不同尺度裂缝对弹性波速度和各向异性影响的实验研究

裂缝广泛分布于地球介质中并且具有多尺度的特点,裂缝尺度对于油气勘探和开发有着重要的意义.本文制作了一组含不同长度裂缝的人工岩样,其中三块含裂缝岩样中的裂缝直径分别为2 mm、3 mm和4 mm,裂缝的厚度都约为0.06 mm,裂缝密度大致相同(分别为4.8%、4.86%和4.86%).在岩样含水的条件下测试不同方向上的纵横波速度,实验结果表明,虽然三块裂缝岩样中的裂缝密度大致相同,但是含不同直径裂缝岩样的纵横波速度存在差异.在各个方向上,含数量众多的小尺度裂缝的岩样中纵横波速度都明显低于含少量的大尺度裂缝的岩样中纵横波速度.尤其是对纵波速度和SV波速度,在不同尺度裂缝岩样中的差异更明显.在含数量多的小尺度裂缝的岩样中纵波各向异性和横波各向异性最高,而含少量的大尺度的裂缝的岩样中的纵波各向异性和横波各向异性较低.实验测量结果与Hudson理论模型预测结果进行了对比分析,结果发现Hudson理论考虑到了裂缝尺度对纵波速度和纵波各向异性的影响,但是忽略了其对横波速度和横波各向异性的影响.     

裂隙张开度对地震波特性影响的模型研究

基于Hudson裂隙理论中等效裂隙模型假设,在均匀介质中嵌入定向排列的薄圆片充填物可构成裂隙介质模型.通过改变充填物薄片的厚度,模拟裂隙的张开度,观测其对纵横波传播的影响.在实验室内用环氧树脂作裂隙模型的基质材料,含硅橡胶的混合低速材料做裂隙充填物.当每个模型中裂隙的直径和个数相等时,仅改变裂隙的厚度,形成了一组相同裂隙密度的裂隙模型.采用超声波脉冲透射法获得了平行和垂直裂隙方向纵横波传播的时间和波形记录.实验表明,在相同裂隙密度条件下,裂隙张开度的变化对纵横波的速度和振幅都有影响,其中纵波振幅的变化比速度变化大得多.横波速度的变化主要反映在慢横波上,振幅的变化快横波比慢横波大.这些特征对地震资料的处理和解释有一定的指导意义.     

裂隙参数对衰减各向异性影响的数值模拟

理论、观测和实验均证实,在地壳和上地幔存在对应力变化敏感的直立裂隙,在整体上呈现方位各向异性.在Hudson裂隙理论基础上,系统全面地数值模拟了裂隙介质几何、物性和弹性波频率等参数对各向异性衰减的影响.结果显示,裂隙密度、裂隙纵横比、泊松比、裂缝填充物、弹性波频率和未破裂岩石母体纵横波速度等对各向异性衰减有着显著影响,...     

岩石的等效孔隙纵横比反演及其应用

通过融合Gassmann方程和由微分等效介质理论建立的干岩石骨架模型--DEM解析模型,本文提出根据纵波(和横波)速度反演岩石等效孔隙纵横比进行储层孔隙结构评价和横波速度预测的方法.首先,利用Gassmann方程和DEM解析模型建立岩石的纵、横波速度与密度、孔隙度、饱和度和矿物组分等各参数之间的关系;其次,将岩石孔隙等效为具有单一纵横比的理想椭球孔,应用非线性全局寻优算法来寻找最佳的等效孔隙纵横比使得理论预测与实际测量的弹性模量之间的误差最小;最后,将反演得到的等效孔隙纵横比代入到Gassmann方程和DEM解析模型中构建横波速度.实验室和井孔测量数据应用表明,反演得到的等效孔隙纵横比可准确反映储层的孔隙结构,对于裂缝型储层如花岗岩,其孔隙纵横比通常小于0.025,而对于孔隙型储层如砂岩,其孔隙纵横比通常大于0.08.只利用纵波与同时利用纵、横波反演得到的孔隙纵横比结果几乎完全一致,而且由纵波构建的横波与实测横波吻合良好,说明本文提出的等效孔隙纵横比反演及其横波速度预测方法是有效的.     

