Development and parameterization of an infiltration model accounting for water depth and rainfall intensity

Experimental work has clearly shown that the effective hydraulic conductivity (K_e) or effective infiltration rate (f_e) on the local scale of a plot cannot be considered as constant but are dependent on water depth and rainfall intensity because non‐random microtopography‐related variations in hydraulic conductivity occur. Rainfall–runoff models generally do not account for this: models assume that excess water is uniformly spread over the soil surface and within‐plot variations are neglected. In the present study, we propose a model that is based on the concepts of microtopography‐related water depth‐dependent infiltration and partial contributing area. Expressions for the plot scale K_e and f_e were developed that depend on rainfall intensity and runon from upslope (and thus on water depth). To calibrate and validate the model, steady state infiltration experiments were conducted on maize fields on silt loam soils in Belgium, with different stages and combinations of rainfall intensity and inflow, simulating rainfall and runon. Water depth–discharge and depth–inundation relationships were established and used to estimate the effect of inundation on K_e. Although inflow‐only experiments were found to be unsuitable for calibration, the model was successfully calibrated and validated with the rainfall simulation data and combined rainfall–runon data (R²: 0.43–0.91). Calibrated and validated with steady state infiltration experiments, the model was combined with the Green–Ampt infiltration equation and can be applied within a two‐dimensional distributed rainfall–runoff model. The effect of water depth–dependency and rainfall intensity on infiltration was illustrated for a hillslope. Copyright © 2012 John Wiley & Sons, Ltd.     

Run off-on-out method and models for soil infiltrability on hill-slope under rainfall conditions

Infiltration is the process of water penetrating into soil, generally referred to as the downward movement of water from the soil surface[1,2]. This process is af-fected by water supply and the soil infiltrability, de-termines the amounts of water entering into soil pro-file and the surface runoff. Infiltrability is defined as the infiltration flux of a unit area under atmospheric pressure and sufficient water supply. The actual infil-tration rate and/or the infiltrability is expressed in m/s …     

Sediment and solute transport on soil slope under simultaneous influence of rainfall impact and scouring flow

Soil erosion and nutrient losses with surface runoff in the loess plateau in China cause severe soil quality degradation and water pollution. It is driven by both rainfall impact and runoff flow that usually take place simultaneously during a rainfall event. However, the interactive effect of these two processes on soil erosion has received limited attention. The objectives of this study were to better understand the mechanism of soil erosion, solute transport in runoff, and hydraulic characteristics of flow under the simultaneous influence of rainfall and shallow clear‐water flow scouring. Laboratory flume experiments with three rainfall intensities (0, 60, and 120 mm h⁻¹) and four scouring inflow rates (10, 20, 30, and 40 l min⁻¹) were conducted to evaluate their interactive effect on runoff. Results indicate that both rainfall intensity and scouring inflow rate play important roles on runoff formation, soil erosion, and solute transport in the surface runoff. A rainfall splash and water scouring interactive effect on the transport of sediment and solute in runoff were observed at the rainfall intensity of 60 mm h⁻¹ and scouring inflow rates of 20 l min⁻¹. Cumulative sediment mass loss (Ms) was found to be a linear function of cumulative runoff volume (Wr) for each treatment. Solute transport was also affected by both rainfall intensity and scouring inflow rate, and the decrease in bromide concentration in the runoff with time fitted to a power function well. Reynolds number (Re) was a key hydraulic parameter to determine erodability on loess slopes. The Darcy–Weisbach friction coefficients (f) decreased with the Reynolds numbers (Re), and the average soil and water loss rate (M_l) increased with the Reynolds numbers (Re) on loess slope for both scenarios with or without rainfall impact. Copyright © 2010 John Wiley & Sons, Ltd.     

