山东荣成榴辉岩和石榴石橄榄岩的岩石学矿物化学及其成因

用电子探针分析了山东荣成榴辉岩和石榴石橄榄岩中的石榴石和单斜辉石的化学组成。利用石榴石成分—成因判别图解并结合矿物地质温度计估算结果,判断荣成榴辉岩和石榴石橄榄岩为地幔来源,部分榴辉岩经历了后期壳内角闪岩相退变质作用。最后讨论了它们的成因意义和动力学演化。     

江苏东海毛北榴辉岩的矿物化学及其成因问题

本文利用电子探针,分析了江苏东海毛北榴辉岩中的石榴石和单斜辉石的化学组成。利用矿物地质温度计,计算了毛北榴辉岩的成岩平衡温度。结合本区的大地构造环境,提出在早元古代末期,华北陆块曾发生向南的大型堆覆构造,苏北地区即为推覆体前缘。     

高温高压条件下榴辉岩的结晶实验研究

报道在1180℃,压力分别为2.0GPa、2.5GPa、3.0GPa和3.5GPa条件下榴辉岩结晶实验结果。研究表明,当压力超过2.5GPa时方有石榴石晶出,随着压力的增大,石榴石中镁铝榴石和钙铝榴石含量增加,铁铝榴石含量减少;随着压力的增大,单斜辉石中的TiO_2和CaO含量减少,Al_2O_3和Na_2O含量增加,单斜辉石中硬玉端员分子含量增加。实验表明,自然界中天然产出的榴辉岩成岩压力远大于3.5GPa。     

青岛仰口榴辉岩及其围岩的岩石地球化学特征和成因机制

青岛仰口地区保存了完整的从变辉长岩到榴辉岩的超高压变质岩石组合。地球化学特征表明,榴辉岩、变辉长岩和片麻岩属钙碱性系列,超基性岩属拉斑系列;CIPW标准矿物计算显示榴辉岩和变辉长岩中长石以钠长石为主,超基性岩主要标准矿物为橄榄石、紫苏辉石和锥辉石,片麻岩中出现标准矿物刚玉;榴辉岩、变辉长岩和片麻岩富集大离子亲石元素,亏损高场强元素,超基性岩的微量元素相对于N-MORB亏损;榴辉岩和变辉长岩轻稀土明显富集,配分型式与岛弧玄武岩相似,片麻岩具明显的Eu的负异常,配分型式与后造山A型花岗岩相似,超基性岩稀土总量较球粒陨石偏高,具强烈的Ce的负异常。微量元素比值及地球化学图解表明榴辉岩与变辉长岩的原岩为辉长岩,片麻岩的原岩为造山后A型花岗岩,原岩的岩浆源区位于下地壳,超基性岩的岩浆源区位于上地幔,原岩均形成于岛弧环境。     

山东荣成马草夼大理岩中的榴辉岩岩石地球化学特征及成因

山东荣成马草夼榴辉岩呈条带状或透镜状产出于大理岩中,对其进行了岩石学和地球化学研究。研究表明,其原岩可能为辉石质岩石,且经过了一定程度的分异作用,暗色矿物发生堆晶作用,在微量元素原始地幔标准化蛛网图中,Th明显的亏损,U强烈富集,Ce也呈微弱程度亏损,在稀土元素球粒陨石标准配分模式图中,呈左倾分布模式。岩石的原岩构造环境分析表明其接近板内构造环境,其原岩可能为结晶分异之后矿物堆晶作用形成的辉石质岩石。     

蓬莱新生代玄武岩中的单斜辉石巨晶及深源包体的矿物化学

利用电子探针分析蓬莱新生代玄武岩中的单斜辉石巨晶及尖晶石二辉橄榄岩包体中的主要造岩矿物(单斜辉石、斜方辉石、橄榄石和尖晶石)的化学组成。利用单斜辉石地质温压计和二辉石地质温度计计算了尖晶石二辉橄榄岩包体的平衡温度和压力,计算表明它们来自于上地幔的不同深度,同时推测本区上地幔内存在化学组成的分带性。     

冷、暖俯冲变质作用的地震结果:以日本西南部和东北部为例

在俯冲作用期间 ,洋壳中易变的含水玄武岩和辉长岩转化成榴辉岩 ,这是一种密度较大的主要由石榴石和榴辉石组成的岩石（Ｎａ -Ｃａ单斜辉石类）。含水变质玄武岩转化成榴辉岩释放出大量的Ｈ２Ｏ ,因而增加了俯冲板块的密度。Ｋｉｒｂｙ 等指出脱水反应触发了中等深度（５０～３００ｋｍ）的板内地震 ,并且指出在冷俯冲带观测到的较深板内地震可能反映了榴辉岩形成的动力阻挡作用。对某个俯冲带来说 ,榴辉岩形成的深度和性质以及板块的脱水作用依赖于俯冲洋壳所造成的压力（Ｐ） -温度（Ｔ）条件。俯冲带温度随深度而异是因为聚合速度、热结…     

南黄海千里岩岛榴辉岩的矿物化学及成因探讨

南黄海千里岩岛地处中国华南板块与华北板块缝合线位置,其基底由强烈韧性变形的构造片麻岩组成,并出露具重要大地构造标型意义的超高压榴辉岩类岩石。本文通过对南黄海千里岩岛榴辉岩中主要造岩矿物石榴石的矿物化学研究,探讨了榴辉岩的成因。研究表明,千里岩地区高压变质岩是由于华北与华南两大陆块拼合时,处于其间的岛弧拉斑玄武岩沿碰撞带下插到华北陆块之下,从而使千里岩地区发生高压变质作用,形成了榴辉岩和片麻岩等,后期的构造折返使其上升到地壳上部。     

青岛C类榴辉岩的岩石学矿物学及其地质意义

本文利用X荧光光谱定量分析、电子探针分析和X衍射分析对青岛C类榴辉岩作了岩石学、岩石化学和矿物化学研究,计算了青岛C类榴辉岩的成岩温度、压力条件及古地温梯度,最后提出了其成因是早元古代早期华南陆块向华北陆块俯冲时,大洋碱性橄榄玄武岩在低温高压环境发生变质作用形成C类榴辉岩和蓝闪石片岩。早元古代的变质作用使C类榴辉岩平衡温度升高,蓝闪石片岩消失。     

冲绳海槽海底热液活动区玄武岩的矿物学和岩石化学特征及其地质意义

１９９２年５月－１９９２６月对绳海槽热液活动区进行调查采样，对拖网采到的新鲜的玄武岩样品做了斑晶矿物学及岩石化学研究。结果表明，冲绳海槽玄武岩的斑晶矿物主要由橄榄石、单斜辉石、斜方辉石和斜长石组成，副矿物有铬铁尖晶石和磁铁矿，因而将样品定为橄榄玄武岩。     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,