Isotope–geochemical characterization and geothermometrical modeling of Uttarakhand geothermal field,India

Uttarakhand geothermal area, located in the central belt of the Himalayan geothermal province, is one of the important high temperature geothermal fields in India. In this study, the chemical characteristics of the thermal waters are investigated to identify the main geochemical processes affecting the composition of thermal waters during its ascent toward the surface as well as to determine the subsurface temperature of the feeding reservoir. The thermal waters are mainly Ca–Mg–HCO₃ type with moderate silica and TDS concentrations. Mineral saturation states calculated from PHREEQC geochemical code indicate that thermal waters are supersaturated with respect to calcite, dolomite, aragonite, chalcedony, quartz (SI > 0), and undersaturated with respect to gypsum, anhydrite, and amorphous silica (SI < 0). XRD study of the spring deposit samples fairly corroborates the predicted mineral saturation state of the thermal waters. Stable isotopes (δ¹⁸O, δ²H) data confirm the meteoric origin of the thermal waters with no oxygen-18 shift. The mixing phenomenon between thermal water with shallow ground water is substantiated using tritium (³H) and chemical data. The extent of dilution is quantified using tritium content of thermal springs and non-thermal waters. Classical geothermometers, mixing model, and multicomponent fluid geothermometry modeling (GeoT) have been applied to estimate the subsurface reservoir temperature. Among different classical geothermometers, only quartz geothermometer provide somewhat reliable estimation (96–140 °C) of the reservoir temperature. GeoT modeling results suggest that thermal waters have attained simultaneous equilibrium with respect to minerals like calcite, quartz, chalcedony, brucite, tridymite, cristobalite, talc, at the temperature 130 ± 5 °C which is in good agreement with the result obtained from the mixing model.     

Hydrogeological and mixing process of waters in deep aquifers in arid regions: south east Tunisia

This study addresses the hydrogeochemistry of thermal and cold waters from south east Tunisia. Temperature intervals are 38.5–68 °C and 22–27.8 °C for thermal water and cold water, respectively. Three distinct hydrogeological systems supply water either for irrigation or for drinking; they are: (1) the Continental Intercalaire geothermal aquifer (CI), (2) the Turonian aquifer and (3) the Senonian aquifer. A synthetic study including hydrochemical, hydrogeological and geothermal approaches have been applied in order to evaluate the inter-aquifers water transfer in south east of Tunisia. By using silica geothermometers and saturation indices for different solid phases, estimated thermal reservoir temperature varies between 52 and 87 °C and between 75 and 110 °C, respectively. Based on chemical and thermal data, mixing, which occurs between the ascending deep geothermal water and shallow cold water, is about 57 % cold water.     

A hydrochemical study of the Hammam Righa geothermal waters in north-central Algeria

This study focuses on the hydrochemical characteristics of 47 water samples collected from thermal and cold springs that emerge from the Hammam Righa geothermal field, located in north-central Algeria. The aquifer that feeds these springs is mainly situated in the deeply fractured Jurassic limestone and dolomite of the Zaccar Mount. Measured discharge temperatures of the cold waters range from 16.0 to 26.5 °C and the hot waters from 32.1 to 68.2 °C. All waters exhibited a near-neutral pH of 6.0–7.6. The thermal waters had a high total dissolved solids (TDS) content of up to 2527 mg/l, while the TDS for cold waters was 659.0–852.0 mg/l. Chemical analyses suggest that two main types of water exist: hot waters in the upflow area of the Ca–Na–SO₄ type (Hammam Righa) and cold waters in the recharge zone of the Ca–Na–HCO₃ type (Zaccar Mount). Reservoir temperatures were estimated using silica geothermometers and fluid/mineral equilibria at 78, 92, and 95 °C for HR4, HR2, and HR1, respectively. Stable isotopic analyses of the δ¹⁸O and δD composition of the waters suggest that the thermal waters of Hammam Righa are of meteoric origin. We conclude that meteoric recharge infiltrates through the fractured dolomitic limestones of the Zaccar Mount and is conductively heated at a depth of 2.1–2.2 km. The hot waters then interact at depth with Triassic evaporites located in the hydrothermal conduit (fault), giving rise to the Ca–Na–SO₄ water type. As they ascend to the surface, the thermal waters mix with shallower Mg-rich groundwater, resulting in waters that plot in the immature water field in the Na–K–Mg diagram. The mixing trend between cold groundwaters from the recharge zone area (Zaccar Mount) and hot waters in the upflow area (Hammam Righa) is apparent via a chloride-enthalpy diagram that shows a mixing ratio of 22.6 < R < 29.2 %. We summarize these results with a geothermal conceptual model of the Hammam Righa geothermal field.     