A new baseflow separation method based on analytical solutions of the Horton infiltration capacity curve

The separation of baseflow is an important issue in hydrology. The objective of this paper is to develop a new baseflow separation method based on the Horton infiltration capacity curve. For this purpose, the mathematical expressions of three parameters for the Horton infiltration capacity curve were derived in terms of rainfall and runoff data, and the lag time of the effective rainfall in the unsaturated zone and the groundwater flow routing equation are also presented. With these equations, the baseflow hydrographs at the outlet of the basin can be separated. The flow chart of the proposed method for baseflow hydrograph separation is given. Three recent baseflow separation methods, i.e. digital filter, non‐linear reservoir and the Boussinesq equation, were chosen as parallel schemes to compare with the proposed method. Rainfall‐runoff data from four watersheds located in different climatic regions in China were selected and used as case studies. Test and application results indicate that the proposed baseflow hydrograph separation method is in accordance with the hydrological physical process. The proposed method is comparable with current available methods and reduces some of the subjective aspects for the rising limb of the baseflow hydrograph, and it is useful for unit hydrograph analysis and for the study of the rainfall‐runoff relationship. Copyright © 2006 John Wiley & Sons, Ltd.     

Dynamics of stormflow generation—A hillslope‐scale field study in east‐central Pennsylvania,USA

A 40 m × 20 m mowed, grass hillslope adjacent to a headwater stream within a 26‐ha watershed in east‐central Pennsylvania, USA, was instrumented to identify and map the extent and dynamics of surface saturation (areas with the water table at the surface) and surface runoff source areas. Rainfall, stream flow and surface runoff from the hillslope were recorded at 5‐min intervals from 11 August to 22 November 1998, and 13 April to 12 November 1999. The dynamics of the water table (0 to 45 cm depth from the soil surface) and the occurrence of surface runoff source areas across the hillslope were recorded using specially designed subsurface saturation and surface runoff sensors, respectively. Detailed data analyses for two rainfall events that occurred in August (57·7 mm in 150 min) and September (83·6 mm in 1265 min) 1999, illustrated the spatial and temporal dynamics of surface saturation and surface runoff source areas. Temporal data analyses showed the necessity to measure the hillslope dynamics at time intervals comparable to that of rainfall measurements. Both infiltration excess surface runoff (runoff caused when rainfall intensity exceeds soil infiltration capacity) and saturation excess surface runoff (runoff caused when soil moisture storage capacity is exceeded) source areas were recorded during these rainfall events. The August rainfall event was primarily an infiltration excess surface runoff event, whereas the September rainfall event produced both infiltration excess and saturation excess surface runoff. Occurrence and disappearance of infiltration excess surface runoff source areas during the rainfall events appeared scattered across the hillslope. Analysis of surface saturation and surface runoff data showed that not all surface saturation areas produced surface runoff that reached the stream. Emergence of subsurface flow to the surface during the post‐rainfall periods appeared to be a major flow process dominating the hillslope after the August rainfall event. Copyright © 2002 John Wiley & Sons, Ltd.     

Effects of rainfall intensity fluctuations on infiltration and runoff: rainfall simulation on dryland soils,Fowlers Gap,Australia

Small plots and a dripper rainfall simulator were used to explore the significance of the intensity fluctuations (‘event profile’) within simulated rainfall events on infiltration and runoff from bare, crusted dryland soils. Rainfall was applied at mean rain rates of 10 mm/h. Fourteen simulated rainfall events each involved more than 5000 changes of intensity and included multipeak events with a 25‐mm/h peak of intensity early in the event or late in the event and an event that included a temporary cessation of rain. These are all event profiles commonly seen in natural rain but rarely addressed in rainfall simulation. A rectangular event profile of constant intensity, as commonly used in rainfall simulation experiments, was also adopted for comparative purposes. Results demonstrate that event profile exerts an important effect on infiltration and runoff for these soils and rainfall event profiles. ‘Uniform’ events of unvarying intensity yielded the lowest total runoff, the lowest peak runoff rate and the lowest runoff ratio (0.13). These parameters increased for ‘early peak’ profiles (runoff ratio 0.24) and reached maxima for ‘late peak’ profiles (runoff ratio 0.50). Differences in runoff ratio and peak runoff rate between the ‘uniform’ event profile and those of varying intensity were all statistically significant at p ≤ 0.01. Compared with ‘uniform’ runs, the varying intensity runs yielded larger runoff ratios and peak runoff rates, exceeding those of the ‘uniform’ events by 85%–570%. These results suggest that for small‐plot studies of infiltration and erosion, the continued use of constant rainfall intensity simulations may be sacrificing important information and misrepresenting the mechanisms involved in runoff generation. The implications of these findings for the ecohydrology of the research site, an area of contour‐aligned banded vegetation in which runoff and runon are of critical importance, are highlighted. Copyright © 2011 John Wiley & Sons, Ltd.     

