The Shaking Table Test on the Performance of Cement-mixed Piles in Liquefiable Railway Foundations

Cement-mixed piles, as countermeasure against liquefaction of silt and sand ground, can improve the shear strength and bearing capacity of foundation soil, meaning cement-mixed piles are capable of resisting displacement when an earthquake happens. However, investigations of cement-mixed piles by experimental methods such as the shaking table test is few and far between. It is especially true for the seismic performance of cement-mixed piles in liquefiable railway foundations in high seismic intensity regions. To this end, a cross-section of the Yuxi-Mengzi railway was selected as the prototype and studied by the shaking table test in this study. The results showed that composite foundation of cement-mixed piles was not liquefied when the seismic acceleration was lower than 0.30g. In the process of acceleration increasing from 0.30g at 2Hz to 0.60g at 3Hz, the upper middle silt outside slope toe was partly liquefied. The foundation soil under the shoulders and center of subgrade was far from the initial liquefaction criterion during the test. Cement-mixed piles can effectively reduce the embankment settlement and differential settlement. It can be concluded that, the design of cement-mixed piles can ensure the seismic performance of the subgrade, and satisfy the seismic design requirements of the Yuxi-Mengzi railway in areas of VⅢ degrees seismic fortification intensity.     

Flow and deformation failure of sandy slopes

The effects of earthquake induced pore pressure on seismic and post seismic stability conditions of cohesionless slopes are investigated with reference to the infinite slope scheme. In cohesionless slopes the shear strength reduction caused by pore pressure build-up may lead the slope to a deformation failure or to a flow failure if liquefaction conditions are approached. Two critical values of the seismic induced pore pressure ratio are introduced to evaluate the effect of shear strength reduction on the slope failure mechanism. The results are given in the form of stability charts and a procedure for the evaluation of the seismic stability condition is described. The procedure gives useful information about the failure mechanism that slopes may exhibit and the displacement analysis which should be carried out.     

Settlements of saturated clean sand deposits in shaking table tests

Shaking table tests were conducted on saturated clean Vietnam sand in the large biaxial laminar shear box (1880 mm×1880 mm×1520 mm) at the National Center for Research on Earthquake Engineering (NCREE), Taiwan. The settlement of sand specimens was measured and evaluated during and after each shaking test. Without liquefaction, the settlement of sand caused by shaking is very small. Significant volume changes occur only when there is liquefaction of sand. The volumetric strain of liquefied sand was calculated according to the measured settlement and the thickness of liquefied sand in the specimen. Relations between volumetric strain after liquefaction and the relative density of saturated clean sand were developed for various shaking durations and earthquake magnitudes. They are not affected by the shaking amplitude, frequency, and direction (one- or multidirectional shaking).     

轮胎加筋砂垫层抗液化性能振动台试验研究

将废弃橡胶轮胎内填充散体材料形成加筋土结构,已被应用于地基、挡土墙和边坡加固等工程,表现出较好的减震隔振效果,而轮胎加筋土的抗液化性能尚缺乏研究。开展3组小型振动台试验,通过改变轮胎垫层的排水条件,验证轮胎加筋砂垫层的抗液化效果。结果表明:轮胎加筋砂垫层具有良好的抗液化效果,与刚性垫层相比,超静孔压比峰值差值范围在0.01~0.19,残余超静孔压比差值范围在0.08~0.16,轮胎加筋砂垫层提供的排水通道具有抑制超静孔隙水压力发展和加速超静孔隙水消散的作用,孔隙水会沿着轮胎与下部土体的界面以及胎间的排水通道排出;采用量测侧向动土压力的方法,定义土体液化程度量化指标,进一步验证轮胎加筋砂垫层抗液化效果;振动过程中轮胎加筋垫层表面沉降范围为11.3~15.7 mm,表现出较好的变形协调性能。     

Centrifuge modeling of the seismic responses of sand deposits with an intra-silt layer

