Direct bed shear stress measurements in bore-driven swash

Direct measurements of bed shear in the swash zone are presented. The data were obtained using a shear plate in medium and large-scale laboratory bore-driven swash and cover a wide range of bed roughness. Data were obtained across the full width of the swash zone and are contrasted with data from the inner surf zone. Estimates of the flow velocities through the full swash cycle were obtained through numerical modelling and calibrated against measured velocity data. The measured stresses and calculated flow velocities were subsequently used to back-calculate instantaneous local skin friction coefficients using the quadratic drag law. The data show rapid temporal variation of the bed shear stress through the leading edge of the uprush, which is typically two–four times greater than the backwash shear stresses at corresponding flow velocity. The measurements indicate strong temporal variation in the skin friction coefficient, particularly in the backwash. The general behaviour of the skin friction coefficient with Reynolds number is consistent with classical theory for certain stages of the swash cycle. A spatial variation in skin friction coefficient is also identified, which is greatest across the surf-swash boundary and likely related to variations in local turbulent intensities. Skin friction coefficients during the uprush are approximately twice those in the backwash at corresponding Reynolds number and cross-shore location. It is suggested that this is a result of the no-slip condition at the tip leading to a continually developing leading edge and boundary layer, into which high velocity fluid and momentum are constantly injected from the flow behind and above the tip region. Finally, the measured stress data are used to determine the asymmetry and cross-shore variation in potential sediment transport predicted by three forms of sediment transport formulae.     

On the cross-shore profile change of gravel beaches

This paper investigates cross-shore profile changes of gravel beaches, with particular regard to discussing the tendency for onshore transport and profile steepening in the swash zone. The discussion includes observed morphological changes on a gravel beach from experimental investigations at the Large Wave Flume (GWK) in Hanover, Germany. During the tests all the profile changes occurred in the swash zone, resulting in erosion below the still water line (SWL) and formation of a berm above the SWL. We investigate the profile evolution evaluating the transport rates from a bed load sediment transport formulation coupled with velocities calculated from a set of Boussinesq equations that have been validated for its use in the surf and swash zones [Lynett, P.J., Wu, T.-R., and Liu, L.-F., P., 2002. Modelling wave runup with depth-integrated equations. Coastal Engineering, 46, 89–107; Otta, A.K., and Pedrozo-Acuña, A., 2004. Swash boundary and cross-shore variation of horizontal velocity on a slope. In: J.M. Smith (Editor), Proceedings 29th International Conference on Coastal Engineering. World Scientific, Lisbon, Portugal, pp. 1616–1628]. We discuss the influence of bottom friction on the predicted profiles, using reported friction factors from experimental studies. It is shown that the use of a different friction factor within a realistic range in each phase of the swash (uprush and backwash) improves prediction of the beach profiles, although quantitative agreement between the measured and computed profile evolutions is not satisfactory. Furthermore, if the friction factor and the transport efficiency (C) of the sediment transport formulation are kept the same in the uprush and backwash, accurate representation of profile evolution is not possible. Indeed, the features of the predicted profiles are reversed. However, when the C parameter is set larger during the uprush than during the backwash, the predicted profiles are closer to the observations. Differences between the predicted profiles from setting non-identical C-values and friction factors for the swash phase, are believed to be linked to both the infiltration effects on the flow above the beachface and the more accelerated flow in the uprush.     

A Lagrangian model for boundary layer growth and bed shear stress in the swash zone

A new model for the boundary layer development and associated skin friction coefficients and shear stress within the swash zone is presented. The model is developed within a Lagrangian reference frame, following fluid trajectories, and can be applied to both laminar flow and smooth turbulent flow. The model is based on the momentum integral approach for steady, flat-plate boundary layers, with appropriate modifications to account for the unsteady flow regime and flow history. The model results are consistent with previous measurements of bed shear stress and skin friction coefficients within the swash zone. These indicate strong temporal and spatial variation throughout the swash cycle, and a clear distinction between the uprush and backwash phase. This variation has been previously attributed the unsteady flow regime and flow history effects, both of which are accounted for in the new model. Fluid particle trajectories and velocity are computed using the non-linear shallow water wave equations and the boundary layer growth across the entire swash zone is estimated. Predictions of the bed shear stress and skin friction coefficients agree reasonably well with direct bed shear stress measurements reported by Barnes et al. (Barnes, M.P., O’Donaghue, T., Alsina, J.M., Baldock, T.E., 2009. Direct bed shear stress measurements in bore-driven swash. Coastal Engineering 56 (8), 853–867) and, for a given flow velocity, give stresses which are consistent with the bias toward uprush sediment transport which has consistently been observed in measurements. The data and modelling suggest that the backwash boundary layer is initially laminar, which results in the late development of significant bed shear during the backwash, with a transition to a turbulent boundary layer later in the backwash. A new conceptual model for the boundary layer structure at the leading edge of the swash is proposed, which accounts for both the no-slip condition at the bed and the moving wet–dry interface. However, further development of the Lagrangian Boundary Layer Model is required in order to include bore-generated turbulence and to account for variable roughness and mobile beds.     

