基础隔震结构的减震耗能特性分析

根据基础隔震理论,在钢筋沥青隔震礅的基础上,提出一种新型钢结构隔震礅,设计和制作了缩尺房屋模型,并对其进行振动台试验。通过对隔震结构模型的动力特性、地震响应及能量平衡分析,绘制试验过程中的加速度及能量时程曲线,研究钢隔震礅应用于低层框架结构的减震耗能能力。大量工程实例可以看出该隔震礅隔震效果显著,制作简单、价格低廉、耐久性好,适于在广大村镇地区低层框架结构中推广使用。试验表明:隔震结构模型在不同的地震作用下,加速度折减系数处在0.24~0.51之间,且结构的阻尼耗能在振动台试验中占总输入能量的60%~70%,对结构耗能起主导作用,说明该基础隔震装置不仅具有较好的减震耗能特性能,对于控制隔震层的位移也有好的效果。     

基于能量原理的阻尼器隔震结构地震响应预测

建立在地震作用下设置阻尼器的基础隔震结构在最大地震响应时刻的能量平衡方程,给出了结构隔震支座和阻尼器的能量表达式,演算了基于能量平衡的设置阻尼器的基础隔震结构的地震响应预测式.选用人工地震波和天然地震波,利用时程分析法的解析值验证了地震响应预测式的精度,比较研究了仅设置粘性阻尼器和同时设置粘性阻尼器和滞回阻尼器的基础隔震结构的抗震性能.研究表明:对于不同的输入地震波,能量法的地震响应预测值包络了多数时程分析的结果,能较好地预测基础隔震结构的地震响应值.在基础隔震结构设计中,建议在隔震层同时设置粘性阻尼器和滞回阻尼器,粘性阻尼器的阻尼比在0.3 ～0.4之间.     

不同支座布置下组合基础隔震结构能量反应分析

通过对5种不同支座布置方案的组合基础隔震结构施加不同场地条件下的双向水平地震波,研究了场地类别和地震波加速度峰值及支座布置方式对结构总输入能量的影响,并进行了耗能分析。结果表明,随着地震波峰值的增大,结构总输入能量增大;相同地震峰值条件下,场地土越软,总的输入能量越大;组合隔震结构应用于软土场地时隔震层滞回耗能比更大,隔震效果更好;组合隔震结构两种支座中选择分散布置方案时,隔震层耗能比更大,隔震效果优于支座集中布置方案。     

并联复合隔震体系的地震耗能机制和能量响应分析

运用能量分析法对并联复合隔震体系的地震耗能机制和能量响应进行了分析和探讨。首先,以层间剪切模型的多自由度运动微分方程为基础,建立了并联复合隔震体系的能量平衡方程。其次,引入状态空间法对并联复合隔震体系进行时程分析得到体系的地震响应,并以此为基础计算了各项能量。最后,以7质点多自由度体系为仿真对象,对并联复合隔震体系的耗能机制及其主要隔震层参数和不同特性地震动对能量响应的影响进行了分析。结果表明,并联复合隔震体系地震总输入能主要由滞回耗能和阻尼耗能承担;摩擦承压比和摩擦系数对能量响应有重要影响,存在最优取值区间;地震能量响应受地震动特性影响较大。     

基于拟力法的基础隔震结构抗震性能和能量分析

基于拟力法基本理论,建立了隔震结构杆系计算模型,同时考虑隔震支座的剪切变形和弯曲变形的影响,推导了基础隔震结构的运动方程和能量方程,编制程序对隔震结构进行地震下的动力非线性分析和能量分析。通过与SAP2000计算结果的对比,验证了本文方法的有效性和程序的正确性。数值算例结果表明,本文提出的方法与变刚度的时间积分法相比计算效率明显提高;本文方法可以考虑上部结构的非线性,可以得到隔震支座及上部结构各构件的塑性耗能;通过对比基础隔震结构和抗震结构在地震作用下的位移、加速度及耗能情况,证明了隔震结构的隔震效果。本文拓展了拟力法的应用范围,为隔震结构的动力非线性分析及能量分析提供了一种新思路。     