利用含可控裂缝人工岩样研究裂缝密度对各向异性的影响

利用新方法制作出含可控裂缝的双孔隙人工砂岩物理模型,具有与天然岩石更为接近的矿物成分、孔隙结构和胶结方式,其中裂缝密度、裂缝尺寸和裂缝张开度等裂缝参数可以控制以得到实验所需要的裂缝参数,岩样具有真实的孔隙和裂缝空间并可以在不同饱和流体状态下研究流体性质对于裂缝介质性质的影响.本次实验制作出一组具有不同裂缝密度的含裂缝人工岩样,对岩样利用SEM扫描电镜分析可以看到真实的孔隙结构和符合我们要求的裂缝参数,岩样被加工成八面棱柱以测量不同方向上弹性波传播的速度,用0.5 MHz的换能器使用透射法测量在饱和空气和饱和水条件下各个样品不同方向上的纵横波速度,并得出纵横波速度、横波分裂系数和纵横波各向异性强度受裂缝密度和饱和流体的影响.研究发现流体对于纵波速度和纵波各向异性强度的影响较强,而横波速度、横波分裂系数和横波各向异性强度受饱和流体的影响不大,但是对裂缝密度的变化更敏感.     

含裂缝VTI介质的弹性波传播特性研究

有利油气储集的层状沉积地层中广泛存在裂缝,属于含裂缝VTI介质.综合考虑层状介质和裂缝介质的特点,基于几何相似原理,设计并制作了含定向排列裂缝的VTI介质物理模型,实验研究了测量频率、裂缝特征尺寸、裂缝密度对弹性波透射的影响.结果表明,波垂直裂缝面传播时,纵波首波速度随测量频率的增加而线性增大,峰值速度基本不变,单纯由裂缝导致的衰减以良好的乘幂规律降低;纵波波速随裂缝密度、裂缝特征尺寸的增大而线性增大;衰减随裂缝密度增大而增大,随裂缝特征尺寸的增大而减小.当接收探头波长与特征尺寸比为1~12时,纵波首波速度变化显著,处于射线理论与等效介质理论描述的过渡区间.纵横波速比对裂缝特征尺寸变化敏感,可作为典型的裂缝监测参数,也为基于弹性波相应的预测岩石孔隙结构提供了依据.     

基于碳酸盐岩裂缝岩石物理模型的横波速度和各向异性参数预测

高角度缝隙充填的碳酸盐岩储层可以等效为具有水平对称轴的横向各向同性介质.本文提出了适用于裂缝型碳酸盐岩的岩石物理模型构建流程,重点介绍了在碳酸盐岩各向同性背景中,综合利用微小裂隙模型和线性滑动模型添加缝隙系统,并分析了当缝隙充填不同流体时,各向异性参数随纵横波速比的变化特征.同时本文讨论了裂缝密度和缝隙充填流体对地震反射系数的影响,推导了不同类型流体充填时储层反射系数与裂缝密度的近似关系式,阐述了各向异性流体替换理论,最终实现饱含流体碳酸盐岩裂缝储层的纵横波速度和各向异性参数的估测.选取某碳酸盐岩工区A井对该方法进行试算,结果表明基于碳酸盐岩裂缝岩石物理模型估算的纵横波速度值与测井值吻合较好,而且估测所得的各向异性参数值也能够较好地反映出裂缝储层位置.     

三维单斜裂隙介质地震正演模拟

多组任意夹角直立裂隙的排列方式比单组平行排列直立裂隙更具一般性,因此本文基于线性滑动理论和Hudson理论,将上述多组任意夹角直立裂隙介质等效为单斜各向异性介质,给定物性参数计算刚度矩阵,运用交错网格高阶有限差分法求解三维单斜介质弹性波一阶速度-应力方程来模拟弹性波在单斜介质中的传播过程.通过分析不同物性下的波场和共炮点道集,不同偏移距下的方位角道集,说明裂隙物性与波场特征之间的关系,以及其方位特征信息.     

六种不同变质程度煤的纵横波速度特征及其与密度的关系

对采自不同地区和煤矿的六种不同变质程度煤样进行常温常压条件下的超声测量.测量发现:煤的纵波与横波速度均与密度存在良好的线性正相关关系,且沿煤层走向、倾向和垂直煤层层理方向的纵横波速度逐渐降低;走向、倾向和垂向上的纵波速度与同一方向的横波速度也存在良好的线性正相关性;六种煤样三个方向间的速度各向异性一般都大于10%.通过与经典经验公式—Gardner与Castagna公式理论换算值的对比发现:由于煤层的软岩特征,理论换算煤的纵波速度、横波速度与实验室实测值之间存在较大误差.因此,在煤田地震勘探中应使用根据煤的岩石物理测试而形成的关系式.     

