Compressional behavior of clayey sand and transition fines content

Clayey sand can be considered as a composite matrix of coarse and fine grains. The interaction between coarser and finer grain matrices affects the overall stress–strain behavior of these soils. Intergranular void ratio, e_s (which is the void ratio of the coarser grain matrix) can be utilized as an alternative parameter to express the compressive response of such soils. Oedometer tests conducted on reconstituted kaolinite–sand mixtures indicate that initial conditions, percentage of fines, and stress conditions influence the compression characteristics evidently. Tests showed that, up to a fraction of fines, which is named as transition fines content (FC_t), compression behavior of the mixtures is mainly controlled by the sand grains. When concentration of fines exceeds FC_t, kaolinite controls the compression. It was found that FC_t varies between 19% and 34% depending on the above mentioned factors. This range of fines content is also consistent with various values reported in literature regarding the strength alteration. Performed direct shear tests revealed that there is also a close relationship between transition fines content and shear strength, which is harmonic with the oedometer test results.     

Shear strength and pore-water pressure characteristics of sandy soil mixed with plastic fine

Recent earthquake case histories have revealed the liquefaction of mixtures of sand and fine particles during earthquakes. Different from earlier studies which placed an emphasis on characterisation of liquefaction in terms of the induced shear stress required to cause liquefaction, this study adopted a strain approach because excess pore-water pressure generation is controlled mainly by the level of induced shear strains. The current study includes the results of a set of laboratory tests carried out on sand specimens with the same relative densities and variation in the plastic fines (kaolinite or bentonite) contents ranging from 0 to either 30 % and consolidated at mean confining pressure of 100, 200 and 300 kPa using static triaxial test apparatus, in order to study the influence of fine content and other parameters on the undrained shear strength and liquefaction potential of clayey sand specimens; also, pore-water pressures in the specimens are discussed. Results of tests show that the peak strength decreases as the fines (kaolinite or bentonite) content increases up to a threshold content of fines (FC_th) after which, increases in plastic fine content lead to improve the peak shear strength of specimens, and also the ultimate steady-state strength has been improved due to the increased in plastic fines content. Also, pore pressure build-up in clayey sands is generally slower than that observed in pure sand.     

Compression and consolidation anisotropy of some soft soils

The compression and consolidation anisotropy of 11 soft soils were studied by conducting oedometer tests on sets of duplicate undisturbed specimens prepared in the vertical and horizontal directions from adjacent sections of carefully sampled borehole cores. The one-dimensional compression, yield and creep characteristics of the various silts, clays and amorphous peaty material tested were similar for the vertical and horizontal directions. The exception was the structured, coarse fibrous peaty material which was strongly cross-anisotropic. Drainage occurred more rapidly in the horizontal direction with horizontal-to-vertical permeability ratios r _k of 1.0–1.7. Higher r _k values were associated with more marked fabrics, namely for clays with fine sand partings, fibrous organic inclusions or fine root-holes and the laminated silts. The r _k value was for practical purposes independent of the stress level. Brendan C. O’Kelly: Formerly Scott Wilson Consulting Engineers, UK     

钙质粗粒料颗粒强度和压缩特性的试验研究

目前对钙质土压缩特性的研究主要集中在钙质细砂,而实际工程中广泛存在钙质粗粒料,因此对钙质粗粒料压缩特性开展研究具有重要意义。通过颗粒强度测定仪和全自动大型固结仪对钙质土进行了单颗粒破碎试验和一维压缩试验,研究了颗粒粒径和相对密度对钙质粗粒料的颗粒强度和压缩特性的影响。单颗粒试验结果表明,钙质砂单颗粒的特征应力随着颗粒相对密度的增大而增大;单颗粒的破碎强度具有明显的尺寸效应,可利用单颗粒的特征应力进行标准化,且服从Weibull分布。压缩试验结果表明,单一粒径试样破碎后的分形维数随颗粒粒径的增大而增大;试样的Hardin破碎率与塑性功的关系为幂函数关系;在本次试验条件下,单一粒径试样的屈服应力与单颗粒的特征应力存在近似线性关系。     

Geotechnical reconnaissance and liquefaction analyses of a liquefaction site with silty fine sand in Southern Taiwan

