Insight into adsorption equilibrium,kinetics and thermodynamics of lead onto alluvial soil

In the present study, adsorption of lead (II) ions from aqueous solution by alluvial soil of Bhagirathi River was investigated under batch mode. The influence of solution pH, sorbent dose, initial lead (II) concentration, contact time, stirring rate and temperature on the removal process were investigated. The lead adsorption was favored with maximum adsorption at pH 6.0. Sorption equilibrium time was observed in 60 min. The equilibrium adsorption data were analyzed by the Freundlich, Langmuir, Dubinin–Radushkevich and Temkin adsorption isotherm models. The kinetics of lead (II) ion was discussed by pseudo first-order, pseudo second-order, intra-particle diffusion, and surface mass transfer models. It was shown that the adsorption of lead ions could be described by the pseudo second-order kinetic model. The activation energy of the adsorption process (E _a) was found to be ?38.33 kJ mol^?1 using the Arrhenius equation, indicating exothermic nature of lead adsorption onto alluvial soil. Thermodynamic parameters, such as Gibbs free energy (?G ⁰), the enthalpy (?H ⁰), and the entropy change of sorption (?S ⁰) have also been evaluated and it has been found that the adsorption process was spontaneous, feasible, and exothermic in nature. The results indicated that alluvial soil of Bhagirathi River can be used as an effective and low cost adsorbent to remove lead ions from aqueous solutions.     

Removal of cadmium (II) from aqueous solution and natural water samples using polyurethane foam/organobentonite/iron oxide nanocomposite adsorbent

A novel polyurethane foam/organobentonite/iron oxide nanocomposite adsorbent was successfully prepared via in situ polymerization of toluene diisocyanate and polyol in presence of 5 wt% organobentonite/iron oxide. The obtained nanocomposite was characterized in detail, and the results revealed that the clay layers are exfoliated and/or intercalated in the polymer matrix forming a nanocomposite structure. The application of the prepared nanocomposite for adsorption of cadmium ions from aqueous solution was tested as a function of various experimental parameters using batch procedures. Adsorptive removal of Cd(II) onto the nanocomposite attained maximum at adsorbent content 1.5 g/L, pH 6, and the equilibrium was established within 60 min. Kinetic studies showed that the experimental data fit very well to pseudo-second-order model, and the adsorption process proceeds through three steps. It was found that external liquid film and intraparticle diffusion steps deeply affect the rate of Cd²⁺ ions adsorption onto the synthesized nanocomposite. Langmuir isotherm model fitted the adsorption data better than Freundlich with a maximum adsorption capacity (q _m) for Cd(II) equal to 78 mg/g under the specified experimental conditions. The synthesized nanocomposite afforded effective extraction for Cd²⁺ ions from natural water samples and excellent reusability feature. This study declares the potential efficiency of a new clay/polymer nanocomposite as alternative for wastewater remediation.     

Adsorption of copper, nickel and lead ions from synthetic semiconductor industrial wastewater by palm shell activated carbon

Granular activated carbon produced from palm kernel shell was used as adsorbent to remove copper, nickel and lead ions from a synthesized industrial wastewater.Laboratory experimental investigation was carried out to identify the effect of pH and contact time on adsorption of lead, copper and nickel from the mixed metals solution. Equilibrium adsorption experiments at ambient room temperature were carried out and fitted to Langmuir and Freundlich models. Results showed that pH 5 was the most suitable, while the maximum adsorbent capacity was at a dosage of 1 g/L, recording a sorption capacity of 1.337 mg/g for lead, 1.581 mg/g for copper and 0.130 mg/g for nickel. The percentage metal removal approached equilibrium within 30 min for lead, 75 min for copper and nickel, with lead recording 100 %, copper 97 % and nickel 55 % removal, having a trend of Pb²⁺ > Cu²⁺ > Ni²⁺. Langmuir model had higher R² values of 0.977, 0.817 and 0.978 for copper, nickel and lead respectively, which fitted the equilibrium adsorption process more than Freundlich model for the three metals.     

