型钢混凝土组合结构在不同抗震区抗震性能初步研究及其结构位移特征的初步探讨

对型钢混凝土梁柱框架结构、型钢混凝土柱-钢筋混凝土梁框架结构、纯钢筋混凝土框架结构进行分析,讨论三者在在不同的地震作用下的层间位移角、有害层间位移角、变形特征曲线上的区别。研究表明:型钢混凝土框架结构呈现剪切型的变形特征,薄弱层出现在首层及二层,大震最大层间位移角可取小震时对应数值的6.5倍进行估算,型钢混凝土框架结构更适用于8度半以上抗震设防烈度地区。     

地震作用下钢筋混凝土柱变形与损伤研究

为量化地震作用下钢筋混凝土（RC）柱损伤情况和变形,并将不同地震破坏状态下RC柱损伤和变形进行分析。从太平洋地震工程研究中心（PEER）数据库中收集91组RC柱抗震试验数据,选取4种广泛应用的构件损伤模型进行计算,将损伤发展曲线与层间位移角发展曲线进行对比分析。对RC柱损伤指标限值进行归一化处理,统计分析后得到不同破坏等级下的位移角限值,并给出了RC柱各破坏等级下的位移角限值与损伤指标限值对应关系。研究结果表明,牛荻涛损伤模型可更准确地评价地震作用下结构构件损伤程度,且与层间位移角发展曲线均呈近似线性增长趋势;不同破坏等级下的位移角限值验算保证率均＞80%,表明本文提出的位移角限值具有一定合理性。     

框架结构性能设计中钢筋混凝土变梁中节点性能指标量化研究

通过分析结构及构件变形与损伤的关系,选取层间位移角作为钢筋混凝土变梁中节点基于性能的抗震设计指标.根据钢筋混凝土结构破坏的特点和框架结构基于性能抗震设计的需要,将钢筋混凝土框架结构性能水平划分为正常使用、暂时使用、修复后使用、生命安全和防止倒塌5个层次.在8个钢筋混凝土变梁中节点伪静力试验研究的基础上,根据节点试件的破坏过程、骨架曲线以及结构性能曲线将钢筋混凝土变梁中节点的性能水平划分为“五档”,建议了不同性能水平下钢筋混凝土变梁中节点的变形和相关参数的量化标准,重点以层间位移角为性能指标量化参数,提出了节点基于性能的“五水平”参数量化指标,并结合我国现行规范给出了“三水准”设防目标下的参数量化指标.     

RC梁与柱在不同地震作用下的变形限值分析

分析钢筋混凝土(RC)梁与柱基于不同地震作用下的变形限值,对钢筋混凝土梁与柱进行低周往复循环加载拟静力试验。然后对试验进行仿真模拟,将试验结果与仿真模拟结果进行对比分析,发现二者结果相近,从而验证仿真模拟的可行性。在构件的荷载-位移曲线上获取屈服点、峰值点和极限点,分别计算这3个状态点对应的侧向位移值与构件计算长度的比值,则可得出构件在小震、中震和大震时对应的位移角值。改变梁、柱构件的剪跨比、配筋形式以及柱构件的轴压比等,来得到更多构件的荷载-位移曲线,将所有结果进行统计分析,得到钢筋混凝土构件在不同地震作用下的位移角限值。     

RC框架结构薄弱层的层间位移可靠度水平考察

讨论了钢筋混凝土框架结构层间极限变形角的近似概率特性,考察了大震作用下20余幢钢筋混凝土框架结构薄弱层的层间位移可靠度水平,从而为直接基于位移可靠度的抗震设计中层间目标位移可靠度的确定提供了一定依据。     

弹塑性位移谱法的振动台模型试验验证

弹塑性位移谱法求解结构在指定强度地面运动作用下的位移需求是一种简便合理的方法。本文将弹塑性位移谱法就具体地震波计算的楼层位移需求、层间位移角需求与一比例为1／10的12层钢筋混凝土模型框架振动台试验结果作了比较。设计的12层钢筋混凝土模型框架结构在振动台上经历了7种强度等级地震波的作用,输入峰值加速度依次为：0．090g、0．258g、0．388g、0．517g、0．646g、0．775g和0．904g。求出了弹塑性位移谱法计算的楼层位移和层问位移角需求与振动台试验结果的比值,研究了二者比值的均值及方差沿楼层的分布情况。结果表明：弹塑性位移谱法的计算结果与振动台得到的位移需求值吻合较好,在基于性能的抗震设计中具有较好的应用前景。     

