冲击荷载作用下软土隧道结构热-流-固耦合动力响应分析

爆炸对结构物的作用可以看成是冲击力和热的共同作用结果。基于Biot热弹性波动理论,利用饱和多孔介质热- 流-固耦合动力响应模型,研究了饱和软黏土中隧道结构内受指数衰减热/力冲击荷载作用下的动力响应。利用Flügge薄壳理论,得到隧道结构的运动方程。考虑土-结构接触面上的协调条件并利用热-流-固耦合动力响应模型的通解,得到了热/力冲击荷载作用下应力、位移和孔隙水压力响应在Laplace变换域中的解。利用Laplace数值逆变换技术得到数值计算结果,探讨了冲击荷载和热荷载作用下隧道结构刚度和厚度对应力、位移和孔隙水压力响应的影响。结果表明：在爆炸冲击荷载作用下,隧洞衬砌对周围土体起到很好的屏蔽作用,且衬砌刚度越大,其保护效果越好;衬砌与土体接触面上应力随衬砌刚度增大而减小,并且刚度越大应力衰减越快;衬砌刚度和厚度对热冲击的位移响应有明显影响,而对其温度响应的影响较小。     

基于滑块位移法大桩帽刚性短桩荷载传递特性分析

通过分析室内模型试验和数值模拟成果发现,随着荷载的不断增加,大桩帽刚性短桩桩帽下地基土体最终发生侧向整体剪切滑移破坏,而下部桩体则发生向下刺入破坏。据此,提出了一种滑块位移法分析桩帽下地基土体的荷载-位移关系,而下部桩体的荷载-位移关系则采用荷载传递法进行分析。然后,基于上、下两部分的位移协调条件,叠加得到大桩帽刚性短桩的荷载-位移关系曲线(P-s曲线)。同时,采用模型试验结果对此方法进行了验证,结果表明,采用此方法得到的P-s曲线与试验结果吻合良好。最后,利用本文计算模型分析了不同的帽桩直径比D/d以及桩长与桩帽直径比L/D对大桩帽刚性短桩承载力的影响,结果表明,在软土地基中宜采用帽桩直径比D/d2和桩长与桩帽直径比L/D10的带帽桩。     

冲击荷载下饱和软土动态响应特征的试验研究

基于现场动力排水固结法加固饱和软土地基工程实践和室内动力固结试验,结合土体压力分析了饱和软粘土在冲击荷载作用下的变形与孔压的发展变化规律。研究表明：冲击荷载引起土体变形和激发的孔压具有不同发展模式,土体变形与冲击击数是对数双曲线关系,而孔压与冲击击数之间仅是双曲线关系。     

冲击荷载下土体动力响应与加载速率效应研究

为揭示土体在冲击荷载作用下的动态响应特征,运用自主研发的附加激发力式平板动力载荷试验系统（flat dynamic load test,简称FDLT试验）对广州大学城区内两种典型土体（砂土和黏土）进行了不同荷载大小和加载速率的FDLT试验,获取了土体在冲击荷载下的荷载-时程曲线、位移-时程曲线、荷载-位移曲线的3种关系曲线。建立了动态变形模量与加载速率的经验公式,对比分析了两种土体在冲击荷载作用下的加载速率效应。研究表明：（1）砂土的FDLT试验存在一个充电量临界值,在该充电量冲击试验过程中,加载速率对砂土的动态强度及变形有较大的影响,而对黏土在本次试验条件下未有明显影响。（2）加载速率对黏土与砂土的位移响应的相同之处在于,最大荷载和最大位移均随加载速率的增大而提高;不同之处在于,黏土达到位移峰值时间会随加载速率增大而延长,而砂土达到位移峰值时间随加载速率增大呈现先增加后减小的规律。（3）土体的动态变形模量与加载速率曲线呈对数变化关系。本研究成果可为土体动力特性研究、土的动静参数换算和工程设计提供依据。     

基坑开挖与支护FLAC数值模拟计算及分析

介绍了FLAC-2D,根据基坑工程具体实例,采用FLAC-2D对基坑开挖及其支护结构状态进行计算和分析;并模拟了在未进行支护条件下的基坑开挖,得出了基坑土体在支护和未支护条件下,土体的应力状态、位移等值线图、位移矢量图、最终沉降量和结构受力.计算结果也证明了支护结构设计的合理性,对工程设计及施工分别起到了验证和预测的作用.     