Preparation and characterization of biosorbents and copper sequestration from simulated wastewater

This paper reports the potential of chemically treated wood chips to remove copper (II) ions from aqueous solution a function of pH, adsorbent dose, initial copper (II) concentration and contact time by batch technique. The wood chips were treated with (a) boiling, (b) formaldehyde and (c) concentrated sulphuric acid and characterized by Fourier transform infrared spectroscopy, scanning electron microscopy and energy dispersive analysis X-ray. pH 5.0 was optimum with 86.1, 88.5 and 93.9 % copper (II) removal by boiled, formaldehyde-treated and concentrated sulphuric acid-treated wood chips, respectively, for dilute solutions at 20 g L^?1 adsorbent dose. The experimental data were analysed using Freundlich, Langmuir, Dubinin–Radushkevich and Temkin isotherm models. It was found that Freundlich and Langmuir models fitted better the equilibrium adsorption data and the adsorption process followed pseudo-second-order reaction kinetics. The results showed that the copper (II) is considerably adsorbed on wood chips and it could be an economical option for the removal of copper from aqueous systems.     

Kinetic and equilibrium study of Ni(II) sorption from aqueous solutions onto Peganum harmala-L

In this study, the adsorption behavior of Ni(II) in an aqueous solution system using natural adsorbent Peganum harmala-L was measured via batch mode. The prepared sorbent was characterized by scanning electron microscope, Fourier transform infrared spectroscopy, N₂ adsorption–desorption and pH_zpc. Adsorption experiments were carried out by varying several conditions such as contact time, metal ion concentration and pH to assess kinetic and equilibrium parameters. The equilibrium data were analyzed based on the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherms. Kinetic data were analyzed using the pseudo-first-order, pseudo-second-order and intra-particular diffusion models. Experimental data showed that at contact time 60 min, metal ion concentration 50 mg/L and pH 6, a maximum amount of Ni(II) ions can be removed. The experimental data were best described by the Langmuir isotherm model as is evident from the high R ² value of 0.988. The adsorption capacity (q _m) obtained was 68.02 mg/g at an initial pH of 6 and a temperature of 25 °C. Kinetic studies of the adsorption showed that equilibrium was reached within 60 min of contact and the adsorption process followed the pseudo-first-order model. The obtained results show that P. harmala-L can be used as an effective and a natural low-cost adsorbent for the removal of Ni(II) from aqueous solutions.     

Adsorption kinetics and thermodynamics of organophosphorus profenofos pesticide onto Fe/Ni bimetallic nanoparticles

Bimetallic Fe/Ni nanoparticles were synthesized and used for the removal of profenofos organophosphorus pesticide from aqueous solution. These novel bimetallic nanoparticles (Fe/Ni) were characterized by scanning electron microscopy, energy-dispersive X-ray analysis spectroscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The effect of the parameters of initial pesticide concentration, pH of the solution, adsorbent dosage, temperature, and contact time on adsorption was investigated. The adsorbent exhibited high efficiency for profenofos adsorption, and equilibrium was achieved in 8 min. The Langmuir, Freundlich, and Temkin isotherm models were used to determine equilibrium. The Langmuir model showed the best fit with the experimental data (R ² = 0.9988). Pseudo-first-order, pseudo-second-order, and intra-particle diffusion models were tested to determine absorption kinetics. The pseudo-second-order model provided the best correlation with the results (R ² = 0.99936). The changes in the thermodynamic parameters of Gibb’s free energy, enthalpy, and entropy of the adsorption process were also evaluated. Thermodynamic parameters indicate that profenofos adsorption using Fe/Ni nanoparticles is a spontaneous and endothermic process. The value of the activation energy (E _a = 109.57 kJ/mol) confirms the nature of the chemisorption of profenofos onto Fe/Ni adsorbent.     

Application of dried plant biomass as novel low-cost adsorbent for removal of cadmium from aqueous solution

Heavy metals are a threat to human health and ecosystem. These days, great deal of attention is being given to green technologies for purification of water contaminated with heavy metal ions. Biosorption is one among such emerging technologies, which utilizes naturally occurring waste materials to sequester heavy metals from wastewater. Cadmium has hazardous impact on living beings; therefore, its removal through green and economical process is an important task. The aim of the present study was to utilize the locally available Portulaca oleracea plant biomass as an adsorbent for cadmium removal from aqueous solution. The biomass was obtained after drying and grinding the portulaca leaves and stem. No chemical treatment was done on the adsorbent so that it remained green in a true sense. Batch experiments were performed at room temperature. The critical parameters studied were effects of pH, contact time, initial metal ion concentration and adsorbent dose on the adsorption of cadmium. The maximum adsorption was found to be 72 %. The kinetic data were found to best fit the pseudo-second-order equation. High adsorption rates were obtained in the initial 45 min, and adsorption equilibrium was then gradually achieved in about 100 min. Adsorption increased with increase in pH for a range 2 and 6. The equilibrium adsorption results closely followed both the Langmuir and Freundlich isotherms. The values of constants were calculated from isotherms. Results indicated that portulaca plant biomass could be developed as a potential material to be used in green water treatment devices for removal of metal ions.     

