Meso-scale testing and development of test procedures to maintain mass balance

The Conrad Blucher Institute for Surveying and Science (Texas A&M University––Corpus Christi) has conducted numerous petroleum experiments at the Shoreline Environmental Research Facility (Corpus Christi, Texas, USA). The meso-scale facility has multiple wave tanks, permitting some control in experimental design of the investigations, but allowing for real-world conditions. This paper outlines the evolution of a materials balance approach in conducting petroleum experiments at the facility. The first attempt at a materials balance was during a 1998 study on the fate/effects of dispersant use on crude oil. Both water column and beach sediment samples were collected. For the materials balance, the defined environmental compartments for oil accumulation were sediments, water column, and the water surface, while the discharge from the tanks was presumed to be the primary sink. The “lessons learned” included a need to quantify oil adhesion to the tank surfaces. This was resolved by adhering strips of the polymer tank lining to the tank sides that could be later removed and extracted for oil. Also, a protocol was needed to quantify any floating oil on the water surface. A water surface (oil slick) quantification protocol was developed, involving the use of solid-phase extraction disks. This protocol was first tested during a shoreline cleaner experiment, and later refined in subsequent dispersant effectiveness studies. The effectiveness tests were designed to simulate shallow embayments which created the need for additional adjustments in the tanks. Since dispersant efficacy is largely affected by hydrodynamics, it was necessary to scale the hydrodynamic conditions of the tanks to those expected in our prototype system (Corpus Christi Bay, Texas). The use of a scaled model permits the experiment to be reproduced and/or evaluated under different conditions. To minimize wave reflection in the tank, a parabolic wave dissipater was built. In terms of materials balance, this design reduced available surface area as a sink for oil adsorption.     

Study of the effect of water-soluble fractions of heavy-oil on coastal marine organisms using enclosed ecosystems,mesocosms

Mesocosm facilities composed of 4 experimental and 2 reservoir tanks (1.5 m in diameter, 3.0 m in depth and 5 tons in capacity) made of FRP plastics, were constructed in the concrete fish rearing pond in the Fisheries Laboratory, The University of Tokyo. The water-soluble fraction of Rank A heavy residual oil was formed by mixing 500 g of the oil with 10 l of seawater, which was introduced to the 5000 l-capacity tanks. Experimental Run 4 was conducted from May 31 to June 7, 2000. Oil concentrations in the tanks were 4.5 microg/l called LOW, and 13.5 microg/l, called HIGH tank. Bacterial growth rates very quickly accelerated in the HIGH tank just after the loading of oil which corresponded with a high increase of bacterial cells in the same tank after 2 days. Later, bacterial numbers in HIGH tank rapidly decreased, corresponding with the rapid increase of heterotrophic nano-flagellates and virus numbers on the same day. Sediment traps were deployed at the bottom of the experimental tanks, and were periodically retrieved. These samples were observed both under light microscope and epi-fluorescent microscope with UV-excitation. It was observed that the main components of the vertical flux were amorphous suspended matter, mostly originating from dead phytoplankton and living diatoms. It was further observed from the pictures that vertical transport of oil emulsions were probably conducted after adsorption to amorphous suspended matter and living diatoms, and were settling in the sediment traps at the bottom of the tanks. This means that the main force which drives the soluble fraction of oil into bottom sediment would be vertical flux of such amorphous suspended particles and phytoplankton. Further incubation of the samples revealed that the oil emulsions were degraded by the activity of autochtonous bacteria in the sediment in aerobic condition.     

