固定化海藻吸附金属离子的影响因素

研究了固定化海带吸附含铜、镉溶液过程的影响因素,结果表明,在pH为3.0~5.0时对Cu2+保持高的吸附率,在pH为4.0时对Cd2+的吸附率达到最大.随着Cu2+,Cd2+金属离子初始浓度的降低,吸附率有所降低.对Cd2+的吸附率均随着温度的升高而变大.随着吸附剂浓度的增大,对Cu2+,Cd2+的吸附率逐渐升高,与此相反,对Cu2+,Cd2+的吸附量则逐渐减小.粒径对Cu2+的吸附率影响较小,对Cd2+的吸附率有较明显的变化.     

固定化海带粉吸附剂对污水中3种重金属离子吸附的模拟研究

为了探讨海带粉吸附剂工业运用的可能性,采用海藻酸钙包埋法对海带粉进行固定,在合适的反应条件下对Ni2+、Cu2、pb2+三种重金属离子进行吸附.采用二级动力学方程、Langmuir方程和Freundlich方程对吸附过程进行模拟.结果显示二级动力学方程能很好地对固定化海带粉吸附剂吸附Ni2+、Cu2+、pb2+过程进行拟合,平衡时的吸附量分别达到0.317 4、0.465 9、0.501 5 mg/g,对应的二级动力学常数为0.128、0.116、0.114 g/(mg·min),即三种离子的吸附速率Ni2+＞ Cu2+＞ Pb2+;Langmuir方程和Freundlich方程都能较好地模拟Ni2+、Cu2+、pb2+的吸附过程,根据Langmuir方程Ni2+、Cu2、pb2+的最大吸附量分别达到2.786、13.699、39.063 mg/g,即吸附效果pb2+＞Cu2+＞ Ni2+,该实验对日后开发海藻生物吸附剂并将其大量制成应用产品有一定的意义.     

活性污泥和颗粒污泥生物吸附废水中Pb~(2+)的对比研究

采用序批式实验,分别以活性污泥和颗粒污泥为吸附材料,考察接触时间、pH等因素对废水中Pb2+生物吸附效果的影响.结果表明,活性污泥和颗粒污泥对低浓度Pb2+(0～20 mg/L)能在30 min内达到吸附平衡,当Pb2+浓度在20～100 mg/L时,浓度越低,达到平衡时间越快,以被动吸附为主.在Pb2+低浓度条件下(0～20 mg/L),初始pH为4～5时,Pb2+的去除率达99%以上,且初始pH值是影响活性污泥和颗粒污泥生物吸附Pb2+的重要因素.活性污泥和颗粒污泥对Pb2+的生物吸附符合朗缪尔(Langmuir)方程,在pH为4及25 ℃下,活性污泥饱和吸附量为59.88 mg/g,颗粒污泥饱和吸附量为80.65 mg/g.因此,活性污泥和颗粒污泥可作为有效的生物吸附剂处理低浓度(0～20 mg/L)含铅废水,且颗粒污泥比活性污泥的生物吸附效果好.     

“MgO/AC”复合材料对水溶液中Cu~(2+)和Cr(Ⅵ)的吸附性能研究

用造纸草浆黑液和氯化镁为原料制得氧化镁/活性炭("MgO/AC")复合材料,分别测定了该复合材料对水溶液中Cu2+与Cr(Ⅵ)的脱除性能。Cu2+的吸附随pH值的升高而增大,pH=3时基本达到平衡;在实验考察的pH范围内(1~8),Cr(Ⅵ)的吸附呈单调递减趋势。动力学拟合结果表明,"MgO/AC"复合材料对Cu2+和Cr(Ⅵ)的吸附过程均符合伪二级动力学方程;两过程的吸附速率均随吸附温度的升高而增大,表现为吸热吸附;吸附活化能Ea分别为50.19,51.42 kJ.mol-1;"MgO/AC"复合材料对Cu2+的吸附优于对Cr(Ⅵ)的吸附。Cu2+在"MgO/AC"复合材料上的吸附过程用Langmuir模型描述更为合适,在293~323 K范围内,Cu2+的饱和吸附量为19.46~90.91 mg.g-1;Cr(Ⅵ)的吸附过程则更符合Freundlich模型。     

黄河口海域沉积物对重金属的吸附

以黄河口海域表层沉积物为研究对象,研究沉积物对重金属Cu、Pb的吸附特性,将沉积物筛分为4种粒级,探讨粒度、pH值、吸附时间和吸附剂初始浓度对重金属吸附的影响。结果表明:沉积物粒径越小,对重金属的吸附量越大;吸附平衡时间有所差异,但在1.5h均能达到吸附平衡;吸附量均随pH值升高而逐渐增加,但铜的吸附较铅的吸附速度快;铜的吸附量与吸附剂初始浓度呈线性关系,而铅的吸附量在初始浓度较低时变化明显,随初始浓度增加吸附量增加减小;沉积物对铜吸附等温线符合Langmuir型,铅吸附等温线符合Freundlich型,吸附类型存在差异。重金属在沉积物中的吸附规律研究为黄河口海域污染调查及治理提供了科学依据。     