Three dynamic centrifuge model tests were conducted at an acceleration of 80g to simulate the seismic responses of level sand deposits: an intra-silt layer was embedded in two of these sand deposits at different depths. The effects of a low-permeability intra-silt layer on the build-up and dissipation of excess pore-water pressure, surface settlement, and the related liquefaction mechanism were investigated. An intra-silt layer modifies the seismic response of the sand deposit, reduces the extent of liquefaction, and thus decreases surface settlement. The depth of the intra-silt layer is one of the factors influencing the seismic responses of the sand deposits. The magnitude of the surface settlement is proportional to the degree of liquefaction in the sand deposit. The high positive hydraulic gradients appearing in both the intra-silt layer and in the sand deposit lying on the intra-silt layer can break a thinner or weaker top layer and result in sand boiling. Our visual animation of the ratio of the excess pore-water pressure and the lateral displacement revealed that the liquefaction front travels upward during shaking and the solidification front travels upward after shaking.     

砂土自由场地震响应的离心机试验研究

离心机模型试验是研究岩土地震工程问题的有效手段。本文使用层状剪切箱,通过干落法制备了均匀的砂土模型,进行了离心机振动试验;观测了振动过程中孔隙水压力的发展,土体的加速度响应、侧向变形以及竖向沉降。结果表明,土体的运动和变形与孔隙水压力的发展密切相关,但离心机中的试验现象和现场观测的现象存在显著区别。研究结果增强了对振动过程中土-水之间相互作用机理的理解,同时为自由场地震响应分析方法的验证提供了基础数据。     

Shaking table test on small‐scale retrofitted model of Sefid‐rud concrete buttress dam

Sefid‐rud concrete buttress dam with a height of 106 m was damaged during the devastating 1990 Manjil earthquake. The dam was repaired and strengthened using epoxy grouting of cracks and the installation of post‐tensioned anchors. In a previous study, nonlinear seismic response of the highest monolith with empty reservoir was investigated experimentally through model testing. A geometric‐scaled model of 1:30 was tested on a shaking table to study dynamic cracking of the model. As a result of the similarity between model and prototype cracking pattern, the model was retrofitted according to prototype retrofitting plan after the Manjil earthquake and re‐tested on shaking table to estimate the current safety of the prototype. Experimental test results showed that the post‐tensioning resulted in a significant decrease in dynamic responses in terms of crest displacement and measured strains of the retrofitted model in comparison with its corresponding responses at the first test. No cracking was observed in the retrofitted model when the base motion peak acceleration exceeded a value that was 22% higher than the one caused cracking in the first model. This can be interpreted as the efficiency of prototype post‐tensioning system in evaluating the seismic safety of Sefid‐rud dam. Copyright © 2009 John Wiley & Sons, Ltd.     

国内外液化砂砾土土性对比分析

砂土液化问题的研究特别是砂土液化的判别目前已经取得了较大的进展,并在国内外现行的规范中充分反映,而砂砾土由于颗粒大、透水性好,普遍认为地震时孔压不至于上升至液化的程度,往往将其划分为非液化土类。通过调查汶川地震砂砾土液化情况以及勘察试验获取其土性资料,对比分析了国内外液化砂砾土的地质背景及土性特征。主要认识为：①以往国内外砂砾土液化实例虽然有限,但已经表明松散-稍密的砂砾土在一定的地震强度下仍有可能发生液化,而2008年汶川地震中的大量砂砾土液化的事实,说明笼统地将砂砾土划归为非液化土类的做法有误;②汶川地震液化砂砾土的颗粒级配范围涵盖了国内外其他地震的颗粒级配,研究汶川地震的砂砾土液化问题具有代表性和普遍性,以此建立的砂砾土液化评价方法在国际上应具有通用性。     

基于振动台试验的黄土塬边斜坡变形失稳模式研究

以甘肃省平凉市的典型黄土塬斜坡为原型,开展含裂隙黄土塬边斜坡与不含裂隙黄土塬边斜坡的振动台对比模型试验,研究不同强度地震作用下两种黄土斜坡的变形失稳特征。结果表明:两种不同结构的斜坡在不同强度地震作用下的破坏特征显著不同,裂隙的存在降低了含裂隙斜坡的抗震稳定性。随着输入地震波幅值的增加,含裂隙斜坡的变形破坏过程为:坡顶裂隙处先后发生裂隙前缘崩塌、坡面溜土、临空面方向大位移、坡面中部和坡脚鼓胀、剪切滑移、发生多级滑动,同时坡体后缘产生新的拉张裂隙;无裂隙斜坡的破坏过程为:坡顶形成拉张裂缝、坡面溜土、坡脚鼓胀、发生单级滑动。两种结构边坡的变形破裂包括倾倒—拉裂与剪切—滑移两种模式,斜坡的变形演化是两种模式相互作用的结果。     

