陆面微波比辐射率的卫星观测研究进展

复杂多变的陆地表微波比辐射率,造成陆面上星载微波观测反演大气参数较为困难,也使得许多卫星微波资料不易同化应用到数值模式,因此迫切需要提供准确可靠的陆面微波地表比辐射率信息.随着卫星观测技术的迅速发展,利用丰富的星载被动微波观测直接反演陆面微波比辐射率成为一种主要手段.国外针对星载微波成像仪和微波垂直探测器开展较为系统的陆面微波比辐射率研究,建立不同类型的地表比辐射率反演方法,开发地表比辐射率参数化方法并应用于辐射资料同化.对于卫星观测反演陆面微波比辐射率存在的问题,开展了评估分析和方法订正.国内利用卫星观测也开展了一些陆面微波比辐射率研究工作,尚需要系统、综合的提炼.对于地表特征复杂的中国地区,还需要评估认识不同陆面微波比辐射率反演方法在我国适用情况,需要增强陆面微波比辐射率数据质量的认识以及业务应用.     

遥感与实测地表温度的对比分析及在地震研究中的意义

伴随着空间观测技术的发展,卫星热红外遥感在地震领域受到越来越多的关注,同时存在许多基础性工作亟待完善.本文以由卫星遥感影像与实际测量两种不同方法获取的地表温度为基础,选取2006年3月～2008年2月近2年的数据,进行遥感与实测地表温度之间的对比研究.分析结果表明遥感与实测地表温度之间:夜间差值比白天要小,白天的相关性...     

GMS 5资料反演地表温度的一个修正算法

本文研究发展利用GMS 5/VISSR每小时卫星观测资料反演地表温度的方法,首先利用时空判断法进行云检测寻找晴空像元,然后从辐射传输方程出发,由实时探空资料求取大气上行、下行辐射率及大气透过率,根据由AVHRR NDVI导出的地表比辐射率,用单时相双光谱分裂窗法反演得到地表温度.比较反演结果与54511站及其他中国基准站2000年地面0cm地表温度实测值,相对于国际上其他经验公式而言,本文算法在精度上有所提高.敏感性分析试验着重于大气衰减的影响.基于本文算法,给出了内蒙中东部地区地表温度连续4天的变化实例以及东亚部分陆地“纯晴天”地表温度图.     

一个针对被动微波AMSR-E数据反演地表温度的物理统计算法

用MODIS的地表温度产品和AMSR-E不同通道之间的亮度温度回归分析表明用89GHzV 做地表温度反演主通道的精度最高. 用AIEM模型模拟表明, 土壤粗糙度和土壤水分变化引起土壤辐射率变化可以通过不同极化波段的差值得到有效的消除, 从而克服了被动微波反演地表温度中辐射率不稳定的困难. 通过回归系数分析表明, 不同的地表覆盖类型的辐射机制是不同的. 要精确地反演地表温度, 至少对地表分成三种覆盖类型, 即水覆盖的地表、雪覆盖的地表以及非雪和水覆盖的地表. 以MODIS地表温度产品作为评价标准, 物理统计方法的平均精度在2~3℃.     

基于AMSR-E的微波波段地表发射率反演——以青藏高原为例

青藏高原以其独特的特征在气候变化中起着重要的作用,而地表发射率对地表参数和大气参数的准确反演也非常重要,因此本文发展了青藏高原微波波段地表发射率的反演算法.首先通过辐射传输方程对地表发射率的反演算法进行了推导,并利用被动微波一维大气辐射模拟器的模拟数据对算法进行了验证,结果显示了较高的精度.接着结合微波辐射计AMSR-E的亮温数据和MODIS提供的大气廓线数据,利用本文发展的算法反演了青藏高原微波波段的地表发射率.最后,分析了青藏高原地表发射率的时空分布特征:从空间特征上分析,反演结果的空间分布符合青藏高原地表覆盖类型的变化,植被湖泊等可以在反演结果中很明显的显现;从时间特征上分析,在一个月的时间尺度上,发射率随时间变化并不明显,每天的变化值在0.01之内.另外通过对青藏高原裸露地表发射率的时间序列研究发现,地表发射率对降雨有非常敏感的响应.反演结果的合理性表明本文的算法具有可行性,可以利用该算法反演青藏高原的地表发射率并建立长时间序列的地表发射率数据库,为青藏高原其他地球系统参数的遥感反演提供基础,为青藏高原的相关地学研究提供数据支持.     

井下地电阻率观测中地表电流干扰影响计算

本文把地电阻率台站地下介质简化为水平三层均匀介质模型,以点电流模拟地表干扰电流,针对对称四极观测装置,计算了在不同电性结构中的不同深度观测时,地表电流干扰源对对称四极装置地电阻率观测的影响,计算得到:地表干扰源对电阻率观测的影响取决于电性结构的类型和层参数、供电电极和测量电极的埋深以及避开干扰源的距离.本文研究结果对实施井下电阻率观测中台址电性结构的选择、电极埋深、干扰源避让距离等有参考意义.     