考虑结构底部受剪的建筑层间位移调控及抗震性能分析

为了减少地震对建筑结构层间位移的影响,在考虑结构底部受剪的建筑中,针对层间位移调控与抗震性能的关系展开分析研究。设计建筑层间位移计算方法,计算梁、柱和节点受剪后的侧移,并依据计算结果,设置建筑层间位移限值约束条件,采用降低框架的梁距与柱距、平面结构与立体结构间的转换、弯-剪双重体系等方式,调控建筑层间位移。以某实际工程为例进行抗震性能测试验证,结果表明：所使用的层间位移计算公式的误差小于3.5%;在Kobe波与El-Centro波下的层间位移范围分别为0.43～0.82 mm和0.40～0.42 mm;经调控后,层间位移保持在0.4～1.1 mm之间,能够提升建筑的抗震性能。     

基于概率和位移的框支剪力墙结构抗震性能评估方法

本文严格按照中国规范设计出典型的带转换层部分框支剪力墙钢筋混凝土结构,通过弹塑性分析程序IDARC2D对该结构进行多个地震动作用下的大震弹塑性时程分析,得到结构及各个构件的反应量的统计特征,再参照美国基于性能抗震设计规范ASCE-41-06的结构与构件变形限值作为性能指标,计算出结构和各个构件的可靠度和可靠指标,作为评价结构抗震性能的标准,总结归纳出基于概率和位移的抗震设计方法的思路.最后运用该方法,对7、8度烈度区的框支剪力墙结构进行可靠性分析,通过对比分析,研究考虑内力增强措施、层间位移角控制条件、竖向构件轴压比限制条件、层刚比控制准则和竖向构件最小配筋率等因素对不同抗震烈度区的框支剪力墙结构的可靠性的影响,从而评价中国规范抗震措施和构造措施的有效性.     

梁铰型屈服RC框架结构地震弹塑性位移增大系数研究

本文通过弹性和弹塑性时程分析,研究了水平地震作用下梁铰型屈服RC框架模型结构的楼层屈服剪力系数、基本自振周期、楼层数3个因素对弹塑性位移增大系数的影响,通过非线性回归分析给出了弹塑性层间位移增大系数经验公式;通过分析滞回耗能沿楼层高度的分布,初步确定了梁铰型屈服RC框架结构的薄弱楼层位置;基于结构损伤分析,讨论了抗震规范中RC框架结构弹塑性层间位移角限值的水准。     

钢筋混凝土框架中震可修标准及简化抗震设计方法

本文对国际上主要建筑抗震设计规范中钢筋混凝土框架可修水准的层间位移角限值进行了比较,讨论了国内的一些相关研究结果,结合中国抗震规范确定钢筋混凝土框架中震可修层间位移角限值和屋顶侧移率限值分别为1/150和1/200。采用安全系数的抗震设计表达、论述了对应于结构层间位移角基于承载力的简化抗震设计方法。最后用实例按反应谱分析和弹性时程分析验证了钢筋混凝土框架中震可修层间位移角限值的有效控制作用,初步确定了简化抗震设计方法中梁柱构件的抗震安全系数并分析了提高目前结构抗震安全度的措施。     

钢框架结构直接基于位移的抗震设计方法研究

将钢框架结构按其性能划分为使用良好、人身安全、防止倒塌三个水平,并用层间侧移角予以量化采用钢框架的最大层侧移模式来确定其目标侧移曲线在等效线性化的前提下,由等效位移用弹性位移反应谱求出等效周期,然后对构件进行刚度设计和承载力设计用静力弹塑性分析方法对结构进行分析,校核其实际侧移曲线与满足性能目标的侧移曲线是否一致.采用...     

Limitations on linear elastic procedures in performance assessment of regular frames

Linear elastic analysis procedures are employed exclusively in the traditional seismic design of new structures and widely employed in the seismic assessment of existing structures. It is also a convenient tool for the initial checking of deformations in displacement‐based design. The limitations that should be imposed on linear elastic procedures have been evaluated in this study by comparing the deformation‐based response quantities obtained from response spectrum analysis with those from the nonlinear time history analysis. Both procedures were applied to different design variants of 5, 8, and 12 story moment frames, subjected to 20 strong motion components exhibiting a variety of intensities. Member plastic rotations and interstory drift ratios were employed as the basic response parameter in performance assessment. It has been found that average column demand to capacity ratio (DCR) (the ratio of flexural demand from linear elastic analysis to flexural capacity) and average beam DCR at the critical story are the most effective parameters in determining the validity range of linear elastic procedures in regular moment frames. Limiting values for these response parameters are proposed. Furthermore, amplification factors for member rotation demands predicted by the linear procedures are suggested for moment frames when these limiting values are exceeded. These factors ensure that the amplified linear elastic rotations are not smaller than 84 percentile (mean – 1sigma) of the rotations obtained from nonlinear time history analysis. Copyright © 2015 John Wiley & Sons, Ltd.     