Infiltration and runoff generation processes in fire‐affected soils

Post‐wildfire runoff was investigated by combining field measurements and modelling of infiltration into fire‐affected soils to predict time‐to‐start of runoff and peak runoff rate at the plot scale (1 m²). Time series of soil‐water content, rainfall and runoff were measured on a hillslope burned by the 2010 Fourmile Canyon Fire west of Boulder, Colorado during cyclonic and convective rainstorms in the spring and summer of 2011. Some of the field measurements and measured soil physical properties were used to calibrate a one‐dimensional post‐wildfire numerical model, which was then used as a ‘virtual instrument’ to provide estimates of the saturated hydraulic conductivity and high‐resolution (1 mm) estimates of the soil‐water profile and water fluxes within the unsaturated zone. Field and model estimates of the wetting‐front depth indicated that post‐wildfire infiltration was on average confined to shallow depths less than 30 mm. Model estimates of the effective saturated hydraulic conductivity, K_s, near the soil surface ranged from 0.1 to 5.2 mm h^?1. Because of the relatively small values of K_s, the time‐to‐start of runoff (measured from the start of rainfall), t_p, was found to depend only on the initial soil‐water saturation deficit (predicted by the model) and a measured characteristic of the rainfall profile (referred to as the average rainfall acceleration, equal to the initial rate of change in rainfall intensity). An analytical model was developed from the combined results and explained 92–97% of the variance of t_p, and the numerical infiltration model explained 74–91% of the variance of the peak runoff rates. These results are from one burned site, but they strongly suggest that t_p in fire‐affected soils (which often have low values of K_s) is probably controlled more by the storm profile and the initial soil‐water saturation deficit than by soil hydraulic properties. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.     

A statistically based runoff‐yield model coupling infiltration excess and saturation excess mechanisms

A statistically based runoff‐yield model is proposed in this paper. The model considers spatial heterogeneities of rainfall, soil infiltration capacity and soil water storage capacity that are main factors controlling runoff‐yield process. It assumes that the spatial variation of rainfall intensity at each time step can be characterized by a probability density function, which is estimated by matching the hyetograph through goodness‐of‐fit measure, whereas the spatial heterogeneities of soil infiltration capacity and soil water storage capacity are described by parabola‐type functions. Surface runoff is calculated according to infiltration excess mechanism; the statistical distribution of surface runoff rate can be deduced with the joint distribution of rainfall intensity and soil infiltration rate, thus obtaining a quasi‐analytical solution for surface runoff. Based on saturation excess mechanism, the groundwater flow (flows below the ground are collectively referred to as groundwater flow) is calculated by infiltration and the probability distribution of soil water storage capacity. Consequently, the total runoff is composed of infiltration excess and saturation excess runoff components. As an example, this model is applied to flood event simulation in Dongwan catchment, a semi‐humid region and a tributary of Yellow River in China. It indicates that the proposed runoff‐yield model could achieve acceptable accuracy. Copyright © 2011 John Wiley & Sons, Ltd.     

Spatial–temporal variability and hydrologic connectivity of runoff generation areas in a North Alabama pasture—implications for phosphorus transport

This study delineated spatially and temporally variable runoff generation areas in the Sand Mountain region pasture of North Alabama under natural rainfall conditions, and demonstrated that hydrologic connectivity is important for generating hillslope response when infiltration‐excess (IE) runoff mechanism dominates. Data from six rainfall events (13·7–32·3 mm) on an intensively instrumented pasture hillslope (0·12 ha) were analysed. Analysis of data from surface runoff sensors, tipping bucket rain gauge and HS‐flume demonstrated spatial and temporal variability in runoff generation areas. Results showed that the maximum runoff generation area, which contributed to runoff at the outlet of the hillslope, varied between 67 and 100%. Furthermore, because IE was the main runoff generation mechanism on the hillslope, the data showed that as the rainfall intensity changed during a rainfall event, the runoff generation areas expanded or contracted. During rainfall events with high‐intensity short‐ to medium‐duration, 4–8% of total rainfall was converted to runoff at the outlet. Rainfall events with medium‐ to low‐intensity, medium‐duration were found less likely to generate runoff at the outlet. In situ soil hydraulic conductivity (k) was measured across the hillslope, which confirmed its effect on hydrologic connectivity of runoff generation areas. Combined surface runoff sensor and k‐interpolated data clearly showed that during a rainfall event, lower k areas generate runoff first, and then, depending on rainfall intensity, runoff at the outlet is generated by hydrologically connected areas. It was concluded that in IE‐runoff‐dominated areas, rainfall intensity and k can explain hydrologic response. The study demonstrated that only connected areas of low k values generate surface runoff during high‐intensity rainfall events. Identification of these areas would serve as an important foundation for controlling nonpoint source pollutant transport, especially phosphorus. The best management practices can be developed and implemented to reduce transport of phosphorus from these hydrologically connected areas. Copyright © 2009 John Wiley & Sons, Ltd.     