Properties of geothermal resources in Kebilli region, Southwestern Tunisia

The Kebilli region is located in the Southwestern part of Tunisia, and is characterized by the presence of deep and shallow geothermal systems (continental intercalary and complex terminal). Chemical and isotopic contents are used to classify the type and determine the origin of thermal water. An evaluation of reservoir temperature and a possible geothermal fluid mixing are also carried out. Both continental intercalary-deep aquifer and complex terminal-shallow aquifer are of Na–(Ca)–Cl–(SO₄) mixed water type. The use of different geothermometers and the computation of saturation indexes for different solid phases suggests that the thermal reservoir temperature of the continental intercalary is between 92 and 105 °C, while the fluid temperature from the shallow complex terminal aquifer ranges from 50 to 75 °C. Also, the isotopic data indicates the old origin of all groundwater of Southwestern Tunisia. Mixing effects characterizing the continental intercalary and the complex terminal aquifers were identified using δ²H and δ¹⁸O relationship. It appears that the upward movement of thermal water from the deep aquifer to shallow ones is probably due to the abundant fractures in the research area.     

Alteration of fluid properties during the initial operation of a geothermal plant: results from in situ measurements in Groß Schönebeck

Recently, the thermal fluid loop has been established and continuosly operated for 7 days at the geothermal in situ laboratory in Groß Schönebeck (North German Basin). During this initial phase of fluid production, the fluid temperature, measured at the surface, continuously increased until a stable value of about 98 °C was established. Fluid physicochemical properties (pH, redox, density, temperature, and pressure) were measured online and in situ with a newly developed fluid monitoring system (FluMo). Additionally, fluid samples have been collected at various temperatures (in 5–10 °C steps) directly at the production well at about 10 bar pressure. From the pressurized sampling tool, the fluid was directly transferred into a heated autoclave, which allowed filtration (0.2 μm) in the absence of oxygen. Physicochemical parameters [pH, redox, electric conductivity, total dissolved solids (TDS)] as well as acid capacity (K _S 4.3) of these samples have been measured onsite at atmospheric conditions. Concentrations of anions, total organic carbon, and metals were analyzed later in the laboratory. Both, measurements in collected samples or in situ (FluMo) analysis of most the parameters density, electric conductivity, or TDS indicated relatively constant values over the whole production time (1.17–1.18 g · cm^?3, 215–221 mS · cm^?1, 241–260 g · L^?1, respectively). Good correlation was also found for pH values (pH = 6.6–6.9), whereas the redox values varied between ?1 and 46 mV when determined at 25 °C and decreased strongly when measured in situ with increasing temperature (?110 mV at 90 °C). The elemental composition of collected samples remained also relatively constant for most compounds and was clearly higher as compared with samples collected in 2011. Results of this study demonstrate that realistic, comprehensive, and time-resolved physicochemical data can be obtained by FluMo. These detailed data sets can be crucial to understand the complex geochemical processes in a thermal water loop and eventually to take required measures on time.     

Characteristics of the geothermal water in Changbai Mountain volcanic region,northeast of China

