渭河盆地中土层场地对地震动的放大作用

土层场地对地震动的影响较大,建(构)筑物的选址及其抗震设防必须考虑土层场地的放大作用,以避免或减轻其震害.汶川地震中,布设在渭河盆地中的数字强震动台网共有27个台站(包括2个基岩台站和25个土层台站)获得良好的主震加速度时程.利用这些加速度时程,选择汤峪台做为参考场地,基于考虑几何衰减的传统谱比法分析研究了25个土层场...     

自贡市西山公园地形对地震动的影响

不规则地形和土层对地震动的影响较大,建(构)筑物选址及其抗震设防必须考虑地形和土层场地的放大效应,以避免或减轻其震害.利用自贡地形台阵记录的汶川地震(M_s8.0)的主震加速度时程,基于传统谱比法分别研究了地形和土层场地对地震动的放大效应.结果表明:(1)地形场地在低频的放大效应不明显,最大仅为1.24;在高频的放大效应较显著,在1~10 Hz频带,山顶的放大效应最大,EW、NS和UD地震动的最大放大效应分别为4.15、3.61和2.41,对应频率分别为5.72 Hz、6.46 Hz和7.44 Hz;在10~20 Hz频带,靠近山顶的山脊上某个地震动分量的放大效应最大,7#台站EW、5#台站NS和7#台站UD地震动的最大放大效应分别为9.10、5.56和2.52,对应频率分别为16.97 Hz、16.91 Hz和17.91 Hz.(2)地形场地的最大放大效应随高度有增加的趋势,且在0.1~10 Hz频带随高度增加的趋势更加明显.(3)土层场地水平向地震动在2 Hz以上开始明显放大,竖向地震动在4 Hz以上开始明显放大;EW、NS和UD地震动的最大放大效应分别为13.4、12.168和6.0,对应频率分别为6.94 Hz、7.55 Hz和10.8 Hz.(4)土层场地与地形场地的最大放大效应相比较,前者显著大于后者,对于水平向地震动,前者至少是后者的3倍以上;对于竖向地震动,前者至少是后者的2.5倍以上.(5)无论是地形场地还是土层场地,地震动的最大放大效应均有水平向大于竖向的特征.     

北京地区中硬场地对地震动加速度反应谱的放大效应研究

当前,合理确定地震动峰值加速度与反应谱特征周期是工程场地地震动参数确定工作的主要内容。本文以北京地区典型中硬场地为研究对象,分析场地条件对不同周期地震动反应谱值的影响。首先,计算不同震级、震中距条件下的基岩地震动加速度反应谱,合成基岩输入地震动时程;再利用110个工程场地的钻孔资料进行土层地震反应计算,分析中硬场地条件对不同输入环境下的地震动加速度反应谱值的放大效应。结果表明,中硬场地对高、中频震动放大效应明显,尤其是对0.2-0.5s周期段地震动加速度反应谱值的放大倍数大多在1.3以上;场地覆盖层厚度变化对不同频段地震动加速度反应谱值的放大倍数所产生的影响是不同的,与场地自振周期的相关性很强;在不同的地震动输入环境下,中硬场地对不同频段地震动加速度反应谱的影响是不同的,这一结论对实际的抗震设防工作具有一定参考价值。     

基于小田原试验场地数据的不同基岩输入模型对预测地震动特征的影响研究

随着强震台网的密布及观测记录的增加,为研究各类局部场地地震反应预测模型的合理性提供了有效的参考依据,也使利用强震记录及场地条件研究地震动特征成为可能。选取场地地质参数资料和地震记录数据齐全的日本小田原（Ashigara Valley）盲测试验场地,通过对比不同地震动输入方式及场地反应分析模型,研究地震动特征,分析现有模型的优劣。基于1990年8月5日M5.1强震事件的地表基岩记录和地下基岩地震记录,采用地下台强震记录直接输入、地表基岩台强震记录减半为基底地震动输入、地表基岩台强震记录反演为基底地震动输入作为3种基岩地震动输入。基于局部场地条件分别建立一维等效线性模型、二维黏弹性模型及二维时域等效线性化模型等工程中常用的场地数值分析模型,进行局部场地地震反应分析,预测该盲测场地的地表地震动特征,并与对应的实测强震记录结果进行对比,分析不同基岩地震动输入方式对预测地震动特征及地表土层反应谱特征的影响,重点分析地震动输入、土体非线性、场地横向不均匀性及几何与非线性特征共同作用等因素对地表地震动特征的影响,以期为地表地震动的合理预测提供参考。     