Single and binary adsorption of lead and cadmium ions from aqueous solution using the clay mineral beidellite

Beidellite, a low-cost, locally available and natural mineral was used as an adsorbent for the removal of lead and cadmium ions from aqueous solutions in batch experiments. The kinetics of adsorption process was tested for the pseudo first-order, pseudo second-order reaction and intra-particle diffusion models. The rate constants of adsorption for all these kinetic models were calculated. Comparison amongst the models showed that the sorption kinetics was best described by the pseudo second-order model. Langmuir and Freundlich isotherm models were applied to the experimental equilibrium data for different temperatures. The adsorption capacities (Q°) of beidellite for lead and cadmium ions were calculated from the Langmuir isotherm. It was found that adsorption capacity was in the range of 83.3–86.9 for lead and 42–45.6 mg/g for cadmium at different temperatures. Thermodynamic studies showed that the metal uptake reaction by beidellite was endothermic in nature. Binary metal adsorption studies were also conducted to investigate the interactions and competitive effects in binary adsorption process. Based on the optimum parameters found, beidellite can be used as adsorbent for metal removal processes.     

Nettle ash as a low cost adsorbent for the removal of nickel and cadmium from wastewater

This study was focused on nettle ash as an alternative adsorbent for the removal of nickel (II) and cadmium (II) from wastewater. Batch experiments were conducted to determine the factors affecting adsorption of nickel (II) and cadmium (II). The adsorption process is affected by various parameters such as contact time, solution pH and adsorbent dose. The optimum pH required for maximum adsorption was found to be 6. The experimental data were tested using Langmuir, Freundlich and Tempkin equations. The data were fitted well to the Langmuir isotherm with monolayer adsorption capacity of 192.3 and 142.8 mg/g for nickel and cadmium, respectively. The adsorption kinetics were best described by the pseudo second order model. The cost of removal is expected to be quite low, as the adsorbent is cheap and easily available in large quantities. The present study showed that nettle ash was capable of removing nickel and cadmium ions from aqueous solution.     

Adsorption of copper and zinc by oil shale

 Oil shale is able to remove appreciable amounts of copper and zinc ions from aqueous solutions. It was noted that an increase in the adsorbent concentration with constant copper or zinc concentration resulted in greater metal removal from solution. An increase in the copper or zinc concentration with a constant sorbent concentration resulted in higher metal loading per unit weight of sorbent. For both metals, copper and zinc, equilibrium was attained after 24-h contact time. Increase in the initial pH or temperature of the metal solution resulted in an increase in the metal uptake per unit weight of the sorbent. Freundlich isotherm model was found to be applicable for the experimental data of Cu²⁺ and Zn²⁺. The results showed that oil shale could be used for the adsorption of the Cu²⁺ and Zn²⁺ with higher affinity toward Zn²⁺ ions. Addition of sodium salt to the metal solution influenced copper removal positively, but inhibited zinc removal. Received: 3 January 2000 · Accepted: 27 June 2000     

Ultrafast removal of heavy metals by tin oxide nanowires as new adsorbents in solid-phase extraction technique

In the present research, the removal of lead(II) and copper(II) from aqueous solutions is studied, using SnO₂ nanowires as new adsorbent on solid-phase extraction disk and compared with pine core and buttonwood as biosorbents. Batch adsorption experiments were performed as a function of pH, adsorption time, solute concentration and adsorbent dose for biosorbents. Also, the pH, transfer rate of solution and metal concentration were selected as experimental parameters for the removal of heavy metals by SnO₂ nanowires. All of the parameters were optimized by experimental design method for sorbents. The experimental equilibrium adsorption data are tested for the Langmuir and Freundlich equations. Results indicate the following order to fit the isotherms: Langmuir > Freundlich, in case of lead and copper ions. The removal of Cu(II) and Pb(II) was performed by selected sorbents in the presence of interferences ions. This led to no remarkable decrease in the removal efficiency of SnO₂ nanowires. Using the SnO₂ nanowires in the wastewater treatment indicated 96.8 and 85.28% removal efficiency in only 7 min for Pb(II) and Cu(II), respectively. SnO₂ nanowires were found as reusable sorbent. Therefore, SnO₂ nanowires have a good potential for application in environmental protection.     

