纳米 Fe2O3-SnO2 光催化降解海水养殖废水中的氨氮

通过共沉淀法制备纳米Fe_2O_3-SnO_2光催化剂,采用XRD、SEM等测试手段对其进行形貌、物象、粒径一系列的表征,研究结果显示制得的催化剂仍保持纯SnO_2四方金红石型结构.研究了Fe_2O_3-SnO_2光催化剂投加量、Fe_2O_3与SnO_2物质的量比、煅烧温度、煅烧时间、氨氮初始浓度、p H值、H2O2浓度以及光照反应时间等因素对海水养殖废水中氨氮降解效率的影响.在紫外光照射下进行正交实验,确定最优化反应条件:催化剂投加量为0.4 g/dm3,煅烧时间为3 h,物质的量比为1∶2,氨氮初始含量为50 mg/dm3,光照反应时间为2 h.这5个因素对Fe_2O_3-SnO_2光催化氧化速率影响的大小程度依次为:Fe_2O_3与SnO_2物质的量比煅烧时间Fe_2O_3-SnO_2光催化剂投加量氨氮初始浓度光照时间.氨氮去除率可以达到85.1%,相同条件可见光下也可达到82.3%.     

海洋真菌Rhodotorulamucilageinosa GIM 2.157介导邻-、间-、对-溴苯乙酮的不对称还原反应

研究了海洋真菌介导邻-、间-、对-溴苯乙酮的不对称还原反应。具体考察了Rhodotorulamucilageinosa GIM 2.157对邻-、间-、对-溴苯乙酮的催化活性和对映选择性,并综合考察了反应温度、pH、反应时间和底物浓度等因素对还原产物的产率及立体选择性的影响。确定最佳反应条件:反应温度为25℃,反应体系的pH为7,反应时间为24 h,底物浓度为10 mmol/L。在最佳条件下,产率以及立体选择性均99%。     

11-deoxyheloside A的合成

首次完成天然胆甾烷型皂苷11-deoxyheloside A的合成。在相转移催化的条件下,葡萄糖溴苷1与膦酸单乙酯2反应以69%的收率得到葡萄糖膦酸酯供体3;以胆甾烷苷元4为原料,经Luche还原和乙酰化反应以及三氟甲磺酸负载硅胶脱除TBDPS基团得到胆甾烷二醇10;在金催化剂的作用下,胆甾二醇10与葡萄糖膦酸酯供体3进行糖苷化反应,然后脱除酰基保护基以97%的产率完成11-deoxyheloside A的合成。     

宽礁膜多糖酸的水解条件

采用0.1 mol/L H2SO4对热水提宽礁膜多糖进行酸水解,研究了水解过程中不同的反应温度和反应时间对宽礁膜多糖分子量的影响。通过控制反应温度和反应时间,得到了分子量在155.0~3.9 kDa间的低分子量宽礁膜多糖。结果表明,反应温度的升高,反应时间的延长都有利于宽礁膜多糖分子量的降低,但温度较时间的影响要明显。     

酶解糙刺参内脏团蛋白制备抗氧化肽的工艺研究

为了能够有效利用糙刺参内脏蛋白,以水解度为主要指标,对酶解蛋白酶进行了筛选,并系统研究了酶解温度、p H、加酶量和水解时间等单因素对水解度的影响。在此基础上,利用响应面中心组合设计实验,对酶解工艺进行了优化,得到以温度、p H、加酶量及水解时间为因子的二次方程,通过方差分析和验证性实验得出,此二次方程能较好反应海参内脏团蛋白水解度的变化规律,得到最佳水解条件为:温度52.66℃,p H 6.71,加酶量2.5%(质量分数),酶解时间10 h,预测最高水解度为49.58%。最佳酶解条件下所得多肽74%以上分子质量小于500 Da。利用DPPH法测定最佳条件酶解所得多肽的抗氧化活性,3 g/L的抗氧化率达到了24.8%,利用ABTS法测定最佳条件酶解所得多肽的抗氧化活性,3 g/L的抗氧化率达到了0.255μmol/g。为海参内脏蛋白的利用提供了参考。     

可见光下Li+/CNTS-TiO2光催化剂降解海洋柴油污染的研究

通过溶胶-凝胶法,以CNTS-TiO₂为前驱物制备了Li⁺掺杂CNTS-TiO₂的纳米复合光催化剂(以下均称为Li⁺/CNTS-TiO₂),采用X射线衍射(XRD)、扫描电镜(SEM)等测试手段对光催化剂进行表征,结果表明制得的催化剂为纳米材料且在TiO₂的基础上增大了比表面积。利用掺杂量为3%的Li⁺掺杂CNTS-TiO₂复合光催化剂(以下均称为3%Li⁺/CNTS-TiO₂)光催化降解海洋柴油污染,在可见光条件下考察了Li⁺掺杂量、煅烧温度、光催化剂投加量、柴油初始质量浓度、光催化反应时间、H₂O₂质量浓度等条件对光催化实验的影响。进行正交实验,确定最优化工艺条件为:Li⁺掺杂量为3%,光催化剂的煅烧温度为600 ℃,3%Li⁺/CNTS-TiO₂的投加量为0.1 g/L,降解柴油初始质量浓度为0.4 g/L,光催化反应时间为3 h,H₂O₂质量浓度为0.6 g/L,降解率可以达到95%以上。同时对此光催化剂进行应用试验,试验结果表明光催化剂去除效果优异,去除率可达91.87%。     