中国地表气温变化对土地利用/覆被类型的敏感性

利用观测气温与再分析气温的差值分析了近40年中国地表气温变化对土地利用/覆被类型的敏感性.结果表明：土地利用/覆被类型对地表气温变化具有稳定的、系统性的影响,在全球变暖背景下各类型的响应不同,以沙地、戈壁和裸岩石砾地为主的未利用地升温幅度最大,为0.21℃/10a;其次是草地、耕地和城乡、工矿、居民用地,分别为0.12,0.10,0.12℃/10a;林地升温趋势最弱,为0.06℃/10a.总体来看,沙地、戈壁等未利用地和人类活动较多的区域地表升温幅度大,植被覆盖状况好的区域升温趋势则较弱;同一一级类型下理化特性及生物过程相似的二级类型对地表气温的影响程度相近,土地利用/覆被类型的变化需要达到一定的强度,导致地表特性发生本质改变后才会对局地气温产生较明显的影响;同一土地利用/覆被类型下,中国东部人类活动强度大的区域升温更为明显.这一结果为众多土地利用/覆被变化对气候影响的数值模拟试验研究提供了观测事实的支持.在区域尺度上预测未来中国气候变化不仅要考虑温室气体增加的影响,还要考虑土地利用/覆被类型及其变化的影响.     

沙漠陆面过程参数化与模拟

沙漠地区植被稀疏、干旱少雨,其陆面物理过程具有与全球其它地区显著不同的特点.本文利用巴丹吉林沙漠观测资料,分析和计算了地表反照率、比辐射率、粗糙度和土壤热容量、热传导系数等关键陆面过程参数,建立了适合于沙漠地区的陆面过程模式DLSM (Desert Land Surface Model),并与NOAH陆面过程模式的模拟结果和观测资料进行了比较.结果表明:巴丹吉林沙漠地表反照率为0.273,比辐射率为0.950,地表粗糙度为1.55×10^-3 m,土壤热容量和热扩散系数分别为1.08×10⁶ J·m^-3·K^-1和3.34×10^-7 m²·s.辐射传输、感热输送和土壤热传导过程是影响沙漠地区地表能量平衡的主要物理过程.通过对这三种过程的准确模拟检验,DLSM能够较准确地模拟巴丹吉林沙漠地气能量交换特征;短波辐射、长波辐射和感热通量的模拟结果与观测值间的标准差分别为7.98,6.14,33.9 W·m^-2,与NOAH陆面过程模式的7.98,7.72,46.6 W·m^-2的结果接近.地表反照率是沙漠地区最重要的陆面过程参数,地表反照率增大5%,向上短波辐射通量随之增加5%,感热通量则减小2.8%.本文研究结果对丰富陆面过程参数化方案,改进全球陆面过程模式、气候模式具有参考意义.     

用重力测量技术观测城市地表下沉的实验研究

本文用重力测量技术对城市地表下沉进行了实验研究,从2016年3月到2017年5月在武汉市内地表下沉较大的部分城区进行了7期流动重力观测实验,并用D-InSAR观测的垂向位移进行了验证.数值结果表明重力观测每期整网平差后点值平均精度都小于10×10~(-8)m·s~(-2),说明采用重力观测能在城市内获得高精度的区域重力变化.第7期相对于第1期的结果与D-InSAR在大致相同时间段内地表垂直位移结果比较表明,重力增加的大部分区域与D-InSAR观测到的地表下沉区域相一致,说明这些区域的重力增加主要是由地表下沉引起的.从第2到7期相对于第1期的重力变化说明在近12个月的时间内测区最大重力变化约40×10~(-8)m·s~(-2),且局部区域的重力值是逐渐增加的,说明地表下沉是持续进行的.本实验结果说明重力观测技术能为城市地表下沉提供重力观测约束和机制解释.     

长春地区地表温度日变、年变对地温测量的影响

通过实地观测试验，并采用傅里叶分析法进行理论分析，来研究长春地区地表温度日变、年变对地温测量的影响规律及影响深度，为在长春地区利用浅层地温测量方法研究地质问题提供重要参数信息.地温变化幅度随深度作指数衰减，衰减系数与地表温度周期、热扩散率有关.     