Geotechnical reconnaissance of a recurrent liquefaction site at a Quaternary alluvial deposit in southern Taiwan was conducted to establish a comprehensive case history for liquefaction on silty fine sand with high fines content. The liquefaction occurred at a silty fine sand layer with D₅₀ = 0.09 mm and fines content greater than 35% and was triggered by a M_w = 6.4 earthquake on March 4, 2010, which induced maximum horizontal acceleration up to 0.189 g at the site. In situ subsurface characterizations, including standard penetration test, cone penetration test, and shear wave velocity measurement, were performed as well as cyclic simple shear tests on undisturbed specimens retrieved by a modified hydraulic piston sampler. Comparisons of cyclic resistance ratios (CRRs) indicate that CPT sounding with standard penetration rate could overestimate the resistance ratio and drainage conditions during penetration should be considered for high fines content soil in the liquefaction analysis. Additionally, variations of CRRs from different in situ tests indicate that correlations among in situ tests and CRR could be soil specific and precautions should be taken when using these curves on silty fine sands.     

基于粒间状态变量的含细粒砂土力学性状分析

在探讨含细粒砂土内部结构和粒间相互作用的基础上,引入粒间状态变量概念,对含细粒砂土力学性状随细粒含量的变化进行了预测分析:当D_rs >>0时含细粒砂土类似于e=e_c时均质砂的不排水性状,具有较高的强度;当D_rs→0时含细粒砂土最终性状具有不确定性;当D_rs < 0时含细粒砂土表现为剪缩性状。将南京砂中粗粒和细粒进行重新配制获得含不同细粒的砂土,对它们进行不排水剪试验;在利用粒间状态变量对试验结果进行分析的基础上,将试验结果与预测分析进行比对,两者的吻合性较高。在e_c-logS_us空间内稳态线随粉粒的增加而向上移动,且各稳态线间呈平行状。因此,粒间状态变量能较好地反映无黏性土力链的变化,是描述砂土微观结构的新途径。     

含细粒砂土反常剪切行为的数值模拟研究

针对含细颗粒砂土的反常剪切行为,开展了双轴剪切试验的数值模拟,从宏细观角度分析了其反常剪切行为发生的内在机制。数值模拟结果表明,增加围压能提高含细颗粒砂土的抗剪切液化能力,该反常行为的根本原因在于围压上升使得粗细颗粒更有效地参与了力链传递,增加了颗粒间的接触,增强了土体的密实度。细颗粒在土骨架中的移动对砂土的液化起着至关重要的作用,而粗颗粒仅起次要作用。研究表明,细颗粒在剪切过程中会持续从有效土骨架中移出成为无效颗粒,而部分粗颗粒也因失去细颗粒的支撑作用会脱离土骨架,直至试样最终液化。细颗粒一般参与土骨架中的弱力链,而粗颗粒则一般参与强力链,导致细颗粒较粗颗粒更容易在土骨架中移动。     

Effect of fines content and void ratio on the saturated hydraulic conductivity and undrained shear strength of sand–silt mixtures

The hydraulic conductivity represents an important indicator parameter in the generation and redistribution of excess pore pressure of sand–silt mixture soil deposits during earthquakes. This paper aims to determine the relationship between the undrained shear strength (liquefaction resistance) and the saturated hydraulic conductivity of the sand–silt mixtures and how much they are affected by the percentage of low plastic fines (finer than 0.074 mm) and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests carried out on samples reconstituted from Chlef river sand with 0, 10, 20, 30, 40, and 50 % non-plastic silt at an effective confining pressure of 100 kPa and two initial relative densities (D _r = 20, 91 %) are presented and discussed. It was found that the undrained shear strength (liquefaction resistance) can be correlated to the fines content, intergranular void ratio and saturated hydraulic conductivity. The results obtained from this study reveal that the saturated hydraulic conductivity (k _sat) of the sand mixed with 50 % low plastic fines can be, in average, four orders of magnitude smaller than that of the clean sand. The results show also that the global void ratio could not be used as a pertinent parameter to explain the undrained shear strength and saturated hydraulic conductivity response of the sand–silt mixtures.     

How fines content affects granular plasticity of under-filled binary mixtures

In recent years, binary mixtures have been the subject of numerous experimental and numerical studies. However, few attempts have been made on investigating the effect of fines content (fc) on the non-associated plasticity of binary mixtures, which is significant for constitutive modelling of such material. Thanks to 2D DEM simulations, this study aims to provide an understanding of how fc affects the non-associated character of the flow rule and the resulting material instability in binary mixtures. For under-filled materials (where coarse grains constitute most of the load-bearing skeleton), fine grains help to stabilize the granular assembly (1) by limiting macroscopic plastic deformations, which results in strain hardening, and (2) by reducing contractive microstructure reorganizations, which reduces the gap between the associated and non-associated flow rule directions. Fines content influences the plastic flow direction but has no influence on normal direction of yield surface. Eventually, perspectives on mesoscale mechanisms are given to highlight the role of fine grains in the geometrical and mechanical properties of granular materials.