Is the connectivity function a good indicator of soil infiltrability distribution and runoff flow dimension?

Among the studies on runoff connectivity of soils with heterogeneous properties, the need to understand the relationships between soil heterogeneity and the associated runoff organization and amount is frequently mentioned. In this study, we simulate the stationary runoff–runon process on bi‐dimensional (2D) flat slopes for five infiltrability distributions, one of them correlated, as a function of rainfall intensity and flow dimension. We define flow dimension by 1 + ε, where ε is the outflow fraction transferred from one pixel to each of the two lateral downslope pixels. Our aim is to assess the effect of ε and soil heterogeneity on the connectivity function compared to the mean runoff flow rate, the wet area and the number of runoff patterns. The analysis of connectivity is carried within the percolation framework. The results show that the integral connectivity scale is more sensitive to the flow dimension and soil heterogeneity compared to the other variables. The wet area fraction does not depend on ε. Unlike previous studies, we find that increased runoff production is not necessarily related to increased connectivity. The use of the connectivity function within the percolation framework appears to be a valuable method for assessing the impact of soil heterogeneity and flow dimension on the runoff organization during a rainfall event. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of soil‐hydraulic properties and infiltration timescales in wildfire‐affected soils

We collected soil‐hydraulic property data from the literature for wildfire‐affected soils, ash, and unburned soils. These data were used to calculate metrics and timescales of hydrologic response related to infiltration and surface runoff generation. Sorptivity (S) and wetting front potential (Ψ_f) were significantly different (lower) in burned soils compared with unburned soils, whereas field‐saturated hydraulic conductivity (K_fs) was not significantly different. The magnitude and duration of the influence of capillarity during infiltration was greatly reduced in burned soils, causing faster ponding times in response to rainfall. Ash had large values of S and K_fs but moderate values of Ψ_f, compared with unburned and burned soils, indicating ash has long ponding times in response to rainfall. The ratio of S²/K_fs was nearly constant (~100 mm) for unburned soils but more variable in burned soils, suggesting that unburned soils have a balance between gravity and capillarity contributions to infiltration that may depend on soil organic matter, whereas in burned soils the gravity contribution to infiltration is greater. Changes in S and K_fs in burned soils act synergistically to reduce infiltration and accelerate and amplify surface runoff generation. Synthesis of these findings identifies three key areas for future research. First, short timescales of capillary influences on infiltration indicate the need for better measurements of infiltration at times less than 1 min to accurately characterize S in burned soils. Second, using parameter values, such as Ψ_f, from unburned areas could produce substantial errors in hydrologic modeling when used without adjustment for wildfire effects, causing parameter compensation and resulting underestimation of K_fs. Third, more thorough measurement campaigns that capture soil‐structural changes, organic matter impacts, quantitative water repellency trends, and soil‐water content along with soil‐hydraulic properties could drive the development of better techniques for numerically simulating infiltration in burned areas.     

