单突堤后的波浪绕射

波浪绕射现象是确定港域掩护状况的主要因素,在设计港口防波堤工程时必须予以考虑,以便根据港口使用要求,选择最佳的外堤布置方案,确保船舶作业安全并节省工程投资。防波堤工程可有各种不同布局,其中最常见的一种为单突堤。其它如岛堤、双突堤,从计算堤内水域波况的观点着眼,在一定条件下其性质亦属于单突堤一类。因此,研究单突堤后的波浪绕射规律具有较普遍的实际意义。     

港池泊稳的能量平衡方程数值模拟

对基于能量平衡方程的多向随机波浪传播数学模型进行改进,通过模拟不同防波堤绕射引起的港池泊稳,验证模型的合理性和有效性。利用非线性弥散关系提高模型计算浅水变形的精度;采用二次逆风差分格式离散控制方程,避免了加入绕射项引起的数值耗散;并将文氏谱加入模型中,使其更加适合中国海域的工程应用。应用改进后模型绘制的双突堤和岛式防波堤绕射系数图与我国《海港水文规范》图进行了对比。对比结果十分接近,可以较好地描述港池的泊稳状况,为综合计算波浪在近岸的浅水变形、折射、绕射、反射和能量耗散等作用奠定了基础。     

双突堤波浪绕射的数学模型

双突堤是常见的一种防波堤布置型式。因此研究双突堤的波浪绕射数学模型和数值计算方法是有理论意义和实用价值的。本文引用数学物理方程中的单源点法,提出了两种双突堤波浪绕射的数学模型。本模型采用线性简谐波理论,假设水深为定值。     

不同因素对人工岛波浪绕射影响研究

为研究人工岛尺度变化和波浪方向分布对人工岛绕射波浪的影响,基于MIKE21-BW模型应用数值方法模拟人工岛波浪绕射过程。数值结果与Briggs等的物理试验结果的对比表明两者吻合较好,验证了模型的适用性。在规则波条件时,圆形人工岛绕射波浪的数值结果与线性波浪绕射理论解基本一致;采用该模型分别模拟了6种尺度的圆形人工岛、单向不规则波和9种方向分布θ_(max)、4种谱峰周期条件时绕射波浪分布情况。分析结果表明,圆形人工岛绕射系数随着尺度的增加,掩护区绕射系数随之减小;θ_(max)在10°~45°范围内,随着θmax的增大,绕射系数随之增大,θ_(max)在45°~75°内绕射系数变化较小;随着谱峰周期的增加,绕射系数随之增大。研究成果既为相关规范的完善提供了基础,也为相关工程设计提供了参考。     

不同尺度人工岛波浪绕射系数的研究

为研究人工岛沿波浪传播方向尺度变化对绕射系数的影响,本文基于MIKE21-BW模型,数值模拟研究了入射波为不规则波时人工岛尺度不同对其绕射系数的影响。通过数值结果与Briggs物理模型试验结果进行了对比,结果吻合较好,验证了模型在研究波浪绕射问题上的适用性。在未考虑结构物沿波浪传播方向尺度对绕射系数的影响时,将数值结果与《海港水文规范》(JTS145-2-2013)规范结果比对,结果差异较小;本文采用上述模型模拟了结构物沿波浪传播方向7种不同尺度时的波浪绕射情况,分别是0.5Ls,Ls,2Ls,3Ls,4Ls,5Ls及6Ls,通过对不同尺度时的波浪绕射系数变化的分析,得到结果:结构物尺度在0.5Ls~2Ls范围内时,绕射系数随着结构物尺度的增大而变大;结构物尺度在3Ls~6Ls范围内时,绕射系数随着结构物尺度的增大而减小;在人工岛岛壁附近和其掩护区内绕射系数变化较明显;人工岛结构物尺度变化对绕射系数值有影响。文中给出了不同尺度人工岛绕射系数等值线图,可为工程设计中绕射波高确定提供参考。     

多向不规则波绕射的数值模拟

采用有限元求解Ｂｏｕｓｓｉｎｅｓｑ方程数值计算模型,对单突堤和双突堤的波浪绕射进行了数值模拟,并与物模试验进行对比验证。模拟结果表明入射波浪的方向分布对波浪的绕射具有明显的影响,使防波堤后的波浪增大,开阔区域的浪浪减小,波浪的方向分布对港内波浪的分布具有一定的均化作用。     

