客运专线桥梁基于性能的抗震设计研究

从基于性能的抗震设计理念出发,给出了客运专线桥梁结构的性能目标及各性能水准下的桥墩地震破损描述,明确并量化了桥墩各抗震性能目标的验算内容。给出了小震不坏及可控制中震损伤的验算方法,简化能力谱法计算位移延性系数,指出了大震时最大位移验算的不足,讨论了桥墩大震时地震损伤指数的计算与验算,通过算例详细介绍了基于性能的抗震设计方法与过程。     

地震动反应谱与RC框架结构地震响应相关性分析

弹塑性时程分析一般用来评估和验算结构抗震性能,如何选取合适的输入地震动是其中关键工作之一。为给结构弹塑性时程分析选取地震动提供合理的参考参数,本文讨论了地震动反应谱参数与结构地震响应之间的相关性。首先建立了6层和7层两个钢筋混凝土(RC)框架结构数值模型,分别对两个结构进行了大量地震动作用下的时程反应分析,并考察了地震反应特点;然后将结构地震响应与地震动反应谱参数建立关系并进行了相关性分析。结果表明:对RC框架而言,结构地震响应与弹性谱参数相关性较小,与等强度反应谱相关性随标准屈服强度降低而增大,与等延性反应谱相关性随延性增大而增大,而与地震动输入能量谱在标准屈服强度较小时相关性最大。建议RC框架结构在进行地震反应时程分析时,可以参考地震动的弹塑性输入能量谱、等强度速度谱和等延性加速度或位移谱,以选取引起结构不同地震反应水平的输入地震动。本文结果和结论可供结构弹塑性时程分析选取合适的输入地震动参考。     

屈曲约束支撑半刚性连接框架弹塑性地震位移简化计算

研究屈曲约束支撑半刚性连接框架弹塑性位移计算方法,为这种结构抗震设计提供依据.推导了屈曲约束支撑半刚性连接框架结构侧移刚度计算方法,通过计算屈曲约束支撑和半刚性连接在罕遇地震作用下的有效阻尼比,修正弹性设计反应谱,再利用修正后的设计反应谱进行结构弹塑性层间位移简化计算.通过与弹塑性时程分析对提出的计算方法进行验证.基于有效阻尼比的思想给出的弹塑性位移的简化计算方法可进行屈曲约束支撑半刚性连接框架罕遇地震下的抗震设计.     

考虑场地类别与设计分组的延性需求谱和弹塑性位移反应谱

非线性反应谱是基于性能的抗震设计理论中亟待解决的基础性课题之一。本文将四种场地类别上的641条地震记录,按我国现行抗震规范设计分组的要求分为12组,对大量具有不同屈服强度系数的单自由度体系作了弹塑性时程分析。研究了结构强度水平、周期、场地类别以及设计分组等因素对延性需求的影响。结果表明,在给定屈服强度水平下结构的延性需求强烈地依赖于场地条件、设计分组等因素。对于短周期结构,延性需求随场地土变软而增大,同类场地随设计分组特征周期增大而增大。通过非线性回归分析,建立了与场地类别、设计分组相对应的延性需求谱μ-ξy-T的计算公式。在此公式的基础上,结合现阶段抗震设计规范构建了弹塑性位移反应谱,可用于结构弹塑性位移需求的简化计算,同时讨论了弹塑性位移反应谱的基本特点。     

基于规范谱的隔震结构非弹性位移设计谱研究

随着基于性能抗震设计理论研究的兴起,位移反应谱的研究逐渐受到重视。对于具有长周期特性的隔震结构,其位移响应相对于加速度响应更加显著,有必要对隔震结构的位移响应进行研究。选取特定震源机制、场地条件、震中距和震级的60条地震记录作为外部激励,利用MATLAB编程并计算得到隔震结构的位移反应谱,通过与规范反应谱进行对比分析,探讨利用现行规范谱来预测隔震结构位移需求时存在的一些问题。考虑隔震支座力学参数、地震动特性等因素对位移反应谱的影响,采用标准化和平均化的方式研究位移反应谱的特征,以Eurocode8规范给出的弹性位移反应谱为基础,通过数值拟合方法建立隔震结构非弹性位移设计谱,用于预测隔震层的最大位移需求,快速确定支座类型,极大简化隔震结构设计流程。     