饱和土体中空沟对移动荷载被动隔振的 2.5D边界元法分析

根据饱和土Biot理论及移动荷载特性,采用积分变换方法,推导了半无限饱和土体频域-波数内的边界积分方程,讨论了2.5D边界积分方程中Cauchy的奇异性,并分析了空沟对移动荷载引起饱和土体振动的被动隔振效果。通过与已知文献结果比较,验证了算法的正确性。数值结果表明,采用2.5D BEM不仅可以解决具有复杂表面的移动荷载作用下动力响应问题,而且可极大减小计算工作量。对于饱和土体受高速移动荷载作用,空沟更能有效减小土体孔压、竖向位移的振幅;当荷载速度较小时,空沟对土体表面的水平向位移几乎不起衰减作用,甚至有放大效应。另外,随空沟距振源的距离增大,空沟能够更好阻隔土体表面波传播。     

干砂强夯动力特性的细观颗粒流分析

通过引进和开发二维颗粒流程序,基于相似理论建立了可以模拟砂土地基强夯加固的细观颗粒流模型,结合小比尺室内细观模型试验,从颗粒细观力学角度入手对干砂在强夯冲击加固过程中的动力反应特性进行了数值模拟。结果表明,数值模拟结果与试验结果有较好的一致性,利用颗粒流模型可以很好地模拟干砂在冲击荷载作用下的锤底动接触应力、颗粒间动接触应力和颗粒位移场分布情况,并可以实时跟踪颗粒的变位及接触应力变化,实现从细观角度揭示干砂强夯动力响应特性,研究工作为今后砂土强夯加固宏细观机制研究提供了一条新的思路。     

强夯加固地基的土体竖向位移计算方法研究

根据动力分析中应力边界与速度边界之间的关系,将应力边界时程转化为速度边界时程,提出计算土体竖向位移的新方法,并进行了简化和多角度对比性研究。在钱家欢加卸载模型应力和竖向位移计算的基础上,提出将正弦荷载形式和三角形荷载形式分别引入,推导出竖向位移的两种简化计算方法。两种方法概念清楚、物理意义明确,形式简单且相同,区别仅在于系数不同。工程实例表明,两种方法计算出的竖向位移均接近于实测位移,但正弦荷载形式下的位移计算方法更能反映实际情况。     

低应变动测基桩承载力相对位移法初探

桩土体系受自由落锤冲击后,桩头所产生的相对位移,是桩土体系动刚度对作用荷载之间的动力响应。基桩低应变动测中,采用速度传感器直接测出桩头的相对位移,在推算单桩竖向承载力时,有助于降低对桩土体系固有频率测定值的过分依赖,从而有利于提高单桩竖向承载力推算值的准确程度。     

考虑几何非线性的强夯流固动力耦合分析

针对强夯法加固地基机理的流固动力耦合分析问题,本文考虑土体的几何非线性,建立土体非线性动力平衡方程和整体流固动力耦合方程,给出土体非线性动力平衡方程的迭代计算格式和流固动力耦合方程的解耦计算方法,并对一具体算例进行了数值分析,得到了地基位移、应力等在强夯作用下的变化规律和在空间上的分布特征,为精确模拟分析强夯加固机理提供了有效途径。     

Discontinuous analysis of softening solids under impact loading

Softening solids are analysed under impact loading using a new numerical method which allows displacement discontinuities to propagate arbitrarily through a finite element mesh. The Dirac‐delta distributions that arise in the strain field of classical continuum theory in the presence of strain softening are interpreted as discontinuities in the displacement field. A new finite element procedure with Heaviside jumps added to the underlying displacement interpolation basis is able to capture displacement jumps independent of the spatial discretisation. The amplitudes of displacement jumps are represented by extra degrees of freedom at existing nodes. Numerical results for mode‐I and mode‐II failure due to impact loading are presented. The numerical results highlight the objectivity of the approach with respect to spatial discretisation under dynamic loading conditions. Copyright © 2001 John Wiley & Sons, Ltd.     