Investigation of liquefaction and pore water pressure development in layered sands

This paper presents the results of shaking table model tests which were carried out to investigate the pore water pressure generation and related liquefaction mechanism in layered sand deposits. The experiments were performed on uniform sand columns, silt interlayered sand columns and two layered sand columns deposited at various relative densities and subjected to different input excitations. During the experiments excess pore water pressures were measured by pore pressure transducers installed at three different depths and, surface settlements and thickness of water film developed under less permeable inclusions were measured by a digital camera. The experimental results are discussed and compared to demonstrate the effects of relative density, input acceleration and presence of a silt seam on the generation of excess pore water pressure in sand deposits subjected to dynamic loading. The results showed that the presence of a less permeable silt interlayer within the sand deposit and existence of a loose sand layer underlying dense sand deposits can have significant effect on the pore water pressure generation mechanism.     

Centrifuge model tests on liquefaction-induced settlement and pore water migration in non-homogeneous soil deposits

This paper presents the results of dynamic centrifuge model tests conducted to investigate the liquefaction mechanism in non-homogeneous soil deposits. Four types of model tests were conducted: one model test involved a uniform soil deposit; one involved continuous layered soil deposit; and two involved discontinuous layered soil deposits. Non-homogeneity in the tests was incorporated by including periodically distributed discontinuous silty sand patches. It was found that more excess pore water pressure (EPWP) remains for a longer period of time in the discontinuous region in non-homogeneous soil deposits compared with the continuous layered and uniform soil deposits. The generation of pore water pressure ceases the supply of a new mass of water after seismic excitation; therefore the dissipation of EPWP becomes the dominant factor for settlement after seismic excitation. The rapid dissipation of EPWP through the discontinuous part in the non-homogeneous soil deposits manifests as a larger settlement in the discontinuous part, causing non-uniform settlements.     

Pile response in submerged lateral spreads: Common pitfalls of numerical and physical modeling techniques

A three dimensional dynamic numerical methodology is developed and used to back-analyze experimental data on the seismic response of single piles in laterally spreading slopes. The aim of the paper is not to seek successful a-priori (Type A) predictions, but to explore the potential of currently available numerical techniques, and also to get feedback on modeling issues and assumptions which are not yet resolved in the international literature. It is illustrated that accurate simulation of the physical pile–soil interaction mechanisms is not a routine task, as it requires the incorporation of advanced numerical features, such as an effective stress constitutive soil model that can capture cyclic response and shear-induced dilation, interface elements to simulate the flow of liquefied ground around the pile and proper calibration of soil permeability to model excess pore pressure dissipation during shaking. In addition, the “conventional tied node” formulation, commonly used to simulate lateral boundary conditions during shaking, has to be modified in order to take into account the effects of the hydrostatic pore pressure surplus that is created at the down slope free field boundary of submerged slopes. A comparative analysis with the two different lateral boundary formulations reveals that “conventional tied nodes”, which also reflect the kinematic conditions imposed by laminar box containers in centrifuge and shaking table experiments, may underestimate seismic demands along the upper part of the pile foundation.     