复杂地表条件下共反射面元（CRS）叠加方法研究

在地表地形复杂的情况下，静校正不易做好，这是制约山地资料处理质量的一个很重要的因素.复杂地表共反射面元（CRS）叠加不需对叠前数据做静校正，而且在得到叠加剖面后可以利用叠加得到的波场参数剖面实现基准面重建.地震数据的试算表明，复杂地表CRS叠加得出的剖面与常规处理剖面相比有着较高的信噪比和同相轴连续性.与水平地表CRS叠加不同的是，在复杂地表CRS叠加的时距公式中，波场三参数耦合，难以通过简化CRS道集的方法将它们全部分离并逐个优化.引入模拟退火算法后，有效地解决了这一组合优化的难题.     

Ondes de surface

Résumé Le but de ce mémoire est de démontrer quelques nouvelles propriétés générales d'une classe de fonctions (les ondes de surface) très importante par son rôle en physique et en géophysique.On commence par la démontration d'un théoréme fondamental qui établit l'identité de l'ensemble des ondes de surface et de l'ensemble des fonctions pour lesquelles, à tout instantt ₀ et en tout pointA ₀ de leur domaine d'existence, on peut écrire une proportionnalité entre intervalles de temps (situés, en général asymétriquement, de part et d'autre det ₀) et rayons des domaines circulaires centrés enA ₀, telle que les moyennes temporelles et spatiales correspondantes soient égales. Ce théorème permet d'écrire, en termes finis, la solution des équations aux dérivées partielles de toute onde de surface.On applique ensuite les résultats généraux: 1° à la variation diurne de la pression lce qui permet de voir que ce phénomène peut être considéré comme une onde de surface et donne la loi fondamentale en cos³ ( latitude) pour l'amplitude de l'onde semidiurne progressive]; 2° aux ondes de variation de la pression synoptique. Pour ces ondes de variation on établit les relations qui existent entre leurs paramètres caractéristiques et on détermine finalement leur configuration théorique.

---

Summary The aim of this paper is to give the proof of some new general properties of a class of functions (the surface waves) which is very important in physics and geophysics.We first give the proof of a fundamental theorem establishing the identity of the set of all surface waves and the set of functions for which, at any momentt ₀ and at any pointA ₀ of their domain, there exists a proportionality between time intervals comprisingt ₀ (asymmetrically, in the general case) and the radius of the circular domains centered onA ₀, such that the corresponding temporal and spatial means are equal. This theorem allows to write in finite terms the solution of the partial differential equations of any surface wave.The general results are then applied: 1° to the diurnal pressure variation, showing that this phenomenon can be considered as a surface wave and giving the fundamental law cos³ ( latitude) for the amplitude of the progressive or travelling 12-hourly wave; 2° to the waves of the synoptic pressure variations. For these waves the relations between their characteristic parameters is first established and finally their theoretical spatial configuration or pattern is deduced.

---

---

Communication faite le 23 Avril 1957 à la Cinquième Assemblée de la «Società Italiana di Geofisica e Meteorologia» (Genova, 23–25 Avril 1957).     

Analysis of surface chlorophyll a associated with sea surface temperature and surface wind in the South China Sea

Ocean Dynamics - In this study, the spatial and temporal variability in surface chlorophyll a (Chl-a) in the whole South China Sea (SCS) was investigated in detail by using 8-day, 4-km, gap-free...     

Directional statics in common reflection surface stack for rugged surface topography

Seismic data acquired along rugged topographic surfaces present well‐known problems in seismic imaging. In conventional seismic data processing, datum statics are approximated by the surface consistence assumption, which states that all seismic rays travel vertically in the top layer. Hence, the datum static for each single trace is constant. In case this assumption does not apply, non‐constant statics are required. The common reflection surface (CRS) stack for rugged surface topography provides the capability to deal with this non‐vertical static issue. It handles the surface elevation as a coordinate component and treats the elevation variation in the sense of directional datuming. In this paper I apply the CRS stack method to a synthetic data set that simulates the acquisition along an irregular surface topography. After the CRS stack, by means of the wavefield attributes, a simple algorithm for redatuming the CRS stack section to an arbitrarily chosen planar surface is performed. The redatumed section simulates a stack section whose acquisition surface is the chosen planar surface.     

Relationship between thermally forced surface wind and sea surface temperature gradient

An important part of the influence of the oceans on the atmosphere is through direct radiation, sensible heat flux and release of latent heat of evaporation, whereby all of these processes are directly related to the surface temperature of the oceans. A main effect of the atmosphere on the oceans is through momentum exchange at the air-ocean interface, and this process is directly related to the surface wind stress. The sea surface temperature (SST) and the surface wind stress are the two important components in the air-ocean system. If SST is given, a thermally forced boundary layer atmospheric circulation can be simulated. On the other hand, if the surface wind stress is given, the wind-driven ocean waves and ocean currents can be computed.The relationship between SST and surface wind is a coupling of the atmosphere and the oceans. It changes a one-way effect (ocean mechanically driven by atmosphere, or atmosphere thermally forced by oceans) into two-way air-sea interactions. Through this coupling the SST distribution, being an output from an ocean model, leads to the thermally forced surface winds, which feeds back into the ocean model as an additional forcing.Based on Kuo's planetary boundary layer model a linear algebraic equation is established to link the SST gradient with the thermally forced surface wind. The surface wind blows across the isotherms from cold to warm region with some deflection angle to the right (left) in the Northern (Southern) Hemisphere. Results from this study show that the atmospheric stratification reduces both the speed and the deflection angle of the thermally forced wind, however, the Coriolis' effect increases the wind speed in stable atmosphere (Ri>10^–4) and increases the deflection angle.     