极大螺旋藻富积重金属机理的研究

于1993年5月由南京大学藻类培养室提供极大螺旋藻藻种,用Zarrouk培养基培养后,用活藻体和甲醛杀死的藻体分别进行吸附实验;过滤出的藻体置于6×10－3g／L左右浓度的Co2+,Ni2+,Cu2+,Zn2+离子混合液中。结果显示,死、活藻体都具有相似的吸附能力,对Co2+,Ni2+,Zn2+的富积大于203倍,对Cu2+的富积大于185倍;用热水提取、DEAE-纤维素D-23柱和SephadexG－200柱纯化后,获得了纯细胞外壁多糖,其分子量为52kD。将该糖溶液盛在透析袋内,并置于4种离子混合液中进行吸附实验,结果显示,核糖对Co2+,Ni2+,Cu2+,Zn2+的富积倍数分别达1744,1644,1340,1750。藻体和多糖对Co2+,Ni2+,Zn2+的吸附都高于对Cu2+的吸附。比较藻体与多糖对4种离子的吸附结果可见,藻体对离子的吸附主要是多糖的作用;多糖的红外光谱显示,金属离子改变OH和CO－NH的吸收峰,表明这两种基团与金属离子发生了络合作用;对Cu2+的络合滴定测定表明,Cu2+与多糖的结合度为0．40。     

细基江蓠(Gracilaria tenuistipitata)对海水池塘养殖区Cu~(2+)生物修复的初步研究

随着海水养殖业迅速发展,食用海产品重金属(如Cu、Cd等)超标问题日益突出。作为提取藻胶原材料及海洋养殖动物饲料的细基江蓠,可以大规模生长在海水池塘养殖区,有望用于该水域重金属污染的生物修复。本实验通过研究细基江蓠(Gracilaria tenuistipitata)在5个不同Cu2+浓度梯度(0、0.05、0.2、0.8、2.0mg/L)环境下的自身生长状况,及其对Cu2+的吸收富集情况,初步探究了细基江蓠对海水池塘养殖区Cu2+的生物修复能力。实验结果显示细基江蓠对Cu2+有较强的耐受性和吸收富集能力,在0.8mg/L Cu2+浓度下细基江蓠既能保证正常生长,又能吸附水体中最大量的Cu2+。     

球等鞭金藻对5种金属离子的吸附作用研究

通过研究球等鞭金藻(Isochrysis galbana)不同生长过程中对5种重金属离子(Cd2+,Cu2+,Zn2+,Pb2+,Cr6+)的吸附作用,探讨了其生长与金属离子吸附的关系,同时比较了其对不同金属离子的吸附能力。结果表明:在生长初期,球等鞭金藻对重金属离子的吸附能力较强,而在对数生长期后吸附能力变弱,其对5种重金属离子的吸附能力依次为:Pb2+≈Cu2+Zn2+Cr6+Cd2+。     

重金属铜污染对石珊瑚生长影响的实验研究

分布于热带海洋的珊瑚礁是重要的生态学资源.受全球环境变化和人类活动的影响,珊瑚礁正处于退化之中,其中重金属污染是人类活动影响珊瑚礁的重要方面.国际上不少研究初步探索了珊瑚对一定浓度重金属的响应,我国类似的研究尚不多.本文通过72h的急性毒性测试,研究重金属Cu2+污染对6科7属石珊瑚的影响,以了解重金属污染对石珊瑚所造成的伤害和石珊瑚对Cu2+污染的生态反应.实验结果显示,随着Cu2+浓度的增加,与珊瑚共生的虫黄藻密度呈现先短暂上升而后持续下降的趋势,直致珊瑚白化;Cu2+污染对块状滨珊瑚毒性影响最大,在浓度超过40·7μg·L-1时即致其死亡.Cu2+污染胁迫下所有试验珊瑚的触手伸展活动都出现异常,显示Cu2+污染对珊瑚生存有明显的影响.     

汛期黄河下游悬浮颗粒物粒度分布及其对铜离子的模拟吸附研究

为跟踪2004年6月19日至7月13日实施的黄河第三次调水调沙工程,2004年7月21日于东营胜利黄河大桥站位采集水样。对黄河下游悬浮物浓度、粒度分布进行了分析。结果表明,当天本站位悬浮物质量浓度为1.43 g/L,悬浮颗粒物粒度在63μm以下部分累积分布占99.3%。作者模拟汛期黄河下游河水的悬浮物浓度、年平均水温及pH,研究悬浮物对重金属Cu2 的吸附规律,并探讨了悬浮物浓度及盐度对吸附的影响。Cu2 在水体中会由于水解、絮凝、沉淀、络和等损失一部分,在研究吸附时对此部分进行了扣除。水体悬浮颗粒物对重金属Cu2 的吸附等温线吸附符合Langmuir方程。随悬浮物浓度的增加,其对Cu2 的吸附容量增大,吸附量减小。悬浮物浓度、pH一定时,在盐度为0~5时,吸附量随盐度的升高而迅速降低,当盐度在5~25时,吸附量基本不变。     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,