考虑边界波浪方向的缓坡方程自适应求解模型

缓坡方程是描述近岸波浪运动较好的数学模型之一。在发展的自适应有限元求解缓坡方程的基础上,采用迭代求解的方法,确定波浪相对于边界的入射方向,从而对边界条件进行改进,建立了求解缓坡方程的数值计算模型。典型算例表明,考虑波浪相对于边界的入射角度后,模型可以更好地模拟吸收波浪边界,同时对多向波对双突堤的绕射进行了模拟研究,与试验结果比较表明,所建立的数值计算模型能够适用于多向不规则波传播过程的模拟研究。     

人工岛游艇码头泊稳试验与数值模拟研究

针对青岛万达游艇码头项目进行了港域波浪物理模型试验研究。试验表明,当口门处人工岛护岸采用直立式结构时,港池入口处波浪反射严重,港内波高较大,各码头泊位不满足泊稳要求;当采用斜坡式结构时,港内波高显著减小,游艇码头泊位满足泊稳要求,工作船泊位不满足泊稳要求,其最大波高比允许值仅大0.1m。采用MIKE21BW模型,考虑波浪的折射、绕射、反射及破碎等物理过程,对港域的波浪传播变形过程进行数值模拟,计算得到了港域的波浪分布状况,将计算结果与试验结果进行比较,吻合良好,表明该模型可用于近岸波浪的传播变形模拟及港域泊稳计算,计算结果可用于游艇码头结构设计。     

日照豪迈码头港池布局对泥沙输移影响研究

港池的布局会改变其周边海域水动力条件及其泥沙冲淤状况,为了进一步了解其影响程度,本文以山东日照豪迈重工临港厂区运输码头的改造工程为研究对象,利用平面二维数值模型MIKE21/3 Integrated Models,建立了潮流和波浪耦合作用下的泥沙输移数值模型,对该工程附近海域进行了波浪、潮流和泥沙输移的数值模拟。同时采用实测数据对数值模型进行了验证,数值模拟结果与实测资料拟合较好,表明MIKE21能有效地模拟运输码头及其周围海域潮流的变化过程。以日照豪迈重工临港厂区运输码头为依托,基于数值模拟结果,分析不同改造方案下的水动力条件和泥沙冲淤状况。结果表明:港池布局对水动力条件影响甚微,对地形地貌冲淤影响较大;模拟结果确定港池南向开口为最佳改造方案,为工程的规划和设计提供科学依据。     

矩形港池的港内共振研究

在理想地形条件下,应用MIKE 21-BW模块进行了不同入射波周期的矩形港池的港内波高分布计算,数值计算结果表明,港池尺度为入射波半波长的整数倍时,港内将产生驻波共振;港内共振与口门宽度相关.在某一尺度下,口门宽度越小,港池共振越明显;港池口门的位置会对港池共振的模式发生影响,可能导致出现第二类共振频率.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

Flow Cytometric Analysis of Coastal Lagoon Bacterioplankton and Picophytoplankton: Fixation and Storage Effects

The effect of different fixation and storage protocols on the flow cytometric (FCM) simultaneous analysis of bacterioplankton and phytoplankton in coastal seawater samples (Mediterranean coastal lagoons) was investigated. FCM measurements (cell number, fluorescence and scatter characteristics) were obtained through DAPI staining. Three fixatives [glutaraldehyde (GA), formaldehyde (FA) and paraformaldehyde (PFA)] and two storage (3 months duration) methods (5 °C and −196 °C) were tested. Two dominant populations were detected in studied samples: bacteria and eukaryotic picophytoplankton. Adding fixatives (2% final concentration) appears necessary to obtain FCM exhaustive counts of all the bacteria and phytoplanktonic cells. This was related to the permeation effect of fixatives which allowed a better DAPI staining of the cells. Maximum fluorescence, i.e. optimal staining of the cells was obtained with FA or PFA, and significant lower fluorescences with GA. Fixed samples stored at 5 °C induced rapid cell loss. Only storage in liquid nitrogen of samples fixed with FA or PFA, allows mid-term (≥4 months) preservation of bacteria or picophytoplankton cell numbers, and limited evolution of DAPI-induced fluorescence and scatter characteristics.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,