     

Laboratory Investigation into the Effects of Silty Fines on Liquefaction Susceptibility of Chlef (Algeria) Sandy Soils

In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results.     

A compression model for sand–silt mixtures based on the concept of active and inactive voids

A compression model for sand–silt mixtures is needed in geotechnical engineering, for example in the analysis and prediction of deformation of levees and embankments due to internal erosion. In this paper, we introduce a novel concept of dividing the voids of a granular material into two hypothetical fractions: active and inactive voids. The active voids are kinematically available to the compression process. The inactive voids are kinematically unavailable to the compression process. The volume of active voids is dependent on the initial density and effective stress level. The volume of inactive voids is dependent on the amount of fines in the mixture. The current paper considers 1-D and isotropic compression behavior of sand–silt mixtures at stress levels lower than 2 MPa, so no substantial particle breakage is expected to occur. To successfully predict the void ratio for a sand–silt mixture during compression loading, we need (1) a mathematical expression for the evolution of the active void ratio during compression and (2) a relationship between the inactive void ratio and fines content of the mixture. For sand–silt mixtures with any amount of fines, the proposed model requires five material parameters, which are determined from two compression tests, and four minimum void ratio tests on sand–silt mixtures with different fines content. The performance of the proposed model is verified for six different types of sand–silt mixture with various fines contents, by comparing the predicted void ratios with the measured data from the experiments. The comparisons show a good agreement between the predictions and the measured data and prove the suitability of the proposed model for the prediction of compressibility of sand–silt mixtures with any amount of fines.     

The Direct Shear Strength and Dilatancy of Sand–gravel Mixtures

A total of 87 direct shear tests in a large direct shear-box apparatus have been used to investigate the strength and dilatancy of sand–gravel mixtures. This paper focuses on the differences in behaviour between a silica sand (yellow Leighton Buzzard sand) and sand–gravel mixtures obtained by adding fractions of two kinds of gravel to the sand. The purpose is to find a relation between the grain-size characteristics of the materials and the shearing resistance. Experimental results are analysed in terms of the frictional and dilatant contributions to the strength of mixtures as a function of their relative density, and are compared with dilatancy theories and empirical equations. The addition of gravel to the mixtures, even at low fractions (less than 0.1 by volume), causes an increase in peak friction angle (Φ ′_peak) which results both from higher dilatancy at failure (ψ_max) and higher constant volume friction angle (Φ ′_cv). Use of the minimum voids ratio (e_min) of the materials allows the data for the two families of mixtures to be normalized and interpreted in terms of Φ ′_cv and the ratio (Φ ′_peak − Φ ′_cv)/ψ_max. The relationships between relative density (D_r), ψ_max and Φ ′_peak − Φ ′_cv are only partly explained on a physical basis, so we develop empirical equations to predict the peak shear resistance of sand–gravel mixtures (up to gravel contents of 0.5) on the basis of easily measurable quantities. Such equations constitute a practical tool to overcome the problems arising from the impracticality of testing coarse material in the standard shear-box apparatus.     

Comprehensive laboratory study on stress–strain of granular soils at constant global void ratio: combined effects of fabrics and silt content

The published literature has revealed conflicting results regarding the effect of low plastic fines fraction (I_p?≤?5.0%) on the mechanical behavior of sandy soils. For this reason, the use of different sample initial structures as (initial relative density approach, global void ratio index approach, etc.) could explain these different mechanical responses of granular materials. Thus, it is necessary to evaluate the quantitative aspect of the low plastic fines effects on the undrained monotonic response of sand-silt mixtures using the global void ratio approach. To achieve this goal, an experimental testing program through controlled monotonic triaxial tests was carried out on reconstituted saturated Chlef sand containing from 0 to 50% silt with an interval of 10% at three global void ratios (e?=?0.64, 0.66 and 0.68) and subjected to constant confining pressure (σ'₃?=?100 kPa). The different samples were reconstituted using two different preparation techniques: DFP and MT. The obtained results show that the low plastic fines content appears as a very relevant parameter in the characterization of the mechanical response of sand-silt mixture samples reconstituted at constant global void ratios, where the steady state shear strength and instability shear strength decreased with the increase in low plastic fines content up to the limiting fines contents (F_c?=?40% and F_c?=?10%) considering both studied initial structures (Dry funnel pluviation and Moist tamping), respectively. Beyond these thresholds fines contents, a reverse trend was observed for all parameters under study. Moreover, the test results indicate that the brittleness index, flow potential (V_f), friction index, equivalent void ratio (e*) and equivalent relative density (Dr*) could be considered as reliable parameters in the prediction of the mechanical behavior of the silty sand soils under study.

