右舷测风偏差进行回归并建立校正模型。通过海上实船实验采集桅杆左、右横桁与舰桥上部测风点处的相对风测量数据,验证模型校正测风偏差的实际效果,结果表明CFD仿真建模方法能够有效降低实验船型56%的相对风速测量偏差。     

沿岸流中混合系数的实验研究

进行了在规则波作用下破波带内水平混合系数测量的物理模型实验。通过在沿岸流流场中投放墨水点源和采用CCD摄像机摄像,测量了点源扩散过程。利用水深平均二维扩散方程近似解析解得到了由实验结果计算混合系数的方法。实验结果表明:扩散系数仅依赖于当地水深,与波浪参数(周期和波高)无关。沿岸流沿水深变化产生的离散作用导致顺流方向(纵向)混合系数远大于横流方向(横向)混合系数。横流方向混合系数中由波浪产生的扩散系数占总扩散系数约40%,其余为波浪破碎引起的湍流产生的扩散系数。     

1993年冬季所罗门群岛─关岛断面地转流的初步分析

根据1993年1─2月“实验3”号考察船在霍尼亚拉港（瓜达尔卡纳尔岛）至关岛的断面观测的温、盐度资料，分析了该断面上的地转流结构，计算了南赤道流及北赤道逆流的地转流流速和流量。结果表明：在纬线方向上E向流与W向流呈带状分布，在垂向上也多为E向流与W向流交替出现。在南赤道流和北赤道逆流中都夹有与主流向相反的流动，它们的流量分别约占主流向流量的1／3和1／5。文章还将分析计算结果与手头掌握的文献报道的结果作了比较。     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,