Process-based model for nearshore hydrodynamics, sediment transport and morphological evolution in the surf and swash zones

Hydrodynamics and sediment transport in the nearshore zone were modeled numerically taking into account turbulent unsteady flow. The flow field was computed using the Reynolds Averaged Navier–Stokes equations with a k–ε turbulence closure model, while the free surface was tracked using the Volume-Of-Fluid technique. This hydrodynamical model was supplemented with a cross-shore sediment transport formula to calculate profile changes and sediment transport in the surf and swash zones. Based on the numerical solutions, flow characteristics and the effects of breaking waves on sediment transport were studied. The main characteristic of breaking waves, i.e. the instantaneous sediment transport rate, was investigated numerically, as was the spatial distribution of time-averaged sediment transport rates for different grain sizes. The analysis included an evaluation of different values of the wave friction factor and an empirical constant characterizing the uprush and backwash. It was found that the uprush induces a larger instantaneous transport rate than the backwash, indicating that the uprush is more important for sediment transport than the backwash. The results of the present model are in reasonable agreement with other numerical and physical models of nearshore hydrodynamics. The model was found to predict well cross-shore sediment transport and thus it provides a tool for predicting beach morphology change.     

Estimating swash zone friction coefficients on a sandy beach

Video-based swash motions from three studies (on two separate beaches) were analyzed with respect to theoretical swash trajectories assuming plane beach ballistic motions under quadratic friction. Friction coefficient values for both the uprush and backwash were estimated by comparing measured swash space–time trajectories to these theoretical expectations given an initial velocity and beach slope. Observations were made spanning high tides, and in one case, during a light rain. Analysis of over 4500 individual swash events showed that the uprush friction coefficient was nearly constant during all three studies with a mean value of roughly 0.007 and showed no trends over a tidal cycle. In contrast, backwash friction coefficient values varied over the tidal cycles ranging between 0.01 and 0.07 with minimum values corresponding to the highest tides. Although these values are close to the theoretical estimates based on a Law of the Wall formulation and values commonly referenced in the literature, these observations show a consistent tendency for backwash friction estimates to greatly exceed uprush friction estimates. The disparity between uprush and backwash friction coefficients can be partially attributed to the exclusion of a pressure gradient term in the ballistic model. However, results indicate that backwash friction coefficients adjusted to account for this effect may be three times larger than the uprush friction values during lower tides. This tidal dependence for backwash friction coefficients is attributed to a complex interaction between swash infiltration and entrained sediment loads. These findings imply that friction estimates (necessary for sediment transport calculations and hydrodynamic predictions) based solely on grain roughness may not be correct for backwash flows.     

On the transport of suspended sediment by a swash event on a plane beach

We develop solutions for the transport of suspended sediment by a single swash event following the collapse of a bore on a plane beach, and we investigate the morphodynamical role that such transport may play. Although the intrinsic asymmetry between uprush and backwash velocities tends to encourage the export of sediment, we find that swash events may be effective in distributing across the swash zone much or all of the sediment mobilised by bore collapse; additionally, settling lag effects may promote a weak onshore movement of sediment. We quantify both effects in terms of the properties of the sediment and of the swash event, and comment on the relationship between our findings and recent field studies of swash zone sediment transport.     

Laboratory and numerical study of dambreak-generated swash on impermeable slopes

New laboratory experiments have produced detailed measurements of hydrodynamics within swash generated by bore collapse on a steep beach. The experiments are based on a dambreak rig producing a highly repeatable, large-scale swash event, enabling detailed measurements of depths and velocities at a number of locations across the swash zone. Experiments were conducted on two beaches, differentiated by roughness. Results are presented for uprush shoreline motion, flow depths, depth-averaged velocity, velocity profiles and turbulence intensity. Estimates of the time- and spatially-varying bed shear stress are obtained via log-law fitting to the velocity profiles and are compared with the shear plate measurements of Barnes et al. (2009) for similar experimental conditions. Experimental results are compared with model predictions based on a NLSWE model with momentum loss parameterised using the simple quadratic stress law in terms of the depth-averaged velocity. Predicted and measured flow depths and depth-averaged velocities agree reasonably well for much of the swash period, but agreement is not good at the time of bore arrival and towards the end of the backwash. The parameterisation of total momentum loss via the quadratic stress law cannot adequately model the swash bed shear stress at these critical times.     

