土钉支护抗震性能的振动台试验研究

为研究土钉支护结构体系的抗震性能,设计并完成了土钉支护边坡1：12比尺的振动台试验,研究了土钉支护边坡的动力反应特征和规律。结果表明：土钉支护边坡坡面的最大变形主要发生在边坡坡腹处,坡顶与坡趾的变形相对较小;增大土钉倾角会增大边坡的侧向位移,增加土钉长度以及减小土钉间距则会减小边坡侧向位移;土钉支护最大作用带基本位于土钉支护区的中前部,呈折线形,与计算假设的圆弧形不同,而且该作用带与滑裂面的位置并不相同;边坡土体中部和下部的加速度放大系数较小而且比较接近,边坡上部土体的加速度放大系数则较大。     

基于渗流-应力耦合分析的野鸡尾尾矿坝稳定性研究

基于渗流场与应力场耦合机理,对柿竹园野鸡尾尾矿坝进行稳定性研究。研究渗流-应力的耦合效应,提出了渗流-应力耦合以及渗流体积力计算的实施方案;建立二维的有限元渗流-应力耦合计算模型,分析了考虑耦合效应时的尾矿坝渗流场、位移场、应力场;最终分析了不同耦合关系对于渗流量、位移场、等效渗透集中力以及应力场的影响。研究结果表明：当前水力条件下,尾矿坝稳定性良好;尾矿坝主要受水平渗透力作用,初期坝坝顶、坝脚以及坝底等处应力集中;尾矿坝的渗流-应力作用不容忽视,不同的耦合关系对于x方向位移、渗透力的预测影响巨大;考虑渗流-应力耦合关系得到的主应力、剪应力以及竖向位移,比不考虑耦合效应时大。     

水深对水下地基场地地震动影响的时域分析

利用地震波斜入射下水下地基场地地震动分析的一维化时域算法,推导了平面P波入射下,水下地基场地的位移、加速度和应力表达式,重点分析了水深变化对位移峰值、加速度峰值、剪应力峰值和孔隙水压力峰值沿土层深度的分布规律。数值结果表明:同一土层深度处,当水深不超过1倍的土厚时,竖向位移峰值随水深的增大而增大;当水深超过1倍的土厚时,竖向位移峰值随水深的增大而减小。水平位移峰值与水深的关系基本上与竖向位移峰值相反。同一水深下,竖向位移峰值沿土深不断减小,水平位移峰值呈先减小后增加的趋势。同一水深下,竖向加速度峰值沿土深是一个不断减小的过程,水平位移峰值是一个反复增大和减小的过程。在0.75倍的土厚到基岩的范围外,水深对剪应力峰值的影响均较小。孔隙水压力峰值沿土深的分布大致是先减小再增加最后减小。     

辽宁营口沿海地区某深基坑工程数值模拟的分析

软土地区基坑开挖产生大量的支护结构变形和周围土体变形,通过Midas有限元分析软件对营口某深基坑工程进行数值模拟,结合工程实例监测数据验证数值模拟计算结果的准确性。通过分析数值模拟各节点位移数据,总结双排桩支护结构和型钢水泥土墙支护结构对应的挡墙顶部位移及周围土体沉降位移的变化规律,分析发现:1基坑工程变形均存在空间效应,但基坑工程开挖深度不大时,空间效应并不明显;2基坑支护挡墙变形与结构抗弯刚度和开挖深度有关,增加开挖深度或降低结构刚度均导致基坑变形的增加;3锚索结构对于控制基坑变形的效果明显,在今后的工作中应针对不同的工程情况,灵活运用,充分发挥锚索结构的降低变形能力。     

有限元分析在深基坑开挖中的应用及对邻近地铁隧道的影响分析

深基坑工程涉及的土质条件及地下水条件复杂多变,基坑尺寸及支护形式繁多,众多不利因素综合作用导致了深基坑工程在开挖过程中产生的变形值难以预测。利用有限元分析软件对辽宁地区某深基坑工程实例进行数值模拟,围绕工程实例放坡结合桩锚支护挡墙在地铁隧道影响下的结构水平位移,支护挡墙外侧不同距离处的土体深层水平位移以及地铁隧道在开挖过程中的结构位移等变化规律展开研究工作。     