一种基于3D复杂介质的弹性建模数值方法

储层中的裂隙会导致介质表现出各向异性.传统等效介质方法假定储层可以被等效成为横向各向同性介质,不适用于复杂裂缝储层的弹性等效建模和各向异性特征分析.本文在前人研究基础上,利用最小二乘方法开展3D复杂裂隙弹性等效数值模拟研究,并与常规等效介质理论方法进行比较,验证数值方法的精确性.数值方法不仅能有效避免Hudson理论和Eshelby-Cheng理论等解析方法在大裂隙密度条件下的参数估计误差,而且兼顾裂隙扰动作用对等效介质参数的影响.数值研究表明,数值方法能够较好地描述复杂裂缝介质的各向异性特征,为复杂裂缝储层地震波各向异性参数反演提供依据.     

Experimental verification of effective anisotropic crack theories in variable crack aspect ratio medium

Physical modelling of cracked/fractured media using downscaled laboratory experiments has been used with great success as a useful alternative for understanding the effect of anisotropy in the hydrocarbon reservoir characterization and in the crustal and mantle seismology. The main goal of this work was to experimentally verify the predictions of effective elastic parameters in anisotropic cracked media by Hudson and Eshelby–Cheng's effective medium models. For this purpose, we carried out ultrasonic measurements on synthetic anisotropic samples with low crack densities and different aspect ratios. Twelve samples were prepared with two different crack densities, 5% and 8%. Three samples for each crack density presented cracks with only one crack aspect ratio, whereas other three samples for each crack density presented cracks with three different aspect ratios in their composition. It results in samples with aspect ratio values varying from 0.13 to 0.26. All the cracked samples were simulated by penny‐shaped rubber inclusions in a homogeneous isotropic matrix made with epoxy resin. Moreover, an isotropic sample for reference was constructed with epoxy resin only. Regarding velocity predictions performed by the theoretical models, Eshelby–Cheng shows a better fit when compared with the experimental results for samples with single and mix crack aspect ratio (for both crack densities). From velocity values, our comparisons were also performed in terms of the ε, γ, and δ parameters (Thomsen parameters). The results show that Eshelby–Cheng effective medium model fits better with the measurements of ε and γ parameters for crack samples with only one type of crack aspect ratio.     

The Effect of Varying Damage History in Crystalline Rocks on the P- and S-Wave Velocity under Hydrostatic Confining Pressure

Cracks play a very important role in many geotechnical issues and in a number of processes in the Earth’s crust. Elastic waves can be used as a remote sensing tool for determining crack density. The effect of varying crack density in crystalline rock on the P- and S-wave velocity and dynamic elastic properties under confining pressure has been quantified. The evolution of P- and S-wave velocity were monitored as a suite of dry Westerly granite samples were taken to 60, 70, 80 and 90 % of the unconfined uniaxial strength of the sample. The damaged samples were then subjected to hydrostatic confining pressure from 2 MPa to 200 MPa to quantify the effect of varying crack density on the P- and S-wave velocity and elastic properties under confining pressure. The opening and propagation of microcracks predominantly parallel to the loading direction during uniaxial loading caused a 0.5 and 6.3 % decrease in the P- and S-wave velocity, respectively. During hydrostatic loading, microcracks are closed at 130 MPa confining pressure. At lower pressures the amount of crack damage in the samples has a small but measureable effect. We observed a systematic 6 and 4 % reduction in P- and S-wave velocity, respectively, due to an increase in the fracture density at 2 MPa confining pressure. The overall reduction in the P- and S-wave velocity decreased to 2 and 1 %, respectively, at 50 MPa. The elastic wave velocities of samples that have a greater amount of microcrack damage are more sensitive to pressure. Effective medium modelling was used to invert elastic wave velocities and infer crack density evolution. Comparing the crack density results with experimental data on Westerly granite samples shows that the effective medium modelling used gave interpretable and reasonable results. Changes in crack density can be interpreted as closure or opening of cracks and crack growth.     