The role of bore collapse and local shear stresses on the spatial distribution of sediment load in the uprush of an intermediate-state beach

Spatial variations in sediment load in the swash uprush and textural properties of sediment in transport were evaluated to investigate the mechanisms responsible for sediment transport during wave uprush. Four streamer traps were deployed at 2.0-m intervals across the swash zone of a sheltered, microtidal sandy beach at Port Beach, Western Australia, over a 4-day period. During these trapping experiments, offshore significant wave heights were 0.3–0.5 m and wave periods were about 10 s. The average width of the uprush zone was 6.9 m and the average uprush duration was 5.9 s. Cross-shore distributions of sediment load for 70 uprush events reveal a maximum in sediment load landward of the base of the swash (at about 20% of swash width) during single events and a maximum closer to mid-swash (at about 40% of swash width) during multiple events characterized by swash interactions. Settling velocity distributions of trap samples during individual uprush events are similar to distributions found on the beach surface, with the lowest settling velocities (finest sediments) near the base of the swash zone and maximum settling velocities (coarsest sediments) around the mid-swash position. It was found that sediment transport during wave uprush occurs through two distinct mechanisms: (1) sediment entrainment during bore collapse seaward of the base of the swash zone and subsequent advection of this bore-entrained sediment up the beach by wave uprush; and (2) in situ sediment entrainment and transport induced by local shear stresses during wave uprush. Both mechanisms are considered important, but the first mechanism is considered most significant during the early stages of wave uprush when sediment is transported mainly in suspension, while the second mechanism is likely to dominate the mid- to later stages of wave uprush when sediment is transported mainly by sheet flow. The relative importance of the two mechanisms will vary between different beaches with the morphodynamic state of the beach (reflective versus dissipative) expected to play a major role.     

Swash overtopping and sediment overwash on a truncated beach

New experimental laboratory data are presented on swash overtopping and sediment overwash on a truncated beach, approximating the conditions at the crest of a beach berm or inter-tidal ridge-runnel. The experiments provide a measure of the uprush sediment transport rate in the swash zone that is unaffected by the difficulties inherent in deploying instrumentation or sediment trapping techniques at laboratory scale. Overtopping flow volumes are compared with an analytical solution for swash flows as well as a simple numerical model, both of which are restricted to individual swash events. The analytical solution underestimates the overtopping volume by an order of magnitude while the model provides good overall agreement with the data and the reason for this difference is discussed. Modelled flow velocities are input to simple sediment transport formulae appropriate to the swash zone in order to predict the overwash sediment transport rates. Calculations performed with traditional expressions for the wave friction factor tend to underestimate the measured transport. Additional sediment transport calculations using standard total load equations are used to derive an optimum constant wave friction factor of f_w = 0.024. This is in good agreement with a broad range of published field and laboratory data. However, the influence of long waves and irregular wave run-up on the overtopping and overwash remains to be assessed. The good agreement between modelled and measured sediment transport rates suggests that the model provides accurate predictions of the uprush sediment transport rates in the swash zone, which has application in predicting the growth and height of beach berms.     

The influence of swash infiltration–exfiltration on beach face sediment transport: onshore or offshore?

Measurements were obtained from the swash-zone of a high-energy macrotidal dissipative beach of pore-pressure at four levels below the bed, and cross-shore velocity at a single height above the bed. Time-series from relatively high (H_s≈2.0 m) energy conditions were chosen for analysis from the mid-swash-zone at high tide. Calculation of upwards-directed pore-pressure gradients shows that, in this case, fluidisation of the upper layer of sediment, leading to enhanced backwash transport, is unlikely. An apparent conflict exists in the literature regarding the net effect of infiltration–exfiltration on the sediment transport, through the combined effects of stabilisation–destabilisation and boundary layer modification. This is examined for the data collected using a modified Shields parameter. Inferred instantaneous transport rates integrated over a single swash cycle show a decrease in uprush transport of 10.5% and an increase in backwash transport of 4.5%. Sensitivity tests suggest that there is a critical grain size at which the influence of infiltration–exfiltration changes from offshore to onshore. The exact value of this grain size is highly sensitive to the method used to estimate the friction factor.     