2020年7月12日唐山古冶5.1级地震揭示的北京城区地震动场地效应分析

局部场地条件对地震动特性影响显著,深厚的软弱覆盖层引起的地震动场地效应会显著放大中长周期反应谱。采用谱比法,对2020年7月12日唐山古冶5.1级地震中获得的部分强震动记录进行统计,发现在本次地震中北京城区的地震动场地效应显著,深厚覆盖层明显放大了加速度反应谱,在T=1.2 s左右反应谱放大倍数可达4.0,说明北京地区的场地和盆地效应使得远场地震动的中长周期成分显著放大。此外,发现参考基岩场地记录是否与土层场地处遭受的基岩地震动一致,仍然是制约统计结果可靠性的关键因素。      

黄土高填方场地地震动参数特性分析

削山造地后形成的黄土高填方场地对地震动参数特性影响较大。以实际工程项目为研究对象,构造不同填土高度的计算剖面,采用一维等效线性化方法计算土层地震动参数,分析基岩地震动输入参数和填土高度对场地地表放大效应的影响。研究表明:场地地震放大系数随填土层的高度增加呈递减趋势。在多遇地震动和基本地震动作用下,场地地震放大系数递减速度比罕遇地震动和极罕遇地震动作用下要大。当填土高度达到一定程度后放大效应趋于平稳;填土高度的变化,会改变地表加速度反应谱的形状。填土高度越大,地表反应谱长周期的频谱成分越显著,反应谱曲线向后移,反应谱峰值点均明显向长周期移动,并出现多个峰值点,反应谱特征周期值变大;下伏基岩的刚度越大,地表峰值加速度的放大效应越大。地表加速度反应谱特征值相比变小。当填土高度增大到一定程度时,下伏基岩的种类对地表地震动特性影响则不明显。该研究成果对高填方场地的地震安全评价和结构抗震设计提供参考。     

渤海海域软土层土对地震动参数的影响研究

渤海海域软土层土对场地设计地震动参数取值具有显著影响。选取渤海中部钻孔剖面作为计算场地模型基础,分别构建软土和硬土场地模型,并通过改变软土层厚度,构造新的场地模型。采用等效线性化方法（EL法）和非线性计算方法（NL法）分别对场地模型进行地震反应分析,分析了海底软土层土对地震动参数的影响。研究结果表明:海底软土层土对地震动峰值加速度的影响显著,随着地震动输入增加,软土层放大效应减弱,减震作用逐渐增强;EL法中,软土层土对基岩反应谱的高频部分具有明显滤波作用,而NL法中,滤波作用较弱,海底面反应谱随地震动输入的增大先放大后减小;软土层土会降低设计地震动地震最大影响系数,增大特征周期。对于海域工程,特别是深基础工程抗震设计地震动参数的确定,从保守角度考虑,建立场地模型时建议删除软土层。     

Numerical study on basin-edge effects in the seismic response of the Gubbio valley,Central Italy

The Gubbio basin in Central Italy is a intermountain basin of extensional tectonic origin, typical of Central and Southern Apennines, characterized by moderate seismicity. The strongest recorded event within the area is a magnitude 5.7 earthquake which occurred on 29 April 1984 along the Gubbio fault, bordering the eastern side of the basin. The main objective of this study is to analyze the features of earthquake ground motion as related to basin-edge effects, by performing physics-based numerical simulations of the 1984 earthquake through a high-performance spectral element code. The simulated ground motions are found in reasonable agreement with the recorded motions when using the kinematic source model developed by Ameri et al. (Bull Seismol Soc Am 99:647–663, 2009), with a rise-time equal to 1 s and a nucleation point located in the middle of the fault. Pronounced differences were noted between records from the basin and adjacent sites at outcropping bedrock, owing to both the strong impedance contrast between soft alluvial sites and bedrock formations (lithostratigraphic amplification), as well as lateral discontinuities related to the 2D/3D geometry of the basin (generation of surface waves). Since the fault was located beneath the basin, 1D amplification effects were found to be more relevant than those associated with the generation of surface waves from the basin edge. Finally, an envelope delay spectrum was computed for the simulated ground motions, showing that surface waves are excited in the frequency band of 0.2–0.8 Hz with a significant increase of ground motion duration within the basin.     