Geothermal water is plentiful in Changbai Mountain region, northeastern China, due to the volcanic activities and widespread faults. For the exploration of geothermal resources, this study uses quartz and cation geothermometer to estimate the temperatures of the geothermal reservoir and uses the tubular models to evaluate the thermal gradient. The hydrogeochemical characteristics of the geothermal resources were also evaluated by hydrogeochemical analysis. The results showed that the geothermal reservoir temperatures of the four major thermal springs in Changbai Mountain region range from 72 to 169 °C. The average geothermal reservoir temperatures of Jinjiang hot springs, Changbai hot springs I, Xianrenqiao hot springs, and Changbai hot springs II are 129.25, 169, 89, and 73.67 °C, respectively. The geothermal gradient values of the four major thermal springs have different characteristics. The geothermal gradient values of Jinjiang hot springs and Changbai hot springs I are 4.6 and 3.1 °C/100 m, respectively. The geothermal gradient values of Xianrenqiao thermal springs and Changbai thermal springs II are both lower than 1.5 °C/100 m, with the values of 1.1 and 1.4 °C/100 m. And the geothermal gradients are influenced by Changbai Mountain Tianchi volcano. In addition, the water chemical analyses showed that the geothermal water types are HCO₃-Na with higher concentrations of Na⁺, Cl^?, SO₄ ^2?, TDS, and HCO₃ ^? than the non-thermal waters, which suggested a deep and long water cycle of the thermal water, and therefore a sufficient water-rock interaction.     

Mixing of geothermal and non-geothermal fluids in shallow aquifers in the Germencik-Nazilli area,Büyük Menderes Basin (SW Turkey)

This study observes groundwater hydrochemical characteristics during mixing between geothermal and non-geothermal fluids in Germencik–Nazilli area in the Büyük Menderes Basin (SW Turkey). Hydrogeochemical features of 32 non-geothermal, geothermal and surface samples were studied. The mean temperatures of the geothermal reservoirs are calculated to be 150–240 °C in Germencik field, based on Na-K-Mg geothermometry. Hydrochemical characteristics of Germencik geothermal fluid differ from non-geothermal fluids, mainly Na-Cl-HCO₃-type geothermal fluid, while non-geothermal fluid is mostly Ca-Mg-HCO₃-SO₄ type. High contents of some minor elements in geothermal fluids are most likely sourced from prolonged water-rock interaction, reflecting the signals of flow paths and residence times. A mass-balance approach was used to calculate mixing ratios between geothermal and non-geothermal fluids based on B, Cl and Na concentrations. Germencik field is considerably characterised by rising geothermal fluids and overlying non-geothermal fluids. The amount of water stored in the Quaternary aquifer evolved from a deep thermal source is low in Germencik (.5–40% geothermal fluid in non-geothermal wells). Mixing between geothermal and non-geothermal fluids has been caused by groundwater utilisation practices and is increased close to active faults. Irrigation of the shallow groundwater composition is considered as influx of low-temperature geothermal fluid.     

Geothermal energy potential of Tulsishyam thermal springs of Gujarat,India

Tulsishyam thermal springs are located in the Saurashtra region of Gujarat, India with discharge temperatures varying from 39 to 42 °C. The pH of these thermal springs varies from 7.1 to 7.4, indicating neutral character. Though these thermal springs propagate through the near surface layer of Deccan basalt, detailed geochemical analysis of the thermal waters using Piper diagram suggests that the water is interacting with the granitic basement rock. Silica and cation geothermometry estimates have reservoir temperature in the range of 138 to 207 °C categorizing it into a low to moderate enthalpy geothermal system. Furthermore, the area has high heat flow values of 53–90 mW/m² because of shallow Moho depth. The prevailing conditions suggest that the geothermal energy can potentially be exploited through an enhanced geothermal system (EGS). The study also indicates different mineral phases that may precipitate out of water during exploitation of geothermal energy and it should be taken into account while designing an EGS for the area.     

Hydrochemical characteristics and mixing behavior of thermal springs along the Bijiang River in the Lanping basin of China

The Lanping–Simao basin characterized by the occurrence of hydrothermal activities in the northern part of the basin is the largest depression basin in western Yunnan Province. Hot springs outcrop in the semi-drought red layers (TDS, 0.644–8.17 g/L). Mixing with shallow cold water in the flow system is the dominant hydrogeological process leading to the decrease in thermal water temperature and complex hydrochemical compositions with water types ranging from HCO₃–Ca·Mg to Cl–Na type. According to the silicon concentration and enthalpy evaluation, the geothermal reservoir temperatures are estimated between 118 and 204 °C, and the mixing ratio between cold and thermal groundwater is 0.76 on the average. The high concentrations of Na and Cl indicate that there is some well-mineralized cold water in the flow system circulating to the upward migration path accompanied with intense water–rock reactions in the fault developed basin. Ca and SO₄ originate from progressively longer flow path owing to the poor solubility of gypsum, anhydrite and Ca–montmorillonite. Hierarchical clustering and multivariate statistical methods recognized three hot springs groups and four parameters groups which classified the reservoir environment into two situations, one is in the high-pressure environment with intense degassing, and the other is in the lower pressure with weak minerals migration.     