钢框架结构直接基于位移抗震性能设计的非迭代法

为使直接基于位移的抗震性能设计方法更加简便准确,本文采用一种直接基于位移的非迭代抗震设计方法对钢框架结构进行设计。该方法首先考虑结构的非弹性反应确定等效弹性反应谱和弹塑性反应谱,并建立了使用Newmark-Hall变形折减系数的能力谱的明确表达式。采用能力-需求图方法,确定了结构需要的目标位移与延性、谱位移和谱加速度之间关系的明确表示式,得到结构的刚度和设计基底剪力,进而确定构件截面,完成结构设计。对五层两跨平面钢框架结构进行了直接基于位移的抗震性能设计,设计过程简便,无需迭代程序,不需画出反应谱,通过时程分析验证了设计结果的精确性。本文研究表明:直接基于位移的非迭代抗震设计方法是一种简便、高效、精确的抗震性能设计方法。     

交错桁架多层钢结构推倒分析方法研究

随着基于性能的抗震设计思想的发展,推倒分析开始成为罕遇地震下多、高层结构抗震设计的有力工具。本文以交错桁架多层钢结构为例,采用推倒分析对其在E l Centro波作用下的地震反应进行研究,分别采用位移系数法和能力谱法确定结构目标位移,同时进行结构在相同地震动下的弹塑性时程分析。研究表明,推倒分析能准确地评价交错桁架多层钢结构的抗震性能,采用位移系数法和能力谱法确定的结构顶点侧移均与弹塑性时程分析吻合较好,对层间位移及塑性铰分布的预测,能力谱法比位移系数法更为准确。     

损伤谱在结构抗震性能评估中的应用

改进能力谱法可以较好地评估结构抗震性能,在工程中得到了广泛的应用.本文在此基础上指出,由改进能力谱方法求得的延性是结构的延性需求,并不是结构的实际延性能力,不能以此代表结构在罕遇地震作用下的实际抗震能力.其次,基于弹塑性损伤反应谱(简称"RD谱"),结合模态Pushover分析,提出了基于RD谱的能力谱分析方法,通过R...     

基于公路工程规范地震需求谱研究

从解决桥梁结构的实际问题出发,根据桥梁结构的抗震能力及计力法的需要,由于强度折减系数R与延性系数μ的关系建立弹塑性反应谱的原理,建立了基于《公路工程抗震设计规范》(JTJ 004-89)给出的弹性反应谱的非弹性地震需求谱,为桥梁结构抗震性能评价的研究提供参考意见。     

延性需求谱在基于性能的抗震设计中的应用

基于性能的抗震设计理论涉及如何简便而合理地确定结构在指定强度地震下的弹塑性位移需求。本文给出了利用延性需求谱求解结构位移需求的一般步骤:借助模态Pushover分析将多自由度体系分解为几个非线性单自由度体系,以考虑各阶振型的影响;利用延性需求谱计算对应模态的等效单自由度体系的延性及位移需求,并以一定方式组合转化为多自由度体系位移需求。最后,通过算例分析表明:利用延性需求谱求解结构位移需求是一种具有一定精度可为工程接受的简便方法,在基于性能的抗震设计中具有较好的应用前景。     

几种push-over分析方法对比研究

Push-over方法是一种静力非线性计算方法，是近年来在国内外得到广泛研究应用的用于评价结构抗震能力的新方法。采用这种方法计算结构的弹塑性地震反应将会逐渐为广大的工程设计人员所接受，但目前对于这种用静力的方法去预测结构的动力反应，其可靠性如何一直是许多学者所关注的，而且对于现有的几种方法的优劣也没有给出综合的评价。本文在国内外有关理论和方法的基础上，对几种push-over分析方法进行了简要评述，并通过分析计算对其中有代表性的能力谱方法、位移影响系数法和适应谱push-over方法进行了详细的对比研究。指出了其中存在的问题，试图寻找并推荐一种比较好的方法。结果能够实现这一目标，对于push-over方法的发展将会有一定的推动作用。     