     

Dominant grains network and behavior of sand–silt mixtures: stress–strain modeling

Stress–strain modeling of sand–silt mixtures is important in the analysis and design of earth structures. In this paper, we develop a stress–strain model that can predict the behavior of sand–silt mixtures with any amount of fines content. This model is based on a micromechanics approach, which involves mean‐field assumptions. For the mixtures with low amount of fines, the mechanical behavior is dominated by sand grains network. On the other hand, for the mixtures with high amount of fines, the mechanical behavior is dominated by silt grains network. Using this concept of dominant grains network, the behavior of mixtures with any amount of fines can be predicted from knowing the behavior of sand and silt, alone. We also modeled the critical state friction angle, critical state void ratio, and elastic stiffness for the mixtures as a function of fines content. The applicability of this developed stress–strain model is shown by comparing the simulated and measured results for two different types of sand–silt mixtures with full range of fines content. Copyright © 2012 John Wiley & Sons, Ltd.     

Evaluation of hydraulic conductivity of gap-graded granular soils based on equivalent void ratio concept

Gap-graded granular soils are used as construction materials worldwide, and their hydraulic conductivity depends on their relative content of coarse and fine grains, initial conditions, and particle shape. In this study, a series of constant head hydraulic conductivity tests were performed on gap-graded granular soils with different initial relative densities, fine contents, and particle shapes. The test results show that the hydraulic conductivity decreases with an increase in fine fraction and then remains approximately constant beyond the “transitional fine content.” The role of the structural effect on the hydraulic conductivity is different from that on the mechanical properties (such as stiffness and shear strength). This can be attributed to the degree of filling within inter-aggregate voids, disturbance of soil structure, and densified fine bridges between coarse aggregates. The equivalent void ratio concept was introduced into the Kozeny–Carman formula to capture the effect of fines (aggregates) on the “coarse-dominated” (“fine-dominated”) structure, and a simple model is proposed to capture the change of hydraulic conductivity of gap-granular soils. The model incorporates a structural variable to capture the effect of fines on “coarse-dominated” structure and coarse aggregates on “fine-dominated” structure. The performance of the model was verified with experimental data from this study and previously reported data compiled from the literature. The results reveal that the proposed model is simple yet effective at capturing the hydraulic conductivity of gap-graded granular soils with a wide range of fine contents, initial conditions, and particle shapes.

     

Undrained shear strength response under monotonic loading of Chlef (Algeria) sandy soil

During the last mid-century, the Chlef area was strongly affected by two earthquakes. From the geological context, there were numerous ejections onto the ground level of great masses of sandy soils and large displacements of various forms of some building foundations. These damages are due to soil liquefaction problem. This loss of shear strength can be attributed to many factors. History of recent cases indicates that sand deposited with silt content is much more liquefiable than clean sand. Therefore, a deep understanding of silty sand behavior is needed for the liquefaction assessment of silty sandy soils. Moreover, during seismic shaking, the post-liquefaction behavior of silty sand and, consequently, the stability of structures founded on liquefied soil depend on the steady-state shear strength of soil. The objective of this laboratory investigation is to show the effect of silt contents and the relative density on the mechanical behavior of such soils in monotonic loading. In this context, a series of undrained triaxial tests were performed on reconstituted saturated silty sand samples with different fines content ranging from 0% to 40%. In all tests, the confining pressure was held constant to 100 kPa. The fines content and the global void ratio are expressed by means of the equivalent void ratio. Linear correlations relating the undrained residual shear strength of loose, medium dense, and dense (D _r?=?12%, 50%, and 90% before consolidation) sand–silt mixtures to the equivalent void ratio are obtained. The concept of the equivalent void ratio will then be used as a key parameter to express the dilatancy behavior of both clean and silty sand soils. Moreover, from the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not represent the actual behavior of the soil as well.     