Hydrothermal synthesis of hydroxy sodalite from fly ash for the removal of lead ions from water

Zeolites are known to possess valuable physiochemical properties such as adsorption, cation exchange, molecular sieving, and catalysis. In addition, zeolites are highly selective scavengers of a variety of heavy metals from liquid effluents through the process of ion exchange. The present study was performed to hydrothermally synthesize Na₈[AlSiO₄]₆(OH)₂·2H₂O (also known as hydroxy sodalite hydrate). Due to its small aperture size, this material can be an ideal candidate for the separation of small molecules and ions from aquatic and gas mixtures. Synthetic zeolites offer many advantages over natural zeolites, such as higher ion affinity and adsorption capacity. Batch adsorption isotherm studies were conducted to evaluate the obtained adsorbent for the lead ion removal from aqueous media. Modeling lead ion adsorption using Langmuir and Freundlich isotherm expressions determined the capacity of the adsorbent. A removal efficiency of 98.1 % in a 3.0 g/l adsorbent/solution mixture with a maximum adsorption capacity of 153.8 mg/g was obtained. One potential application of the synthesized zeolite is for the lead removal in point-of-use treatment devices.     

Heavy metals removal from synthetic wastewater by a novel nano-size composite adsorbent

The effects of varying operating conditions on metals removal from aqueous solution using a novel nano-size composite adsorbent are reported in this paper. Characterization of the composite adsorbent material showed successful production of carbon nanotubes on granular activated carbon using 1 % nickel as catalyst. In the laboratory adsorption experiment, initial mixed metals concentration of 2.0 mg/L Cu²⁺, 1.5 mg/L Pb²⁺ and 0.8 mg/L Ni²⁺ were synthesized based on metals concentration from samples collected from a semiconductor industry effluent. The effects of operation conditions on metals removal using composite adsorbent were investigated. Experimental conditions resulting in optimal metals adsorption were observed at pH 5, 1 g/L dosage and 60 min contact time. It was noted that the percentage of metals removal at the equilibrium condition varied for each metal, with lead recording 99 %, copper 61 % and nickel 20 %, giving metal affinity trend of Pb²⁺ > Cu²⁺ > Ni²⁺ on the adsorbent. Langmuir’s adsorption isotherm model gave a higher R² value of 0.93, 0.89 and 0.986 for copper, nickel and lead, respectively, over that of Freundlich model during the adsorption process of the three metals in matrix solution.     

Adsorption of lead using a new green material obtained from Portulaca plant

In the present study the potential of a new green material obtained from Portulaca oleracea plant was investigated. The material was used without any chemical treatment to study the adsorption behavior of lead ions from aqueous solution. Various batch experiments were carried out using different experimental conditions such as pH, contact time, adsorbent concentration, and metal ion concentration to identify the optimum conditions. The influence of these parameters on the adsorption capacity was studied. Results showed the optimum initial pH for adsorption as 6. Adsorption equilibrium was reached in 120?min. The adsorption data were modeled using both the Langmuir and Freundlich classical adsorption isotherms. Results show ~78% removal of lead from aqueous solution. The kinetic data corresponded well with pseudo second-order equation. From the initial results, the green material obtained from the waste of Portulaca seems to be a potential low-cost adsorbent for removal of lead ions from water.     