桩靴连续贯入过程的动态模拟方法研究

采用CEL方法(耦合的欧拉-拉格朗日分析法)对比研究桩靴下沉速度不同对计算结果的影响,分析不同桩靴下沉速度下附近桩基础的响应,研究质量放大方法的适用性。结果表明:无桩时桩靴贯入速度不同对土体阻力影响较小,土体的破坏形态和剪应力水平略有不同;桩靴贯入速度对桩身水平位移影响较小,桩靴贯入速度越大,桩身最大应力越小;质量放大系数的增加对桩身最大位移的影响较小,但对桩身最大应力有较大影响,因此建议谨慎使用质量放大方法。     

自由场典型液化特征数值模拟试验

应用FLAOD实现自由场液化数值模拟试验.试验结果验证了砂土液化典型特征:超静孔隙水压升高,有效应力降低,体积压缩积累增大.证实了液化的隔振作用:砂土在液化状态变为流体,不能传递剪力,液化时砂土位移、速度、加速度振幅显著降低,剪应力降低,动水向上渗流,土体向下沉降,水平残留不可恢复位移.球压应力、有效压应力、动水压力满...     

基于流固耦合两相介质动力模型的饱和土体—地下结构体系地震反应研究

基于ABAQUS有限元软件平台,应用流固耦合两相介质动力模型孔压单元模拟场地饱和土体,进行了饱和土体-地下结构地震反应的计算研究。结果表明：在地震输入的最后时刻结构的两侧底角区域应力值最大;土体的孔隙压力和竖向位移主要集中在结构下方的区域,结构两侧土体的孔压与竖向位移呈对称分布;场地土体的竖向位移随深度的增加逐渐减小;体系最大地震反应出现的时刻对应于输入地震动的最大加速度出现的时刻。表明了流固耦合两相介质动力模型孔压单元在饱和土体-地下结构体系地震反应研究中的有效性。     

竖向地震动对大跨度高断面Y形柱地铁车站地震响应分析研究

以北京地铁6号线新华大街站公共区Y型柱地铁车站为工程背景,利用FLAC3D有限差分程序数值模拟分析,研究超浅埋大跨度、高断面、Y形柱地铁车站结构分别在仅输入水平向地震动和同时输入水平向与竖向地震动情况下的地震响应特性。结果表明:(1)与仅输入单向地震动相比,双向地震动耦合作用下车站各测点的峰值加速度和应力值均增大,而相对水平位移减小,且随着输入地震动强度的增加,竖向地震动影响率呈递减趋势;(2)双向地震动作用下,同一工况Y形柱叉支处各测点的竖向位移明显增大,且各测点的竖向位移值较为均匀,而单向水平地震动作用下各测点竖向位移差异较大;(3)与单向水平地震动相比,竖向地震动的输入对各测点间的水平方向地震动特性规律影响较小。     

基坑被动区加固对基坑支护体系变形和桩后土体沉降的影响

深厚软土地区基坑常用基坑被动区加固的方法来控制支护体系变形.以珠海深厚软土地区某基坑工程为例,采用FLAC3D软件,建立了基坑工程分析模型,计算分析了被动区土体加固深度及加固宽度对基坑支护体系变形和桩后土体沉降的影响.计算结果表明,随着被动区加固深度和加固宽度的增加,桩身位移量和桩后土体沉降量均逐渐减小;桩身位移量和土体沉降量的减幅随着加固深度和加固宽度的增加而逐渐减小,故加固区存在最优加固深度和加固宽度,分别为10 m和12 m左右;桩后土体沉降影响区域范围为2 H,坑外地表最大沉降点在距围护桩0.5 H处.     