Sedimentology and morphodynamics of a macrotidal beach, Pendine Sands, SW Wales

The foreshore of Pendine Sands forms the seaward part of an extensive, sandy coastal barrier in a shallow Carmarthen Bay, SW Wales. The sedimentological features of the macrotidal foreshore reflect a tide-induced modification of nearshore wave characteristics. As the tide ebbs, the breaker height may decrease, the surf zone widens and becomes increasingly dissipative, and swash/backwash velocities diminish. A concomitant change from plunging to spilling breakers and increasingly symmetrical swash zone flows are associated with a decreasing beach gradient.

A zero net transport model demonstrates that the beach profile is self-stabilising in the short-term, and periodic levelling has shown that the beach is in long-term equilibrium with prevailing conditions, though this does not preclude a significant dynamic response to changing tides and waves.

The flow regimes of wave-generated currents decline as the tide ebbs, and normal beach processes do not usually affect the lower foreshore. Accordingly, there is an overall seaward-fining of the primary framework component of the sands. In more detail, this framework component displays a slight seaward-coarsening across an upper foreshore dominated by high water swash and surf; a rapid seaward-fining across the mid-foreshore in response to the ebb-attenuating swash zone flow velocities; and a slight seaward-fining across the lower foreshore under the action of nearshore shoaling waves. Bedforms vary from a swash/backwash emplaced flat bed across the upper foreshore to the small ripples of nearshore asymmetric oscillatory flows across the lower foreshore.

The surface sediment veneer is not representative of the subsurface sediments which form in response partly to fairweather conditions, partly to storms. The upper foreshore is characterised by swash/backwash emplaced plane bedding in fine sands frequently disrupted by bubble cavities. The mid-foreshore is composed of coarser-grained shelly traction clogs arranged as landward- and seaward-dipping large-scale cross bedding and/or plane bedding; these are probably storm breaker/surf deposits. The lower foreshore, though partially and sometimes totally bioturbated, shows landward-dipping small-scale cross bedding in very fine sands sorted by nearshore shoaling waves.

Tide- and storm-induced modification of the nearshore flow regimes therefore produces a distinctive shore-normal array of sedimentary facies. Each facies is characterised by diagnostic textural and structural signatures. A prograding sequence of such macrotidal deposits would be similar to, but more extensive than, a comparable microtidal sequence.     

Instruments for investigating shore and nearshore processes

Abstract

On shingle beaches, changes in foreshore elevation and sediment distribution landward of the break point are produced largely by variations in the uprush and backwash of waves. However, very little is known about the forces active in this zone.

A field instrument system which senses and records some of the parameters thought to influence beach erosion and deposition in this zone has been constructed. The equipment is also suitable for the investigation of a number of other shore and nearshore processes including erosion on sandy and rocky shores, and flow processes affecting littoral biological communities.

In the swash zone two sensing heads, a dynamometer and a depth recorder, sense variations in uprush and backwash velocities, energies, discharges, and depths of flow. Both devices are electromechanical and are coupled to a recording unit on land by PVC‐insulated cable. The dynamometer (two force plates mounted back‐to‐back on a compression spring and coupled to variable resistances) has been calibrated, statically and in a flume, to obtain velocity determinations accurate to within 10 cm . sec^?1 of true flow speed. Average swash zone velocities lie between 100 and 300 cm . sec^?1.

A parallel‐wire resistance gauge mounted an a stilling tube records flow depths. As water level rises and falls in the tube it alters resistance in a control circuit. The land unit, amplifiers and a strip‐chart recorder, receives the output from the dynamometer and flow depth gauge. The recorder is equipped with a trip‐pen so that analysis of wave periods or other variables is possible in the field. With poles at known spacings across the shore and the trip‐pen records, velocity distributions across the swash zone can be obtained. Measurements of velocity made near the bed with the dynamometer can then be related to the local surface velocity profile.

Problems with the instrument system include inability to record velocities at several points simultaneously, and unreliable records of backwash parameters with low breakers on shingle beaches because of the small volume of flow and rapid percolation of water into the beach face.     