Soil–pile–structure interaction under SH wave excitation

A continuum model for the interaction analysis of a fully coupled soil–pile–structure system under seismic excitation is presented in this paper. Only horizontal shaking induced by harmonic SH waves is considered so that the soil–pile–structure system is under anti‐plane deformation. The soil mass, pile and superstructure were all considered as elastic with hysteretic damping, while geometrically both pile and structures were simplified as a beam model. Buildings of various heights in Hong Kong designed to resist wind load were analysed using the present model. It was discovered that the acceleration of the piled‐structures at ground level can, in general, be larger than that of a free‐field shaking of the soil site, depending on the excitation frequency. For typical piled‐structures in Hong Kong, the amplification factor of shaking at the ground level does not show simple trends with the number of storeys of the superstructure, the thickness and the stiffness of soil, and the stiffness of the superstructure if number of storeys is fixed. The effect of pile stiffness on the amplification factor of shaking is, however, insignificant. Thus, simply increasing the pile size or the superstructure stiffness does not necessarily improve the seismic resistance of the soil–pile–structure system; on the contrary, it may lead to excessive amplification of shaking for the whole system. Copyright © 2003 John Wiley & Sons, Ltd.     

Evaluation of seismic displacements of quay walls

A new simplified dynamic analysis method is proposed to predict the seismic sliding displacement of quay walls by considering the variation of wall thrust, which is influenced by the excess pore pressure developed in backfill during earthquakes. The method uses the Newmark sliding block concept and the variable yield acceleration, which varies according to the wall thrust, to calculate the quay wall displacement.A series of 1 g shaking table tests were executed to verify the applicability of the proposed method, and a parametric study was performed. The shaking table tests verified that the proposed method properly predicts the wall displacement, and the parametric study showed that the evaluation of a realistic wall displacement is as important as the analysis of liquefaction potential for judging the stability of quay walls.     

门源M6.9地震诱发地质灾害特征研究

2022年1月8日发生的门源M6.9地震诱发了崩塌、滑坡、砂土液化、地裂缝等多种同震地质灾害。通过对门源M6.9地震地质灾害进行现场调查,得出了地质灾害的分布特征和各类型地质灾害的主要特点,分析了地震地质灾害不发育的原因,并对地震地质灾害的长期效应进行了分析预测。研究结果表明：门源地震诱发地质灾害主要分布在震中附近;崩塌、落石总体规模较小,滑坡多为岩质滑坡,且以冰碛物和表层岩土体的溜滑为主。受表层土体冻结和孔隙水压力消散的影响,饱和砂土液化沿较窄的地裂缝呈串珠状分布,喷出物多为粉细砂。地震形成了4条左旋左阶斜列的地表破裂带,并在极震区内形成了大量的地裂缝。断层破碎带对地震动的阻隔作用、覆盖层薄、地表土冻结可能是造成本次地震地质灾害总体不发育的主要原因;地震产生的大量地裂缝导致斜坡和堆积体的稳定性减弱,在耦合集中降雨、冻融作用等因素后可能诱发滑坡灾害,松散堆积于沟床处的崩滑物作为物源,可能会增加地震影响区泥石流灾害的风险。     

Shake table test of soil-pile groups-bridge structure interaction in liquefiable ground

<正>This paper describes a shake table test study on the seismic response of low-cap pile groups and a bridge structure in liquefiable ground.The soil profile,contained in a large-scale laminar shear box,consisted of a horizontally saturated sand layer overlaid with a silty clay layer,with the simulated low-cap pile groups embedded.The container was excited in three E1 Centra earthquake events of different levels.Test results indicate that excessive pore pressure(EPP) during slight shaking only slightly accumulated,and the accumulation mainly occurred during strong shaking.The EPP was gradually enhanced as the amplitude and duration of the input acceleration increased.The acceleration response of the sand was remarkably influenced by soil liquefaction.As soil liquefaction occurred,the peak sand displacement gradually lagged behind the input acceleration;meanwhile,the sand displacement exhibited an increasing effect on the bending moment of the pile,and acceleration responses of the pile and the sand layer gradually changed from decreasing to increasing in the vertical direction from the bottom to the top.A jump variation of the bending moment on the pile was observed near the soil interface in all three input earthquake events.It is thought that the shake table tests could provide the groundwork for further seismic performance studies of low-cap pile groups used in bridges located on liquefiable groun.     