改性沸石催化剂对油砂沥青的改质研究

本研究通过对天然斜发沸石进行HCl酸洗脱调节硅铝比,再负载Ni金属氧化物,经焙烧改性得到了同时具有对油砂沥青催化减黏、降低硫氮含量等性能的新型催化剂Clin-c,将该催化剂应用于新疆油砂沥青(露天含砂开采)和加拿大油砂沥青(蒸汽辅助重力泄油技术开采,SAGD)的改质反应。油砂沥青具有高黏度(~30 000cP,40℃)、高硫(0.56%~4.8%)、高氮(0.73%~2.38%)、高沥青质含量(34.64%)等特点。采用改性斜发沸石催化剂改质后,新疆油砂沥青剂油比1∶1,在340℃催化裂化反应30min,减黏率超过80%,脱氮率在45%~52%之间,脱硫率高于75%,同时大量非烃被催化裂化为轻质油。并用此优异的催化剂对加拿大油砂沥青进行了改质研究,剂油比1∶10发现减黏率超过75%,脱氮率在10%~32%之间。结果表明,改性斜发沸石催化剂对油砂沥青具有很好的催化减黏、脱硫氮性能。     

酶促反应制备壳寡糖及壳寡糖分析

用壳聚糖酶降解法对壳聚糖进行降解制备壳低聚糖，研究了温度、pH、底物浓度、脱乙酰度、反应时间对酶促反应的影响。对酶解产物进行HPLC分析，用Bio—Gel P-4柱对酶解产物进行初步分离。结果表明，壳聚糖酶降解壳聚糖的最适温度为45℃，pH为6．0，最适底物质量分数为6％，脱乙酰度越高酶解反应所得产物的数均相对分子质量越小，24h后酶解反应达到平衡，酶解产物壳寡糖水溶性极好。P-4柱分离得到聚合度20以上，10～20，10以下3种壳寡糖。     

纳米ZnO-La_2O_3固体碱的制备及其催化废弃煎炸油制备生物柴油

本文采用共沉淀法,以草酸铵为沉淀剂制备了ZnO-La2O3固体碱,并将其应用于催化废弃煎炸油与甲醇的酯交换反应制备生物柴油,通过X射线衍射(XRD)、电感耦合等离子体原子发射光谱(ICP-AES)以及扫描电子显微镜(SEM)对催化剂的组成和形貌进行表征。结果表明:700℃煅烧制备的催化剂具有较好的催化活性,催化剂是由ZnO和La2O3组成,锌镧摩尔比为3∶1,粒径在100nm左右。该催化剂用量5%(为油的质量)、醇油摩尔比36∶1、200℃反应3h,得到的脂肪酸甲酯(FAME)产率达到91.6%;催化剂经过洗涤和干燥,无需活化可继续使用,连续使用第四次后,脂肪酸甲酯的产率仍保持在80%以上。     

响应面法优化罗非鱼(Oreochromis niloticus)鱼排蛋白分段酶解工艺

采用生物蛋白酶酶解罗非鱼鱼排蛋白,以水解度(DH)为指标,进行了单酶、复合酶酶解效果的比较分析,并利用响应面分析方法(RSM)对酶解参数进行优化。结果表明,采用风味蛋白酶和木瓜蛋白酶双酶组合分段酶解,固定总酶添加量为3.0%、双酶复合比2:1、酶解时间3h、分段酶解时间比0.6:1,酶解温度56℃,分段酶解pH为7.0和6.2时,酶解效果最佳,罗非鱼鱼排蛋白水解度达到32.49%,酶解产物中游离氨基酸含量达32.84mg/g鱼排,占罗非鱼鱼排总氨基酸含量的25.43%,其中呈味氨基酸含量达18.48%,必需氨基酸含量达67.96%。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

Assessing the Validity of Seismo-Acoustic Predictor Equations for Obtaining Seabed and Sub-Surface Sediment Physical Properties

The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Interannual Sea Level Variations and Annual Tides in the Northwestern Pacific

Specific properties of the interannual sea level variations and annual tides in the Northwestern Pacific were studied. Several tide stations were monitored. The monthly mean sea level for the year of 1995 was analyzed at each tide station. A seismic event in 1995, some tectonic activity around the subject area, and the Kuroshio (the oceanic western boundary current) may possibly contaminate results which would have occurred from the astronomical annual tide alone.     

《Acta Oceanologica Sinica》Vol. 33(2014) contents

<正>~~