Lagrangian measurements and modelling of fluid advection in the inner surf and swash zones

New laboratory and field data are presented on fluid advection into the swash zone. The data illustrate the region of the inner surf zone from which sediment can be directly advected into the swash zone during a single uprush, which is termed the advection length. Experiments were conducted by particle tracking in a Lagrangian reference frame, and were performed for monochromatic breaking waves, solitary bores, non-breaking solitary waves and field conditions. The advection length is normalised by the run-up length to give an advection ratio, A, and different advection ratios are identified on the basis of the experimental data. The data show that fluid enters the swash zone from a region of the inner surf zone that can extend a distance seaward of the bore collapse location that is approximately equal to half of the run-up length. This region is about eight times wider than the region predicted by the classical swash solution of Shen and Meyer [Shen, M.C., Meyer, R.E., 1963. Climb of a bore on a beach. Part 3. Runup. Journal of Fluid Mechanics 16, 113–125], as illustrated by Pritchard and Hogg [Pritchard, D., Hogg, A.J., 2005. On the transport of suspended sediment by a swash event on a plane beach. Coastal Engineering 52, 1–23]. Measured advection ratios for periodic waves show no significant trend with Iribarren number, consistent with self-similarity in typical swash flows. The data are compared to recent characteristic solutions of the non-linear shallow water wave (NLSW) equations and both finite difference and finite volume solutions of the NLSW equations.     

Measurements and modelling of the advection of suspended sediment in the swash zone by solitary waves

Novel laboratory experiments and numerical modelling have been performed to study the advection scales of suspended sediment in the swash zone. An experiment was designed specifically to measure only the sediment picked up seaward of the swash zone and during bore collapse. The advection scales and settling of this sediment were measured during the uprush along a rigid sediment-free beach face by a sediment trap located at varying cross-shore positions. Measurements were made using a number of repeated solitary broken waves or bores. Approximately 25% of the pre-suspended sediment picked up by the bores reaches the mid-swash zone (50% of the horizontal run-up distance), indicating the importance of the sediment advection in the lower swash zone. The pre-suspended sediment is sourced from a region seaward of the shoreline (still water line) which has a width of about 20% of the run-up distance. An Eulerian–Lagrangian numerical model is used to model the advection scales of the suspended sediment. The model resolves the hydrodynamics by solving the non-linear shallow water equations in an Eulerian framework and then solves the advection–diffusion equation for turbulence and suspended sediment in a Lagrangian framework. The model provides good estimates of the measured mass and distribution of sediment advected up the beach face. The results suggest that the correct modelling of turbulence generation prior to and during bore collapse and the advection of the turbulent kinetic energy into the lower swash is important in resolving the contribution of pre-suspended sediment to the net sediment transport in the swash zone.     

Field investigation on the results of non-linear shallow water equations in the Swash Zone

For the study of the cross-shore wave-induced hydrodynamics in the swash zone, a numerical model is developed based on the one-dimensional non-linear shallow water (NSW) equations for prediction of hydrodynamic parameters in the swash zone. In order to evaluate the accuracy of the outputs of the numerical model, the model's predictions in terms of water surface elevations and cross-shore velocities, are compared to field data from full-scale experiments conducted on three sites with different beach slope; mild and steep, several bed particle sizes and under various incident wave conditions. The quantitative and qualitative comparison of the results of the numerical model and the full-scale data reveals that the model can generally predict many aspects of the flow in the surf and swash zone on both types of beach. The accuracy is adequate for application in a sediment transport study. Considering the time-history and probability distribution of water surface elevation, the model is generally more accurate on steep beaches than on the mild beach. The model can adequately simulate the dominant frequency across the beach and saturation of higher frequencies on both mild and steep beaches for various incident wave energy characteristics. With regard to the horizontal (cross-shore) velocity, the sawtooth shape of time-history and negative acceleration of water are well predicted by the model for both mild and steep beaches. Due to the uncertainties in maximum and minimum values of velocity data, clear judgement about the accuracy of the numerical model in this matter was not possible. However, the comparison of the minimum velocities (offshore direction) revealed that the application of friction factors below the range which is suggested by literature best match the data.     

Swash zone sediment transport modes

The result of field experiments, designed to investigate the relative proportions of bedload and suspended load, are described. The ratio of bedload to suspended sediment load in the swash zone is examined in both swash and backwash on four beaches by measuring the amounts collected in a sediment trap. Bedload transport is found to dominate the backwash. The relative proportions of bedload and suspended load change over the tidal cycle, with increasing bedload dominance at low tide. The total amount of sediment transported as swash and backwash is noticeably greater at high tide than at low tide. More sediment is transported on the flood tide than on the ebb.     