Impact of CO<Subscript>2</Subscript> injection rate on heat extraction at the HDR geothermal field of Zhacanggou,China

CO₂ is now considered as a novel heat transmission fluid to extract geothermal energy. It can achieve the goal of energy exploitation and CO₂ geological sequestration. Taking Zhacanggou as research area, a “Three-spot” well pattern (one injection with two production), “wellbore–reservoir” coupled model is built, and a constant injection rate is set up. A fully coupled wellbore–reservoir simulator—T2Well—is introduced to study the flow mechanism of CO₂ working as heat transmission fluid, the variance pattern of each physical field, the influence of CO₂ injection rate on heat extraction and the potential and sustainability of heat resource in Guide region. The density profile variance resulting from temperature differences of two wells can help the system achieve “self-circulation” by siphon phenomenon, which is more significant in higher injection rate cases. The density of CO₂ is under the effect of both pressure and temperature; moreover, it has a counter effect on temperature and pressure. The feedback makes the flow process in wellbore more complex. In low injection rate scenarios, the temperature has a dominating impact on the fluid density, while in high rate scenario, pressure plays a more important role. In most scenarios, it basically keeps stable during 30-year operation. The decline of production temperature is <5 °C. However, for some high injection rate cases (75 and 100 kg/s), due to the heat depletion in reservoir, there is a dramatic decline for production temperature and heat extraction rate. Therefore, a 50-kg/s CO₂ injection rate is more suitable for “Three-spot” well pattern in Guide region.     

Occurrence and evolution of the Xiaotangshan hot spring in Beijing, China

Thermal groundwater occurs in bedrock aquifers consisting of the dolomite of the Wumishan Group of the Jixianin System and the Cambrian carbonate in the Xiaotangshan geothermal field near the northern margin of the North China Plain, China. The hot water in the geothermal field of basin-type discharges partly in the form of the Xiaotangshan hot spring under natural conditions. The hot water has TDS of less than 600 mg/L and is of Na·Ca-HCO₃ type. The geothermal water receives recharge from precipitation in the mountain area with elevation of about 500 m above sea level to the north of the spring. Thermal groundwater flows slowly south and southeast through a deep circulation with a residence time of 224 years estimated with the Ra–Rn method. The Xiaotangshan hot spring dried up in the middle of the 1980s owing to the increasing withdrawal of the hot water in the geothermal field in the past decades. The water level of the geothermal system still falls continually at an annual average rate of about 2 m, although water temperature changes very little, indicating that the recharge of such a geothermal system of basin-type is limited. Over-exploitation has a dramatic impact on the geothermal system, and reduction in exploitation and reinjection are required for the sustainable usage of the hot water.     

A preliminary study on the potential of the geothermal resources around the Gulf of Suez, Egypt

The Gulf of Suez is characterized by the presence of many hot springs and deep thermal wells scattered around its coastal areas. So it is considered one of the promised geothermal areas in Egypt. In this study, the main emphasis is to investigate the geothermal potential around the Gulf of Suez using the available logging and geothermometer datasets. The temperature profiles and well logging data of some hot springs and deep wells around or within the coastal area of the Gulf of Suez are used in this study. The temperature profiles are analyzed and some important thermophysical properties are estimated (geothermal gradient, thermal conductivity, heat flow, and specific heat capacity). Such analysis revealed that a medium to high geothermal gradient (22.0–30°C/Km) is given for the Gulf of Suez as a whole, with some spots of much higher gradient in the order of 35.0–44°C/Km (Ras Fanar and Hammam Faraun areas). The compiled thermal plots show that the thick evaporites and rock salt lithology, which is a major constituent in this area, attain the highest thermal conductivity (>3.10 W/m/K) and heat flow (>90 mW/m²) and the lowest specific heat capacity (<0.30 J/kg/K). The available gamma ray and the natural gamma ray spectroscopy logs are used to conduct a radioactive-based heat generation study using the characteristic radioactive nature of some elements like; ²³⁸U, ²³⁵U, ²³²Th, and of the isotope of ⁴⁰K. A good linearity is observed between the heat production (A in microwatt per cubic meter) and the gamma ray (API) along a wide range of datasets (0–150 API) in all wells. The heat production factor increases in the carbonate lithology (up to 3.20?μW/m³) and is proportional to the shale volume. A geothermometer-based study is used to estimate the subsurface formation temperature and heat flow from the geochemical analysis of some water samples collected from the studied hot springs. The estimated thermal parameters are in harmony with the regional thermal regime concluded form logging data. A thermal basin growth study, in relation to the clay diagenesis is conducted concerning the thermal effects that take place with depth giving rise to another clay mineral (illite). Furthermore, a number of 2D thermal–burial history diagrams are constructed for the complied sections of some of the studied areas to show the vertical distribution of the estimated petrothermal properties. A reserve evaluation study is carried out to estimate the economic geothermal capacity of these hot springs to be used as alternative clean source for possible energy production (electricity) and other low-temperature purposes.     