Effects of oil dispersants on settling of marine sediment particles and particle-facilitated distribution and transport of oil components

This work investigated effects of three model oil dispersants (Corexit EC9527A, Corexit EC9500A and SPC1000) on settling of fine sediment particles and particle-facilitated distribution and transport of oil components in sediment-seawater systems. All three dispersants enhanced settling of sediment particles. The nonionic surfactants (Tween 80 and Tween 85) play key roles in promoting particle aggregation. Yet, the effects varied with environmental factors (pH, salinity, DOM, and temperature). Strongest dispersant effect was observed at neutral or alkaline pH and in salinity range of 0–3.5 wt%. The presence of water accommodated oil and dispersed oil accelerated settling of the particles. Total petroleum hydrocarbons in the sediment phase were increased from 6.9% to 90.1% in the presence of Corexit EC9527A, and from 11.4% to 86.7% for PAHs. The information is useful for understanding roles of oil dispersants in formation of oil-sediment aggregates and in sediment-facilitated transport of oil and PAHs in marine eco-systems.     

Assessment of chemical dispersant effectiveness in a wave tank under regular non-breaking and breaking wave conditions

Current chemical dispersant effectiveness tests for product selection are commonly performed with bench-scale testing apparatus. However, for the assessment of oil dispersant effectiveness under real sea state conditions, test protocols are required to have hydrodynamic conditions closer to the natural environment, including transport and dilution effects. To achieve this goal, Fisheries and Oceans Canada and the US Environmental Protection Agency (EPA) designed and constructed a wave tank system to study chemical dispersant effectiveness under controlled mixing energy conditions (regular non-breaking, spilling breaking, and plunging breaking waves). Quantification of oil dispersant effectiveness was based on observed changes in dispersed oil concentrations and oil-droplet size distribution. The study results quantitatively demonstrated that total dispersed oil concentration and breakup kinetics of oil droplets in the water column were strongly dependent on the presence of chemical dispersants and the influence of breaking waves. These data on the effectiveness of dispersants as a function of sea state will have significant implications in the drafting of future operational guidelines for dispersant use at sea.     

东太湖沉积物中多环芳烃-菲系列化合物的来源探讨

本文用索氏抽取法提取了东太湖的沉积物和水生植物中的可溶性有机质,用不同极性溶剂在硅胶／氧化铝柱上分离了饱和烃、芳烃、酮馏分,利用GC-MS至芳烃组分进行了鉴定分析,并对其中重要多环芳烃－菲系列化合物的来源进行了探讨。     

Oil droplet interaction with suspended sediment in the seawater column: Influence of physical parameters and chemical dispersants

The interaction of dispersed oil droplets with large diameter suspended particulate materials (SPM) has been little studied. In the current study, particle size, oil characteristics and chemical dispersant significantly influence the adsorption of oil droplets to SPM in seawater. Sediments with a smaller particulate size (clay) approaching that of the oil droplets (2–20 μm) adsorbed more oil per gram than sediments with large particle size (sand). Heavier, more polar oils with a high asphaltene content adsorbed more efficiently to SPM than lighter, less polar oils. A decrease in the smaller, more water soluble oil components in the sediment adsorbed oil was observed for all oil types. Addition of chemical dispersant decreased the adsorption of oil droplets to suspended carbonate sand in an exponential-like manner. No change in the relative distribution of compounds adsorbed to the sediment was observed, indicating dispersants do not alter the dissolution of compounds from oil droplets.     

湖泊底泥疏浚对沉积物再悬浮及营养盐负荷影响的模拟

选取太湖梅梁湾污染底泥为研究对象,利用沉积物再悬浮发生装置,通过室内模拟实验研究太湖夏季常规风情下底泥疏浚对沉积物再悬浮及上覆水营养盐动态变化的影响.结果表明,在模拟的风情扰动过程结束时(5 h),扰动过程未疏浚与疏浚处理水柱总悬浮颗粒物(TSS)含量变化差异显著,未疏浚对照水柱TSS含量是初始值的7.7倍,而疏浚水柱TSS在第2 h达到峰值,为初始值的3.8倍;未疏浚水柱TSS含量沉降过程最初1 h迅速降低了84.0%,而疏浚水柱TSS含量在沉降3 h后趋于平衡.伴随着沉积物的再悬浮过程,疏浚与未疏浚对照水柱中TP含量均在第5 h达到最大,分别增加负荷78.6和92.2 mg/m2.就短时效而言,底泥疏浚后沉积物的再悬浮过程显著受到抑制,并能够显著地减小沉积物再悬浮过程中溶解性磷酸盐的释放;但对水柱中总磷、总氮、铵氮、硝酸盐和亚硝酸盐含量变化影响较小.     