Comparison of displacement coefficient method and capacity spectrum method with experimental results of RC columns

For the performance‐based seismic design of buildings, both the displacement coefficient method used by FEMA‐273 and the capacity spectrum method adopted by ATC‐40 are non‐linear static procedures. The pushover curves of structures need to be established during processing of these two methods. They are applied to evaluation and rehabilitation of existing structures. This paper is concerned with experimental studies on the accuracy of both methods. Through carrying out the pseudo‐dynamic tests, cyclic loading tests and pushover tests on three reinforced concrete (RC) columns, the maximum inelastic deformation demands (target displacements) determined by the coefficient method of FEMA‐273 and the capacity spectrum method of ATC‐40 are compared. In addition, a modified capacity spectrum method which is based on the use of inelastic design response spectra is also included in this study. It is shown from the test specimens that the coefficient method overestimates the peak test displacements with an average error of +28% while the capacity spectrum method underestimates them with an average error of ‐20%. If the Kowalsky hysteretic damping model is used in the capacity spectrum method instead of the original damping model, the average errors become ‐11% by ignoring the effect of stiffness degrading and ‐1.2% by slightly including the effect of stiffness degrading. Furthermore, if the Newmark–Hall inelastic design spectrum is implemented in the capacity spectrum method instead of the elastic design spectrum, the average error decreases to ‐6.6% which undervalues, but is close to, the experimental results. Copyright © 2003 John Wiley & Sons, Ltd.     

基于能力谱法的SSI体系抗震pushover分析方法

本文首先经过2次等效将土与结构相互作用的多自由度体系等效为单自由度体系,并给出了修正反应谱和等价能力谱的确定方法,进而提出了基于能力谱法考虑土与结构动力相互作用(SSI)效应的结构体系pushover分析方法(SSIPA);然后对3种不同高度考虑SSI效应的结构体系在5条地震动作用下采用本文提出的方法进行了算例分析,将结果与非线性时程分析的结果进行了比较,研究了本方法的适用性和准确性;最后,与建筑抗震设计规范的设计反应谱相结合,对9层考虑SSI效应的钢结构用本文提出的方法进行了弹塑性地震反应分析,根据我国抗震设计规范的规定进行抗震性能的评估验证了本方法的可行性。     

Pushover analysis procedure for systems considering SSI effects based on capacity spectrum method

This paper presents a new procedure to transform an SSI system into an equivalent SDOF system using twice equivalence. A pushover analysis procedure based on the capacity spectrum method for buildings with SSI effects （PASSI） is then established based on the equivalent SDOF system, and the modified response spectrum and equivalent capacity spectrum are obtained. Furthermore, the approximate formulas to obtain the dynamic stiffness of foundations are suggested. Three steel buildings with different story heights （3, 9 and 20） including SSI effects are analyzed under two far-field and two near-field historical records and an artificial seismic time history using the two PASSI procedures and the nonlinear response history analysis （NLhRHA） method. The results are compared and discussed. Finally, combined with seismic design response spectrum, the nonlinear seismic response of a 9-story building with SSI effects is analyzed using the PASSI procedures, and its seismic performance is evaluated according to the Chinese ＇Code for Seismic Design of Buildings. The feasibility of the proposed procedure is verified.     