Geochemical and isotope hydrological characterisation of geothermal resources at Godavari valley,India

Thermal waters at the Godavari valley geothermal field are located in the Khammam district of the Telangana state, India. The study area consists of several thermal water manifestations having temperature in the range 36–76 °C scattered over an area of ~35 km². The thermal waters are Na–HCO₃ type with moderate silica and TDS concentrations. In the present study, detailed geochemical (major and trace elements) and isotope hydrological investigations are carried out to understand the hydrogeochemical evolution of these thermal waters. Correlation analysis and principal component analysis (PCA) are performed to classify the thermal waters and to identify the different geochemical processes controlling the thermal water geochemistry. From correlation matrix, it is seen that TDS and EC of the thermal springs are mainly controlled by HCO₃ and Na ions. In PCA, thermal waters are grouped into two distinct clusters. One cluster represents thermal waters from deeper aquifer and other one from shallow aquifer. Lithium and boron concentrations are found to be similar followed by rubidium and caesium concentrations. Different ternary plots reveal rock–water interaction to be the dominant mechanism for controlling trace element concentrations. Stable isotopes (δ¹⁸O, δ²H) data indicate the meteoric origin of the thermal waters with no appreciable oxygen-18 shift. The low tritium values of the samples originating from deeper aquifer reveal the long residence time (>50 years) of the recharging waters. XRD results of the drill core samples show that quartz constitutes the major mineral phase, whereas kaolinite, dolomite, microcline, calcite, mica, etc. are present as minor constituents. Quartz geothermometer suggests a reservoir temperature of 100 ± 20 °C which is in good agreement with the values obtained from K–Mg and Mg-corrected K–Mg–Ca geothermometers.     

Mixing geochemistry of cold water around non-volcanic thermal springs in high-grade metamorphic terrain,Sri Lanka

A geochemical survey was conducted on thermal water and cold water around non-volcanic geothermal fields at Mahaoya and Marangala in Sri Lanka. One hundred forty-two samples were analyzed for fifteen selected irons to investigate geochemical relationships resulting from water-rock interactions and mixing. Based on measurements using a Na-K-Mg geothermometer, the maximum temperatures of thermal reservoirs were estimated to be 148 °C in Mahaoya and 191 °C in Marangala, which were higher values than those obtained using Na-Li and Li-Mg geothermometers. This suggests that the reservoirs extend from intermediate to deep levels. Hydrogeochemistry of thermal waters is distinct from that of cold water; higher contents of Na, K, Cl, F, SO_4, and TDS in thermal water are most likely due to the dissolution of feldspar, mica, and sulfide minerals in the granitic rocks. Conversely, lower values of Fe, Mg, Cu, Zn, and Pb imply less ferromagnesian minerals in the basement. Classification based on major ions reveals a Na-K-SO₄ type of thermal water for Mahaoya and Marangala. Cold water is dominated by the Na-K-HCO₃ type, which indicates deep groundwater influence by iron exchange. Non-mixing cold water indicates a Ca-HCO₃ type. In general, chemistry of cold water wells (<400 m) close to the thermal water changes significantly due to direct mixing of thermal water and cold water. In comparison, a contrasting action occurs with increasing distance from the geothermal field. Gradual decline of SO₄ with increasing distance from thermal water may indicate a trend of clear oxidation. However, the chemistry of more distant wells demarcates deep circulations through fractures and faults in the basement.     