Evaluation of the measured seismic response of the Mexico City Cathedral

The seismic response of the Mexico City Cathedral built of very soft soil deposits is evaluated by using motions recorded in various parts of the structure during several moderate earthquakes. This unique set of records provides significant insight into the seismic response of this and other similar historic stone masonry structures. Free‐field ground motions are carefully compared in time and frequency domains with motions recorded at building basement. The dynamic characteristics of the structure are inferred from the earthquake records by using system identification techniques. Variation of seismic response for different seismic intensities is discussed. It is shown that, due to the soil–structure interaction, due to large differences between dominant frequencies of earthquake ground motions at the site and modal frequencies of vibration of the structure, and due to a particularly high viscous damping, seismic amplifications of ground motion in this and similar historic buildings erected on soft soil deposits are much smaller than that induced in most modern constructions. Nevertheless, earthquake records and analytical results show that several components of the structure such as its central dome and the bell towers may be subjected to local vibrations that significantly amplify ground motions. Overall, results indicate that in its present state the structure has an acceptable level of seismic safety. Copyright © 2008 John Wiley & Sons, Ltd.     

Amplification effects from earthquakes and ambient noise in the Dead Sea rift (Israel)

Seven sites were instrumented in the Parsa area located in the seismically active Dead Sea rift system. Moderate and weak motions generated by earthquakes and ambient noise were used to identify amplifications due to geological and topographic effects.Three observation methods were applied to estimate site effects: (1) conventional soil–bedrock station-pair spectral ratios for earthquake motions and microtremors; (2) horizontal-to-vertical component spectral ratios for shear-waves observed simultaneously at a site (receiver function estimates) and (3) horizontal-to-vertical spectral ratios of microtremor measurements (Nakamura estimate). The site response spectra of soil sites exhibited significant peaks between 1 and 3 Hz with amplification factors typically within the range of 2.5–4.0. A bedrock site on the high plateau near the escarpment top showed a peak between 2 and 3 Hz, mainly due to an EW oscillation of the NS topographic feature. Our observations indicated that seismograms recorded in the tunnel were either enriched or depleted at certain frequencies owing to interference of incident and surface-reflected waves.     

基于台阵记录的局部场地条件地震动效应分析

基于自贡西山公园山体地形影响台阵和唐山响堂土层场地台阵的地震动记录, 采用互相关分析、 相干系数分析、 傅里叶谱比法和考虑相干系数的傅里叶谱比法, 对比研究了山体地形和土层场地两种局部场地条件对地震动的影响。 结果表明, 局部场地条件下的地震动效应与地震波的频率成分相关。 低频地震波由于其波长较长, 易于穿过土层场地和山体地形发生衍射, 从而导致二者地震动显著相关, 但二者在该频段的地震动场地效应差异不大; 较高频率的地震波由于其波长较短, 更容易受土层场地条件和山体地形条件的影响, 造成二者地震动场地效应差异显著。 此外, 由于山体顶部的尺寸变小, 低频长波长地震波容易在该位置发生衍射, 导致山顶周边测点的地震动相关性增加, 而较高频率的地震波则容易引起山顶局部场地发生共振效应。 山体地形上相邻位置的地震动差异一般较大, 相关性较低, 这与山体地形不同位置的几何形状对较高频率的地震波影响有关; 山底基岩的地震动受山体地形的影响较小, 该位置的地震动效应机制尚需作进一步研究。      

唐山地区强震动记录的应用研究初探

本文给出了唐山地区强震动记录应用研究的两个实例,提出了建筑结构采用时程分析时选用强震动记录的原则和方法,通过对唐山地区强震动记录的分析处理,得到了其峰值加速度及加速度反应谱,确定了本地区进行弹性时程分析时选用的强震动记录;研究了局部场地条件对地震动影响的唐山响堂三维强震动观测台阵,以唐山响堂台阵2号测井(地下32m)的基岩强震动作为输入,通过2号测井的土层剖面,利用2个一维土层地震反应分析程序,分别计算得到地表的峰值加速度和加速度反应谱,并把计算结果与同次地震相应的地表强震动记录峰值加速度与加速度反应谱进行了对比分析。     

A new approach of selecting real input ground motions for seismic design: The most unfavourable real seismic design ground motions