Modeling scale-dependent runoff generation in a small semi-arid watershed accounting for rainfall intensity and water depth

Observed scale effects of runoff on hillslopes and small watersheds derive from complex interactions of time-varying rainfall rates with runoff, infiltration and macro- and microtopographic structures. A little studied aspect of scale effects is the concept of water depth-dependent infiltration. For semi-arid rangeland it has been demonstrated that mounds underneath shrubs have a high infiltrability and lower lying compacted or stony inter-shrub areas have a lower infiltrability. It is hypothesized that runoff accumulation further downslope leads to increased water depth, inundating high infiltrability areas, which increases the area-averaged infiltration rate. A model was developed that combines the concepts of water depth-dependent infiltration, partial contributing area under variable rainfall intensity, and the Green–Ampt theory for point-scale infiltration. The model was applied to rainfall simulation data and natural rainfall–runoff data from a small sub-watershed (0.4 ha) of the Walnut Gulch Experimental Watershed in the semi-arid US Southwest. Its performance to reproduce observed hydrographs was compared to that of a conventional Green–Ampt model assuming complete inundation sheet flow, with runon infiltration, which is infiltration of runoff onto pervious downstream areas. Parameters were derived from rainfall simulations and from watershed-scale calibration directly from the rainfall–runoff events. The performance of the water depth-dependent model was better than that of the conventional model on the scale of a rainfall simulator plot, but on the scale of a small watershed the performance of both model types was similar. We believe that the proposed model contributes to a less scale-dependent way of modeling runoff and erosion on the hillslope-scale.     

Runoff generation and routing on artificial slopes in a Mediterranean–continental environment: the Teruel coalfield,Spain

The aim of this study was to identify the mechanisms of runoff generation and routing and their controlling factors at the hillslope scale, on artificial slopes derived from surface coal mining reclamation in a Mediterranean–continental area. Rainfall and runoff at interrill and microcatchment scales were recorded for a year on two slopes with different substrata: topsoil cover and overburden cover. Runoff coefficient and runoff routing from interrill areas to microcatchment outlets were higher in the overburden substratum than in topsoil, and greater in the most developed rill network. Rainfall volume is the major parameter responsible for runoff response on overburden, suggesting that this substratum is very impermeable—at least during the main rainfall periods of the year (late spring and autumn) when the soil surface is sealed. In such conditions, most rainfall input is converted into runoff, regardless of its intensity. Results from artificial rainfall experiments, conducted 3 and 7 years after seeding, confirm the low infiltration capacity of overburden when sealed. The hydrological response shows great seasonal variability on the overburden slope in accordance with soil surface changes over the year. Rainfall volume and intensities (I₃₀, I₆₀) explain runoff at the interrill scale on the topsoil slope, where rainfall experiments demonstrated a typical Hortonian infiltration curve. However, no correlation was found at the microcatchment level, probably because of the loss of functionality of the only rill as ecological succession proceeded. The runoff generation mechanism on the topsoil slope is more homogeneous throughout the year. Runoff connectivity, defined as the ratio between runoff rates recorded at the rill network scale and those recorded at the interrill area scale in every rainfall event, was also greater on the rilled overburden slope, and in the most developed rill network. The dense rill networks of the overburden slope guarantee very effective runoff drainage, regardless of rainfall magnitude. Rills drain overland flow from interrill‐sealed areas, reducing the opportunity of reinfiltration in areas not affected by siltation. Runoff generation and routing on topsoil slopes are controlled by grass cover and soil moisture content, whereas on overburden slopes rill network density and soil moisture content are the main controlling factors. Copyright © 2002 John Wiley & Sons, Ltd.     

Factors influencing surface runoff generation in a Mediterranean semi-arid environment: Chicamo watershed,SE Spain

A deeper knowledge of the hydrological response of semi-arid Mediterranean watersheds would be useful in the prediction of runoff production for assessing flood risks and planning flood mitigation works. This study was conducted to identify the runoff generation mechanisms and their controlling factors at the hillslope scale in a Mediterranean semi-arid watershed. Four zero-order microcatchments were selected to measure rainfall and runoff for a three-year period. Two groups of soil were differentiated with respect to the hydrological response. The fine textured, poorly permeable soils of low organic carbon content had a greater runoff coefficient (9%) and lower runoff threshold (3·6 mm) than more permeable, coarser textured soils of medium organic carbon content (<3%, and 8 mm, respectively). The influence of rainfall characteristics on the hydrological response was different. Rain intensity was the major rainfall parameter controlling the runoff response in the microcatchments on fine textured, low infiltrability soils with a poor plant cover, while total rainfall was more closely correlated with runoff in coarser textured, highly permeable soils with a denser plant cover. It can be concluded that there are two runoff generation mechanisms: (i) an infiltration-excess overland flow in the more degraded areas with low organic carbon content (<0·5%) and low infiltrability (>5 mm h⁻¹); and (ii) a saturation-excess overland flow in the less degraded areas with a high organic carbon content (>2%), high infiltrability (>8 mm h⁻¹) and covered by a dense plant cover (>50%). © 1998 John Wiley & Sons, Ltd.     