Effect of dispersed crude oil exposure upon the aerobic metabolic scope in juvenile golden grey mullet (Liza aurata)

This study evaluated the toxicity of dispersant application which is, in nearshore area, a controversial response technique to oil spill. Through an experimental approach with juveniles of Liza aurata, the toxicity of five exposure conditions was evaluated: (i) a chemically dispersed oil simulating dispersant application; (ii) a single dispersant as an internal control of chemically dispersed oil; (iii) a mechanically dispersed oil simulating natural dispersion of oil; (iv) a water soluble fraction of oil simulating an undispersed and untreated oil slick and (v) uncontaminated seawater as a control exposure condition. The relative concentration of PAHs (polycyclic aromatic hydrocarbons) biliary metabolites showed that the incorporation of these toxic compounds was increased if the oil was dispersed, whether mechanically or chemically. However, toxicity was not observed at the organism level since the aerobic metabolic scope and the critical swimming speed of exposed fish were not impaired.     

Evaluating crude oil chemical dispersion efficacy in a flow-through wave tank under regular non-breaking wave and breaking wave conditions

Testing dispersant effectiveness under conditions similar to that of the open environment is required for improvements in operational procedures and the formulation of regulatory guidelines. To this end, a novel wave tank facility was fabricated to study the dispersion of crude oil under regular non-breaking and irregular breaking wave conditions. This wave tank facility was designed for operation in a flow-through mode to simulate both wave- and current-driven hydrodynamic conditions. We report here an evaluation of the effectiveness of chemical dispersants (Corexit^® EC9500A and SPC 1000^™) on two crude oils (Medium South American [MESA] and Alaska North Slope [ANS]) under two different wave conditions (regular non-breaking and plunging breaking waves) in this wave tank. The dispersant effectiveness was assessed by measuring the water column oil concentration and dispersed oil droplet size distribution. In the absence of dispersants, nearly 8-19% of the test crude oils were dispersed and diluted under regular wave and breaking wave conditions. In the presence of dispersants, about 21-36% of the crude oils were dispersed and diluted under regular waves, and 42-62% under breaking waves. Consistently, physical dispersion under regular waves produced large oil droplets (volumetric mean diameter or VMD ? 300 μm), whereas chemical dispersion under breaking waves created small droplets (VMD ? 50 μm). The data can provide useful information for developing better operational guidelines for dispersant use and improved predictive models on dispersant effectiveness in the field.     

Biodegradation of petroleum hydrocarbons at low temperature in the presence of the dispersant Corexit 9500

Our study examined the effects of Corexit 9500 and sediment on microbial mineralization of specific aliphatic and aromatic hydrocarbons found in crude oil. We also measured gross mineralization of crude oil, dispersed crude oil and dispersant by a marine microbial consortium in the absence of sediment. When provided as carbon sources, our consortium mineralized Corexit 9500 the most rapidly, followed by fresh oil, and finally weathered oil or dispersed oil. However, mineralization in short term assays favored particular components of crude oil (2-methyl-naphthalene > dodecane > phenanthrene > hexadecane > pyrene) and was not affected by addition of nutrients or sediment (high sand, low organic carbon). Adding dispersant inhibited hexadecane and phenanthrene mineralization but did not affect dodecane and 2-methyl-naphthalene mineralization. Thus, the effect of dispersant on biodegradation of a specific hydrocarbon was not predictable by class. The results were consistent for both high and low oiling experiments and for both fresh and weathered oil. Overall, our results indicate that environmental use of Corexit 9500 could result in either increases or decreases in the toxicity of residual oil through selective microbial mineralization of hydrocarbons.     