This paper presents a new way of selecting real input ground motions for seismic design and analysis of structures based on a comprehensive method for estimating the damage potential of ground motions, which takes into consideration of various ground motion parameters and structural seismic damage criteria in terms of strength, deformation, hysteretic energy and dual damage of Park & Ang damage index. The proposed comprehensive method fully involves the effects of the intensity, frequency content and duration of ground motions and the dynamic characteristics of structures. Then, the concept of the most unfavourable real seismic design ground motion is introduced. Based on the concept, the most unfavourable real seismic design ground motions for rock, stiff soil, medium soil and soft soil site conditions are selected in terms of three typical period ranges of structures. The selected real strong motion records are suitable for seismic analysis of important structures whose failure or collapse will be avoided at a higher level of confidence during the strong earthquake, as they can cause the greatest damage to structures and thereby result in the highest damage potential from an extended real ground motion database for a given site. In addition, this paper also presents the real input design ground motions with medium damage potential, which can be used for the seismic analysis of structures located at the area with low and moderate seismicity. The most unfavourable real seismic design ground motions are verified by analysing the seismic response of structures. It is concluded that the most unfavourable real seismic design ground motion approach can select the real ground motions that can result in the highest damage potential for a given structure and site condition, and the real ground motions can be mainly used for structures whose failure or collapse will be avoided at a higher level of confidence during the strong earthquake. Copyright © 2007 John Wiley & Sons, Ltd.     

Local Site Effects in the Town of Benevento (Italy) from Noise Measurements

— The study of ground motion amplification produced by surface geology is extremely interesting in the Benevento area, Southern Italy, as it is characterized by high seismic hazard. The present moderate-to-low seismicity makes the noise method appropriate to estimate the seismic site response in the area. The three components of seismic noise have been recorded in five sites in the Benevento metropolitan area characterized by different surface geology, in order to estimate the seismic site response. In evaluating site amplification effects we used the direct interpretation of amplitude spectra and standard spectral ratio techniques, evaluating sediment-to-bedrock, sediment-to-average and H/V spectral ratios. The temporal evolution of the noise spectra is analysed within one day, in order to assess the stationarity of the noise signal. The noise wavefield properties have been studied through polarization analyses in selected bands of frequency, where spectral peaks are observed to dominate, to better understand the real nature of those peaks. Results give evidence of low amplification levels, missing any correlation between spectral amplitudes and sediment thickness over the basement. We interpret this result as due to the poor impedance contrast between sediments and basement, which is characterized by low values of shear waves velocity. Moreover, sharp amplitude peaks are observed in the raw spectra of the sediment-sites, in the 2–4 Hz frequency band; a numerical simulation interprets this effect as possibly associated with a wide-scale structure, invoking the presence of a sharper impedance contrast at greater depth. At high frequencies the action of ambient noise sources, mainly active on horizontal components of motion, is retained dominant to generate the prominent peaks observed in the H/V spectral ratios; in some cases the presence of a near-surface low-velocity layer can contribute to amplify the seismic motion generated at these frequencies.     

The response law of far-field seismic ground motion of the Wenchuan earthquake and its damaging mechanism in the Loess Plateau

A series of housing collapses and other serious damage was caused by the 2008 Wenchuan M_S 8.0 earthquake in the seismic intensity Ⅵ areas of the Loess Plateau, which is hundreds of kilometers away from the epicenter, and which showed a remarkable seismic intensity anomaly. The seismic disasters are closely related to the seismic response characteristics of the site, therefore, the systematic study of the far-field seismic response law of the Wenchuan earthquake in the Loess Plateau is of great significance to prevent the far-field disaster of great earthquake. In this paper, the seismic acceleration records of several bedrock stations and loess stations from the seismogenic fault of the Wenchuan earthquake to the Loess Plateau were collected, and the attenuation law of ground motion along the propagation path and the characteristics of seismic response on the loess site are studied, and the mechanism of amplification effect of ground motion is analyzed based on the dynamic feature parameters of the loess site obtained through the HVSR method. Taking a typical loess site of thick deposit as the prototype, a series of shaking table tests of dynamic response of loess site models with different thicknesses were carried out. Amplification effect, spectral characteristics of acceleration in model sites were analyzed under the action of a far-field seismic wave of the Wenchuan earthquake. The results show that seismic attenuation on the propagation path along the NE strike of the seismogenic fault to the Loess Plateau is slower than that in other directions, and the predominant period range of ground motion on bedrock site of the Loess Plateau presents broadband characteristics. Because the natural periods of loess sites with thick deposits are within the predominant period range of bedrock input wave, loess sites appear significant amplification effect of ground motion, the horizontal acceleration of ground motion exceeds 0.1 ?g, the seismic intensity reaches 7°. The thicker the loess deposit is, the more significant the change of spectral characteristics of ground motion on loess sites, and the narrower the predominant period range of ground motion becomes, and the closer it is to the natural period of loess sites. Therefore, for some old houses on thick loess sites, the poor seismic performance and strong seismic response eventually led to their collapses and damages because their natural periods are very close to the predominant period of ground motion of the Wenchuan earthquake on thick loess sites; For these damaged high-rise buildings, the resonance effect might be the main reason for their damages because their natural periods are included in the predominant period range of ground motion of the Wenchuan earthquake on thick loess sites.These research results would provide a basis for seismic disasters prediction and evaluation and seismic design of construction engineering in the Loess Plateau.     