Impacts of annual precipitation extremes on soil and nutrient losses in vineyards of NE Spain

The objective of this research was to characterise annual precipitation extremes in a Mediterranean vineyard region. The number of exceptional events (P > 95th percentile) and annual extreme events (P > 99th percentile), as well as their strength, erosive character and return period were analysed for 2000–2004. The erosive character was evaluated according to the R‐factor (kinetic energy × maximum intensity in 30‐min periods). Soil and nutrient losses caused by these events were evaluated by combining field sampling and a hydrological model to estimate total runoff in a vineyard plot. The results show a clear increase in the number of very wet days and extreme events (P > 95th percentile), which represented up to 88% of annual rainfall. The severity of the extreme events (TS = precipitation event P > 99th percentile) reached values higher than 50 mm almost every year. These values were far exceeded in 2000, when one extraordinary event recorded 50% of the annual rainfall, with TS of 189 mm, about 80% of total rainfall being lost as runoff. Annual erosivity was driven not only by extreme events, but also by short events of less depth but high intensity. During some of the years analysed, rainfall erosivity was two or three times the average in the area. Most soil and nutrient losses occurred in a small number of events: one or two events every year were responsible for more than 75% of the annual soil and nutrient losses on average. Antecedent soil moisture conditions, runoff rates, and events with a return period higher than two years were responsible for the higher erosion rates. Apart from an exceptional event recorded in 2000, which produced more than 200 Mg ha^?1 soil losses, annual soil losses up to 25 Mg ha^?1 were recorded, which are much higher than the soil loss tolerance. Copyright © 2008 John Wiley & Sons, Ltd.     

Stochastic–conceptual analysis of near‐surface hydrological response

The stochastic–conceptual rainfall–runoff simulator (SCRRS) developed by R. A. Freeze in 1980 was used in this study to demonstrate quantitatively the interplay of the factors that control the occurrence of overland flow by the Horton and Dunne mechanisms. The simulation domain and input data for the SCRRS simulations reported here were abstracted from the R‐5 catchment (Chickasha, OK) data sets. The results illustrate that the identification of a dominant hydrological response process may not be as simple as a singular Horton or Dunne characterization. The SCRRS simulations show that the Horton and Dunne processes can (i) occur simultaneously at different locations during a given rainfall event, (ii) change from one process to the other with time depending on the characteristics of the rainfall event, and (iii) be strongly dependent on the initial conditions. Copyright © 2001 John Wiley & Sons, Ltd.     

Runoff initiation in a preserved semiarid Caatinga small watershed,Northeastern Brazil

This study analyses some hydrological driving forces and their interrelation with surface‐flow initiation in a semiarid Caatinga basin (12 km²), Northeastern Brazil. During the analysis period (2005 – 2014), 118 events with precipitation higher than 10 mm were monitored, providing 45 events with runoff, 25 with negligible runoff and 49 without runoff. To verify the dominant processes, 179 on‐site measurements of saturated hydraulic conductivity (Ksat) were conducted. The results showed that annual runoff coefficient lay below 0.5% and discharge at the outlet has only occurred four days per annum on average, providing an insight to the surface‐water scarcity of the Caatinga biome. The most relevant variables to explain runoff initiation were total precipitation and maximum 60‐min rainfall intensity (I₆₀). Runoff always occurred when rainfall surpassed 31 mm, but it never occurred for rainfall below 14 mm or for I₆₀ below 12 mm h^?1. The fact that the duration of the critical intensity is similar to the basin concentration time (65 min) and that the infiltration threshold value approaches the river‐bank saturated hydraulic conductivity support the assumption that Hortonian runoff prevails. However, none of the analysed variables (total or precedent precipitation, soil moisture content, rainfall intensities or rainfall duration) has been able to explain the runoff initiation in all monitored events: the best criteria, e.g. failed to explain 27% of the events. It is possible that surface‐flow initiation in the Caatinga biome is strongly influenced by the root‐system dynamics, which changes macro‐porosity status and, therefore, initial abstraction. Copyright © 2016 John Wiley & Sons, Ltd.     