应用弹塑性反应谱对IDA方法的改进研究

针对传统IDA方法中结构的加速度反应远高于SPO分析结果的现象,采用弹塑性反应谱作为IDA的烈度度量,同时给出随地震烈度改变而不断变化的屈服强度系数,提出了改进的IDA方法,更有效地考虑了结构的非线性地震反应特征。实际工程分析表明,改进的IDA方法能够体现结构的非线性受力反应,同时兼顾结构的动力反应特征,与SPO曲线和由规范计算得到的结构承载力有更好的可比较性。     

Capacity spectrum method based on inelastic demand spectra

By means of a graphical procedure, the capacity spectrum method compares the capacity of a structure with the demands of earthquake ground motion on it. In the present version of the method, highly damped elastic spectra have been used to determine seismic demand. A more straightforward approach for the determination of seismic demand is based on the use of the inelastic strength and displacement spectra which can be obtained directly by time-history analyses of inelastic SDOF systems, or indirectly from elastic spectra. The advantages of the two approaches (i.e. the visual representation of the capacity spectrum method and the superior physical basis of inelastic demand spectra) can be combined. In this paper, the idea of using inelastic demand spectra within the capacity spectrum method has been elaborated and is presented in an easy to use format. The approach represents the so-called N2 method formulated in the format of the capacity spectrum method. By reversing the procedure, a direct displacement-based design can be performed. The application of the modified capacity spectrum method is illustrated by means of two examples. Copyright © 1999 John Wiley & Sons, Ltd.     

基于模拟退火算法的设计反应谱标定方法

反应谱的标定是抗震设计的基础工作之一,模拟退火算法是基于模拟固体退火过程而提出的多参数优化组合方法。本文提出将模拟退火算法应用于设计反应谱的标定,并概述了模拟退火算法的基本原理及特点,介绍了运用MATLAB基于模拟退火算法对反应谱进行标定的过程。检验了将模拟退火算法应用于场地相关谱标定的可行性和合理性,给出了将其应用于工程场地地震安全性评价中设计反应谱标定实例。通过检验和实例分析可以看出,基于模拟退火算法的反应谱标定方法所给出的设计反应谱谱形真实地反映了原地震反应谱的特征,较客观的反映了场地相关反应谱的峰值和周期特征。     

Direct design method based on seismic capacity redundancy for structures with metal yielding dampers

In this study, a direct static design method for structures with metal yielding dampers is proposed based on a new design target called the seismic capacity redundancy indicator (SCRI). The proposed method is applicable to the design of elastic‐plastic damped structures by considering the influence of damper on different structural performance indicators separately without the need for iteration or nonlinear dynamic analysis. The SCRI—a quantitative measure of the seismic capacity redundancy—is defined as the ratio of the seismic demand required by the target performance limit to the design seismic demand. Changes in the structural SCRI are correlated with the parameters of the supplemental dampers so that the dampers can be directly designed according to a given target SCRI. The proposed method is illustrated through application to a 12‐story reinforced‐concrete frame, and increment dynamic analysis is performed to verify the effectiveness of the proposed method. The seismic intensity corresponding to the target structural performance limit is regarded as a measure of the structural seismic capacity. The required seismic intensity increases after the structure is equipped with the designed metal yielding dampers according to the expected SCRI. It is concluded that the proposed method is easy to implement and feasible for performance‐based design of metal yielding dampers.     

Accuracy of nonlinear static procedures for the seismic assessment of shear critical structures

The nonlinear behavior of reinforced concrete (RC) members represents a key issue in the seismic performance assessment of structures. Many structures constructed in the 1980s or earlier were designed based on force limits; thus they often exhibit brittle failure modes, strength and stiffness degradation, and severe pinching effects. Field surveys and experimental evidence have demonstrated that such inelastic responses affect the global behavior of RC structural systems. Efforts have been made to consider the degrading stiffness and strength in the simplified nonlinear static procedures commonly adopted by practitioners. This paper investigates the accuracy of such procedures for the seismic performance assessment of RC structural systems. Refined finite element models of a shear critical bridge bent and a flexure‐critical bridge pier are used as reference models. The numerical models are validated against experimental results and used to evaluate the inelastic dynamic response of the structures subjected to earthquake ground motions with increasing amplitude. The maximum response from the refined numerical models is compared against the results from the simplified static procedures, namely modified capacity spectrum method and coefficient method in FEMA‐440. The accuracy of the static procedures in estimating the displacement demand of a flexure‐critical system and shear‐critical system is discussed in detail. Copyright © 2015 John Wiley & Sons, Ltd.