Hydrochemistry of geothermal water in Tianshui and adjacent area, Gansu province, China

A geochemical study on thermal water has been carried out in Tianshui and its adjacent area, Gansu province, China. Chemical and isotopic contents were employed in the investigation on the origin and evolution of thermal water and the evaluation of reservoir temperature in the geothermal systems. Thermal waters in Wushan and Tianshui are characterized by outlet temperatures from 15 to 38°C and low TDS (226?C255?mg/L), defined as bicarbonate water. Its origin may be attributed to the interaction between meteoric rain, biotite plagioclase gneiss and carbonate reservoir rocks. In contrast, thermal waters in Tongwei and Qingshui have higher outlet temperatures of 25?C54.2°C and a moderate TDS of 915?C1,793?mg/L, regarded as sulfate waters. These sulfate waters may arise from the interaction between meteoric water, granite and amphogneiss. Isotopic data presented here suggest that thermal waters in the study area have a meteoric origin without being significantly effected by water?Crock isotope exchange. Chemical geothermometry indicates the existence of a deep geothermal reservoir of low-to-medium enthalpy (70?C111°C) in the Tianshui study area.     

Hydrochemistry and geothermometry of thermal groundwater of southeastern Tunisia (Gabes region)

Given the vital importance of water and energy in desert regions, we undertook a study dealing with the deep reservoirs in Gabes area, which is located in the southeastern part of Tunisia. Geothermal resources are taken from the Intercalary Continental [or Continental Intercalaire (CI)], known as the largest deep aquifer in Tunisia and are used in a number of applications, mainly in agriculture. Previous investigations performed on the thermal waters of this area focused on the genesis of the deep waters with regard to the thermal features of geothermal reservoirs. A more detailed investigation has been carried out, considering both deep and shallow waters. In order to estimate the potential temperatures of deep reservoir in the Gabes area, we developed a synthetic study including chemical geothermometers, multiple mineral equilibrium approach, and other approaches. Chemical types of the thermal waters and effects of mixing between shallow cold waters with deep thermal waters were also discussed. In fact, the application of Na–K–Mg diagram relative to deep geothermal reservoir capitulate estimated temperatures (about 90°C). In addition, the multiple mineral equilibrium approach submits a similar estimated temperature ranging between 65 and 70°C, showing a disequilibrium status which indicates a possibly mixing with surface water. Indeed, wells exploiting the CI aquifer in the south part of the studied area showed the same characteristics, corroborating the reliability of the applied methods.     

河间潜山地热资源开发方案数值模拟

古潜山地热资源具备岩溶孔隙发育程度高、热储面积厚度大、地热水储量大的优点。冀中坳陷内古潜山分布密集且地热资源丰富, 河间潜山位于冀中坳陷饶阳凹陷中东部, 具有良好的地热地质条件, 开发潜力巨大。本文基于河间潜山及其周缘地区测井资料、岩石热物性并进行了计算, 发现其地温梯度为29.8 ℃/km到44.5 ℃/km之间, 平均值为40.7 ℃/km。大地热流值介于64.8~80.6 mW/m2之间, 平均值为 73.4 mW/m2。通过水热耦合模拟方法模拟选定的地热资源有利区的温度变化, 结果发现河间潜山合理的开采井距为800 m, 合理开采量为60 L/s, 回灌温度为35 ℃, 总可开采量为6.32×1016 J, 单年可开采量为 6.32×1014 J, 可供暖面积为1.22×106 m2, 对于冀中坳陷潜山地热资源的开发利用具有一定的指导意义。     

Geochemical and isotopic characteristics of fluids in the Niutuozhen geothermal field,North China