Raw and calcination-modified coal waste as adsorbents to remove cadmium from simulated mining wastewater

The adsorption of cadmium from simulated mining wastewater by coal waste (CW) and calcination-modified coal waste (MCW) was investigated. Effects of pH, initial concentration, particle size of adsorbent, adsorbent dosage and temperature were studied in batch experiments. The adsorption efficiency for cadmium increased with increasing pH, and the optimum pH for cadmium adsorption onto MCW and CW was 6.0 and 6.5, respectively. Kinetic experiments showed that the adsorption equilibrium was reached within 120 min and followed pseudo-second-order model well. The adsorption isotherm data fit Langmuir and Freundlich models, and the adsorption capacity of cadmium on the two adsorbents increased with increasing temperature from 298 to 318 K. MCW had a higher adsorption capacity of cadmium than CW, because calcination treatment can make CW to have more loose structure and higher specific surface area. Thermodynamic parameters, the Gibbs free energy change (?G⁰), enthalpy change (?H⁰) and entropy change (?S⁰), were calculated and the results showed that the adsorption of cadmium on CW and MCW was spontaneous and endothermic. Fourier transform infrared studies indicated silanol and aluminol groups were responsible for cadmium binding. The desorption results indicated that the two adsorbents could be used repeatedly at least three times without significant decrease in the adsorption capacity for cadmium. The results suggested that modified CW could have high potential as low-cost adsorbent for cadmium removal.     

Removal of lead(II) from aqueous stream by hydrophilic modified kapok fiber using the Fenton reaction

A hydrophilic kapok fiber was prepared by a chemical process of the Fenton reaction and used as an adsorbent to remove Pb(II) from aqueous solution. The effects of experimental parameters including pH, contact time, Pb(II) concentration, and coexisting heavy metals were estimated as well as evaluated. The optimum concentrations of FeSO₄ and H₂O₂ for the Fenton reaction-modified kapok fiber (FRKF) were 0.5 mol L^?1 and 1 mol L^?1, respectively. The adsorption kinetic models and isotherm equations of Langmuir and Freundlich were conducted to identify the most optimum adsorption rate and adsorption capacity of Pb(II) on FRKF. The FRKF displayed an excellent adsorption rate for Pb(II) in single metal solution with the maximum adsorption capacity of 94.41?±?7.56 mg g^?1 at pH 6.0. Moreover, the FRKE still maintained its adsorption advantage of Pb(II) in the mixed metal solution. The FRKF exhibited a considerable potential in removal of metal content in wastewater streams.     

Adsorption efficiency,thermodynamics and kinetics of Schiff base-modified nanoparticles for removal of heavy metals

Nanosilica particles modified by Schiff base ligands 3-methoxy salicylaldimine propyl triethoxysilane (MNS₁), 5-bromo salicylaldimine propyl triethoxysilane (MNS₂) and 3-hydroxy salicylaldimine propyl triethoxysilane (MNS₃) were prepared, and their potential for separation of copper, lead, zinc, cadmium, cobalt and nickel ions from aqueous solutions was examined. The effect of parameters influencing adsorption efficiency including aqueous-phase pH, amount of adsorbent, stirring time and initial concentration of the metal ions was assessed and discussed. Although MNS₁ and MNS₃ removed lead ions efficiently, all adsorbents showed strong selectivity toward copper ions. It was shown that, under some circumstances, MNS₃ decreased the amount of other ions, particularly cobalt, in the aqueous phase. The adsorbents were also applied for removal of copper and lead ions from real samples. Possible quantitative desorption of the metal ions loaded onto the adsorbents suggests their multiple uses in adsorption–desorption process. Investigation of temperature dependency of the process led to determination of the ΔH°, ΔS° and ΔG° values. This investigation indicates that the adsorption of copper ions onto the all studied adsorbents and lead ions onto MNS₁ and MNS₃ is endothermic. The Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherms were tested to describe the equilibrium data. Pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion equations were applied to study the kinetics of copper and lead adsorption onto the modified nanoparticles. This investigation indicates that the process for all adsorbents follows pseudo-second-order kinetics and suggests a chemisorption mechanism for the adsorption processes by the studied adsorbents.     

Ionic solid-impregnated sulphate-crosslinked chitosan for effective adsorption of hexavalent chromium from effluents