Modeling sediment transport in the swash zone: A review

A critical review of conceptual and mathematical models developed in recent decades on sediment transport in the swash zone is presented. Numerous studies of the hydrodynamics and sediment transport in the swash zone in recent years have pointed out the importance of swash processes in terms of science advancement and practical applications. Evidently, the hydrodynamics of the swash zone are complex and not fully understood. Key hydrodynamic processes include both high-frequency bores and low-frequency infragravity motions, and are affected by wave breaking and turbulence, shear stresses and bottom friction. The prediction of sediment transport that results from these complex and interacting processes is a challenging task. Besides, sediment transport in this oscillatory environment is affected by high-order processes such as the beach groundwater flow. Most relationships between sediment transport and flow characteristics are empirical, based on laboratory experiments and/or field measurements. Analytical solutions incorporating key factors such as sediment characteristics and concentration, waves and coastal aquifer interactions are unavailable. Therefore, numerical models for wave and sediment transport are widely used by coastal engineers. This review covers mechanisms of sediment transport, important forcing factors, governing equations of wave-induced flow, groundwater interactions, empirical and numerical relations of cross-shore and longshore sediment transport in the swash zone. Major advantages and shortcomings of various numerical models and approaches are highlighted and reviewed. These will provide coastal modelers an impetus for further detailed investigations of fluid and sediment transport in the swash zone.     

Formula for predicting bedload transport rate in oscillatory sheet flows

At high bed shear stress sheet flows often occur in coastal waters in which high-concentration bedload sediments are transported in a thin layer near the bed. This paper firstly constructs a theoretical model (partial differential equations, PDEs) for the intense transport of non-cohesive bedload sediments by unidirectional currents and then seeks a special solution to the PDEs to determine the thickness of the bedload particle–water mixture, which could serve as the “reference height” that is often invoked in numerical computation and simulation of suspended sediment transport in turbulent flows. Moreover, a modified formula is presented to determine the “reference concentration”. Using a “uch” approach the present study derives a 1D formula for predicting bedload transport rate in sheet flows driven by asymmetric waves, with the help of a novel formula for evaluating wave friction factor. The new bedload formula can generically take into account slope angle (positive and negative), wash load concentration in the driving water flow and other factors that affect bedload transport rate. It compares well with measured data in a large-scale wave flume [Dohmen-Janssen, C.M., Hanes, D.M., 2002. Sheet flow dynamics under monochromatic non-breaking waves. Journal of Geophysical Research, 107(C10), 1301–1321], a large-scale oscillatory water tunnel [ Hassan, W.N., Ribberink, J.S., 2005. Transport processes of uniform and mixed sands in oscillatory sheet flow. Coastal Engineering, 52, 745–770] and in a swash zone of natural beach [Masselink, G., Hughes, M.G., 1998. Field investigation of sediment transport in the swash zone. Continental Shelf Research, 18, 1179–1199].     

Numerical study on wave-induced filtration flow across the beach face and its effects on swash zone sediment transport

A numerical model, coupling an analysis of beach groundwater flow with an analysis of swash wave motion over a uniform slope, is presented. Model calculations are performed to investigate the variations of swash-induced filtration flows across the beach face for different input parameters. Swash zone sediment transport under the influence of such filtration flow across the beach face is investigated through modification of effective weight of sediment particle and modification of swash boundary layer thickness. These effects are quantified based on a bed load transport model with a modified Shields parameter.     

Sediment transport and morphodynamics generated by a dam-break swash uprush: Coupled vs uncoupled modeling

The present work analyzes the hydro-morphodynamics characterizing the swash region during the uprush stage. A comparison is illustrated between the sediment transport measured in a series of dam-break experiments and that predicted by the numerical hydro-morphodynamic model of Postacchini et al. (2012). The primary aim is to investigate the differences arising between the weakly coupled or uncoupled model and the measurements, in terms of hydrodynamics, tip celerity and sediment transport. The hydrodynamics are well described by the model and results have been used to calibrate both friction factor and subgrid turbulent viscosity. Comparison of numerically-computed tip celerity with experimental data reveals a fairly good agreement, i.e. a mean error of about 10%, while modeled sediment transport differs by about 40% from the available data. No evident differences are found between results obtained from the coupled and uncoupled model runs (2% for the celerity and 11% for the sediment transport rate at the tip), suggesting that for the specific flow under investigation, at the leading edge of the swash front, hydro-morphological coupling is not an issue of fundamental importance. However, for the special case here of a swash forced by a dam-break, scour occurs at the dam location, and in this case the erosion of the bed is significantly larger in the uncoupled model.