基于振动台试验的加速度积分位移方法可靠性研究

土体应变变形是土工测试技术的重要难题之一,加速度积分位移是目前动荷载下原位监测和模型试验中认识土体剪应变响应的一种普遍方法,但缺乏验证与可靠性研究。设计砂质边坡?摇臂?质量块振动台模型试验,实测两地震荷载下多组工况的质量块加速度与位移响应时程,探讨了4种代表性方法求解动态、永久位移的可靠性及偏转影响。结果表明,动态位移求解采用高通滤波是一种可靠途径且受积分方式影响较小,各方法在动态位移工况中积分位移与实测相比,峰值平均误差小于等于25%;双拟法积分位移发生严重偏离,与函数形式和处理过程相关。永久位移求解采用高通滤波导致加速度低频成分缺失而无法得到永久位移;双拟法积分位移与实测相比吻合较好,两地震荷载中误差分别为7%和5%;偏转对动态位移求解可靠性影响较小,但对永久位移影响严重,双拟法呈现发散而失真。试验方法与结论,对认识加速度积分位移求取土体剪应变的可靠性和合理选取数据分析方法具有重要科学价值和指导意义。     

Experimental Investigation of Reinforced Soil Slopes in a Geotechnical Centrifuge,with the Use of Optical Fibre Sensors

The purpose of this experimental investigation is to obtain strain measurements via optical fibre sensors in the drum geotechnical centrifuge of ETH Zurich. It is part of a test series with main goal to study the behaviour of reinforced slopes subjected to self weight loading and subsequently to an impact from a rockfall event. In total 13 scaled reinforced slope models were built with a height of 180 mm and a slope inclination of 2V:1H, optimising the materials used and the different ways of model making. The maximum g-levels were 50 and 100 g and the impact loading was applied at 50 g. The optical fibre sensors were placed on various layers of the reinforcement and at different positions. Strain measurements that were recorded during different tests are logical and expected, demonstrating that optical fibre sensors can successfully be used for measuring linear strain on reinforcement layers that are tested under enhanced gravity in the geotechnical centrifuge. The experimental set up as well as the opportunities and challenges of these measurements are presented and discussed. Finally, correspondent prototype numerical models were created and analysed and the results of this analysis are compared to the corresponding experimental ones.     

初始应力条件对松砂动力变形特性影响的试验研究

实际建筑物地基或土坡中土体在地震或波浪等复杂动力荷载作用前往往处于复杂的初始应力状态,而常规的土工动力试验通常无法再现这种复杂固结应力条件下土的动力特性。利用最新研制开发的土工静力-动力液压三轴-扭转多功能剪切仪,针对福建标准砂（ %）,进行了循环扭剪试验,探讨了初始主应力方向角 和初始偏应力比 等初始固结条件对松砂动剪切模量G和阻尼比 等动力变形特性的影响。     

Seismic response analysis of geosynthetic reinforced soil segmental retaining walls by finite element method

The paper presents the results of a finite element analysis of the dynamic response of a geosynthetic reinforced soil retaining wall that is constructed with dry-stacked modular concrete blocks as the facia system. In the finite element model, the cyclic shear behavior of the backfill soil is described by a hyperbolic stress-strain relationship with Masing hysteretic unload-reload behavior. The reinforcement material is modelled using a similar hysteretic model which takes into account the measured response of cyclic load-extension tests performed on unconfined geogrid specimens in the laboratory. Interface shear between wall components is simulated using slip elements. The results of finite element analyses giving the seismic response of a typical geogrid reinforced segmental retaining wall subjected to prescribed acceleration records are presented. The results of analyses highlight the influence of dynamic loading on: (1) wall displacement; (2) cumulative interface shear force and displacement between facing units; (3) tensile forces developed in the reinforcement and; (4) acceleration response over the height of the wall. A number of implications to the design of these structures are identified based on the results of these simulations.     

卸围压下砂岩力学特性及细观机制颗粒流分析

鉴于试验砂岩内摩擦角较大及峰后脆性强的特点,选用颗粒流程序PFC2D中的cluster单元进行模拟,在常规三轴压缩试验校正的基础上得到一组能够真实反映砂岩宏观力学行为的细观参数,模拟了砂岩两种卸围压路径,结果表明其峰值强度随初始轴向应力的增大而不断增大,其规律与试验相同。选取了两种卸围压路径微裂纹数目随应力-应变的演化趋势进行分析,结果表明卸围压对试样造成的损伤较加轴压大,同时初始轴向应力增大一定程度上增加了试样承受破坏的能力。通过对不同应力路径裂纹两侧位移场的分析可知卸围压会造成颗粒在横向产生位移不连续,导致试样破坏。     