Microwave-assisted tetrabutyl ammonium-impregnated sulphate-crosslinked chitosan was synthesized for enhanced adsorption of hexavalent chromium. The adsorbent obtained was extensively characterized using Fourier transform infrared, X-ray diffraction, scanning electron microscopy and energy-dispersive X-ray studies. Various isotherm models such as Langmuir, Freundlich and Dubinin–Radushkevich were studied to comprehend the adsorption mechanism of hexavalent chromium by the adsorbent. Maximum adsorption capacity of 225.9 mg g^?1 was observed at pH 3.0 in accordance with Langmuir isotherm model. The sorption kinetics and thermodynamic studies revealed that adsorption of hexavalent chromium followed pseudo-second-order kinetics with exothermic and spontaneous behaviour. A column packed with 1 g of adsorbent was found to give complete adsorption of Cr(VI) up to 900 mL of 200 mg L^?1 solution which discerns the applicability of the adsorbent material for higher sample volumes in column studies. The effective adsorption results were obtained due to both ion exchange and ion pair interaction of adsorbent with hexavalent chromium. Greener aspect of overall adsorption was regeneration of the adsorbent which was carried out using sodium hydroxide solution. In the present study, the regenerated adsorbent was effectively reused up to ten adsorption–desorption cycles with no loss in adsorption efficiency.     

Assessment of raw clays from Maghnia (Algeria) for their use in the removal of Pb<Superscript>2+</Superscript> and Zn<Superscript>2+</Superscript> ions from industrial liquid wastes: a case study of wastewater treatment

Homogenized samples of raw clays resulting from two (2) different lots of natural clays from Maghnia (Algeria) have been assessed for their potential use in the removal of Pb²⁺ and Zn²⁺ ions from industrial liquid wastes (LW). Raw and acid-activated samples have been characterized by powder X-ray diffraction, FT-IR spectroscopy, electron microscopy (SEM), and X-ray fluorescence (XRF) and used as adsorbents for the removal of Pb²⁺ and Zn²⁺ ions from aqueous system using adsorption method under different conditions. The effect of factors including contact time, pH, and dosage on the adsorption properties of Pb²⁺ and Zn²⁺ ions onto clays was investigated at 25 °C. The obtained results revealed that the removal percentages of Pb²⁺ and Zn²⁺ ions, from both aqueous solution (AS) and LW, were varying between 90 and 98% for 40 min and optimal pH values ranged from 5 to 6 for Pb²⁺ and Zn²⁺ ions, respectively. The kinetics of both Pb²⁺ and Zn²⁺ ion adsorption fitted well with the pseudo-second-order model. Langmuir, Freundlich, and Temkin adsorption isotherms were used, and their constants were evaluated. The values of thermodynamic parameters, ΔH°, ΔS°, and ΔG° indicated that the adsorption of Pb²⁺ and Zn²⁺ ions was spontaneous and exothermic process in nature. The adsorption and desorption isotherms indicated that Pb²⁺ and Zn²⁺ adsorption to raw clays was reversible. The experimental results obtained showed that the raw clays from Maghnia (Algeria) had a great potential for removing Pb²⁺ and Zn²⁺ ions from industrial liquid wastes using adsorption method.     

Geochemical evaluation and environmental application of Yemeni natural zeolite as sorbent for Cd<Superscript>2+</Superscript> from solution: kinetic modeling,equilibrium studies,and statistical optimization

Yemeni natural zeolite was characterized by XRD, SEM, FTIR and XRF as well as its applicability as a sorbent material for Cd²⁺ ions in aqueous solutions. The zeolitic sample is clinoptilolite-K of heulandite group with intermediate Si/Al ratio. The removal% of Cd²⁺ by natural clinoptilolite was investigated as a function of contact time, zeolite dose, pH and initial concentration of Cd²⁺ ions. Kinetic experiments indicated that sorption of Cd²⁺ follows two steps: rapid ion exchange process on the outer surface is followed by slow adsorption process on the inner surface of clinoptilolite. The equilibrium was attained after 120 min, and the results were fitted well with pseudo-second order and Elovich kinetic models. The Cd²⁺ removal% is strongly dependent on pH value and increases with the increasing pH value. Equilibrium sorption isotherm of Cd²⁺ by clinoptilolite was described well using the Langmuir, Freundlich, and Temkin isotherms models. However, the data relatively well fitted with Freundlich model (R ² = 0.97) rather than by the other models. Response surface methodology in conjunction with central composite rotatable statistical design was used to optimize the sorption process. The model F-value indicated the high significance of second-order polynomial model to represent the interaction between the operating parameters. From the Design Expert’s optimization function, the predicted optimum conditions for maximum removal% of Cd²⁺ (80.77%) are 116 min contact time, 0.27 gm dose, and pH 7 at an initial Cd²⁺ concentration of 25 mg/L.