Seismic response of deep Quaternary sediments in historical center of L’Aquila City (central Italy)

On 6 April 2009 a M_w=6.1 earthquake produced severe destruction and damage over the historic center of L’Aquila City (central Italy), in which the accelerometer stations AQK and AQU recorded a large amount of near-fault ground motion data. This paper analyzes the recorded ground motions and compares the observed peak accelerations and the horizontal to vertical response spectral ratios with those revealed from numerical simulations. The finite element method is considered herein to perform dynamic modeling on the soil profile underlying the seismic station AQU. The subsurface model, which is based on the reviewed surveys that were carried out in previous studies, consists of 200–400 m of Quaternary sediments overlying a Meso-Cenozoic carbonate bedrock. The Martin-Finn-Seed's pore-water pressure model is used in the simulations. The horizontal to vertical response spectral ratio that is observed during the weak seismic events shows three predominant frequencies at about 14 Hz, 3 Hz and 0.6 Hz, which may be related to the computed seismic motion amplification occurring at the shallow colluvium, at the top and base of the fluvial-lacustrine sequence, respectively. During the 2009 L’Aquila main shock the predominant frequency of 14 Hz shifts to lower values probably due to a peculiar wave-field incidence angle. The predominant frequency of 3 Hz shifts to lower values when the earthquake magnitude increases, which may be associated to the progressive softening of soil due to the excess pore-water pressure generation that reaches a maximum value of about 350 kPa in the top of fluvial-lacustrine sequence. The computed vertical peak acceleration underestimates the experimental value and the horizontal to vertical peak acceleration ratio that is observed at station AQU decreases when the earthquake magnitude increases, which reveals amplification of the vertical component of ground motion probably due to near-source effects.     

一种实时场地校正方法及其在地震预警中的应用

地震预警系统对地震数据处理的实时性要求极高。其系统数据来源除布设在基岩的测震台站外,还有大量非基岩场地的强震动台站和地震烈度仪台站,其场地影响不容忽视。为了考虑震级估算和地震动场预测中的场地影响,需实时对各种场地条件下的地震波形进行校正。目前处理一般使用某个标量来表征场地放大效应。本文采用一种实时的场地校正方法,首先计算目标场地与参考场地的谱比,然后通过最小二乘法、双线性变换将谱比转化为因果递归的无限冲激响应(IIR)时域滤波器,之后可以应用该滤波器进行实时场地校正。该方法考虑了场地放大系数的频率依赖性,相比于标量校正提高了准确度。应用我国四川和日本部分强震动台站记录,验证并讨论了这种实时场地校正方法在地震预警中的应用效果。     

Analytical solution for vertical site response analysis and its validation

Existing studies for site response analysis in geotechnical earthquake engineering have widely concentrated on the horizontal component of the ground motion. However, strong vertical ground motions have been repeatedly observed, resulting in significant vertical compression damage of engineering structures. Furthermore, for the seismic design of critical structures(e.g. large-scale dams and nuclear power plants), the ground motions in all three directions should be considered. Therefore, there is a need to investigate the site response subjected to the vertical component of the ground motion, especially for the seismic design of critical structures. Consequently, in this study, a numerical program for vertical site response analysis is proposed based on the commonly used analytical transfer function method. The proposed program is then validated against well-documented case studies obtained from the Japanese KiK-net(Kiban Kyoshin network) downhole array monitoring system. Results show that the response spectra at the ground surface are well predicted in the low frequency range(5 Hz), while discrepancies are observed in the high frequency range. However, the high frequency discrepancies do not significantly affect the overall prediction accuracy, as the overall seismic response of geotechnical structures are usually dominated by low frequency vibrations. Furthermore, the limitations in the analysis are also discussed.