The settling of resuspended lake sediment related to physicochemical properties of particles of different sizes: Implication for environmental remediation

Sediment resuspension is an important way for shallow lake internal pollution to interact with the overlying water column,and the pollution risks are reasonably related to the retention of resuspended sediment particles in overlying water.In the current study,the settling of resuspended sediment particles was comprehensively investigated under different disturbances using five urban lake sediments.The results show that the particle size distributions of resuspended sediment from different lakes exhibited similar variations during settling with disturbance,although varied settling times were observed under static conditions.During settling with and without disturbance,sediment particle sizes were mainly within 8-63μm at the initial stage,and were<8μm in the later stages of settling.Based on these settling characteristics,the sediment particle size was divided into sand(>63μm),silt(8-63μm),and very fine silt and clay(<8μm)fractions.Kinetic analysis suggested that sediment settling for different particle sizes could be well described by the first-and second-order kinetic equations,especially when settling was disturbed(r²=0.727-0.999).The retention of resuspended sediment could be enhanced as particle sizes decreased and disturbance intensities increased.Furthermore,a water elutriation method was successfully optimized,with separation efficiencies of 56.1%-83%,to separate sediment particles into the defined three particle size fractions.The chemical compositions of sediment were found to change with different particle sizes.Typically,calcium tended to form large-size sediment,while the total contents of aluminum,iron,magnesium,and manganese showed significantly negative correlations with sediment particle sizes(p<0.01)and tended to distribute in small-size particles(e.g.,<8μm).Overall,the sediment particle size related settling dynamics and physicochemical properties suggested the necessity on determining the pollution of resuspended sediment at different particle sizes for restoration of shallow lakes.     

Anthropogenic organic contaminants in water, sediments and benthic organisms of the mangrove-fringed Segara Anakan Lagoon, Java, Indonesia

Segara Anakan, a mangrove-fringed coastal lagoon in Indonesia, has a high diversity of macrobenthic invertebrates and is increasingly affected by human activities. We found >50 organic contaminants in water, sediment and macrobenthic invertebrates from the lagoon most of which were polycyclic aromatic compounds (PACs). Composition of PACs pointed to petrogenic contamination in the eastern lagoon. PACs mainly consisted of alkylated PAHs, which are more abundant in crude oil than parent PAHs. Highest total PAC concentration in sediment was above reported toxicity thresholds for aquatic invertebrates. Other identified compounds derived from municipal sewage and also included novel contaminants like triphenylphosphine oxide. Numbers of stored contaminants varied between species which is probably related to differences in microhabitat and feeding mode. Most contaminants were detected in Telescopium telescopium and Polymesoda erosa. Our findings suggest that more attention should be paid to the risk potential of alkylated PAHs, which has hardly been addressed previously.     

Distribution and characteristics of PAHs in sediments from the Mediterranean coastal environment of Egypt

To assess the contamination of polycyclic aromatic hydrocarbons (PAHs) in the Mediterranean coastal environment of Egypt, 26 sediment samples from the coastline, harbours, estuaries and coastal lakes were collected and analyzed. The sediment PAH concentrations of thirty-nine 2-6 ring PAHs ranged from 13.5 to 22,600 ng/g. PAH profiles varied according to the nature of the site and its proximity to sources. Industrialized and urbanized region showed high level of PAHs contamination. In general, the contamination levels of PAHs were similar to those observed in contaminated and slightly contaminated sediments of the Mediterranean Sea. Molecular indices based on ratios of selected PAH concentrations were used to differentiate PAHs from pyrogenic and petrogenic and mixed origins. Good correlations were observed between the petrogenic index, MP/P, A-PAHs/P-PAHs and HMW/LMW. Finally, PAH levels in sediments were compared with Sediments Quality Guidelines (ERM-ERL) for evaluation of probable toxic effects on organism.     