Niutuozhen geothermal field is located in the Jizhong graben, belonging to the northern part of Bohai Bay Basin in North China. Chemical and isotopic analyses were carried out on 14 samples of the geothermal fluids discharged from Neogene Minghuazhen (Nm), Guantao (Ng), and Jixianian Wumishan (Jxw) formations. The δ²H and δ¹⁸O in water, δ¹³C in CH₄, δ¹³C in CO₂, and ³He/⁴He ratio in the gases were analyzed in combination with chemical analyses on the fluids in the Niutuozhen geothermal field. The chemical and isotopic compositions indicate a meteoric origin of the thermal waters. The reservoir temperatures estimated by chemical geothermometry are in the range between 60 and 108 °C. The results show that the gases are made up mainly by N₂ (18.20–97.42 vol%), CH₄ (0.02–60.95 vol%), and CO₂ (0.17–25.14 vol%), with relatively high He composition (up to 0.52 vol%). The chemical and isotopic compositions of the gas samples suggest the meteoric origin of N₂, predominant crustal origins of CH₄, CO₂, and He. The mantle-derived He contributions are calculated to be from 5 to 8% based on a crust–mantle binary mixing model. The deep temperatures in the Jxw reservoir were evaluated based on gas isotope geothermometry to be in the range from 141 to 165 °C. The mantle-derived heat fraction in the surface heat flow is estimated to be in the range of 48–51% based on ³He/⁴He ratios.     

Hydrochemical and isotopic properties of Heybeli geothermal area (Afyon,Turkey)

The thermal waters at the Heybeli (K?z?lkirse) low-temperature geothermal field located in the Afyonkarahisar Province (western Turkey) are discharged from Paleozoic recrystallized limestone. The temperature, specific electrical conductivity, and pH values of the thermal waters are within the range of 28.9 to 54.7 °C, 587 to 3580 μS/cm, and 6.32 to 7.37, respectively. The Heybeli geothermal system is fed by meteoric waters. The waters are heated at depth by high geothermal gradient caused by the neotectonic activity in the deep and ascend to the surface through fractures and faults by convection. The thermal waters are of Na-Ca-HCO₃-SO₄ type and their chemical composition of the waters is mainly controlled by water-rock interaction and mixing processes. The δ¹⁸O, δ²H and tritium compositions show that the thermal waters are of meteoric origin and the residence time at the reservoir is longer than 50 years. Isotope data (δ³⁴S and δ¹³C) indicate recrystallized limestones as origin of CO₂ and structural substitution of sulfate into marine carbonates (CAS) as origin of sulfur. Chemical, \( {\updelta}^{18}{\mathrm{O}}_{\left({\mathrm{SO}}_4-{\mathrm{H}}_2\mathrm{O}\right)} \) isotope geothermometers and mineral equilibrium diagrams applied to thermal waters gave reservoir temperatures between 62 and 115 °C. Saturation index calculations show that the most expected minerals causing scaling at outflow conditions during the production and utilization of Heybeli geothermal waters are calcite, aragonite, dolomite, quartz, and chalcedony.     

Geochemical patterns and origin of alkaline thermal waters in Central Greece (Platystomo and Smokovo areas)

This study investigates the origin and chemical composition of the thermal waters of Platystomo and Smokovo areas in Central Greece as well as any possible relationships of them to the neighboring geothermal fields located in the south-eastern part of Sperchios basin. The correlations between different dissolved salts and the temperature indicate that the chemical composition of thermal waters are controlled by, the mineral dissolution and the temperature, the reactions due to CO₂ that originates possibly by diffusion from the geothermal fields of Sperchios basin and the mixing of thermal waters with fresh groundwater from karst or shallow aquifers. Two major groups of waters are recognized on the basis of their chemistry: thermal waters of Na–HCO₃–Cl type and thermal waters mixed with fresh groundwater of Ca–Mg–Na–HCO₃ type. All thermal waters of the study area are considered as modified by water–rock interaction rainwater, heated in depth and mixed in some cases with fresh groundwater when arriving to the surface. Trace elements present low concentrations. Lithium content suggests discrimination between the above two groups of waters. Boron geochemistry confirms all the above remarks. Boron concentration ranges from 60 μg L^?1 to 10 mg L^?1, while all samples’ constant isotopic composition (δ¹¹B ≈ 10 ‰) indicates leaching from rocks. The positive correlation between the chemical elements and the temperature clearly indicates that much of the dissolved salts are derived from water–rock interactions. The application of geothermometers suggests that the reservoir temperature is around 100–110 °C. Chalcedony temperatures are similar to the emergent temperatures and this is typical of convective waters in fault systems in normal thermal gradient areas.