Incipient motion of cohesionless sediments on riverbanks with ground water injection

This study investigates the influence of ground water injection on the initial movement of non-cohesive sediment particles on a riverbank slope analytically and experimentally.By including the hydrauli...     

CFG桩基坑内施工对基坑周围环境稳定性的影响

在地下工程中,由于天然地基承载力不足,带有地下室的主体结构采用CFG桩复合地基。因为CFG桩长螺旋钻施工设备限制,地下室底板下的CFG桩必须在深基坑开挖一部分后进行施工。在某深基坑工程中,随着CFG桩的施工,基坑周围地表出现明显开裂现象。为探究其原因,结合该基坑工程实例,利用FLAC3D软件,通过数值模拟分析考虑渗流作用下CFG桩基坑内施工对基坑周围地表变形的影响规律,并把计算结果同实际监测数据进行对比分析。研究结果表明:CFG桩在部分开挖基坑内施工的快速取土作用对基坑内被动土压力区产生扰动,削弱原有的被动土压力,导致基坑周围土体变形。基坑周围地表变形的影响范围超出2倍基坑深度的监测范围,因此,部分开挖基坑内施工CFG桩的基坑工程周围环境的监测范围应在满足国家规范要求的基础上适当增大。根据计算结果建议类似基坑工程监测范围距基坑边缘的距离采用基坑开挖深度与基坑底面以下CFG桩长之和。类似基坑工程设计应加大支护结构和止水帷幕深度,施工时从基坑内部向外部隔桩跳打,并适当增加工期,将有利于降低由于CFG桩基坑内施工对基坑周围土体的影响。     

渗透固结方法分类的探讨

在分析饱和软土地基不同排水固结处理方法的基础上,将饱和软土渗透固结按其作用机理的不同区分为压缩型固结和渗透力型固结;渗透力型固结又分为减压型和加压型两种形式,将真空预压归类于减压型渗透力固结。提出了超稳定渗流孔隙水压力的概念,得出了渗透力型固结的过程就是超稳定渗流孔隙水压力逐渐转化为有效应力的过程的结论;建立了渗透力型固结沉降计算的简化方法。并对渗透固结处理软土地基的若干问题进行了分析和讨论。     

地下水渗流沉降的三维耦合模型及程序的研制

研制可合理模拟预测基坑降水过程中引起地面沉降的计算机程序,并提出最优化降水方案。基于三维全耦合数值模型,笔者开发了GWS软件。GWS软件是以比奥固结理论为基础,将土体的非线性特征及土的渗透性随应力状态的动态变化考虑进去,通过耦合地下水渗流场和土体应力场进行模拟预测基坑降水过程中渗流场及地面沉降的变化。以一个实际基坑降水工程为例,经GWS软件计算得出5口井联合抽水方案,后续工程证明此方案正确、可靠。以三维全耦合数值理论为基础的GWS软件,可以为基坑降水工程引起的地下水渗流场变化及地面沉降量提供可靠的预测。     

考虑卸荷变形模量的坑底回弹变形计算方法

针对基坑开挖卸荷导致坑底土体回弹变形问题,考虑开挖卸荷过程中土体弹性模量随着卸荷应力路径变化的特征,推导在卸荷应力路径作用下土体变形模量的计算公式,考虑基坑的开挖为地表以下基坑开挖面处应力的变化,基于Mindlin应力解计算矩形基坑开挖卸荷引起的坑底土体附加应力,采用分层总和法计算基坑开挖引起的坑底土体的回弹变形,结合已有文献中的工程实例,采用该方法计算开挖引起的坑底隆起变形,并与实际监测数据对比分析表明,该方法能够有效预测基坑开挖引起的坑底隆起变形,能够作为基坑开挖坑底隆起变形的一种有效预测方法。     