某平面不规则大底盘多塔楼隔震结构的抗震性能分析

对8度区某平面不规则大底盘多塔楼基础隔震结构进行了抗震性能分析。根据结构特点采用多串质点系计算模型,利用时程分析法计算对比了隔震结构和非隔震结构在多遇地震作用下的水平剪力,并验算了隔震结构在罕遇地震作用下的水平剪力、层间位移和位移角。分析表明,在水平地震作用下隔震结构相对非隔震结构表现出了良好的减震效果,罕遇地震作用下隔震结构各项指标均满足规范要求。     

变刚度钢管混凝土短柱隔震结构弹塑性动力分析

采用HBTA2.5程序,对一变刚度钢管混凝土短柱隔震结构进行了弹塑性时程分析。分析结果表明,其隔震装置的水平变形和耗能能力可以大大减轻地震对结构的影响。提出钢管混凝土短柱隔震结构在工程应用将有很好的发展前景。     

设置抗拔型三重摩擦摆隔震支座框架结构地震响应分析

抗拔型三重摩擦摆隔震支座是一种新型隔震支座。以框架结构为例,利用ANSYS软件建立了6层和10层普通抗震结构和带该支座的基础隔震结构模型;通过模态分析,得到了结构的自振周期;通过地震响应分析,提取了6层框架隔震层和顶层的位移、加速度和剪力时程曲线,并提取了不同层数不同结构类型的各层间位移、加速度幅值。结果表明：与抗震结构相比,基础隔震结构周期显著增大;隔震结构的变形主要集中在隔震层,隔震层以上的结构基本为整体平动,结构的地震位移反应得到了有效的减小;采用抗拔型三重摩擦摆隔震支座能降低结构地震加速度反应;设置抗拔型三重摩擦摆隔震支座的多层数隔震结构的能量衰减不如低层数的隔震结构迅速。     

基于易损性的基础隔震结构地震动选取方法研究

对基础隔震结构进行动力弹塑性时程分析时,地震记录的选择是关键.提出基于基础隔震结构弹塑性动力放大系数谱进行地震记录选取的方法:首先采用动力弹塑性时程分析方法对基础隔震结构的两自由度简化模型进行分析,得到结构的动力放大系数谱;然后采用谱匹配的方法选取地震记录,对一8层混凝土框架结构的基础隔震结构进行增量动力分析、地震易损...     

组合基础隔震在建筑工程中的应用

隔震作为一种新的抗震技术,已广泛应用于新建和加固的建筑工程,同时,许多新型式的支座得到了开发和应用。组合基础隔震是一种新的隔震设计思想,能充分应用不同类型隔震支座的特性,有效降低上部结构地震反应。本文介绍了组合基础隔震在某一工程中的应用,工程中使用的支座包括普通橡胶隔震支座、铅芯橡胶隔震支座和弹性滑板支座三种类型,对全部使用支座进行了常规检测,结构计算采用等效线性法、能量包络法和时程反应分析等方法,计算结果表明:组合基础隔震能有效降低上部结构的反应,隔震层的变形控制在安全范围之内。     

单层工业厂房-TMD减震控制系统研究

提出了采用质量调谐减震控制技术对厂房结构进行减震控制的方法。利用屋盖系统作为附加质量,屋盖支座采用夹层橡胶隔震垫,建立了厂房-TMD系统模型,并用非线性时程分析法对其进行了多种地震动激励下的计算分析,探讨了厂房-TMD减震体系减震效果的参数影响及减震机理。结果表明,采用质量调谐减震技术对单层工业厂房进行减震是一种有效的方法。     

Efficiency of base isolation systems in structural seismic protection and energetic assessment