动荷载下桩承式路堤的承载特性及机制研究

对于桩承式路堤作用效应的研究目前主要侧重于对静荷载作用下桩土应力比和土拱效应等,较少考虑动荷载的影响,而车辆运行产生的动应力会对路堤中的土拱产生一定的影响,进而影响桩承式路堤的整体性能。为了分析静、动荷载作用下桩承式加筋路堤的性能变化,采用可视化模型试验和颗粒流数值模拟相结合的方法,对桩承式路堤在静载和动载下的应力传递和变形性状进行研究,分析动载作用下填土高度、桩帽、桩距、加筋形式、荷载频率的影响。试验结果表明,在动载下无筋路堤的桩顶的应力减小,而桩间的应力和位移增大,并且变化的幅度均比加筋路堤大,加筋材料的设置有利于减小动载的影响效应,但不同加筋形式下桩承式路堤的工作性状有所不同,受动载影响程度的大小主要与土拱效应的强弱有关。设置双层加筋时,因加筋材料与周围砂土形成半刚性平台,土拱效应减弱,故受动载影响的程度最小,单层加筋时,格栅设于桩顶上方10 cm比格栅置于桩顶受动载影响的程度明显减小,颗粒流的模拟结果验证了以上结果,并且进一步得出随荷载频率的增加、填土高度与桩净距的减小,动载的影响效应增大的结论。     

Serviceability limit state design for uplift of helical anchors in clay

Presently, no displacement-based design methodology exists for helical anchors subjected to tensile or uplift loading. This study investigates the statistical and probabilistic aspects of the load-displacement uncertainty associated with a database of thirty-seven uplift loading tests of helical anchors founded within cohesive soils. Initially, an ultimate resistance model is identified, and the semi-empirical uplift breakout factor statistically characterized. A relationship between ultimate resistance and slope tangent capacity is established, and used to form the basis for normalizing the load-displacement response. Hyperbolic and power law models are statistically evaluated for use in serving as a reference load-displacement model; the hyperbolic curve was selected based on goodness-of-fit statistics. Monte Carlo reliability simulations are used to establish an equivalent-deterministic load factor that associates the selected load factor with a probability of exceeding a pre-determined allowable uplift displacement, given uncertainty in the undrained shear strength, ultimate resistance model, transformation uncertainty, uncertainty in the allowable displacement, and variability in uplift loading. A practical example is provided to show the intended use of this probabilistic helical anchor displacement model.     

Analysis of piles subjected to lateral soil movements using a three‐dimensional displacement approach

An analytical approach using the three‐dimensional displacement of a soil is investigated to provide analytical solutions of the horizontal response of a circular pile subjected to lateral soil movements in nonhomogeneous soil. The lateral stiffness coefficient of the pile shaft in nonhomogeneous soil is derived from the rocking stiffness coefficient that is obtained from the analytical solution, taking into account the three‐dimensional displacement represented in terms of scalar potentials in the elastic three‐dimensional analysis. The relationship between horizontal displacement, rotation, moment, and shear force of a pile subjected to lateral soil movements in nonhomogeneous soil is obtainable in the form of the recurrence equation. For the relationship between the lateral pressure and the horizontal displacement, it is assumed that the behavior is linear elastic up to lateral soil yield, and the lateral pressure is constant under the lateral soil yield. The interaction factors between piles subjected to both lateral load and moment are calculated, taking into account the lateral soil movement. The formulation of the lateral displacement and rotation of the pile base subjected to lateral loads in nonhomogeneous soils is presented by taking into account the Mindlin equation and the equivalent thickness for soil layers in the equivalent elastic method. For lateral movement, lateral pressure, bending moment, and interaction factors, there are small differences between results obtained from the 1‐D and the 3‐D displacement methods except a very flexible pile. Copyright © 2015 John Wiley & Sons, Ltd.     

粉煤灰土冻融循环后的动力特性试验研究

为研究粉煤灰土作为路基填料的可行性，把易液化的粉煤灰和易冻胀的粉质黏土按干重1：2混合，通过冻融循环后的动三轴试验，研究了粉煤灰土的动力特性，得出了动强度和循环荷载次数及冻融循环次数的数量关系，以及动模量与动应变及冻融循环次数的关系曲线。研究表明，粉煤灰土经过3次冻融后的动力性能指标优于粉质黏土，具有良好的抗冻性及稳定性，可以作为季冻区路基填料。