施工缝对框架结构抗震性能影响的数值分析

为研究施工缝对框架结构抗震性能的影响,利用提出的施工缝模型,基于OPENSEES平台建模进行静力非线性分析和非线性动力时程分析。通过对比整浇框架与带缝框架的顶点最大位移、层间位移角、塑性铰出现和分布规律等明确施工缝对框架结构的抗震性能的影响程度。结果表明,施工缝使框架结构的变形和层间位移角显著增大,并且使8、9度区框架结构的层间位移角分布发生改变;施工缝使柱端更易出现塑性铰,更易发生"强梁弱柱"的破坏模式;在高烈度区,施工缝的影响比较显著,如果忽略其影响,将会高估框架结构的抗震性能。     

Influence of gusset plate connections and braces on the seismic performance of X‐braced frames

Braced frames are one of the most economical and efficient seismic resisting systems yet few full‐scale tests exist. A recent research project, funded by the National Science Foundation (NSF), seeks to fill this gap by developing high‐resolution data of improved seismic resisting braced frame systems. As part of this study, three full‐scale, two‐story concentrically braced frames in the multi‐story X‐braced configuration were tested. The experiments examined all levels of system performance, up to and including fracture of multiple braces in the frame. Although the past research suggests very limited ductility of SCBFs with HSS rectangular tubes for braces recent one‐story tests with improved gusset plate designs suggest otherwise. The frame designs used AISC SCBF standards and two of these frames designs also employed new concepts developed for gusset plate connection design. Two specimens employed HSS rectangular tubes for bracing, and the third specimen had wide flange braces. Two specimens had rectangular gusset plates and the third had tapered gusset plates. The HSS tubes achieved multiple cycles at maximum story drift ratios greater than 2% before brace fracture with the improved connection design methods. Frames with wide flange braces achieved multiple cycles at maximum story drift greater than 2.5% before brace fracture. Inelastic deformation was distributed between the two stories with the multi‐story X‐brace configuration and top story loading. Copyright © 2010 John Wiley & Sons, Ltd.     

既有钢筋混凝土框架结构的多指标云模型地震损伤评估

目前的既有钢混结构地震损伤研究没有同时考虑不同抗震设计规范差异和耐久性两个因素对结构抗震性能的影响,且损伤指标较简单,在动力损伤分析中也存在局限。基于云模型的特点,提出了包括弹塑性耗能差率、刚度损伤指数、层间位移角和顶点位移角的多元结构损伤状态综合评估方法,能够同时考虑结构各损伤指数的随机性和模糊性。考虑不同版本抗震设计规范造成的结构性能差异和耐久性下降对结构性能的影响,设计3个典型五层钢混框架结构,进行增量动力分析,验证损伤评估方法的准确性。结果表明：随着抗震规范版本的更新,结构的损伤程度有适当减轻;同一结构的损伤程度因混凝土碳化作用先减轻后加重;采用弹塑性耗能差率表征既有结构的地震损伤效果优于刚度损伤指数;基于多指标云模型损伤评估方法获得的云模型综合隶属度和综合损伤值能够更加细化和精确地描述结构损伤状态。     

等位移理论估计高层建筑结构非弹性地震反应的进一步研究

为进一步研究用等位移理论估计高层建筑结构非弹性地震反应,选用五个钢筋混凝土高层结构实例,输入二十条不同场地条件的地震波,采用结构弹性和非弹性地震时程反应分析方法,研究了结构弹性和非弹性最大顶点位移以及最大层间位移角之间的关系。提出可以直接用弹性最大顶点位移估计非弹性最大顶点位移。对于非弹性层间位移角反应,在中、弱非线陛阶段宜可直接用弹性反应结果估计,而在强非线性阶段则需进行一定修正。     

Probabilistic economic seismic loss estimation in steel buildings using post‐tensioned moment‐resisting frames and viscous dampers