Common reflection surface stack using dip decomposition for rugged surface topography

We present an extension of the Common Reflection Surface （CRS） stack that provides support for an arbitrary top surface topography. CRS stacking can be applied to the original prestack data without the need for any elevation statics. The CRS-stacked zero- offset section can be corrected （redatumed） to a given planar level by kinematic wave field attributes. The seismic processing results indicate that the CRS stacked section for rugged surface topography is better than the conventional stacked section for S/N ratio and better continuity of reflection events. Considering the multiple paths of zero-offset rays, the method deals with reflection information coming from different dips and performs the stack using the method of dip decomposition, which improves the kinematic and dynamic character of CRS stacked sections.     

From surface acidity to surface reactivity; inhibition of oxide dissolution

Paul Schindler's early work on the acid-base chemistry of oxides was instrumental for the development of the concept of surface complexation. This approach has not only been important in establishing a theory on the adsorption of metal ions and ligands as a function of pH and solution variables, but has become essential in establishing surface speciation (coordinative structural and electronic arrangement at the solidwater interface) which in turn determines surface reactivity. The factors that affect dissolution of Fe(III) (hydr)oxides and inhibition of dissolution are discussed. A few examples for the inhibition of reductive and ligand-promoted dissolution by binuclear complexes of oxoanions (phosphate, borate) and of protonpromoted dissolution by Cr(III) are given.     

Determination of bare surface soil moisture from combined temporal evolution of land surface temperature and net surface shortwave radiation

Land surface soil moisture (SSM) is an important variable for hydrological, ecological, and meteorological applications. A multi‐linear model has recently been proposed to determine the SSM content from the combined diurnal evolution of both land surface temperature (LST) and net surface shortwave radiation (NSSR) with the parameters TN (the LST mid‐morning rising rate divided by the NSSR rising rate during the same period) and t_d (the time of daily maximum temperature). However, in addition to the problem that all the coefficients of the multi‐linear model depend on the atmospheric conditions, the model also suffers from the problems of the nonlinearity of TN as a function of the SSM content and the uncertainty of determining the t_d from the diurnal evolution of the LST. To address these problems, a modified multi‐linear model was developed using the logarithm of TN and normalizing t_d by the mid‐morning temperature difference instead of using the TN and t_d. Except for the constant term, the coefficients of all other variables in the modified multi‐linear model proved to be independent of the atmospheric conditions. Using the relevant simulation data, results from the modified multi‐linear model show that the SSM content can be determined with a root mean square error (RMSE) of 0.030m³/m³, provided that the constant term is known or estimated day to day. The validation of the model was conducted using the field measurements at the Langfang site in 2008 in China. A higher correlation is achieved (coefficient of determination: R² = 0.624, RMSE = 0.107m³/m³) between the measured SSM content and the SSM content estimated using the modified multi‐linear model with the coefficients determined from the simulation data. Another experiment is also conducted to estimate the SSM content using the modified model with the constant term calibrated each day by one‐spot measurements at the site. The estimation result has a relatively larger error (RMSE = 0.125m³/m³). Additionally, the uncertainty of the determination of the coefficients is analysed using the field measurements, and the results indicate that the SSM content obtained using the modified model accurately characterizes the surface soil moisture condition. Copyright © 2012 John Wiley & Sons, Ltd.     

Effect of surface stress on magneto-elastic surface waves in finitely conducting media

This paper deals with the investigation of the effect of surface stress and conductivity on the propagation of surface wave in isotropic, homogeneous, elastic media under the action of a primary magnetic field. Formulation of the general surface wave propagation problem has been made, and the corresponding frequency equation has been derived. Frequency equations for Rayleigh wave, surface shear wave and Stoneley wave have been deduced from that of general surface wave as special cases. The effects of surface stress and magnetic field on the wave velocities and attenuation factors of Rayleigh wave and surface shear wave are shown by numerical calculations and graphs. Some important wave velocity equations, as obtained by other authors, have been deduced as special cases from the wave velocity equation for Stoneley wave. It is found that the combined effect of surface stress and magnetic field modulates the wave velocity ratios and attenuation factors of Rayleigh wave and surface shear wave to a considerable extent.