下蜀土边坡地震稳定性的大型振动台试验研究（Ⅱ）——试验结果及分析

选用天然下蜀土,设计并完成了一几何相似常数为20、坡高为0.5 m、坡角为45°的模型边坡1 g大型振动台试验,通过对模型边坡动力特性、动力反应及宏观变形等三方面的研究,揭示了下蜀土边坡的地震反应机理。试验结果表明,下蜀土边坡有着稳定的一、二阶自振频率和阻尼比,随着地震动加载幅值（PGA）逐渐增大,其一阶自振频率逐渐减小,一阶阻尼比逐渐增大;坡高范围内,PGA放大系数均大于1,且自下而上逐渐增大,并在坡肩处达到最大,其在坡脚处的值小于水平方向其他位置处的值,输入El Centro波（经时间相似常数4.47压缩）时的值分别大于输入El Centro原波和Kobe波（经时间相似常数4.47压缩）时的值;随着输入PGA的增大,土体非线性特征逐渐增强,边坡也逐渐趋于失稳破坏状态;震后模型边坡坡脚、坡顶等部位出现了不同程度的裂缝,说明边坡中出现了通过坡脚的（潜在）滑动面。     

Site classification using equivalent soil profiles for building-liquefaction interaction

The seismic behaviour of a building on a liquefiable deposit is a complex interaction which involves quantifying both shaking induced damage and permanent ground deformation-related damage. In this paper the key parameters that influence both surface shaking and foundation settlements have been identified as the depth, thickness and liquefaction resistance of an equivalent liquefiable layer. These parameters can be used to develop an ‘equivalent soil profile’ that is analogous to the equivalent single degree-of-freedom that reduces the complexity of the dynamic response of a building into comparable and easily understood quantities. The equivalent soil profile is quantified independent of the seismic hazard, making it compatible with performance based design and assessment frameworks such that the building and soil profile can be directly assessed at different levels of seismic hazard. Several numerical studies are presented that demonstrate the influence of these key parameters on the ground surface shaking and foundation settlement. A set of criteria are proposed for classifying soil profiles into 22 different soil classes for regional loss assessment. An algorithm was developed for automatically fitting the equivalent soil profile to a cone penetration test trace and issues with the fitting are discussed. Field reconnaissance was undertaken to collect additional data to support existing datasets on the performance of buildings in Adapazari, during the 1999 Kocaeli, Turkey, earthquake (Mw = 7.4). The field case history data was used to investigate the correlation between the depth, thickness and liquefaction resistance of an equivalent liquefiable layer, on the extent of foundation permanent deformation. The case history data showed that in general a shallow, thick and weak liquefiable layer near the surface results in significant settlement but a lack of data for buildings on non-liquefiable deposits and the additional complexities involved with real buildings and soil deposits, meant that the trends observed in the idealised numerical models could not identified in the field case history data set.

     

液化场地桩-土-桥梁结构动力相互作用振动台试验研究进展

本文在全面归纳与总结液化场地桩－土－桥梁结构动力相互作用振动台试验及与之相关领域的国内外研究进展基础上，直接针对我国桥梁工程中的主要震害问题，提出在我国开展液化场地桩－土－桥梁结构动力相互作用振动台试验研究的必要性，并阐述作者对液化场地桩－土－张桥梁结构动力相互作用振动台试验中若干问题的认识。     

下蜀土边坡地震稳定性的大型振动台试验研究（Ⅰ）——模型试验设计

为研究下蜀土边坡的地震稳定性,选用天然下蜀土,按照Meymand的相似法则,对一坡高为0.5m、宽度为1.05m、坡角为45°的模型边坡进行了几何相似常数为20的1g大型振动台模型试验详细设计。首先,运用数值模拟的方法确定了模型边坡尺寸适当的边界范围,模型边坡地基厚度、坡脚前缘和坡肩后缘长度均取为0.5m;其次,按照确定的模型几何尺寸设计了符合试验要求的模型箱,其内壁净尺寸（长×宽×高）为1500mm×1050mm×1100mm,属刚性模型箱,且不会与模型边坡发生共振;最后,制定了包括加速度和位移在内的数据量测策略,运用拟静力法求得下蜀土边坡平均屈服加速度为0.561g,综合确定了地震动峰值（PGA）按0.1g、0.3g、0.6g和0.9g的顺序逐级加载的原则,并制定了详细的试验步骤,从而可保障试验得到可靠的结果。