This paper concerns the seismic response of structures isolated at the base by means of High Damping Rubber Bearings (HDRB). The analysis is performed by using a stochastic approach, and a Gaussian zero mean filtered non‐stationary stochastic process is used in order to model the seismic acceleration acting at the base of the structure. More precisely, the generalized Kanai–Tajimi model is adopted to describe the non‐stationary amplitude and frequency characteristics of the seismic motion. The hysteretic differential Bouc–Wen model (BWM) is adopted in order to take into account the non‐linear constitutive behaviour both of the base isolation device and of the structure. Moreover, the stochastic linearization method in the time domain is adopted to estimate the statistical moments of the non‐linear system response in the state space. The non‐linear differential equation of the response covariance matrix is then solved by using an iterative procedure which updates the coefficients of the equivalent linear system at each step and searches for the solution of the response covariance matrix equation. After the system response variance is estimated, a sensitivity analysis is carried out. The final aim of the research is to assess the real capacity of base isolation devices in order to protect the structures from seismic actions, by avoiding a non‐linear response, with associated large plastic displacements and, therefore, by limiting related damage phenomena in structural and non‐structural elements. In order to attain this objective the stochastic response of a non‐linear n‐dof shear‐type base‐isolated building is analysed; the constitutive law both of the structure and of the base devices is described, as previously reported, by adopting the BWM and by using appropriate parameters for this model, able to suitably characterize an ordinary building and the base isolators considered in the study. The protection level offered to the structure by the base isolators is then assessed by evaluating the reduction both of the displacement response and the hysteretic dissipated energy. Copyright © 2003 John Wiley & Sons, Ltd.     

改进的基础隔震结构地震作用简化计算方法

在《建筑抗震设计规范》(GB50011-2001)关于隔震结构的简化计算方法中,水平向减震系数的表达式和定义有些不符,假定的隔震结构地震作用分布规律也与实际情况略有出入。本文基于水平向减震系数的定义和实际隔震结构的地震作用分布规律提出了一种改进的隔震结构水平向减震系数、隔震结构总地震作用、隔震结构上部地震作用分布的计算方法,并提出了总水平地震作用减震系数的新概念。本文提出的改进方法具有表达准确、物理意义明确的特点。将本文提出的改进算法计算结果与时程分析计算结果比较,结果显示,改进方法的计算结果与时程分析结果接近,且分布规律一致。     

楼板隔震消能结构体系

提出了一种新型减震结构体系——楼板隔震消能结构体系。该结构体系的特点是:竖向荷载传递途径与传统结构相同,但在楼板与主体结构水平承重构件之间设置高阻尼隔震层,在楼板与主体结构竖向承重构件之间留出空隙,并在其中安装消能阻尼器,使结构在发生水平振动时楼板与主体结构之间能够发生一定的相对运动,产生隔震和消能作用,减小结构的地震反应。本文给出了单层楼板隔震消能结构的运动微分方程,以及基底输入谐和振动时的结构传递函数,并分析了结构参数对传递函数的影响。     

基于希尔伯特-黄变换的汶川地震记录分析

利用HHT方法对6个台站的汶川8.0级地震加速度记录进行EMD分解,进而对地震波输入结构的总能量进行分解,得到地震动能量在IMF分量之间的分布关系。同时通过对各分量边际能量谱的分析,可以从另一方面得到地震波的频谱特性,边际能量谱峰值频率与地震波傅立叶谱的卓越频率相同,边际能量谱也可以作为一种估算震动卓越周期的方法。     

Shake table testing of un‐reinforced brick masonry building test model isolated by U‐FREI

This paper presents a detailed study on feasibility of un‐bonded fiber reinforced elastomeric isolator (U‐FREI) as an alternative to steel reinforced elastomeric isolator (SREI) for seismic isolation of un‐reinforced masonry buildings. Un‐reinforced masonry buildings are inherently vulnerable under seismic excitation, and U‐FREIs are used for seismic isolation of such buildings in the present study. Shake table testing of a base isolated two storey un‐reinforced masonry building model subjected to four prescribed input excitations is carried out to ascertain its effectiveness in controlling seismic response. To compare the performance of U‐FREI, same building is placed directly on the shake table without isolator, and fixed base (FB) condition is simulated by restraining the base of the building with the shake table. Dynamic response characteristic of base isolated (BI) masonry building subjected to different intensities of input earthquakes is compared with the response of the same building without base isolation system. Acceleration response amplification and peak response values of test model with and without base isolation system are compared for different intensities of table acceleration. Distribution of shear forces and moment along the height of the structure and response time histories indicates significant reduction of dynamic responses of the structure with U‐FREI system. This study clearly demonstrates the improved seismic performance of un‐reinforced masonry building model supported on U‐FREIs under the action of considered ground motions. Copyright © 2015 John Wiley & Sons, Ltd.     