Using a transient infiltrometric technique for intensively sampling field‐saturated hydraulic conductivity of a clay soil in two runoff plots

The point measurement of soil properties allows to explain and simulate plot scale hydrological processes. An intensive sampling was carried out at the surface of an unsaturated clay soil to measure, on two adjacent plots of 4 × 11 m² and two different dates (May 2007 and February–March 2008), dry soil bulk density, ρ_b, and antecedent soil water content, θ_i, at 88 points. Field‐saturated soil hydraulic conductivity, K_fs, was also measured at 176 points by the transient Simplified Falling Head technique to determine the soil water permeability characteristics at the beginning of a possible rainfall event yielding measurable runoff. The ρ_b values did not differ significantly between the two dates, but wetter soil conditions (by 31%) and lower conductivities (1.95 times) were detected on the second date as compared with the first one. Significantly higher (by a factor of 1.8) K_fs values were obtained with the 0.30‐m‐diameter ring compared with the 0.15‐m‐diameter ring. A high K_fs (> 100 mm h^?1) was generally obtained for low θ_i values (< 0.3 m³m^?3), whereas a high θ_i yielded an increased percentage of low K_fs data (1–100 mm h^?1). The median of K_fs for each plot/sampling date combination was not lower than 600 mm h^?1, and rainfall intensities rarely exceeded 100 mm h^?1 at the site. The occurrence of runoff at the base of the plot needs a substantial reduction of the surface soil permeability characteristics during the event, probably promoted by a higher water content than the one of this investigation (saturation degree = 0.44–0.62) and some soil compaction due to rainfall impact. An intensive soil sampling reduces the risk of an erroneous interpretation of hydrological processes. In an unstable clay soil, changes in K_fs during the event seem to have a noticeable effect on runoff generation, and they should be considered for modeling hydrological processes. Copyright © 2012 John Wiley & Sons, Ltd.     

Impact of rainfall movement on soil crust development

The impact of rainfall event movement on soil crust development was investigated via laboratory experiments and physics-based hydrological-response simulation.Runoff and soil water content data were analyzed in order to study different crustal development periods under a variety of precipitation conditions.The results showed that the formation of crust significantly changed soil saturated hydraulic conductivity(K_s) and runoff,while a steady state,which could be broken by an extended period of raindrop impact,was found to exist for both the crust and,subsequently,runoff characteristics.The decrease in K_S was as high as 86%for downstream-moving events,and 72%for upstream-moving events,illustrating that the direction of rainfall movement has a more significant impact on crust formation than rainfall intensity and duration.As downstream-moving rainfall events may have a greater effect than those moving upstream,the development of a depositional crust before raindrop impact may play an important role in determining the final K_S value.     

Occurrence of water ponding on soil surfaces depending on infiltration rates on Mongolian rangeland

The occurrence of water ponding on soil surfaces during and after heavy rainfall produces surface run‐off or surface water accumulation in low‐lying areas, which might reduce the water supply to soils and result in a reduction of the soil water that plants can use, especially in arid climates. On Mongolian rangeland, we observed ponded water on the surface of a specific soil condition subjected to a heavy rainfall of 30 mm/hr. By contrast, ponded water was not observed for the same type of soil where livestock grazing had been removed for 6–8 years via a fence or for nearby soil containing less clay. We measured the infiltration rate (the saturated hydraulic conductivity of the surface soil, K_s) of the three sites by applying ponded water on the soil surface (an intake rate test). The results showed that K_s in the rangeland was lower than the rainfall intensity in the site where water ponded on the soil surface; however, K_s of the soil inside of the fence has recovered to 3 times that of the soil outside of the fence to exceed the rainfall intensity. Heavy rainfall that exceeds the infiltration rate occurs several times a year at the livestock grazing site where we observed ponded water. Slight water repellency of the soil reduces rain infiltration to increase the possibility of surface ponding for the soil.