The potential of post‐tensioned self‐centering moment‐resisting frames (SC‐MRFs) and viscous dampers to reduce the economic seismic losses in steel buildings is evaluated. The evaluation is based on a prototype steel building designed using four different seismic‐resistant frames: (i) conventional moment resisting frames (MRFs); (ii) MRFs with viscous dampers; (iii) SC‐MRFs; or (iv) SC‐MRFs with viscous dampers. All frames are designed according to Eurocode 8 and have the same column/beam cross sections and similar periods of vibration. Viscous dampers are designed to reduce the peak story drift under the design basis earthquake (DBE) from 1.8% to 1.2%. Losses are estimated by developing vulnerability functions according to the FEMA P‐58 methodology, which considers uncertainties in earthquake ground motion, structural response, and repair costs. Both the probability of collapse and the probability of demolition because of excessive residual story drifts are taken into account. Incremental dynamic analyses are conducted using models capable to simulate all limit states up to collapse. A parametric study on the effect of the residual story drift threshold beyond which is less expensive to rebuild a structure than to repair is also conducted. It is shown that viscous dampers are more effective than post‐tensioning for seismic intensities equal or lower than the maximum considered earthquake (MCE). Post‐tensioning is effective in reducing repair costs only for seismic intensities higher than the DBE. The paper also highlights the effectiveness of combining post‐tensioning and supplemental viscous damping by showing that the SC‐MRF with viscous dampers achieves significant repair cost reductions compared to the conventional MRF. Copyright © 2016 John Wiley & Sons, Ltd.     

Generalized force vectors for multi‐mode pushover analysis of torsionally coupled systems

A generalized multi‐mode pushover analysis procedure was developed for estimating the maximum inelastic seismic response of symmetrical plan structures under earthquake ground excitations. Pushover analyses are conducted with story‐specific generalized force vectors in this procedure, with contributions from all effective modes. Generalized pushover analysis procedure is extended to three‐dimensional torsionally coupled systems in the presented study. Generalized force distributions are expressed as the combination of modal forces to simulate the instantaneous force distribution acting on the system when the interstory drift at a story reaches its maximum value during seismic response. Modal contributions to the generalized force vectors are calculated by a modal scaling rule, which is based on the complete quadratic combination. Generalized forces are applied to the mass centers of each story incrementally for producing nonlinear static response. Maximum response quantities are obtained when the individual frames attain their own target interstory drift values in each story. The developed procedure is tested on an eight‐story frame under 15 ground motions, and assessed by comparing the results obtained from nonlinear time history analysis. The method is successful in predicting the torsionally coupled inelastic response of frames responding to large interstory drift demands. Copyright © 2014 John Wiley & Sons, Ltd.     

双向速度脉冲地震下偏心重力柱核心筒结构的弹塑性地震响应研究

研究速度脉冲地震和结构质量偏心综合不利条件下新型重力柱-核心筒结构体系的弹塑性反应规律。选取速度脉冲和非速度脉冲地震加速度记录各10条,进行地震动双向输入,采用结构非线性分析软件CANNY进行有限元数值分析,研究脉冲型地震和结构质量偏心对新型体系弹塑性地震反应的影响。分析结果表明,速度脉冲型地震作用下各结构的层间位移角、层间剪力和层间扭转角显著高于非速度脉冲地震下的相应值。质量偏心对结构弹塑性抗震需求影响显著,层间位移角和层间扭转角都随着偏心率的增大而增大,而层间剪力则随偏心率的增大呈减小趋势。建议在重力柱-核心筒结构设计中应重视速度脉冲地震和结构偏心的耦合不利影响。     

不同支撑形式高强钢组合偏心支撑抗震性能研究

耗能梁段作为偏心支撑结构的耗能元件,在大震作用下通过弹塑性变形吸收地震能量,保护主体结构处于弹性受力状态。现行规范基于强度的设计理论,为了保证耗能梁段进入塑性或破坏,梁柱构件需要进行放大内力设计,导致截面过大,而且基于强度的设计方法很难保证结构的整体破坏状态。目前,抗震设计越来越重视基于性能的设计思想,该方法能够评估结构的弹塑性反应。对于高强钢组合偏心支撑,其中耗能梁段和支撑采用Q345钢,框架梁柱采用Q460或者Q690高强度钢材,高强钢不仅带来良好的经济效益,而且能够推广高强钢在抗震设防区的应用。利用基于性能设计方法设计了4种不同形式的高强钢组合偏心支撑钢框架,包括K形、Y形、V形和D形,考虑4层、8层、12层和16层的影响。通过Pushover分析和非线性时程分析评估该结构的抗震性能,研究结果表明:4种形式的高强钢组合偏心支撑钢框架具有类似的抗震性能,在罕遇地震作用下,几乎所有耗能梁段均参与耗能,而且层间侧移与耗能梁段转角沿高度分布较为均匀。其中:D形偏心支撑具有最大的抗侧刚度,但延性较差,而Y形偏心支撑的抗侧刚度最弱,但延性最佳。