基于传力路径的平面不规则RC框架结构减震设计

针对平面不规则RC框架结构,从构件安全层次出发提出基于传力路径的减震设计方法。首先根据广义结构刚度法的基本原理计算结构中所有构件的重要性系数,再假定消能支撑的截面参数,取每层最重要的构件位置布置支撑,经支撑在最不利地震组合下的轴力验算后确定支撑的最终设计参数和数量,然后考虑远场、近场有脉冲以及近场无脉冲地震动从双向输入对结构响应的影响,对减震前、后结构分别进行动力时程分析。分析结果表明,利用此方法优化布置支撑能为结构中重要构件提供有效保护,且在小、中、大震下消能支撑均能运作良好,使整体结构响应得到很好地控制。     

SIMPLE PUSH-OVER ANALYSIS OF ASYMMETRIC BUILDINGS

A simple method for the non-linear static analysis of complex building structures subjected to monotonically increasing horizontal loading (push-over analysis) is presented. The method is designed to be a part of new methodologies for the seismic design and evaluation of structures. It is based on the extension of a pseudo-three-dimensional mathematical model of a building structure into the non-linear range. The structure consists of planar macroelements. For each planar macroelement, a simple bilinear or multilinear base shear–top displacement relationship is assumed. By a step-by-step analysis an approximate relationship between the global base shear and top displacement is computed. During the analysis the development of plastic hinges throughout the building can be monitored. The method has been implemented into a prototype computer program. In the paper the mathematical model, the base shear–top displacement relationships for different types of macroelements, and the step-by-step computational procedure are described. The method has been applied for the analysis of a symmetric and an asymmetric variant of a seven-storey reinforced concrete frame–wall building, as well as for the analysis of a complex asymmetric 21-storey reinforced concrete wall building. The influence of torsion on structural behaviour is discussed. © 1997 by John Wiley & Sons, Ltd.     

A new simplified approach for assessing nonlinear seismic response of plan-asymmetric structures considering soil-structure interaction

An innovative approximate method is presented to consider the plan asymmetry, nonlinear structural behaviour and soil-structure interaction (SSI) effects simultaneously. The proposed method so-called Flexible base 2DMPA (F2MPA) is an extension of 2 degrees of freedom modal pushover analysis (2DMPA) approach to consider foundation flexibility in seismic response analysis of plan asymmetric structures which itself were developed based on Uncoupled Modal Response History Analysis method for inelastic fixed-base asymmetric structures. In F2MPA for each mode shape using 2DMPA procedure, the elastic and inelastic properties of 2DOF modal systems corresponding to the fixed-base structure are initially derived. Then in each time step, displacements and inelastic restoring forces of the superstructure are computed from modal equations of the flexibly-supported structure. In each time step, the nonlinear secant stiffness matrix corresponding to the n-th MDOF modal equations of soil-structure system is updated using the corresponding modal 2DOF system of fixed-base structure. To update the transformed modal stiffness matrix of the SSI system, this matrix is partitioned and it is assumed that the non-linear variation of the superstructure can be estimated from the variation of modal stiffness matrix of the fixed-base structure. Accuracy of the proposed method was verified on an 8-story asymmetric-plan building under different seismic excitations. The results obtained from F2MPA method were compared with those obtained by nonlinear response history analysis of the asymmetric soil-structure system as a reference response. It was shown that the proposed approach could predict the results of the nonlinear time history analysis with a good accuracy. The main advantage of F2MPA is that this method is much less time-consuming and useful for the practical aims such as massive analysis of a nonlinear structure under different records with multiple intensity levels.