Deep heterogeneity of the stress state in the horizontal shear zones

The formation structures of brittle destruction in a rock layer above an active strike-slip fault in the crystalline basement is studied. The problem is analyzed from the standpoint of loading history, when after the stage of pure gravitational loading, an additional strain state of uniform horizontal shear of both the layer and underlying basement develops, which is further followed by a vertically nonuniform shear caused by the activation of the deep fault. For the studied object, irreversible fracture deformations on macro- and microlevels arise as early as the initial stage of loading under the action of gravitational stresses. These deformations continue evolving on the megascopic level in the course of horizontal shearing that is quasi-uniform both along the depth and laterally. The final formation of the structural ensemble occurs after a long stage of horizontal displacement of the blocks of the crystalline basement—the stage of localized shear. The theoretical analysis of the evolution of the stress state and morphology of the failure structures established the presence of numerous fractures with the normal dip-slip components in the intermediate-depth part of the rock mass, which are formed at the stages of uniform and localized horizontal shearing. The fractures with a strike-slip component mainly arise in the upper and near-axial deep parts of the section.     

In-plane soil–structure interaction in layered,fluid-saturated,poroelastic half-space I: Structural response

Linear in-plane soil–structure interaction in two dimensions (2D) is studied in fluid-saturated, poroelastic, layered half-space using the Indirect Boundary Element Method (IBEM). The structure is a shear wall supported by a rigid embedded foundation. Exact stiffness matrices for the soil layer and half-space, and Green׳s functions of uniformly distributed loads and pore pressure on an inclined line are derived. Results of the system response in the frequency domain are presented for the special case of single soil layer over bedrock, semi-circular foundation and zero seepage force. The effects of water saturation, soil porosity, depth of soil layer, rigidity contrast between layer and bedrock are investigated in the frequency domain for incident plane P- and SV waves. The results suggest that water saturation may cause increase of the system frequency by more than 10%.     

沙土在孔隙水注入实验中渗透剪切破坏

前人曾指出液化后伴随着超孔隙水压重新分配的渗透会引起流体破坏的可能性。为了研究这一现象,利用实验室三轴试验将孔隙水注入土壤检测了土壤的渗透剪切破坏。该实验是在各项异性的固结作用后保持差应力,使用孔隙水控制装置在体积不变的应变控制条件下将孔隙水注入。实验中所用的材料是在1995年神户地震时被液化的常规洁净细砂和风化的花岗岩土壤。本文以实验结果为基础,讨论了由孔隙水注入引起的渗透剪切破坏判据和导致后液化行为的剪切应变发展特征。     

Monitoring and modelling of pore water pressure changes and riverbank stability during flow events

Pore water pressures (positive and negative) were monitored for four years (1996–1999) using a series of tensiometer‐piezometers at increasing depths in a riverbank of the Sieve River, Tuscany (central Italy), with the overall objective of investigating pore pressure changes in response to ?ow events and their effects on bank stability. The saturated/unsaturated ?ow was modelled using a ?nite element seepage analysis, for the main ?ow events occurring during the four‐year monitoring period. Modelling results were validated by comparing measured with computed pore water pressure values for a series of representative events. Riverbank stability analysis was conducted by applying the limit equilibrium method (Morgenstern‐Price), using pore water pressure distributions obtained by the seepage analysis. The simulation of the 14 December 1996 event, during which a bank failure occurred, is reported in detail to illustrate the relations between the water table and river stage during the various phases of the hydrograph and their effects on bank stability. The simulation, according to monitored data, shows that the failure occurred three hours after the peak stage, during the inversion of ?ow (from the bank towards the river). A relatively limited development of positive pore pressures, reducing the effective stress and annulling the shear strength term due to the matric suction, and the sudden loss of the con?ning pressure of the river during the initial drawdown were responsible for triggering the mass failure. Results deriving from the seepage and stability analysis of nine selected ?ow events were then used to investigate the role of the ?ow event characteristics (in terms of peak stages and hydrograph characteristics) and of changes in bank geometry. Besides the peak river stage, which mainly controls the occurrence of conditions of instability, an important role is played by the hydrograph characteristics, in particular by the presence of one or more minor peaks in the river stage preceding the main one. Copyright © 2004 John Wiley & Sons, Ltd.