巢湖西湖心底泥蓝藻对水体蓝藻生物量的贡献

2018年10月-2019年10月对巢湖西湖心水体浮游藻类群落结构以及水体和底泥蓝藻生物量进行了月度调查.结果表明:巢湖西湖心浮游藻类的主要优势种属为微囊藻属、席藻属、十字藻、卵形隐藻和鱼腥藻属.蓝藻优势种属在5-10月为微囊藻属,11-12月为鱼腥藻属,1-4月为席藻属.巢湖水体和底泥蓝藻生物量峰值分别出现在9月和2月,水体蓝藻的衰亡下沉会导致底泥蓝藻生物量的上升.巢湖蓝藻主要分布在水体,底泥蓝藻生物量相对较低,单位面积水柱与底泥蓝藻生物量6月的比值大于100,在11-3月相对较低,最低值小于2.底泥蓝藻主要分布在底泥表层0～2 cm.通过安装原位捕获器,监测了蓝藻在西巢湖湖心水柱和底泥中的垂直迁移过程和通量.结果表明:11月和2月蓝藻有明显从水柱向底泥迁移的过程;底泥蓝藻全年向水体的静态迁移量都很低,而动态迁移在11月和6月出现两个峰值,主要受底泥蓝藻生物量和再悬浮的影响.本研究结果表明削减巢湖西湖心底泥种源的最佳时期为10月至来年2月,但是由于底泥蓝藻生物量远远小于水柱蓝藻生物量,底泥蓝藻向水体复苏迁移的通量也较低,即使削减了底泥种源,也不能有效降低水体蓝藻生物量.     

Role of a moderately halophilic bacterial consortium in the biodegradation of polyaromatic hydrocarbons

Polycyclic aromatic hydrocarbons are ubiquitous pollutants in the environment, and most high molecular weight PAHs cause mutagenic, teratogenic and potentially carcinogenic effects. While several strains have been identified that degrade PAHs, the present study is focused on the degradation of PAHs in a marine environment by a moderately halophilic bacterial consortium. The bacterial consortium was isolated from a mixture of marine water samples collected from seven different sites in Chennai, India. The low molecular weight (LMW) PAHs phenanthrene and fluorine, and the high molecular weight (HMW) PAHs pyrene and benzo(e)pyrene were selected for the degradation study. The consortium metabolized both LMW and HMW PAHs. The consortium was also able to degrade PAHs present in crude oil-contaminated saline wastewater. The bacterial consortium was able to degrade 80% of HMW PAHs and 100% of LMW PAHs in the saline wastewater. The strains present in the consortium were identified as Ochrobactrum sp., Enterobacter cloacae and Stenotrophomonas maltophilia. This study reveals that these bacteria have the potential to degrade different PAHs in saline wastewater.     

Effectiveness and toxicity of an oil dispersant in large outdoor salt water tanks

Use of the dispersant, Oilsperse 43, increased the dispersion of Venezuelan Guanipa crude oil. The resulting mixture was more homogeneous and the oil slick less viscous than in the oil tank. The dispersant appeared to retard formation of the familiar “crust” on the surface. A weathered crude oil plus dispersant mixture with an oil concentration of 250 μg/l was lethal to over 50% of the test organisms, green sea urchins, within 4 days. No mortalities occurred among urchins exposed to the crude oil treatment.     

Persistence profile of polyaromatic hydrocarbons in shallow and deep Gulf waters and sediments: effect of water temperature and sediment-water partitioning characteristics

Persistence profiles of selected polyaromatic hydrocarbons (PAHs) were analyzed depending on temperature variations in the water column and water–sediment interactions in the Gulf of Mexico. The PAHs studied include anthracene, fluoranthene, pyrene, and chrysene. The half-lives of PAHs in the deep waters (over 1000 m) are about twice as long as those in the shallow areas (100–150 m), and almost 2.5 times as long as those in the top layer (0–10 m) of the water column. The half-lives of the PAHs in the sediments are significantly longer. Among the PAHs studied, chrysene is the most persistent in the water column, and pyrene is the most persistent in the sediments. The half-life of chrysene in the shallow and deep waters is over 2.5 and about 5 years, respectively. For pyrene, the half-life in the shallow and deep sediments is about 9 and 16 years, respectively.     