Practical Estimates of Tensile Strength and Hoek–Brown Strength Parameter m i of Brittle Rocks

By applying the Griffith stress criterion of brittle failure, one can find that the uniaxial compressive strength (σ_c) of rocks is eight times the value of the uniaxial tensile strength (σ_t). The Griffith strength ratio is smaller than what is normally measured for rocks, even with the consideration of crack closure. The reason is that Griffith’s theories address only the initiation of failure. Under tensile conditions, the crack propagation is unstable so that the tensile crack propagation stress (σ_cd)_t and the peak tensile strength σ_t are almost identical to the tensile crack initiation stress (σ_ci)_t. On the other hand, the crack growth after crack initiation is stable under a predominantly compressive condition. Additional loading is required in compression to bring the stress from the crack initiation stress σ_ci to the peak strength σ_c. It is proposed to estimate the tensile strength of strong brittle rocks from the strength ratio of R = \fracs_\textc | s_\textt | = 8\fracs_\textc s_\textci . R = {\frac{{\sigma_{\text{c}} }}{{\left| {\sigma_{\text{t}} } \right|}}} = 8{\frac{{\sigma_{\text{c}} }}{{\sigma_{\text{ci}} }}}. The term \fracs_\textc s_\textci {\frac{{\sigma_{\text{c}} }}{{\sigma_{\text{ci}} }}} accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. \fracs_c s_ci {\frac{{\sigma_{c} }}{{\sigma_{ci} }}} depends on rock heterogeneity and is larger for coarse grained rocks than for fine grained rocks. σ_ci can be obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from | s_\textt | = \fracs_\textc R = \fracs_\textci 8. \left| {\sigma_{\text{t}} } \right| = {\frac{{\sigma_{\text{c}} }}{R}} = {\frac{{\sigma_{\text{ci}} }}{8}}. It is found that the predicted tensile strengths using this method are in good agreement with test data. Finally, a practical estimate of the Hoek–Brown strength parameter m _i is presented and a bi-segmental or multi-segmental representation of the Hoek–Brown strength envelope is suggested for some brittle rocks. In this fashion, the rock strength parameters like σ_t and m _i, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.     

原位激发微生物成矿加固钙质砂的剪切与压缩特性研究

钙质砂广泛分布于热带海岸地区,其抗剪强度较低,在较高应力条件下极易破碎。因此,对以钙质砂为主要原料的地基材料进行加固,是海洋岩土工程领域的研究热点。基于尿素水解过程的碳酸钙成矿技术（MICP）是近年来地基材料加固领域的一项新技术。目前广泛使用的生物强化法实现MICP存在成本昂贵及环境适应性差等问题,制约了其大规模工程应用。研究采用原位生物激发MICP法对钙质砂进行加固,并对加固后试样开展直剪和一维压缩试验。结果表明：原位生物激发MICP方法可以在钙质砂中形成有效胶结,胶结水平最大可达6.26%。采用高浓度胶结溶液或增加注射次数可提高胶结水平。同时,加固后钙质砂的最大应力比、最大剪胀角以及残余内摩擦角均随胶结水平增加而显著增大,但竖向应力水平增大会抑制这些力学指标的增大。随胶结水平升高,试样压缩性显著减小;压缩后的原位激发MICP加固钙质砂中,细颗粒与粗颗粒的比例均随胶结水平的增加而增大。     

Initial motion and pivoting characteristics of sand particles in uniform and heterogeneous beds: experiments and modelling

Experiments are described in which the threshold conditions for sediment entrainment are measured for uniform and mixed sand beds beneath both steady and combined steady/oscillatory flows. Derived critical shear stresses are compared with the mixed bed entrainment model of Wiberg & Smith (1987). As predicted by the model, coarser grains within a sand mixture are entrained at lower bed shear stresses than progressively finer grains. Entrainment occurs generally at lower shear stresses than predicted by the model, especially under unidirectional flows. This may be the result of grains resting in unusually unstable positions during the experiments because the beds are ‘unworked’ at the start of the experiments. The model of Wiberg and Smith predicts threshold conditions more accurately for the mixed beds if the bed pivoting angle is correctly defined. The pivoting angles of the beds used here are measured using a new technique designed specifically for comparison with the threshold data. The measured angles repeat the finding that the coarse grains are more mobile than the finer fractions of a mixture. The results are poorly described by the pivoting angle model presented by Wiberg & Smith (1987) and are better represented by a model of the form Φ = αD^γ(D_i/D₅₀)^β (after 21 ), where α, γ and β are empirical constants. The threshold model is found to be more effective using the improved pivoting relationship. The entrainment of grains is found to be easier beneath unidirectional flows than combined flows, in accordance with previous authors’ findings. A suggestion that this result is caused by a change in the erosion mechanism beneath wave flows is made. Wave boundary layers may act as an extended laminar sublayer over bed grains and reduce the erosive efficiency of the overlying current flow. The results of the experiment have implications for the natural sorting mechanisms of sediment beds being deposited in near-threshold flows.