横观各向同性页岩岩石物理模型建立——以龙马溪组页岩为例

在龙马溪页岩微观物性特征分析的基础上,综合利用测井解释、微观测试分析资料,建立了一种适用于龙马溪页岩的横观各向同性岩石物理模型,该模型建模过程：将各向异性SCA和DEM模型联合模拟得到的黏土和干酪根混合物作为背景介质;采用SCA模型对脆性矿物混合物进行模拟,利用各向异性DEM将脆性矿物混合物添加到背景介质;进一步将空孔隙添加到页岩基质,并利用Brown-Korringa模型进行各向异性条件下的流体替换,从而得到横观各向同性页岩岩石物理模型.通过对四川盆地A井龙马溪页岩进行岩石物理建模分析,计算了孔隙纵横比、纵横波速、各向异性系数和弹性参数,检验了模型的准确性.研究结果表明：矿物颗粒和孔隙纵横比是影响模型精度的关键参数,黏土和干酪根颗粒纵横比为0.05,图像识别获得的脆性矿物颗粒纵横比主要分布于0.45~1.0（集中分布于0.5~0.85）,横波波速反演获得的孔隙纵横比主要分布于0.1~0.3（平均值约为0.22）;模型预测和实测纵波波速之间误差为-2.40%~2.21%（平均绝对误差仅1.20%）,预测和实测横波波速之间误差为-1.93%~1.42%（平均绝对误差仅0.64%）,证实了本文模型的准确性和精度.本文模型能够准确计算页岩5个独立的刚度系数,为页岩弹性参数、声波波速、各向异性和脆性分析提供了有效手段,也为后续地球物理和工程地质参数分析提供了重要依据.     

A PHYSICAL MODEL STUDY OF SCATTERING OF WAVES BY ALIGNED CRACKS: COMPARISON BETWEEN EXPERIMENT AND THEORY1

An approximation to plane-wave propagation through a composite material is examined using a physical model with oriented but randomly distributed penny-shaped rubber inclusions within an isotropic epoxy resin matrix. A pulse transmission method is used to determine velocities of shear and compressional waves as a function of angle of incidence and crack density. The experimental and theoretical results of Hudson were compared and limitations within the crack parameters used in this study have been determined. Results from both polarized shear waves (S1, S2) compare favourably with the theory for a composite with up to 7% crack density, but theory and experiment diverge at higher crack densities. On the other hand, compressional-wave velocities at low crack densities (1% and 3%) compare favourably with the theory. It is also shown that the velocity ratio V_p/V_s for two extreme cases, i.e. propagation normal and parallel to the cracks, as a function of crack density and porosity, has a strong directional dependence.     

基于贝叶斯框架的各向异性页岩储层岩石物理反演技术

页岩岩石物理建模旨在建立页岩矿物组分、微观结构、流体填充与岩石弹性参数的关系.对四川盆地龙马溪组页岩进行岩石物理建模研究,针对页岩黏土含量高、层间微裂缝发育等特点,利用Backus平均理论描述页岩黏土矿物弹性参数,利用Chapman理论计算与水平微裂缝有关的VTI各向异性,并利用Bond变换考虑地层倾角的影响.提出以黏土矿物纵、横波速度和孔隙纵横比为拟合参数进行岩石物理反演的方法,并引入贝叶斯框架减小反演的多解性.由已知的黏土矿物纵、横波速度和孔隙纵横比作为先验信息,并以测井纵、横波速度作为约束条件建立反演的目标函数,同时利用粒子群算法进行最优化搜索.计算结果表明,基于先验约束和粒子群算法的反演方法能够较准确地反演黏土矿物的弹性参数、孔隙形态参数以及裂缝密度等参数.计算得到的黏土纵、横波速度较高,并且在一定范围内变化,这可能与龙马溪组页岩的黏土矿物组分中具有较高弹性模量的伊利石含量较高有关,同时也与黏土定向排列等微观物性特征有关.反演得到的裂缝密度与纵波各向异性参数ε呈明显的正相关,而与横波各向异性参数γ相关性较小.另外,页岩各向异性参数与黏土垂向的纵横波速度有较强的相关性.     