Spatial and temporal distribution of dissolved/dispersed aromatic hydrocarbons in seawater in the area affected by the Prestige oil spill

Seawater samples collected at three depths from 68 stations along the Northern Spanish coast were analysed for dissolved/dispersed petroleum aromatic hydrocarbons by UV-fluorescence and for 25 individual compounds by GC-MS. Sampling was performed in December 2002, just after the Prestige oil spill, and in February-March and September 2003. Higher concentrations of total aromatic hydrocarbons were found at all depths in the samples collected during December 2002 off the Galicia coast, with levels ranging between 0.19 and 28.8 microg/L eq. oil (0.1-4.8 microg/L chrysene eq.). These values decreased in the following cruises, till <0.05-2.86 microg/L oil eq. (av. 0.23 microg/L chrysene eq.) in September 2003, possibly representing the background levels for the region. However, in the Cantabrian coast they were still high at the surface in the March cruise, probably by the late arrival of the fuel-oil to this area. Some coastal hot spots were also identified, with values up to 29.2 microg/L fuel-oil eq., close to river mouths and urban areas. The individual PAH distributions in the December 2002 sampling off-Galicia were dominated by alkyl-naphthalene derivatives, consistently with the pattern distribution shown by the fuel-oil water accommodated fraction. The higher concentrations were found in the subsurface samples along the Costa da Morte, the area most heavily affected by the spill (av. 0.46 microg/L Sigma16 PAHs). The rest of the samples collected in other areas exhibited lower concentrations and a more even distribution of 2-4 ring PAHs, that ranged from 0.09 to 0.37 microg/L (av. 0.15 microg/L Sigma16 PAHs), with decreasing trends offshore and downward the water column. In September 2003, the values were rather uniform, averaging 0.09 microg/L (Sigma16 PAHs).     

Variation of turbidity during subsurface abstraction of river water: A case study

Rivers are known to carry sediment loads. Many rivers in Asia including Kosi, Brahmaputra, Bagmati rivers in India and Yellow and Yarlung Tsangpo rivers in China are well known for their carriage of excessive sediment loads. In India, many water abstraction units are located along river banks. Their success depends on how the sediment load is trapped as the sediment laden water flows towards the pumping wells located few hundred meters away from river bank. In this work, based on the analysis of a data of one year on suspended load variations in a canal, located at Haridwar, India, trap efficiency variations are studied during the passage of source water to the abstraction well. Considering the subsurface basin, located within the source water and the abstraction well, as a hypothetical settling basin, variation of trap efficiency is related with the influent concentration. It is observed that the trap efficiency depends on the influent concentration. Appropriate functional forms for the variation of trap efficiency with the influent concentrations are also identified.     

PAHs distribution in sediments associated with gas hydrate and oil seepage from the Gulf of Mexico

Six sediment samples collected from the Gulf of Mexico were analyzed. Total concentrations of the PAHs ranged from 52 to 403 ng g⁻¹ dry weight. The lowest PAH concentration without 5–6 rings PAHs appeared in S-1 sample associated with gas hydrate or gas venting. Moreover, S-1 sample had the lowest organic carbon content with 0.85% and highest reduced sulfur level with 1.21% relative to other samples. And, analysis of the sources of PAHs in S-1 sample indicated that both pyrogenic and petrogenic sources, converserly, while S-8, S-10 and S-11 sample suggested petrogenic origin. The distribution of dibenzothiophene, fluorine and dibenzofuran and the maturity parameters of triaromatic steranes suggested that organic matters in S-1 sample were different from that in S-8, S-10 and S-11 sample. This study suggested that organic geochemical data could help in distinguish the characteristic of sediment associated with gas hydrate or with oil seepage.