水饱和裂纹对地壳岩样中地震波速及各向异性的影响

选择４种地壳岩石样品,经干燥或水饱和处理后在不同围压条件下测量了在其中传播的纵、横波的速度及其各向异性．在大气压条件下低孔隙度(＜１％岩样中,水饱和样品中的纵波速度明显地比干燥样品中的高,但横波速度的差别不大．因为在低孔隙度岩样中纵波速度对孔隙流体的反应比横波速度敏感,可以用泊松比的变化来反映随着围压的增加晶粒间流体对弹性波传播特性的影响．根据实验数据,按Ｏ’Ｃｏｎｎｅｌｌ模型分别计算了干燥和水饱和岩样中的裂纹密度,与通过实测体应变曲线得到的裂纹孔隙度十分吻合．利用横波的速度和偏振特性可以推断岩样中定向排列微裂纹的空间取向情况．研究表明,同时测量在岩样中传播的纵、横波的速度,通过Ｖｐ／Ｖｓ比值可以给出有关颗粒边界流体的证据,也可以估计岩样中的裂纹密度．     

裂缝型储层流体识别方法

裂缝型储层的描述包括预测裂缝分布特征和识别裂隙充填物.依据等效介质理论计算的纵波速度随裂缝密度的增大而减小.正演地震记录显示,裂缝介质含气时反射振幅最大,且变化程度比含油或含水时大.叠前方位AVO反演所得的各向异性梯度Bani与裂缝密度成正比,可用于描述有效裂缝发育强度.对于不同的裂缝密度,各向异性梯度Bani与各向同性梯度Biso的比值I(1)fluid近似为常数,且对流体敏感.经裂缝纵横比和背景介质拉梅常数修正后,流体因子Ifluid既不随纵横比变化,又不受背景介质的影响,是裂缝型储层敏感的流体识别因子.在塔里木盆地塔北哈拉哈塘地区热瓦普区块碳酸盐岩储层裂缝发育区域,运用该参数在井点处的流体识别效果与钻井结果一致.     

有效应力变化对致密砂岩孔隙结构及弹性波响应的影响规律

致密砂岩气藏具有裂缝发育和有效应力高的特征,研究不同有效压力下孔、裂隙介质地震波传播特征,有利于地震解释与地下储层的识别.但是前人的研究较少考虑岩石内部微观孔隙结构特征与孔隙、裂隙间流体流动的关系.本文首先通过选取四川盆地典型致密砂岩岩样,在不同有效压力下对岩石样本进行超声波实验测量.然后基于实验测得的纵、横波速度进行裂隙参数反演,得到不同有效压力下致密砂岩样本的裂隙孔隙度.再将裂隙孔隙度和样本岩石物理参数代入双重孔隙介质模型,模拟得到不同有效压力下饱水致密砂岩样本纵横波速度频散和衰减的变化规律.结果表明模型预测的速度频散曲线与纵波速度实验测量结果能够较好的吻合.最后统计分析了致密砂岩裂隙参数,得到了致密砂岩储层裂隙参数随有效压力及孔隙度变化特征.依据实际岩石物理参数建立模型,其裂隙参数三维拟合结果能够较好描述致密砂岩裂隙结构与孔隙度、应力的关联,可为实际地震勘探中预测储层裂缝性质提供基础依据.     

A physical model for shear-wave velocity prediction1

The clay-sand mixture model of Xu and White is shown to simulate observed relationships between S-wave velocity (or transit time), porosity and clay content. In general, neither S-wave velocity nor S-wave transit time is a linear function of porosity and clay content. For practical purposes, clay content is approximated by shale volume in well-log applications. In principle, the model can predict S-wave velocity from lithology and any pair of P-wave velocity, porosity and shale volume. Although the predictions should be the same if all measurements are error free, comparison of predictions with laboratory and logging measurements show that predictions using P-wave velocity are the most reliable. The robust relationship between S- and P-wave velocities is due to the fact that both are similarly affected by porosity, clay content and lithology. Moreover, errors in the measured P-wave velocity are normally smaller than those in porosity and shale volume, both of which are subject to errors introduced by imperfect models and imperfect parameters when estimated from logs. Because the model evaluates the bulk and shear moduli of the dry rock frame by a combination of Kuster and Toksöz’ theory and differential effective medium theory, using pore aspect ratios to characterize the compliances of the sand and clay components, the relationship between P- and S-wave velocities is explicit and consistent. Consequently the model sidesteps problems and assumptions that arise from the lack of knowledge of these moduli when applying Gassmann's theory to this relationship, making it a very flexible tool for investigating how the v_P-v_s relationship is affected by lithology, porosity, clay content and water saturation. Numerical results from the model are confirmed by laboratory and logging data and demonstrate, for example, how the presence of gas has a more pronounced effect on P-wave velocity in shaly sands than in less compliant cleaner sandstones.